arXiv subjects

Anna Rita Altamura

Publications and source records attributed to Anna Rita Altamura.

6 recordsLinked to original sources

arXiv2026

Gain-Layer Project

Gain-layer degradation from exposure to radiation limits the use of Low-Gain Avalanche Diodes (LGADs) in high energy particle physics detector experiments. Proper understanding of how the gain-layer is destroyed is not available on a defect level. Only measurements for materials with much lower effective doping concentrations are available. The direct study of the gain-layer is not possible with typical defect spectroscopy measurements like Thermally Stimulated Currents (TSC) and Deep-Level Transient Spectroscopy (DLTS). To combat this problem and gain a better understanding of the processes which degrade LGADs, the Gain-Layer Project was started. This project produced 19050 diodes with various Boron, Phosphorus, Oxygen and Carbon concentrations. The material used is low-resistivity p-type Silicon. The effective doping concentrations are in the order of a LGAD gain-layer. These diodes will serve the defect community in the coming years for various studies. This article introduces this project with detailed descriptions of the diodes, their flavours and their processing, and reports on results from I-V, C-V, SIMS and DLTS measurements on unirradiated diodes.

physics.ins-det↗

arXiv2026

Timing resolution from beam tests on thin LGADs down to 16.6 ps

The paper reports on the timing resolution achieved with Low-Gain Avalanche Diodes (LGADs), optimised for extreme-fluence conditions, at the DESY Test Beam Facility using 4~GeV/c electrons. The LGADs adopt an $n$-in-$p$ technology with a $p^{+}$-type boron gain implant, co-implanted with carbon to mitigate acceptor deactivation due to irradiation. The substrate thickness of the sensors varies from 20 to 45~\micron, with an active area spanning from 0.75~$\times$~0.75 to 1.28~$\times$~1.28~mm$^{2}$. The experimental setup consisted of a 45~\micron-thick trigger sensor with an active area of 3.6~$\times$~3.6~mm$^{2}$, two device-under-test (DUT) planes, and a Photonis micro-channel plate photomultiplier tube (MCP) as a time reference. Data taking was performed at the ambient temperature of the facility, at 18$^{\circ}$C. The gain was measured between 7 and 40 across all non-irradiated sensors in the study. The timing resolution was calculated from a Gaussian fitting of the difference in times of arrival of a particle at the DUT and the MCP, using the constant fraction discriminator technique. A timing resolution of 26.4~\ps was achieved in 45~\micron-thick sensors, down to 16.6~\ps in 20~\micron-thick sensors, in the non-irradiation study. The combination of two 20~\micron-thick LGADs reached a timing resolution of 12.2~\ps. A set of 30~\micron-thick sensors irradiated with neutrons at fluences between 0.4~$\times$~10$^{15}$ and 2.5~$\times$~10$^{15}$~\mevneut were tested in the beam. These irradiated sensors achieved a gain between 7 and 30 using a similar apparatus but cooled with solidified CO$_{2}$ to -42$^{\circ}$C. A timing resolution of 20~\ps was obtained in these irradiated sensors.

physics.ins-det↗

arXiv2025

MuCol Milestone Report No. 7: Consolidated Parameters

This document is comprised of a collection of consolidated parameters for the key parts of the muon collider. These consolidated parameters follow on from the October 2024 Preliminary Parameters Report. Attention has been given to a high-level consistent set of baseline parameters throughout all systems of the complex, following a 10 TeV center-of-mass design. Additional details of the designs contributing to this baseline design are featured in the appendix. Likewise, explorative variations from this baseline set can be found in the appendix. The data is collected from a collaborative spreadsheet and transferred to overleaf.

physics.acc-ph↗

arXiv2025

Compensated LGAD optimisation through van der Pauw test structures

A new gain implant design has recently been introduced to enhance the radiation resistance of low-gain avalanche diodes (LGADs) to the extreme fluences anticipated in future hadron colliders like FCC-hh. This design utilises an engineered compensation of two opposing types of doping implants, requiring a thorough analysis of their evolution due to irradiation. To this end, the experimental measurements of their initial test structures have been compared with Technology CAD simulations both before and after irradiation. From the measurement-simulation comparison regarding C-V characteristics, the donor removal at high initial donor concentrations ($>10^{16}$ at/cm$^3$) used in Compensated LGADs has been studied, along with how donor co-implantation influences the beneficial effect of carbon to slow acceptor removal. Furthermore, an innovative application of van der Pauw test structures, typically employed by foundries to monitor process quality, has been implemented. The doping removal of the single implants used in Compensated LGADs has been estimated by examining the variation in sheet resistance with irradiation through these structures.

physics.ins-det↗

arXiv2025

The Muon Collider

Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an electron-positron collider, yielding a physics potential significantly greater than the sum of its individual parts. A high-energy muon collider is the natural next step in the exploration of fundamental physics after the HL-LHC and a natural complement to a future low-energy Higgs factory. Such a facility would significantly broaden the scope of particle colliders, engaging the many frontiers of the high energy community. The last European Strategy for Particle Physics Update and later the Particle Physics Project Prioritisation Panel in the US requested a study of the muon collider, which is being carried on by the International Muon Collider Collaboration. In this comprehensive document we present the physics case, the state of the work on accelerator design and technology, and propose an R\&D project that can make the muon collider a reality.

physics.acc-ph↗

arXiv2021

Radiation damage on SiPMs for Space Applications

Silicon Photo-multipliers (SiPMs) are very sensitive photo-detectors that experienced a big development in the last years in several applications, like LIDAR, astrophysics, medical imaging and high energy physics (HEP) experiments. In HEP experiments, in particular, they are often exposed to significant radiation doses. The main purpose of this manuscript is the characterization of several FBK SiPM technologies when exposed to 74 $MeV$ protons with a total fluence comparable to the one that they would experience in space along circular Low Earth Orbits (LEO), Polar, during a five years mission. In this work, we estimated the expected proton fluences along the selected orbit, by means of the SPENVIS software. Several fluence steps were chosen to consider dense fluence intervals and have a more accurate sight on the whole damage process. We estimated a maximum fluence achieved during the tests of $6.4 \times 10^{11}$ $n_{eq}/cm^2$. Based on such simulations, we irradiated several SiPM technologies. We developed a custom experimental setup, which was used to perform online reverse voltage-current, right after each irradiation step, to minimize the effect of the annealing on the measurement. The results are then displayed, in particular the currents, the noise and the Photon Detection Efficiency. Also a 30-days study on the annealing of the devices was performed. Lastly, the conclusions are drawn on the basis of the Signal-to-Noise Ratio (SNR), taking into account the standard parameters of famous satellites using similar orbits as the ones considered into this work.

physics.ins-det↗