arXiv subjects

B. Deng

Publications and source records attributed to B. Deng.

13 recordsLinked to original sources

arXiv2023

GBT20, a 20.48 Gbps PAM4 Optical Transmitter Module for Particle Physics Experiments

We present a pluggable radiation-tolerant 4-level Pulse-Amplitude-Modulation (PAM4) optical transmitter module called GBT20 (Giga-Bit Transmitter at 20 Gbps) for particle-physics experiments. GBT20 has an OSFP or firefly connector to input 16-bit data each at 1.28 Gbps. The GBT20 drives a VCSEL die with an LC lens or a VCSEL TOSA and interfaces an optical fiber with a standard LC connector. The minimum module, including the host connector, occupies 41 mm x 13 mm x 6 mm. At 20.48 Gbps, the minimum Transmitter Dispersion Eye Closure Quaternary (TDECQ) is around 0.7 dB. The power consumption is around 164 mW in the low-power mode. The SEE cross-section is below 7.5x10^(-14) cm^2. No significant performance degrades after a TID of 5.4 kGy.

physics.ins-det↗

arXiv2023

The design and test results of A Giga-Bit Cable Receiver (GBCR) for the ATLAS Inner Tracker Pixel Detector

This paper presents the design and test results of a Gigabit Cable Receiver ASIC called GBCR for the HL-LHC upgrade of the ATLAS Inner Tracker (ITk) pixel detector. Three prototypes (GBCR1, GBCR2, and GBCR3) have been designed in the CERN-identified 65 nm CMOS technology. GBCR receives seven (GBCR2) or six (GBCR3) channels (RX) each at 1.28 Gbps from the front-end readout chip RD53B via flex cables up to 1 meter and Twinax cables up to 5 meters and sends the equalized and retimed signals to lpGBT. Both GBCR2 and GBCR3 ASICs have two transmitting channels (TX) that pre-emphasize the signals from lpGBT before sending them to RD53B through the same cables. No Single-Event Upset (SEU) is observed in any tested channels of GBCR2 in a 400 MeV proton beam. The extrapolated bit error rate for the future HL-LHC application is below 8*10^(-16), significantly below the specified BER criterion. GBCR3 is designed to improve the immunity to single-event-upset by applying the Triple Modular Redundancy (TMR) technology to all RX channels. The retimed signals from GBCR3 have less total jitter than those from GBCR2 (35 ps versus 79 ps). Each receiver channel of GBCR3 consumes 75% more power than that of GBCR2.

physics.ins-det↗

arXiv2022

A 40 Gbps Optical Transceiver for Particle Physics Experiments

We present the design and the test results of a quad-channel optical transceiver module (QTRx) possibly for future particle physics experiments. The transmitters of QTRx, each at 10 Gbps, are based on a Quad-channel VCSEL Diode array Driver (QLDD) and 1 x 4 VCSEL array. The receivers of QTRx, with data rates of 2.56 Gbps or 10 Gbps per channel, are based on a Quad-channel Trans-Impedance and limiting Amplifier (QTIA) and 1 x 4 photodiode array of GaAs or InGaAs. QTRx is 20 mm x 10 mm x 5 mm and couples to an MT fiber connector. Test results indicate that QTRx achieves the design goals with a power consumption of 124 mW per transmitter channel at 10 Gbps and 120 mW at 2.56 Gbps for the receiver channel with an on-chip charge pump. The sensitivities of QTIA are -17 dBm at 2.56 Gbps and -8 dBm at 10 Gbps, respectively. Further improvements with a gold-finger interface and a more compact optical lens are being designed.

physics.ins-det↗

arXiv2022

A prototype optical link board with redundancy design for the ATLAS liquid argon calorimeter Phase-2 upgrade

A prototype optical-link board has been developed for the ATLAS Liquid Argon Calorimeter Phase-2 upgrade. The board consists of 24 lpGBT chips and 8 VTRx+ modules and demonstrates the full optical link design of the future front-end board. The board has 22 simplex optical links to transmit detector data, which are emulated in FPGAs and injected through 6 FMC connectors, to the off-detector electronics. The board implements 2 duplex optical links for clocks, control, and monitoring with redundant design to improve the system reliability. Data transmission and all redundant designs have been verified. A fiber routing scheme, in which 2 or 3 VTRx+ modules are re-connected to the front panel with an MPO connector, has been prototyped.

physics.ins-det↗

arXiv2022

The Phase-I Trigger Readout Electronics Upgrade of the ATLAS Liquid Argon Calorimeters

The Phase-I trigger readout electronics upgrade of the ATLAS Liquid Argon calorimeters enhances the physics reach of the experiment during the upcoming operation at increasing Large Hadron Collider luminosities. The new system, installed during the second Large Hadron Collider Long Shutdown, increases the trigger readout granularity by up to a factor of ten as well as its precision and range. Consequently, the background rejection at trigger level is improved through enhanced filtering algorithms utilizing the additional information for topological discrimination of electromagnetic and hadronic shower shapes. This paper presents the final designs of the new electronic elements, their custom electronic devices, the procedures used to validate their proper functioning, and the performance achieved during the commissioning of this system.

physics.ins-det↗

arXiv2022

A 20 Gbps PAM4 Data Transmitter ASIC for Particle Physics Experiments

We present the design and test results of a novel data transmitter ASIC operating up to 20.48 Gbps with 4-level Pulse-Amplitude-Modulation (PAM4) for particle physics experiments. This ASIC, named GBS20, is fabricated in a 65 nm CMOS technology. Two serializers share a 5.12 GHz Phase Locked Loop (PLL) clock. The outputs from the serializers are combined into a PAM4 signal that directly drives a Vertical-Cavity-Surface-Emitting-Laser (VCSEL). The input data channels, each at 1.28 Gbps, are scrambled with an internal 27-1 Pseudo-Random Binary Sequence (PRBS), which also serves as a frame aligner. GBS20 is tested to work at 10.24 and 20.48 Gbps with a VCSEL-based Transmitter-Optical-Subassembly (TOSA). The power consumption of GBS20 is below 238 mW and reduced to 164 mW in the low-power mode.

physics.ins-det↗

arXiv2021

QTIA, a 2.5 or 10 Gbps 4-Channel Array Optical Receiver ASIC in a 65 nm CMOS Technology

The Quad transimpedance and limiting amplifier (QTIA) is a 4-channel array optical receiver ASIC, developed using a 65 nm CMOS process. It is configurable between the bit rate of 2.56 Gbps and 10 Gbps per channel. QTIA offers careful matching to both GaAs and InGaAs photodiodes. At this R&D stage, each channel has a different biasing scheme to the photodiode for optimal coupling. A charge pump is implemented in one channel to provide a higher reverse bias voltage, which is especially important to mitigate radiation effects on the photodiodes. The circuit functions of QTIA successfully passed the lab tests with GaAs photodiodes.

physics.ins-det↗

arXiv2021

Quality control tests of the front-end optical link components for the ATLAS Liquid Argon Calorimeter Phase-1 upgrade

We present the procedures and results of the quality control tests for the front-end optical link components in the ATLAS Liquid Argon Calorimeter Phase-1 upgrade. The components include a Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC LOCld, custom optical transmitter/transceiver modules MTx/MTRx, and a transmitter ASIC LOCx2. LOCld, MTx, and LOCx2 each contain two channels with the same structure, while MTRx has a transmitter channel and a receiver channel. Each channel is tested at 5.12 Gbps. A total of 5341 LOCld chips, 3275 MTx modules, 797 MTRx modules, and 3198 LOCx2 chips are qualified. The yields are 73.9%, 98.0%, 98.4%, and 61.9% for LOCld, LOCx2, MTx, and MTRx, respectively.

physics.ins-det↗

arXiv2021

Machine learning of superconducting critical temperature from Eliashberg theory

The Eliashberg theory of superconductivity accounts for the fundamental physics of conventional electron-phonon superconductors, including the retardation of the interaction and the effect of the Coulomb pseudopotential, to predict the critical temperature $T_c$ and other properties. McMillan, Allen, and Dynes derived approximate closed-form expressions for the critical temperature predicted by this theory, which depends essentially on the electron-phonon spectral function $\alpha^2F(\omega)$, using $\alpha^2F$ for low-$T_c$ superconductors. Here we show that modern machine learning techniques can substantially improve these formulae, accounting for more general shapes of the $\alpha^2F$ function. Using symbolic regression and the sure independence screening and sparsifying operator (SISSO) framework, together with a database of artificially generated $\alpha^2F$ functions, ranging from multimodal Einstein-like models to calculated spectra of polyhydrides, as well as numerical solutions of the Eliashberg equations, we derive a formula for $T_c$ that performs as well as Allen-Dynes for low-$T_c$ superconductors, and substantially better for higher-$T_c$ ones. The expression identified through our data-driven approach corrects the systematic underestimation of $T_c$ while reproducing the physical constraints originally outlined by Allen and Dynes. This equation should replace the Allen-Dynes formula for the prediction of higher-temperature superconductors and for the estimation of $\lambda$ from experimental data.

cond-mat.supr-con↗

arXiv2020

A TOSA/ROSA-Based Optical Transmitter (MTx+)/Transceiver (MTRx+) for High-Energy Physics Experiments

We present a dual-channel optical transmitter (MTx+)/transceiver (MTRx+) for the front-end readout electronics of high-energy physics experiments. MTx+ utilizes two Transmitter Optical Sub-Assemblies (TOSAs) and MTRx+ utilizes a TOSA and a Receiver Optical Sub-Assemblies (ROSA). Both MTx+ and MTRx+ receive multimode fibers with standard Lucent Connectors (LCs) as the optical interface and can be panel or board mounted to a motherboard with a standard Enhanced Small Form-factor Pluggable (SFP+) connector as the electrical interface. MTx+ and MTRx+ employ a dual-channel Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC called LOCld65, which brings the transmitting data rate up to 14 Gbps per channel. MTx+ and MTRx+ have been tested to survive 4.9 kGy(SiO2).

physics.ins-det↗

arXiv2020

Design and hardware evaluation of the optical-link system for the ATLAS Liquid Argon Calorimeter Phase-II Upgrade

An optical link system is being developed for the ATLAS Liquid Argon Calorimeter Phase-II upgrade. The optical link system is responsible for transmit the data of over 182 thousand detector channels from 1524 Front-End Boards (FEBs) through 26 optical fibers per FEB over 150 meters to the counting room and brings clocks, bunch crossing reset signals and slow control/monitoring signals back to the FEBs. The optical link system is based on the Low-Power GigaBit Transceivers (lpGBTs) and the Versatile optical Transceiver (VTRx+) modules, which both are being developed for the High-Luminosity LHC upgrade. An evaluation board is designed and the major functions of the optical link system are being evaluated. The design of the optical link system and the evaluation of major functions are presented in the paper.

physics.ins-det↗

arXiv2006

Enhancing structure relaxations for first-principles codes: an approximate Hessian approach

We present a method for improving the speed of geometry relaxation by using a harmonic approximation for the interaction potential between nearest neighbor atoms to construct an initial Hessian estimate. The model is quite robust, and yields approximately a 30% or better reduction in the number of calculations compared to an optimized diagonal initialization. Convergence with this initializer approaches the speed of a converged BFGS Hessian, therefore it is close to the best that can be achieved. Hessian preconditioning is discussed, and it is found that a compromise between an average condition number and a narrow distribution in eigenvalues produces the best optimization.

physics.comp-ph↗

arXiv2006

A Surface Reconstruction with a Fractional Hole: $(\sqrt{5}\times\sqrt{5}) R26.6^\circ$ LaAlO$_3$ (001)

The structure of the $(\sqrt{5}\times\sqrt{5})R26.6^\circ$ reconstruction of LaAlO$_3$ (001) has been determined using transmission electron diffraction combined with direct methods. The structure is relatively simple, consisting of a lanthanum oxide termination with one lanthanum cation vacancy per surface unit cell. The electronic structure is unusual since a fractional number of holes or atomic occupancies per surface unit cell are required to achieve charge neutrality. Density functional calculations indicate that the charge compensation mechanism occurs by means of highly delocalized holes. The surface contains no oxygen vacancies and with a better than 99% confidence level, the holes are not filled with hydrogen. The reconstruction can be understood in terms of expulsion of the more electropositive cation from the surface followed by an increased covalency between the remaining surface lanthanum atoms and adjacent oxygen atoms.

cond-mat.mtrl-sci↗