arXiv subjects

B. Dieny

Publications and source records attributed to B. Dieny.

At least 19 recordsLinked to original sources

arXiv2023

Dipolar coupled core-shell perpendicular shape anisotropy MTJ with enhanced write speed and reduced cross-talk

The concept of Perpendicular Shape-Anisotropy Spin-Transfer-Torque Magnetic Random-Access Memory tackles the downsize scalability limit of conventional ultrathin magnetic tunnel junctions (MTJ) below sub-20 nm technological nodes. This concept uses a thicker storage layer with a vertical aspect ratio, enhancing the thermal stability factor thanks to the favorable contribution of the shape anisotropy. However, the increased aspect ratio comes with an increase in switching time under applied voltage and the cross-over to non-uniform reversal mechanism at higher aspect ratio, limiting the gain in scalability. Additionally, the larger volume of the magnetic cell significantly increases the stray field acting on the neighboring devices compared to thin MTJs. In this work, we propose the use of a dipolar-coupled core-shell system as a storage layer. This improves both bottlenecks, as predicted by micromagnetic simulations for magnetisation reversal, and a macrospin model to estimate the stray field in a dense array.

cond-mat.mes-hall↗

arXiv2023

Field-free all-optical switching and electrical read-out of Tb/Co-based magnetic tunnel junctions

Switching of magnetic tunnel junction using femto-second laser enables a possible path for THz frequency memory operation, which means writing speeds 2 orders of magnitude faster than alternative electrical approaches based on spin transfer or spin orbit torque. In this work we demonstrate successful field-free 50fs single laser pulse driven magnetization reversal of [Tb/Co] based storage layer in a perpendicular magnetic tunnel junction. The nanofabricated magnetic tunnel junction devices have an optimized bottom reference electrode and show Tunnel Magnetoresistance Ratio values (TMR) up to 74\% after patterning down to sub-100nm lateral dimensions. Experiments on continuous films reveal peculiar reversal patterns of concentric rings with opposite magnetic directions, above certain threshold fluence. These rings have been correlated to patterned device switching probability as a function of the applied laser fluence. Moreover, the magnetization reversal is independent on the duration of the laser pulse. According to our macrospin model, the underlying magnetization reversal mechanism can be attributed to an in-plane reorientation of the magnetization due to a fast reduction of the out-of-plane uniaxial anisotropy. These aspects are of great interest both for the physical understanding of the switching phenomenon and their consequences for all-optical-switching memory devices, since they allow for a large fluence operation window with high resilience to pulse length variability.

physics.app-ph↗

arXiv2021

Size-dependent enhancement of passive microwave rectification in magnetic tunnel junctions with perpendicular magnetic anisotropy

Spintronic rf detectors were demonstrated, recently, for energy harvesting and wireless communication at low input power. Here we report on the optimization of the rectified output dc voltage using magnetic tunnel junctions (MTJ) with strong perpendicular anisotropy (PMA) of both the polarizing and the free layer. The magnetization of the polarizing layer is fixed out of plane, while the free layer thickness is adjusted so that its magnetization orientation changes from in plane to out of plane. The rectification dc output voltage lies in the mV range for moderate rf powers, with a signal to noise ratio of 10 to 100 for Prf = -25dBm. It shows a strong dependence on the dimensions of the MTJ: it increases by a factor of 5 to 6 when reducing the diameter from 150nm to 20nm. This enhancement can be doubled when reducing the FL thickness from 1.8nm to 1.6nm. This dimensional enhancement is attributed to the change of the effective anisotropy of the excited free layer, and the MTJ resistance. The results are of interest for the design of spintronic based rf detectors with optimized sensitivity.

cond-mat.mes-hall↗

arXiv2021

Mutual Synchronization of Spin-Torque Oscillators within a Ring Array

An array of spin torque nano-oscillators (STNOs), coupled by dipolar interaction and arranged on a ring, has been studied numerically and analytically. The phase patterns and locking ranges are extracted as a function of the number $N$, their separation, and the current density mismatch between selected subgroups of STNOs. If $N\geq 6$ for identical current densities through all STNOs, two degenerated modes are identified an in-phase mode (all STNOs have the same phase) and an out-of-phase mode (the phase makes a 2$π$ turn along the ring). When inducing a current density mismatch between two subgroups, additional phase shifts occur. The locking range (maximum current density mismatch) of the in-phase mode is larger than the one for the out-of-phase mode and depends on the number $N$ of STNOs on the ring as well as on the separation. These results can be used for the development of magnetic devices that are based on STNO arrays.

cond-mat.soft↗

arXiv2021

Magnetization reversal driven by spin-transfer-torque in perpendicular shape anisotropy magnetic tunnel junctions

The concept of perpendicular shape anisotropy spin-transfer torque magnetic random-access memory (PSA-STT-MRAM) consists in increasing the storage layer thickness to values comparable to the cell diameter, to induce a perpendicular shape anisotropy in the magnetic storage layer. Making use of that contribution, the downsize scalability of the STT-MRAM may be extended towards sub-20 nm technological nodes, thanks to a reinforcement of the thermal stability factor $Δ$. Although the larger storage layer thickness improves $Δ$, it is expected to negatively impact the writing current and switching time. Hence, optimization of the cell dimensions (diameter, thickness) is of utmost importance for attaining a sufficiently high $Δ$ while keeping a moderate writing current. Micromagnetic simulations were carried out for different pillar thicknesses of fixed lateral size 20 nm. The switching time and the reversal mechanism were analysed as a function of the applied voltage and aspect-ratio (AR) of the storage layer. For AR $<$ 1, the magnetization reversal resembles a macrospin-like mechanism, while for AR $>$ 1 a non-coherent reversal is observed, characterized by the nucleation of a transverse domain wall at the ferromagnet/insulator interface which then propagates along the vertical axis of the pillar. It was further observed that the inverse of the switching time is linearly dependent on the applied voltage. This study was extended to sub-20 nm width with a value of $Δ$ around 80. It was observed that the voltage necessary to reverse the magnetic layer increases as the lateral size is reduced, accompanied with a transition from macrospin-reversal to a buckling-like reversal at high aspect-ratios.

cond-mat.mes-hall↗

arXiv2020

Experimental demonstration of a rapid sweep-tuned spectrum analyzer with temporal resolution based on a spin-torque nano-oscillator

It is demonstrated experimentally that a spin-torque nano-oscillator (STNO) rapidly sweep-tuned by a bias voltage can be used for time-resolved spectrum analysis of frequency-manipulated microwave signals with complicated multi-tone spectra. The critical reduction in the time of spectrum analysis comes from the naturally small time constants of a nano-sized STNO (1-100 ns). The demonstration is performed on a vortex-state STNO generating in a frequency range around 300 MHz, with frequency down-conversion and matched filtering used for signal processing. It is shown that this STNO-based spectrum analyzer can perform analysis of multi-tone signals, and signals with rapidly changing frequency components with time resolution on a $μ$s time scale and frequency resolution limited only by the 'bandwidth' theorem. The proposed concept of rapid time-resolved spectrum analysis can be implemented with any type of micro and nano-scale frequency-swept oscillators having low time constants and high oscillation frequency.

physics.app-ph↗

arXiv2019

Analog and digital phase modulation of spin torque nano-oscillators

Spin torque nano-oscillators (STNO) are nanoscale devices with wide band frequency tunability. Their multifunctional RF properties are well suited to define novel schemes for wireless communications that use basic protocols for data transmission such as amplitude, frequency and phase shift keying (ASK, FSK, PSK). In contrast to ASK and FSK, implementation of PSK is more challenging for STNOs because of their relatively high phase noise. Here we introduce a special PSK technique by combining their modulation and injection locking functionality. The concept is validated using magnetic tunnel junction based vortex STNOs for injection locking at 2f and f/2 showing phase shifts up to 2.1rad and data transmission rates up to 4Mbit/s. Quadrature phase shift keying and analog phase modulation are also implemented, where the latter is employed for voice transmission over a distance of 10 meters. This demonstrates that STNO phase noise and output power meet the requested performances for operation in existing communication schemes.

physics.app-ph↗

arXiv2018

Giant variation of the perpendicular magnetic anisotropy at Fe/MgO interfaces by oxygen migration: a first-principles study

A characteristic dependence of voltage control of perpendicular magnetic anisotropy (VCMA) on oxygen migration at Fe/MgO interfaces was revealed by performing systematic {\it ab initio} study of the energetics of the oxygen path around the interface. We find that the surface anisotropy energy exhibits a Boltzmann sigmoidal behavior as a function of the migrated O-atoms concentration. The obtained variation of the VCMA efficiency factor $β$ reveals a saturation limit beyond a critical concentration of migrated O, about $54\%$, at which the anisotropy switches from perpendicular to in plane. Furthermore, depending on the range of variation of the applied voltage, two regimes associated with reversible or irreversible ions displacement are predicted to occur, yielding different VCMA response. According to our findings, one can distinguish from the order of magnitude of $β$ the VCMA driving mechanism: an effect of several tens of fJ/(V.m) is likely associated to charge-mediated effect combined with slight reversible oxygen displacements whereas an effect of the order of thousands of fJ/(V.m) is more likely associated with irreversible oxygen ionic migration.

cond-mat.mtrl-sci↗

arXiv2018

Highly thermally stable sub-20nm magnetic random-access memory based on perpendicular shape anisotropy

A new approach to increase the downsize scalability of perpendicular STT-MRAM is presented. It consists in significantly increasing the thickness of the storage layer in out-of-plane magnetized tunnel junctions (pMTJ) as compared to conventional pMTJ in order to induce a perpendicular shape anisotropy (PSA) in this layer. This PSA is obtained by depositing a thick ferromagnetic (FM) layer on top of an MgO/FeCoB based magnetic tunnel junction (MTJ) so that the thickness of the storage layer becomes of the order or larger than the diameter of the MTJ pillar. In contrast to conventional spin transfer torque magnetic random access memory (STT-MRAM) wherein the demagnetizing energy opposes the interfacial perpendicular magnetic anisotropy (iPMA), in these novel memory cells, both PSA and iPMA contributions favor out-of-plane orientation of the storage layer magnetization. Using thicker storage layers in these PSA-STT-MRAM has several advantages. Thanks to the PSA, very high and easily tunable thermal stability factors can be achieved, even down to sub-10 nm diameters. Moreover, low damping material can be used for the thick FM material thus leading to a reduction of the write current. The paper describes this new PSA-STT-MRAM concept, practical realization of such memory arrays, magnetic characterization demonstrating thermal stability factor above 200 for MTJs as small as 8nm in diameter and possibility to maintain thermal stability factor above 60 down to 4nm diameter.

cond-mat.mtrl-sci↗

arXiv2016

Steady State and Dynamics of Joule Heating in Magnetic Tunnel Junctions Observed via the Temperature Dependence of RKKY Coupling

Understanding quantitatively the heating dynamics in magnetic tunnel junctions (MTJ) submitted to current pulses is very important in the context of spin-transfer-torque magnetic random access memory development. Here we provide a method to probe the heating of MTJ using the RKKY coupling of a synthetic ferrimagnetic storage layer as a thermal sensor. The temperature increase versus applied bias voltage is measured thanks to the decrease of the spin-flop field with temperature. This method allows distinguishing spin transfer torque (STT) effects from the influence of temperature on the switching field. The heating dynamics is then studied in real-time by probing the conductance variation due to spin-flop rotation during heating. This approach provides a new method for measuring fast heating in spintronic devices, particularly magnetic random access memory (MRAM) using thermally assisted or spin transfer torque writing.

cond-mat.mtrl-sci↗

arXiv2016

Second order anisotropy contribution in perpendicular magnetic tunnel junctions

Magnetoresistance loops under in-plane applied field were measured on perpendicularly magnetized magnetic tunnel junction (pMTJ) pillars with nominal diameters ranging from 50 to 150 nm. By fitting the hard-axis magnetoresistance loops to an analytical model, the effective anisotropy fields in both free and reference layers were derived and their variations in temperature range between 340K and 5K were determined. It is found that an accurate fitting is possible only if a second-order anisotropy term of the form $-K_{2}cos^4θ$, is added to the fitting model. This higher order contribution exists both in the free and reference layers and its sign is opposite to that of the first order anisotropy constant, $K_{1}$. At room temperatures the estimated $-K_{2}/K_{1}$ ratios are 0.1 and 0.24 for the free and reference layers, respectively. The ratio is more than doubled at low temperatures altering the ground state of the reference layer from 'easy-axis' to 'easy-cone' regime. Easy-cone state has clear signatures in the shape of the hard-axis magnetoresistance loops. The same behavior was observed in all measured devices regardless of their diameter. The existence of this higher order anisotropy was confirmed experimentally on FeCoB/MgO sheet films by ferromagnetic resonance technique. It is of interfacial nature and is believed to be linked to spatial fluctuations at the nanoscale of the anisotropy parameter at the FeCoB/MgO interface, in agreement with Dieny-Vedyayev model.

cond-mat.mes-hall↗

arXiv2015

Analytical description of ballistic spin currents and torques in magnetic tunnel junctions

In this work we demonstrate explicit analytical expressions for both charge and spin currents which constitute the 2x2 spinor in magnetic tunnel junctions with noncollinear magnetizations under applied voltage. The calculations have been performed within the free electron model in the framework of the Keldysh formalism and WKB approximation. We demonstrate that spin/charge currents and spin transfer torques are all explicitly expressed through only three irreducible quantities, without further approximations. The conditions and mechanisms of deviation from the conventional sine angular dependence of both spin currents and torques are shown and discussed. It is shown in the thick barrier approximation that all tunneling transport quantities can be expressed in an extremely simplified form via Slonczewski spin polarizations and our effective spin averaged interfacial transmission probabilities and effective out-of-plane polarizations at both interfaces. It is proven that the latter plays a key role in the emergence of perpendicular spin torque as well as in the angular dependence character of all spin and charge transport considered. It is demonstrated directly also that for any applied voltage, the parallel component of spin current at the FM/I interface is expressed via collinear longitudinal spin current components. Finally, spin transfer torque behavior is analyzed in a view of transverse characteristic length scales for spin transport.

cond-mat.mes-hall↗

arXiv2015

Respective influence of in-plane and out-of-plane spin-transfer torques in magnetization switching of perpendicular magnetic tunnel junctions

The relative contributions of in-plane (damping-like) and out-of-plane (field-like) spin-transfer-torques in the magnetization switching of out-of-plane magnetized magnetic tunnel junctions (pMTJ) has been theoretically analyzed using the transformed Landau-Lifshitz (LL) equation with the STT terms. It is demonstrated that in a pMTJ structure obeying macrospin dynamics, the out-of-plane torque influences the precession frequency but it does not contribute significantly to the STT switching process (in particular to the switching time and switching current density), which is mostly determined by the in-plane STT contribution. This conclusion is confirmed by finite temperature and finite writing pulse macrospin simulations of the current-field switching diagrams. It contrasts with the case of STT-switching in in-plane magnetized MTJ in which the field-like term also influences the switching critical current. This theoretical analysis was successfully applied to the interpretation of voltage-field STT switching diagrams experimentally measured on perpendicular MTJ pillars 36 nm in diameter, which exhibit macrospin-like behavior. The physical nonequivalence of Landau and Gilbert dissipation terms in presence of STT-induced dynamics is also discussed.

cond-mat.mes-hall↗

arXiv2014

Modulating spin transfer torque switching dynamics with two orthogonal spin-polarizers by varying the cell aspect ratio

We study in-plane magnetic tunnel junctions with additional perpendicular polarizer for subnanosecond-current-induced switching memories. The spin-transfer-torque switching dynamics was studied as a function of the cell aspect ratio both experimentally and by numerical simulations using the macrospin model. We show that the anisotropy field plays a significant role in the dynamics, along with the relative amplitude of the two spin-torque contributions. This was confirmed by micromagnetic simulations. Real-time measurements of the reversal were performed with samples of low and high aspect ratio. For low aspect ratios, a precessional motion of the magnetization was observed and the effect of temperature on the precession coherence was studied. For high aspect ratios, we observed magnetization reversals in less than 1 ns for high enough current densities, the final state being controlled by the current direction in the magnetic tunnel junction cell.

cond-mat.mes-hall↗

arXiv2014

Impurity induced enhancement of perpendicular magnetic anisotropy in Fe/MgO tunnel junctions

Using first-principles calculations, we investigated the impact of chromium (Cr) and vanadium (V) impurities on the magnetic anisotropy and spin polarization in Fe/MgO magnetic tunnel junctions. It is demonstrated using layer resolved anisotropy calculation technique, that while the impurity near the interface has a drastic effect in decreasing the perpendicular magnetic anisotropy (PMA), its position within the bulk allows maintaining high surface PMA. Moreover, the effective magnetic anisotropy has a strong tendency to go from in-plane to out-of-plane character as a function of Cr and V concentration favoring out-of-plane magnetization direction for ~1.5 nm thick Fe layers at impurity concentrations above 20 %. At the same time, spin polarization is not affected and even enhanced in most situations favoring an increase of tunnel magnetoresistance (TMR) values.

cond-mat.mtrl-sci↗

arXiv2013

Anatomy of perpendicular magnetic anisotropy in Fe/MgO magnetic tunnel junctions: First principles insight

Using first-principles calculations, we elucidate microscopic mechanisms of perpendicular magnetic anisotropy (PMA)in Fe/MgO magnetic tunnel junctions through evaluation of orbital and layer resolved contributions into the total anisotropy value. It is demonstrated that the origin of the large PMA values is far beyond simply considering the hybridization between Fe-3d$ and O-2p orbitals at the interface between the metal and the insulator. On-site projected analysis show that the anisotropy energy is not localized at the interface but it rather propagates into the bulk showing an attenuating oscillatory behavior which depends on orbital character of contributing states and interfacial conditions. Furthermore, it is found in most situations that states with $d_{yz(xz)}$ and $d_{z^2}$ character tend always to maintain the PMA while those with $d_{xy}$ and $d_{x^2-y^2}$ character tend to favor the in-plane anisotropy. It is also found that while MgO thickness has no influence on PMA, the calculated perpendicular magnetic anisotropy oscillates as a function of Fe thickness with a period of 2ML and reaches a maximum value of 3.6 mJ/m$^2$.

cond-mat.mtrl-sci↗

arXiv2012

Artificial ferroelectricity due to anomalous Hall effect in magnetic tunnel junctions

We theoretically investigated Anomalous Hall Effect (AHE) and Spin Hall Effect (SHE) transversally to the insulating spacer O, in magnetic tunnel junctions of the form F/O/F where F are ferromagnetic layers and O represents a tunnel barrier. We considered the case of purely ballistic (quantum mechanical) transport, taking into account the assymetric scattering due to spin-orbit interaction in the tunnel barrier. AHE and SHE in the considered case have a surface nature due to proximity effect. Their amplitude is in first order of the scattering potential. This contrasts with ferromagnetic metals wherein these effect are in second (side-jump scattering) and third (skew scattering) order on these potentials. The value of AHE voltage in insulating spacer may be much larger than in metallic ferromagnetic electrodes. For the antiparallel orientation of the magnetizations in the two F-electrodes, a spontaneous Hall voltage exists even at zero applied voltage. Therefore an insulating spacer sandwiched between two ferromagnetic layers can be considered as exhibiting a spontaneous ferroelectricity.

cond-mat.mes-hall↗

arXiv2011

Temperature dependence of the emission linewidth in MgO-based spin torque nano-oscillators

Spin transfer driven excitations in magnetic nanostructures are characterized by a relatively large microwave emission linewidth (10 -100 MHz). Here we investigate the role of thermal fluctuations as well as of the non-linear amplitude-phase coupling parameter and the amplitude relaxation rate to explain the linewidth broadening of in-plane precession modes induced in planar nanostructures. Experiments on the linewidth broadening performed on MgO based magnetic tunnel junctions are compared to the linewidth obtained from macrospin simulations and from evaluation of the phase variance. In all cases we find that the linewidth varies linearly with temperature when the amplitude relaxation rate is of the same order as the linewidth and when the amplitude-phase coupling parameter is relatively small. The small amplitude-phase coupling parameter means that the linewidth is dominated by direct phase fluctuations and not by amplitude fluctuations, explaining thus its linear dependence as a function of temperature.

cond-mat.mes-hall↗