arXiv subjects

Barnaby Norris

Publications and source records attributed to Barnaby Norris.

At least 55 records · Page 3Linked to original sources

arXiv2022

Achromatic design of a photonic tricoupler and phase shifter for broadband nulling interferometry

Nulling interferometry is one of the most promising technologies for imaging exoplanets within stellar habitable zones. The use of photonics for carrying out nulling interferometry enables the contrast and separation required for exoplanet detection. So far, two key issues limiting current-generation photonic nullers have been identified: phase variations and chromaticity within the beam combiner. The use of tricouplers addresses both limitations, delivering a broadband, achromatic null together with phase measurements for fringe tracking. Here, we present a derivation of the transfer matrix of the tricoupler, including its chromatic behaviour, and our 3D design of a fully symmetric tricoupler, built upon a previous design proposed for the GLINT instrument. It enables a broadband null with symmetric, baseline-phase-dependent splitting into a pair of bright channels when inputs are in anti-phase. Within some design trade space, either the science signal or the fringe tracking ability can be prioritised. We also present a tapered-waveguide $180^\circ$-phase shifter with a phase variation of $0.6^\circ$ in the $1.4-1.7~μ$m band, producing a near-achromatic differential phase between beams{ for optimal operation of the tricoupler nulling stage}. Both devices can be integrated to deliver a deep, broadband null together with a real-time fringe phase metrology signal.

astro-ph.IM↗

arXiv2022

Efficient detection and characterization of exoplanets within the diffraction limit: nulling with a mode-selective photonic lantern

Coronagraphs allow for faint off-axis exoplanets to be observed, but are limited to angular separations greater than a few beam widths. Accessing closer-in separations would greatly increase the expected number of detectable planets, which scales inversely with the inner working angle. The Vortex Fiber Nuller (VFN) is an instrument concept designed to characterize exoplanets within a single beam-width. It requires few optical elements and is compatible with many coronagraph designs as a complementary characterization tool. However, the peak throughput for planet light is limited to about 20%, and the measurement places poor constraints on the planet location and flux ratio. We propose to augment the VFN design by replacing its single-mode fiber with a six-port mode-selective photonic lantern, retaining the original functionality while providing several additional ports that reject starlight but couple planet light. We show that the photonic lantern can also be used as a nuller without a vortex. We present monochromatic simulations characterizing the response of the Photonic Lantern Nuller (PLN) to astrophysical signals and wavefront errors, and show that combining exoplanet flux from the nulled ports significantly increases the overall throughput of the instrument. We show using synthetically generated data that the PLN detects exoplanets more effectively than the VFN. Furthermore, with the PLN, the exoplanet can be partially localized, and its flux ratio constrained. The PLN has the potential to be a powerful characterization tool complementary to traditional coronagraphs in future high-contrast instruments.

astro-ph.IM↗

arXiv2022

Controlling petals using fringes: discontinuous wavefront sensing through sparse aperture interferometry at Subaru/SCExAO

Low wind and petaling effects, caused by the discontinuous apertures of telescopes, are poorly corrected -- if at all -- by commonly used workhorse wavefront sensors (WFSs). Wavefront petaling breaks the coherence of the point spread function core, splitting it into several side lobes, dramatically shutting off scientific throughput. We demonstrate the re-purposing of non-redundant sparse aperture masking (SAM) interferometers into low-order WFSs complementing the high-order pyramid WFS, on the SCExAO experimental platform at Subaru Telescope. The SAM far-field interferograms formed from a 7-hole mask are used for direct retrieval of petaling aberrations, which are almost invisible to the main AO loop. We implement a visible light dual-band SAM mode, using two disjoint 25 nm wide channels, that we recombine to overcome the one-lambda ambiguity of fringe-tracking techniques. This enables a control over petaling with sufficient capture range yet without conflicting with coronagraphic modes in the near-infrared. We present on-sky engineering results demonstrating that the design is able to measure petaling well beyond the range of a single-wavelength equivalent design.

astro-ph.IM↗

arXiv2022

Focal-plane wavefront sensing with photonic lanterns I: theoretical framework

The photonic lantern (PL) is a tapered waveguide that can efficiently couple light into multiple single-mode optical fibers. Such devices are currently being considered for a number of tasks, including the coupling of telescopes and high-resolution, fiber-fed spectrometers, coherent detection, nulling interferometry, and vortex-fiber nulling (VFN). In conjunction with these use cases, PLs can simultaneously perform low-order focal-plane wavefront sensing. In this work, we provide a mathematical framework for the analysis of the photonic lantern wavefront sensor (PLWFS), deriving linear and higher-order reconstruction models as well as metrics through which sensing performance -- both in the linear and nonlinear regimes -- can be quantified. This framework can be extended to account for additional optics such as beam-shaping optics and vortex masks, and is generalizable to other wavefront sensing architectures. Lastly, we provide initial numerical verification of our mathematical models, by simulating a 6-port PLWFS. In a companion paper, we provide a more comprehensive numerical characterization of few-port PLWFSs, and consider how the sensing properties of these devices can be controlled and optimized.

astro-ph.IM↗

arXiv2022

High Contrast Imaging at the Photon Noise Limit with WFS-based PSF Calibration

Speckle Noise is the dominant source of error in high contrast imaging with adaptive optics system. We discuss the potential for wavefront sensing telemetry to calibrate speckle noise with sufficient precision and accuracy so that it can be removed in post-processing of science images acquired by high contrast imaging instruments. In such a self-calibrating system, exoplanet detection would be limited by photon noise and be significantly more robust and efficient than in current systems. We show initial laboratory and on-sky tests, demonstrating over short timescale that residual speckle noise is indeed calibrated to an accuracy exceeding readout and photon noise in the high contrast region. We discuss immplications for the design of space and ground high-contrast imaging systems.

astro-ph.IM↗

arXiv2022

A Visible-light Lyot Coronagraph for SCExAO/VAMPIRES

We describe the design and initial results from a visible-light Lyot coronagraph for SCExAO/VAMPIRES. The coronagraph is comprised of four hard-edged, partially transmissive focal plane masks with inner working angles of 36 mas, 55 mas, 92 mas, and 129 mas, respectively. The Lyot stop is a reflective, undersized design with a geometric throughput of 65.7%. Our preliminary on-sky contrast is 1e-2 at 0.1" to 1e-4 at 0.75" for all mask sizes. The coronagraph was deployed in early 2022 and is available for open use.

astro-ph.IM↗

arXiv2022

Monitoring inner regions in the RY Tau jet

We present multi-epoch observations of the RY~Tau jet for H$α$ and [\ion{Fe}{2}] 1.644 \micron~emission lines obtained with Subaru/SCExAO+VAMPIRES, Gemini/NIFS, and Keck/OSIRIS in 2019--2021. These data show a series of four knots within 1$\arcsec$ consistent with the proper motion of $\sim$0\farcs3~yr$^{-1}$, analogous to the jets associated with another few active T-Tauri stars. However, the spatial intervals between the knots suggest the time intervals of the ejections of about 1.2, 0.7, and 0.7 years, significantly shorter than those estimated for the other stars. These H$α$ images contrast with the archival VLT/SPHERE/ZIMPOL observations from 2015, which showed only a single knot-like feature at $\sim0\farcs25$. The difference between the 2015 and 2019--2021 epochs suggests an irregular ejection interval within the six-year range. Such variations of the jet ejection may be related to a short-term ($<$1 year) variability of the mass accretion rate. We compared the peaks of the H$α$ emissions with the ZIMPOL data taken in 2015, showing the brighter profile at the base ($<0\farcs3$) than the 2020--2021 VAMPIRES profiles due to time-variable mass ejection rates or the heating-cooling balance in the jet. The observed jet knot structures may be alternatively attributed to stationary shocks, but a higher angular resolution is required to confirm its detailed origin.

astro-ph.SR↗

arXiv2022

Images of Embedded Jovian Planet Formation At A Wide Separation Around AB Aurigae

Direct images of protoplanets embedded in disks around infant stars provide the key to understanding the formation of gas giant planets like Jupiter. Using the Subaru Telescope and Hubble Space Telescope, we find evidence for a jovian protoplanet around AB Aurigae orbiting at a wide projected separation (93 au), likely responsible for multiple planet-induced features in the disk. Its emission is reproducible as reprocessed radiation from an embedded protoplanet. We also identify two structures located at 430-580 au that are candidate sites of planet formation. These data reveal planet formation in the embedded phase and a protoplanet discovery at wide, > 50 au separations characteristic of most imaged exoplanets. With at least one clump-like protoplanet and multiple spiral arms, the AB Aur system may also provide the evidence for a long-considered alternative to the canonical model for Jupiter's formation: disk (gravitational) instability.

astro-ph.EP↗

arXiv2021

High contrast imaging wavefront sensor referencing from coronagraphic images

A key challenge of high contrast imaging (HCI) is to differentiate a speckle from an exoplanet signal. The sources of speckles are a combination of atmospheric residuals and aberrations in the non-common path. Those non-common path aberrations (NCPA) are particularly challenging to compensate for as they are not directly measured, and because they include static, quasi-static and dynamic components. The proposed method directly addresses the challenge of compensating the NCPA. The algorithm DrWHO - Direct Reinforcement Wavefront Heuristic Optimisation - is a quasi-real-time compensation of static and dynamic NCPA for boosting image contrast. It is an image-based lucky imaging approach, aimed at finding and continuously updating the ideal reference of the wavefront sensor (WFS) that includes the NCPA, and updating this new reference to the WFS. Doing so changes the point of convergence of the AO loop. We show here the first results of a post-coronagraphic application of DrWHO. DrWHO does not rely on any model nor requires accurate wavefront sensor calibration, and is applicable to non-linear wavefront sensing situations. We present on-sky performances using a pyramid WFS sensor with the Subaru coronagraph extreme AO (SCExAO) instrument.

astro-ph.IM↗

arXiv2021

On-sky validation of image-based adaptive optics wavefront sensor referencing

Differentiating between an exoplanet signal and residual speckle noise is a key challenge in high-contrast imaging. Speckles are due to a combination of fast, slow and static wavefront aberrations introduced by atmospheric turbulence and instrument optics. While wavefront control techniques developed over the last decade have shown promise in minimizing fast atmospheric residuals, slow and static aberrations such as non-common path aberrations (NCPAs) remain a key limiting factor for exoplanet detection. NCPA are not seen by the wavefront sensor (WFS) of the adaptive optics (AO) loop, hence the difficulty in correcting them. We propose to improve the identification and rejection of those aberrations. The algorithm DrWHO, performs frequent compensation of static and quasi-static aberrations to boost image contrast. By changing the WFS reference at every iteration of the algorithm, DrWHO changes the AO point of convergence to lead it towards a compensation of the static and slow aberrations. References are calculated using an iterative lucky-imaging approach, where each iteration updates the WFS reference, ultimately favoring high-quality focal plane images. We validate this concept through numerical simulations and on-sky testing on the SCExAO instrument at the 8.2-m Subaru telescope. Simulations show a rapid convergence towards the correction of 82% of the NCPAs. On-sky tests are performed over a 10-minute run in the visible (750 nm). We introduce a flux concentration (FC) metric to quantify the point spread function (PSF) quality and measure a 15.7% improvement. The DrWHO algorithm is a robust focal-plane wavefront sensing calibration method that has been successfully demonstrated on sky. It does not rely on a model nor requires wavefront sensor calibration or linearity. It is compatible with different wavefront control methods, and can be further optimized for speed and efficiency.

astro-ph.IM↗

arXiv2021

High contrast imaging at the photon noise limit with self-calibrating WFS/C systems

High contrast imaging (HCI) systems rely on active wavefront control (WFC) to deliver deep raw contrast in the focal plane, and on calibration techniques to further enhance contrast by identifying planet light within the residual speckle halo. Both functions can be combined in an HCI system and we discuss a path toward designing HCI systems capable of calibrating residual starlight at the fundamental contrast limit imposed by photon noise. We highlight the value of deploying multiple high-efficiency wavefront sensors (WFSs) covering a wide spectral range and spanning multiple optical locations. We show how their combined information can be leveraged to simultaneously improve WFS sensitivity and residual starlight calibration, ideally making it impossible for an image plane speckle to hide from WFS telemetry. We demonstrate residual starlight calibration in the laboratory and on-sky, using both a coronagraphic setup, and a nulling spectro-interferometer. In both case, we show that bright starlight can calibrate residual starlight.

astro-ph.IM↗

arXiv2021

SCExAO, a testbed for developing high-contrast imaging technologies for ELTs

To directly detect exoplanets and protoplanetary disks, the development of high accuracy wavefront sensing and control (WFS&C) technologies is essential, especially for ground-based Extremely Large Telescopes (ELTs). The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is a high-contrast imaging platform to discover and characterize exoplanets and protoplanetary disks. It also serves as a testbed to validate and deploy new concepts or algorithms for high-contrast imaging approaches for ELTs, using the latest hardware and software technologies on an 8-meter class telescope. SCExAO is a multi-band instrument, using light from 600 to 2500 nm, and delivering a high Strehl ratio (>80% in median seeing in H-band) downstream of a low-order correction provided by the facility AO188. Science observations are performed with coronagraphs, an integral field spectrograph, or single aperture interferometers. The SCExAO project continuously reaches out to the community for development and upgrades. Existing operating testbeds such as the SCExAO are also unique opportunities to test and deploy the new technologies for future ELTs. We present and show a live demonstration of the SCExAO capabilities (Real-time predictive AO control, Focal plane WFS&C, etc) as a host testbed for the remote collaborators to test and deploy the new WFS&C concepts or algorithms. We also present several high-contrast imaging technologies that are under development or that have already been demonstrated on-sky.

astro-ph.IM↗

arXiv2021

Full characterization of the instrumental polarization effects of the spectropolarimetric mode of SCExAO-CHARIS

SCExAO at the Subaru telescope is a visible and near-infrared high-contrast imaging instrument employing extreme adaptive optics and coronagraphy. The instrument feeds the near-infrared light (JHK) to the integral-field spectrograph CHARIS. The spectropolarimetric capability of CHARIS is enabled by a Wollaston prism and is unique among high-contrast imagers. We present a detailed Mueller matrix model describing the instrumental polarization effects of the complete optical path, thus the telescope and instrument. From measurements with the internal light source, we find that the image derotator (K-mirror) produces strongly wavelength-dependent crosstalk, in the worst case converting ~95% of the incident linear polarization to circularly polarized light that cannot be measured. Observations of an unpolarized star show that the magnitude of the instrumental polarization of the telescope varies with wavelength between 0.5% and 1%, and that its angle is exactly equal to the altitude angle of the telescope. Using physical models of the fold mirror of the telescope, the half-wave plate, and the derotator, we simultaneously fit the instrumental polarization effects in the 22 wavelength bins. Over the full wavelength range, our model currently reaches a total polarimetric accuracy between 0.08% and 0.24% in the degree of linear polarization. We propose additional calibration measurements to improve the polarimetric accuracy to <0.1% and plan to integrate the complete Mueller matrix model into the existing CHARIS post-processing pipeline. Our calibrations of CHARIS' spectropolarimetric mode will enable unique quantitative polarimetric studies of circumstellar disks and planetary and brown dwarf companions.

astro-ph.IM↗

arXiv2021

Phase Retrieval and Design with Automatic Differentiation

The principal limitation in many areas of astronomy, especially for directly imaging exoplanets, arises from instability in the point spread function (PSF) delivered by the telescope and instrument. To understand the transfer function, it is often necessary to infer a set of optical aberrations given only the intensity distribution on the sensor - the problem of phase retrieval. This can be important for post-processing of existing data, or for the design of optical phase masks to engineer PSFs optimized to achieve high contrast, angular resolution, or astrometric stability. By exploiting newly efficient and flexible technology for automatic differentiation, which in recent years has undergone rapid development driven by machine learning, we can perform both phase retrieval and design in a way that is systematic, user-friendly, fast, and effective. By using modern gradient descent techniques, this converges efficiently and is easily extended to incorporate constraints and regularization. We illustrate the wide-ranging potential for this approach using our new package, Morphine. Challenging applications performed with this code include precise phase retrieval for both discrete and continuous phase distributions, even where information has been censored such as heavily-saturated sensor data. We also show that the same algorithms can optimize continuous or binary phase masks that are competitive with existing best solutions for two example problems: an Apodizing Phase Plate (APP) coronagraph for exoplanet direct imaging, and a diffractive pupil for narrow-angle astrometry. The Morphine source code and examples are available open-source, with a similar interface to the popular physical optics package Poppy.

astro-ph.IM↗

arXiv2021

3D-M3: High-spatial resolution spectroscopy with extreme AO and 3D printed micro-lenslets

By combining IFS with ExAO we are now able to resolve objects close to the diffraction-limit of large telescopes, exploring new science cases. We introduce an IFU designed to couple light with a minimal platescale from the SCExAO facility at NIR wavelengths to a SM spectrograph. The IFU has a 3D-printed MLA on top of a custom SM MCF, to optimize the coupling of light into the fiber cores. We demonstrate the potential of the instrument via initial results from the first on-sky runs at the 8.2 m Subaru Telescope with a spectrograph using off-the-shelf optics, allowing for rapid development with low cost.

astro-ph.IM↗

arXiv2021

Achromatic photonic tricouplers for application in nulling interferometry

Integrated-optic components are being increasingly used in astrophysics, mainly where accuracy and precision are paramount. One such emerging technology is nulling interferometry that targets high contrast and high angular resolution. Two of the most critical limitations encountered by nullers are rapid phase fluctuations in the incoming light causing instability in the interference and chromaticity of the directional couplers that prevent a deep broadband interferometric null. We explore the use of a tricoupler designed by ultrafast laser inscription that solves both issues. Simulations of a tricoupler, incorporated into a nuller, result in order of a magnitude improvement in null depth.

astro-ph.IM↗

arXiv2021

First light of a holographic aperture mask: Observation at the Keck OSIRIS Imager

We report on the design, construction, and commissioning of a prototype aperture masking technology implemented at the Keck OSIRIS Imager: the holographic aperture mask. Holographic aperture masking (HAM) aims at (i) increasing the throughput of sparse aperture masking (SAM) by selectively combining all subapertures across a telescope pupil in multiple interferograms using a phase mask, and (ii) adding low-resolution spectroscopic capabilities. Using liquid-crystal geometric phase patterns, we manufacture a HAM mask that uses an 11-hole SAM design as the central component and a holographic component comprising 19 different subapertures. Thanks to a multilayer liquid-crystal implementation, the mask has a diffraction efficiency higher than 96% from 1.1 to 2.5 micron. We create a pipeline that extracts monochromatic closure phases from the central component as well as multiwavelength closure phases from the holographic component. We test the performance of the HAM mask in the laboratory and on-sky. The holographic component yields 26 closure phases with spectral resolutions between R$\sim$6.5 and R$\sim$15. On April 19, 2019, we observed the binary star HDS 1507 in the Hbb filter ($λ_0 = 1638$ nm and $Δλ= 330$ nm) and retrieved a constant separation of 120.9 $\pm 0.5$ mas for the independent wavelength bins, which is in excellent agreement with literature values. For both the laboratory measurements and the observations of unresolved reference stars, we recorded nonzero closure phases -- a potential source of systematic error that we traced to polarization leakage of the HAM optic. We propose a future upgrade that improves the performance, reducing this effect to an acceptable level. Holographic aperture masking is a simple upgrade of SAM with increased throughput and a new capability of simultaneous low-resolution spectroscopy that provides new differential observables.

astro-ph.IM↗

arXiv2021

An innovative integral field unit upgrade with 3D-printed micro-lenses for the RHEA at Subaru

In the new era of Extremely Large Telescopes (ELTs) currently under construction, challenging requirements drive spectrograph designs towards techniques that efficiently use a facility's light collection power. Operating in the single-mode (SM) regime, close to the diffraction limit, reduces the footprint of the instrument compared to a conventional high-resolving power spectrograph. The custom built injection fiber system with 3D-printed micro-lenses on top of it for the replicable high-resolution exoplanet and asteroseismology spectrograph at Subaru in combination with extreme adaptive optics of SCExAO, proved its high efficiency in a lab environment, manifesting up to ~77% of the theoretical predicted performance.

astro-ph.IM↗