arXiv subjects

Behrouz Farhang-Boroujeny

Publications and source records attributed to Behrouz Farhang-Boroujeny.

At least 19 recordsLinked to original sources

arXiv2025

Packet Detection in a Filter Bank-Based Ultra-Wideband Communication System

Recently, filter bank multi-carrier spread spectrum (FBMC-SS) technology has been proposed for use in ultra-wideband (UWB) communication systems. It has been noted that, due to the spectral partitioning properties of the filter banks, a UWB signal can be synthesized and processed using a parallel set of signal processors operating at a moderate rate. This transceiver architecture can be used to generate UWB signals, without requiring a high-rate analog-to-digital and/or digital-to-analog converter. In this paper, beginning with a design operating on a single signal processor, we explore the development of a packet detector using the Rao score test. Taking advantage of the FBMC-SS signal structure, an effective detector design based on a cascade channelizer is proposed. We refer to this design as singe-radio band (SRB) detector. Given the typical bandwidth of UWB systems ($\bf 500$~MHz or wider), the SRB detector has to operate at a fast sampling rate of greater than $\bf 500$~MHz. This may be undesirable, as low cost analog-to-digital (ADC) and digital-to-analog (DAC) converters are often limited to a sampling rate of $\bf 200$~MHz or lower. Taking note of this point, the proposed SRB detector is extended to a multi-radio band (MRB) detector, where a set of parallel signal processors operating at a moderate sampling rate are used for a more practical implementation of the detector. Through computer simulations, we show that SRB and MRB detectors have the same performance in typical UWB channels. Finally, we provide results from an over-the-air demonstration of a UWB design occupying $\bf 1.28$~GHz of bandwidth. We find that reliable detection performance is possible in the harshest environments, at signal-to-noise ratios as low as $\bf -40$~dB with a preamble length of approximately half the duration of longest preamble length recommended in the IEEE802.15.4 standard.

eess.SP↗

arXiv2025

Ultra-Wideband Communications: Interference Challenges and Solutions

The idea of ultra-wideband (UWB) communications for short ranges (up to a few tens of meters) has been around for nearly three decades. However, despite significant efforts by the industry, UWB deployment has not yet reached its predicted potential. This article, thus, seeks to rectify this situation by providing a practical examination of UWB interference conditions. Through a spectrum survey of today's wireless environments, we explore the interference that UWB devices may face from a perspective of outage probability in both high- and low-rate configurations. We find that by suppressing interference, the outage probability can be reduced by one or more orders of magnitude. In the non-line-of sight channels, in particular, we find that both interference suppression and bandwidth expansion are required to support the minimum data rates suggested in the IEEE802.15.4 series of standards. We connect these findings to a recently proposed UWB signaling method based on filter banks and show this method fulfills the above requirements for implementing effective UWB systems.

eess.SP↗

arXiv2025

Theoretical Analysis of Multi-coding with Arbitrary Correlations Among the Codes

The use of non-orthogonal signals has several benefits over orthogonal signals in multi-coded communications. We provide a novel, theoretical study of non-orthogonal signaling to expand the applicability of these schemes. Motivated by a class of multi-carrier spread spectrum systems, this paper presents a thorough symbol error rate analysis of the broad class of multi-code signaling methods when they make use of codes which are not necessarily orthogonal. Our analysis is also extended to the case where the code set includes the negative of each code vector, i.e., an extension to biorthogonal signaling. Moreover, it is shown that the symbol error rate results derived in this paper reduce to those available in the literature when the multi-codes are orthogonal or have equal correlation between vectors. Additionally, we show how Monte Carlo integration can be used to evaluate the integrals in the error probability calculation and derive low complexity upper bounds on the error probabilities. We show that by combining these techniques, the error probability can be efficiently computed across the full SNR regime. Finally, we use the upper bound of the error probability to develop some analytical insights about the impacts of non-orthogonality among the code vectors on the symbol error probability.

cs.IT↗

arXiv2025

Filter-Banks for Ultra-Wideband for Communications, Sensing, and Localization

Recently, filter-bank multicarrier spread spectrum (FBMC-SS) has been proposed as a candidate waveform for ultra-wideband (UWB) communications, sensing, and localization. It has been noted that FBMC-SS is a perfect match to this application, leading to a trivial method of matching to the required spectral mask at different regions of the world. FBMC-SS also allows easy rejection of high-power interfering signals that may appear over different parts of the UWB spectral band. Moreover, passing the received signal through a matched filter provides precise information for sensing and localization. In this paper, we concentrate on the use of staggered multitone spread spectrum (SMT-SS) for UWB communications. SMT makes use of offset quadrature amplitude modulation (OQAM) to transmit data symbols over overlapping subcarrier bands. This form of FBMC-SS is well-suited to UWB communications because it has good spectral efficiency and a flat power spectral density (PSD), resulting in good utilization of the UWB spectral mask.

eess.SP↗

arXiv2025

Filtered Multi-Tone Spread Spectrum with Overlapping Subbands

A new form of the filter bank multi-carrier spread spectrum (FBMC-SS) waveform is presented. This new waveform modifies the filtered multi-tone spread spectrum (FMT-SS) system, and is intended to whiten the power spectral density (PSD) of the transmit signal. In the conventional FMT-SS, subcarrier bands are non-overlapping, leaving a spectral null between the adjacent subcarrier bands. To make FMT-SS more appealing for a broader set of applications than those studied in the past, we propose adding additional subcarriers centered at these nulls and thoroughly explore the impact of the added subcarriers on the system performance. This modified form of FMT-SS is referred to as overlapped FMT-SS (OFMT-SS). We explore the conditions required for maximally flattening the PSD of the synthesized OFMT-SS signal and for cancelling the interference caused by overlapping subbands. We also explore the choices of spreading gains that result in a low peak-to-average power ratio (PAPR) for a number of different scenarios. Further reduction of the PAPR of the synthesized signal through clipping methods is also explored. Additionally, we propose methods of multi-coding for increasing the data rate of the OFMT-SS waveform, while minimally impacting its PAPR.

eess.SP↗

arXiv2024

Multicarrier Spread Spectrum Communications with Noncontiguous Subcarrier Bands for HF Skywave Links

Growing traffic over the high-frequency (HF) band poses significant challenges to establishing robust communication links. While existing spread-spectrum HF transceivers are, to some degree, robust against harsh HF channel conditions, their performance significantly degrades in the presence of strong co-channel interference. To improve performance in congested channel conditions, we propose a filter-bank based multicarrier spread-spectrum waveform with noncontiguous subcarrier bands. The use of noncontiguous subcarriers allows the system to at once leverage the robustness of a wideband system while retaining the frequency agility of a narrowband system. In this study, we explore differences between contiguous and noncontiguous systems by considering their respective peak-to-average power ratios (PAPRs) and matched-filter responses. Additionally, we develop a modified filter-bank receiver structure to facilitate both efficient signal processing and noncontiguous channel estimation. We conclude by presenting simulated and over-the-air results of the noncontiguous waveform, demonstrating both its robustness in harsh HF channels and its enhanced performance in congested spectral conditions.

eess.SP↗

arXiv2023

Downlink Transmission in FBMC-based Massive MIMO with Co-located and Distributed Antennas

This paper introduces a practical precoding method for the downlink of Filter Bank Multicarrier-based (FBMC-based) massive multiple-input multiple-output (MIMO) systems. The proposed method comprises a two-stage precoder, consisting of a fractionally spaced prefilter (FSP) per subcarrier to equalize the channel across each subcarrier band. This is followed by a conventional precoder that concentrates the signals of different users at their spatial locations, ensuring each user receives only the intended information. In practical scenarios, a perfect channel reciprocity may not hold due to radio chain mismatches in the uplink and downlink. Moreover, the channel state information (CSI) may not be perfectly known at the base station. To address these issues, we theoretically analyze the performance of the proposed precoder in presence of imperfect CSI and channel reciprocity calibration errors. Our investigation covers both co-located (cell-based) and cell-free massive MIMO cases. In the cell-free massive MIMO setup, we propose an access point selection method based on the received SINRs of different users in the uplink. Finally, we conduct numerical evaluations to assess the performance of the proposed precoder. Our results demonstrate the excellent performance of the proposed precoder when compared with the orthogonal frequency division multiplexing (OFDM) method as a benchmark.

eess.SP↗

arXiv2022

Resource Allocation for Single Carrier Massive MIMO Systems

Resource allocation in orthogonal frequency division multiplexing (OFDM) systems is performed through allocating blocks of subcarriers to each user. Even though OFDM is the primary waveform for 5G NR systems, research reports have noted that single carrier modulation (SCM) offers several advantages over OFDM in massive multiple input multiple output (MIMO) systems, making it a preferred candidate for some future applications such as massive machine type communications (mMTC). This paper presents a method for SCM resource allocation and the relevant information recovery algorithms at the receiver. Our emphasis is on cyclic prefixed SCM, where highly flexible and efficient frequency domain detection algorithms enable the operation of many simultaneous users in a massive MIMO uplink scenario. The proposed resource allocation method allows the number of users to exceed the number of antennas at the base station (BS). Each single carrier transmission is partitioned into $L$ interleaved streams, and each user is allocated a number of such streams. One major benefit of SCM is that each data symbol is spread over the entire bandwidth. As such, the receiver performance is dictated by the average channel gain across the transmission band rather than the channel gain at a given frequency bin or a small group of frequencies. In the proposed setup, each stream may be thought of as a resource block in SCM, analogous to resource blocks in OFDM. Hence, in the context of this paper, the terms resource blocks and streams may be used interchangeably.

eess.SP↗

arXiv2022

Downlink Precoding for FBMC-based Massive MIMO with Imperfect Channel Reciprocity

In this paper, a practical precoding method for the downlink of filter bank multicarrier-based (FBMC-based) massive multiple-input multiple-output (MIMO) is developed. The proposed method includes a two-stage precoder consisting of a fractionally spaced prefilter (FSP) per subcarrier for flattening/equalizing the channel across the subcarrier band, followed by a conventional precoder whose goal is to concentrate the signals of different users at their spatial locations. This way, each user receives only the intended information. In this paper, we take note that channel reciprocity may not hold perfectly in practical scenarios due to the mismatch of radio chains in uplink and downlink. Additionally, channel state information (CSI) at the base station may not be perfectly known. This, together with imperfect channel reciprocity can lead to detrimental effects on the downlink precoder performance. We theoretically analyze the performance of the proposed precoder in the presence of imperfect CSI and channel reciprocity calibration errors. This leads to an effective method for compensating these effects. Finally, we numerically evaluate the performance of the proposed precoder. Our results show that the proposed precoder leads to an excellent performance when benchmarked against OFDM.

eess.SP↗

arXiv2021

FBMC Receiver Design and Analysis for Medium and Large Scale Antenna Systems

In this paper, we design receivers for filter bank multicarrier-based (FBMC-based) massive MIMO considering practical aspects such as channel estimation and equalization. In particular, we propose a spectrally efficient pilot structure and a channel estimation technique in the uplink to jointly estimate all the users' channel impulse responses. We mathematically analyze our proposed channel estimator and find the statistics of the channel estimation errors. These statistics are incorporated into our proposed equalizers to deal with the imperfect channel state information (CSI) effect. We revisit the channel equalization problem for FBMC-based massive MIMO, address the shortcomings of the existing equalizers in the literature, and make them more applicable to practical scenarios. The proposed receiver in this paper consists of two stages. In the first stage, a linear combining of the received signals at the base station (BS) antennas provides a coarse channel equalization and removes any multiuser interference. In the second stage, a per subcarrier fractionally spaced equalizer (FSE) takes care of any residual distortion of the channel for the user of interest. We propose an FSE design based on the equivalent channel at the linear combiner output. This enables the applicability of our proposed technique to small and/or distributed antenna setups such as cell-free massive MIMO. Finally, the efficacy of the proposed techniques is corroborated through numerical analysis.

eess.SP↗

arXiv2021

Efficient Precoding for Single Carrier Modulation in Multi-User Massive MIMO Networks

By processing in the frequency domain (FD), massive MIMO systems can approach the theoretical per-user capacity using a single carrier modulation (SCM) waveform with a cyclic prefix. Minimum mean squared error (MMSE) detection and zero forcing (ZF) precoding have been shown to effectively cancel multi-user interference while compensating for inter-symbol interference. In this paper, we present a modified downlink precoding approach in the FD based on regularized zero forcing (RZF), which reuses the matrix inverses calculated as part of the FD MMSE uplink detection. By reusing these calculations, the computational complexity of the RZF precoder is drastically lowered, compared to the ZF precoder. Introduction of the regularization in RZF leads to a bias in the detected data symbols at the user terminals. We show this bias can be removed by incorporating a scaling factor at the receiver. Furthermore, it is noted that user powers have to be optimized to strike a balance between noise and interference seen at each user terminal. The resulting performance of the RZF precoder exceeds that of the ZF precoder for low and moderate input signal-to-noise ratio (SNR) conditions, and performance is equal for high input SNR. These results are established and confirmed by analysis and simulation.

eess.SP↗

arXiv2020

Frequency Domain Multi-user Detection for Single Carrier Modulation with Cyclic Prefix

Frequency domain (FD) multi-user detection (MUD) has been shown to be an effective means of approaching the theoretical per-user capacity for single carrier modulation (SCM) schemes in massive MIMO scenarios with highly dispersive channels. When a cyclic prefix is added to the SCM waveform, the circulant structures of the resulting convolutional channel matrix allows for relatively simple expressions for the FD detection. In this paper, we develop a computationally efficient minimum mean squared error (MMSE) FD-MUD technique in a time-division duplexing (TDD) massive MIMO setup and show how processing steps can be shared between uplink and downlink.

eess.SP↗

arXiv2020

Cyclic Prefix Direct Sequence Spread Spectrum Capacity Analysis

Cyclic Prefix Direct Sequence Spread Spectrum (CP-DSSS) is a novel waveform that is proposed as a solution to massive machine type communications (mMTC) for 5G and beyond. This paper analyzes the capacity of CP-DSSS in comparison with Orthogonal Frequency-Division Multiplexing (OFDM). We show that CP-DSSS achieves the same capacity as OFDM and can be optimized with similar precoding methods (e.g., water-filling). Because of its spread spectrum nature, CP-DSSS can operate as secondary network using the same spectrum as the primary 4G or 5G network, but transmitting at much lower power. Accordingly, the combination of primary and secondary signals in the envisioned setup may be viewed as a power NOMA (non-orthogonal multiple access) technique where primary signals are detected and subtracted from the received signal first before detecting the secondary signals. In order to operate at a sufficiently low interference level to the primary network, details of CP-DSSS capacity for symbol rate reduction and multi-antenna operation are developed. The capacity limits established in this paper can be used as a baseline to evaluate the performance of future CP-DSSS receiver architectures for single- and multi-user scenarios.

eess.SP↗

arXiv2020

Multi-user Capacity of Cyclic Prefix Direct Sequence Spread Spectrum with Linear Detection and Precoding

Cyclic Prefix Direct Sequence Spread Spectrum (CP-DSSS) is a promising solution for futuristic 6G ultra-reliable low latency communications (URLLC) and massive machine type communication (mMTC) applications. We propose that in such applications, the CP-DSSS waveform would operate as a secondary network at the same frequencies as the primary network but at much lower SNR. In this paper, we evaluate per-user capacity of CP-DSSS when simple matched filtering (MF) is performed on the uplink (UL) and time-reversal (TR) precoding is used on the downlink (DL). In this setting when operating in the low SNR regime, CP-DSSS achieves a per-user capacity that is near the optimum single-user capacity. TR precoding converges to the optimal capacity as the number of antennas at the hub/gateway increases. Using the estimated channel impulse response for MF and TR introduces little to no capacity loss. Given the near-optimal performance of MF detection and TR precoding for each of the users, CP-DSSS can be implemented with simple device transceiver structures, reducing per-unit cost for massively deployed 6G networks.

eess.SP↗

arXiv2020

Spectrally Efficient Pilot Structure and Channel Estimation for Multiuser FBMC Systems

In this paper, we consider channel estimation problem in the uplink of filter bank multicarrier (FBMC) systems. We propose a pilot structure and a joint multiuser channel estimation method for FBMC. Opposed to the available solutions in the literature, our proposed technique does not rely on the flat-channel condition over each subcarrier band or any requirement for placing guard symbols between different users' pilots. Our proposed pilot structure reduces the training overhead by interleaving the users' pilots in time and frequency. Thus, we can accommodate a larger number of training signals within the same bandwidth and improve the spectral efficiency. Furthermore, this pilot structure inherently leads to a reduced peak-to-average power ratio (PAPR) compared with the solutions that use all the subcarriers for training. We analytically derive the Cramer-Rao lower bound (CRLB) and mean square error (MSE) expressions for our proposed method. We show that these expressions are the same. This confirms the optimality of our proposed method, which is numerically evaluated through simulations. Relying on its improved spectral efficiency, our proposed method can serve a large number of users and relax pilot contamination problem in FBMC-based massive MIMO systems. This is corroborated through simulations in terms of sum-rate performance for both single cell and multicell scenarios.

eess.SP↗

arXiv2018

Filter Bank Multicarrier in Massive MIMO: Analysis and Channel Equalization

We perform an asymptotic study of the performance of filter bank multicarrier (FBMC) in the context of massive multi-input multi-output (MIMO). We show that the effects of channel distortions, i.e., intersymbol interference and intercarrier interference, do not vanish as the base station (BS) array size increases. As a result, the signal-to-interference-plus-noise ratio (SINR) cannot grow unboundedly by increasing the number of BS antennas, and is upper bounded by a certain deterministic value. We show that this phenomenon is a result of the correlation between the multi-antenna combining tap values and the channel impulse responses between the mobile terminals and the BS antennas. To resolve this problem, we introduce an efficient equalization method that removes this correlation, enabling us to achieve arbitrarily large SINR values by increasing the number of BS antennas. We perform a thorough analysis of the proposed system and find analytical expressions for both equalizer coefficients and the respective SINR.

cs.IT↗

arXiv2018

Underlay Control Signaling for Ultra-Reliable Low-Latency IoT Communications

Future mobile networks not only envision enhancing the traditional link quality and data rates of mobile broad band (MBB) links, but also development of new control channels to meet the requirements of delay sensitive use cases. In particular, the need for ultra-reliable low-latency communications (URLLC) for many internet of things (IoT) users is greatly emphasized. In this paper, we present a novel spread spectrum waveform design that we propose for transmission of control signals to establish URLLC communications. These control signals are transmitted over the spectral resources that belong to the MBB communications in the network, but at a level that minimally affects these data channels. The proposed waveform, although a direct sequence spread spectrum (DSSS) technique, is designed to take advantage of symbol synchronization available to the OFDM broad band communications in the network. This, clearly, allows simple synchronization with the rest of the network. The proposed DSSS method can transmit single and multiple bits within each OFDM time frame and can serve many user equipment (UE) nodes simultaneously.

eess.SP↗

arXiv2017

OFDM Without CP in Massive MIMO

We study the possibility of removing the cyclic prefix (CP) overhead from orthogonal frequency division multiplexing (OFDM) in massive multiple-input multiple-output (MIMO) systems. We consider the uplink transmission while our results are applicable to the downlink as well. The absence of CP increases the spectral efficiency in expense of intersymbol interference (ISI) and intercarrier interference (ICI). It is known that in massive MIMO, the effects of uncorrelated noise and multiuser interference vanish as the number of base station (BS) antennas tends to infinity. To investigate if the channel distortions in the absence of CP fade away, we study the performance of the standard maximum ratio combining (MRC) receiver. Our analysis reveals that in this receiver, there always remains some residual interference leading to saturation of signal-to-interference-plus-noise ratio (SINR). To resolve this problem, we propose to use the time reversal (TR) technique. Moreover, in order to further reduce the multiuser interference, we propose a zero-forcing equalization to be deployed after the TR combining. We compare the achievable rate of the proposed system with that of the conventional CP-OFDM. We show that in realistic channels, a higher spectral efficiency is achieved by removing the CP from OFDM, while reducing the computational complexity.

cs.IT↗