arXiv subjects

Boris Desiatov

Publications and source records attributed to Boris Desiatov.

At least 19 recordsLinked to original sources

arXiv2026

Dielectric-loaded guided-wave electro-optic modulator using bulk rubidium titanyl phosphate

Rubidium titanyl phosphate (RTP) is widely used in bulk Pockels cells because it combines a useful linear electro-optic response with low dielectric permittivity, high electrical resistivity, negligible piezoelectric ringing, and high optical-damage tolerance. Its use in integrated or guided-wave modulators has been limited by the absence of a mature thin-film RTP platform. Here we propose a dielectric-loaded guided-wave modulator in which a silicon nitride strip on an unetched bulk RTP crystal forms a near-surface optical mode that overlaps with side-electrode fields. The analysis focuses on full-vector optical modes, GSG electrostatic and RF response, tensor-aware electro-optic coupling, and device-level performance at 1064~nm.

physics.optics↗

arXiv2026

Numerical Investigation of a 3D End-Firing Antenna Array Based on Two-Photon Polymerization on Thin-Film Lithium Niobate for Optical Beam Steering

Optical phased arrays (OPAs) are key components for solid-state beam steering in emerging photonic technologies such as LiDAR, optical communication, and adaptive optics. However, conventional integrated OPA designs face trade-offs between bandwidth, steering range, and fabrication complexity. Here we designed and numerically analyzed a novel three-dimensional end-firing antenna array compatible with fabrication using two-photon polymerization (2PP) directly on a thin-film lithium niobate (TFLN) platform. By elevating the polymer antennas above the chip surface, the design enables two-dimensional beam steering while maintaining the broadband advantages of end-fire emission. Full-wave electromagnetic simulations demonstrate transmission efficiencies up to 89.5\% over the \SIrange{1.4}{1.6}{\micro\meter} wavelength range, achieving a field of view of \ang{24.9} $\times$ \ang{22.8} with beamwidths of approximately \ang{1.7}. The architecture's compatibility with electro-optic phase control and advanced array configurations suggests significant potential for high-speed, low-loss beam steering systems. This work establishes a foundation for scalable 3D photonic phased arrays that bridge integrated optics with free-space beam manipulation.

physics.optics↗

arXiv2024

Wavelength-accurate and wafer-scale process for nonlinear frequency mixers in thin-film lithium niobate

Recent advancements in thin-film lithium niobate (TFLN) photonics have led to a new generation of high-performance electro-optic devices, including modulators, frequency combs, and microwave-to-optical transducers. However, the broader adoption of TFLN-based devices that rely on all-optical nonlinearities have been limited by the sensitivity of quasi-phase matching (QPM), realized via ferroelectric poling, to fabrication tolerances. Here, we propose a scalable fabrication process aimed at improving the wavelength-accuracy of optical frequency mixers in TFLN. In contrast to the conventional pole-before-etch approach, we first define the waveguide in TFLN and then perform ferroelectric poling. This sequence allows for precise metrology before and after waveguide definition to fully capture the geometry imperfections. Systematic errors can also be calibrated by measuring a subset of devices to fine-tune the QPM design for remaining devices on the wafer. Using this method, we fabricated a large number of second harmonic generation devices aimed at generating 737 nm light, with 73% operating within 5 nm of the target wavelength. Furthermore, we also demonstrate thermo-optic tuning and trimming of the devices via cladding deposition, with the former bringing ~96% of tested devices to the target wavelength. Our technique enables the rapid growth of integrated quantum frequency converters, photon pair sources, and optical parametric amplifiers, thus facilitating the integration of TFLN-based nonlinear frequency mixers into more complex and functional photonic systems.

physics.app-ph↗

arXiv2024

Supercontinuum Generation by Saturated Second-Order Nonlinear Interactions

We propose a new approach to supercontinuum generation and carrier-envelope-offset detection based on saturated second-order nonlinear interactions in dispersion-engineered nanowaveguides. The technique developed here broadens the interacting harmonics by forming stable bifurcations of the pulse envelopes due to an interplay between phase-mismatch and pump depletion. We first present an intuitive heuristic model for spectral broadening by second-harmonic generation of femtosecond pulses, and show that this model agrees well with experiments. Then, having established strong agreement between theory and experiment, we develop scaling laws that determine the energy required to generate an octave of bandwidth as a function of input pulse duration, device length, and input pulse chirp. These scaling laws suggest that future realization based on this approach could enable supercontinuum generation with orders of magnitude less energy than current state-of-the-art devices.

physics.optics↗

arXiv2022

Quasi-static Optical Parametric Amplification

High-gain optical parametric amplification is an important nonlinear process used both as a source of coherent infrared light and as a source of nonclassical light. In this work, we experimentally demonstrate an approach to optical parametric amplification that enables extremely large parametric gains with low energy requirements. In conventional nonlinear media driven by femtosecond pulses, multiple dispersion orders limit the effective interaction length available for parametric amplification. Here, we use the dispersion engineering available in periodically poled thin-film lithium niobate nanowaveguides to eliminate several dispersion orders at once. The result is a quasi-static process; the large peak intensity associated with a short pump pulse can provide gain to signal photons without undergoing pulse distortion or temporal walk-off. We characterize the parametric gain available in these waveguides using optical parametric generation, where vacuum fluctuations are amplified to macroscopic intensities. When driven with pulse energies in excess of 10 pJ, we observe saturated parametric gains as large as 88 dB (146 dB/cm). The devices shown here achieve saturated optical parametric generation with orders of magnitude less pulse energy than previous techniques.

physics.optics↗

arXiv2022

Reduced Material Loss in Thin-film Lithium Niobate Waveguides

Thin-film lithium niobate has shown promise for scalable applications ranging from single-photon sources to high-bandwidth data communication systems. Realization of the next generation high-performance classical and quantum devices, however, requires much lower optical losses than the current state of the art ($\sim$10 million). Unfortunately, material limitations of ion-sliced thin-film lithium niobate have not been explored, and therefore it is unclear how high-quality factor can be achieved in this platform. Here we evaluate the material limited quality factor of thin-film lithium niobate photonic platform can be as high as $Q\approx 1.8\times10^{8}$ at telecommunication wavelengths, corresponding to a propagation loss of 0.2 dB/m.

physics.optics↗

arXiv2021

Integrated photonics on thin-film lithium niobate

Lithium niobate (LN), an outstanding and versatile material, has influenced our daily life for decades: from enabling high-speed optical communications that form the backbone of the Internet to realizing radio-frequency filtering used in our cell phones. This half-century-old material is currently embracing a revolution in thin-film LN integrated photonics. The success of manufacturing wafer-scale, high-quality, thin films of LN on insulator (LNOI), accompanied with breakthroughs in nanofabrication techniques, have made high-performance integrated nanophotonic components possible. With rapid development in the past few years, some of these thin-film LN devices, such as optical modulators and nonlinear wavelength converters, have already outperformed their legacy counterparts realized in bulk LN crystals. Furthermore, the nanophotonic integration enabled ultra-low-loss resonators in LN, which unlocked many novel applications such as optical frequency combs and quantum transducers. In this Review, we cover -- from basic principles to the state of the art -- the diverse aspects of integrated thin-film LN photonics, including the materials, basic passive components, and various active devices based on electro-optics, all-optical nonlinearities, and acousto-optics. We also identify challenges that this platform is currently facing and point out future opportunities. The field of integrated LNOI photonics is advancing rapidly and poised to make critical impacts on a broad range of applications in communication, signal processing, and quantum information.

physics.optics↗

arXiv2020

On-chip self-referencing using integrated lithium niobate waveguides

The measurement and stabilization of the carrier-envelope offset frequency $f_{\textrm{CEO}}$ via self-referencing is paramount for optical frequency comb generation which has revolutionized precision frequency metrology, spectroscopy, and optical clocks. Over the past decade, the development of chip-scale platforms has enabled compact integrated waveguides for supercontinuum generation. However, there is a critical need for an on-chip self-referencing system that is adaptive to different pump wavelengths, requires low pulse energy, and does not require complicated processing. Here, we demonstrate efficient carrier-envelope offset frequency $f_{\textrm{CEO}}$ stabilization of a modelocked laser with only 107 pJ of pulse energy via self-referencing in an integrated lithium niobate waveguide. We realize an $f$-$2f$ interferometer through second-harmonic generation and subsequent supercontinuum generation in a single dispersion-engineered waveguide with a stabilization performance equivalent to a conventional off-chip module. The $f_{\textrm{CEO}}$ beatnote is measured over a pump wavelength range of 70 nm. We theoretically investigate our system using a single nonlinear envelope equation with contributions from both second- and third-order nonlinearities. Our modeling reveals rich ultrabroadband nonlinear dynamics and confirms that the initial second harmonic generation followed by supercontinuum generation with the remaining pump is responsible for the generation of a strong $f_{\textrm{CEO}}$ signal as compared to a traditional $f$-$2f$ interferometer. Our technology provides a highly-simplified system that is robust, low cost, and adaptable for precision metrology for use outside a research laboratory.

physics.optics↗

arXiv2019

Ultrabroadband Nonlinear Optics in Nanophotonic Periodically Poled Lithium Niobate Waveguides

Quasi-phasematched interactions in waveguides with quadratic nonlinearities enable highly efficient nonlinear frequency conversion. In this article, we demonstrate the first generation of devices that combine the dispersion-engineering available in nanophotonic waveguides with quasi-phasematched nonlinear interactions available in periodically poled lithium niobate (PPLN). This combination enables quasi-static interactions of femtosecond pulses, reducing the pulse energy requirements by several orders of magnitude, from picojoules to femtojoules. We experimentally demonstrate two effects associated with second harmonic generation. First, we observe efficient quasi-phasematched second harmonic generation with <100 fJ of pulse energy. Second, in the limit of strong phase-mismatch, we observe spectral broadening of both harmonics with as little as 2-pJ of pulse energy. These results lay a foundation for a new class of nonlinear devices, in which co-engineering of dispersion with quasi-phasematching enables efficient nonlinear optics at the femtojoule level.

physics.optics↗

arXiv2019

Silicon photodetector for integrated lithium niobate photonics

We demonstrate integration of an amorphous silicon photodetector with thin film lithium niobate photonic platform operating in the visible wavelength range. We present the details of the design, fabrication, integration and experimental characterization of this metal-semiconductor-metal photodetector that features responsivity of 22 mA/W to 37mA/W over the wide optical bandwidth spanning 635 nm to 850 nm wavelengths range.

physics.app-ph↗

arXiv2019

Supercontinuum generation in angle-etched diamond waveguides

We experimentally demonstrate on-chip supercontinuum generation in the visible region in angle etched diamond waveguides. We measure an output spectrum spanning 670 nm to 920 nm in a 5mm long waveguide using 100 fs pulses with 187 pJ of incident pulse energy. Our fabrication technique, combined with diamonds broad transparency window, offers a potential route toward broadband supercontinuum generation in the UV domain.

physics.optics↗

arXiv2019

Ultra-low loss integrated visible photonics using thin-film lithium niobate

Integrated photonics is a powerful platform that can improve the performance and stability of optical systems, while providing low-cost, small-footprint and scalable alternatives to implementations based on free-space optics. While great progress has been made on the development of low-loss integrated photonics platforms at telecom wavelengths, visible wavelength range has received less attention. Yet, many applications utilize visible or near-visible light, including those in optical imaging, optogenetics, and quantum science and technology. Here we demonstrate an ultra-low loss integrated visible photonics platform based on thin film lithium niobate on insulator. Our waveguides feature ultra-low propagation loss of 6 dB/m, while our microring resonators have an intrinsic quality factor of 11 million, both measured at 637 nm wavelength. Additionally, we demonstrate an on-chip visible intensity modulator with an electro-optic bandwidth of 10 GHz, limited by the detector used. The ultra-low loss devices demonstrated in this work, together with the strong second- and third-order nonlinearities in lithium niobate, open up new opportunities for creating novel passive, and active devices for frequency metrology and quantum information processing in the visible spectrum range.

physics.app-ph↗

arXiv2019

Coherent two-octave-spanning supercontinuum generation in lithium-niobate waveguides

We demonstrate coherent supercontinuum generation (SCG) in a monolithically integrated lithium-niobate waveguide, under the presence of second- and third-order nonlinear effects. We achieve more than two octaves of optical bandwidth in a 0.5-cm-long waveguide with 100-picojoule-level pulses. Dispersion engineering of the waveguide allows for spectral overlap between the SCG and the second harmonic which enables direct detection of the carrier-envelope offset frequency fCEO using a single waveguide. We measure the fCEO of our femtosecond pump source with a 30-dB signal-to-noise ratio.

physics.optics↗

arXiv2018

Integration of Quantum Emitters with Lithium Niobate Photonics

The integration of quantum emitters with integrated photonics enables complex quantum photonic circuits that are necessary for photonic implementation of quantum simulators, computers, and networks. Thin-film lithium niobate is an ideal material substrate for quantum photonics because it can tightly confine light in small waveguides and has a strong electro-optic effect that can switch and modulate single photons at low power and high speed. However, lithium niobite lacks efficient single-photon emitters, which are essential for scalable quantum photonic circuits. We demonstrate deterministic coupling of single-photon emitters with a lithium niobate photonic chip. The emitters are composed of InAs quantum dots embedded in an InP nanobeam, which we transfer to a lithium niobate waveguide with nanoscale accuracy using a pick-and place approach. An adiabatic taper transfers single photons emitted into the nanobeam to the lithium niobate waveguide with high efficiency. We verify the single photon nature of the emission using photon correlation measurements performed with an on-chip beamsplitter. Our results demonstrate an important step toward fast, reconfigurable quantum photonic circuits for quantum information processing.

quant-ph↗

arXiv2018

Ultrahigh-efficiency second-harmonic generation in nanophotonic PPLN waveguides

Periodically poled lithium niobate (PPLN) waveguide is a powerful platform for efficient wavelength conversion. Conventional PPLN converters however typically require long device lengths and high pump powers due to the limited nonlinear interaction strength. Here we use a nanostructured PPLN waveguides to demonstrate an ultrahigh normalized efficiency of 2600%/W-cm$^2$ for second-harmonic generation of 1.5-$μ$m radiation, more than 20 times higher than that in state-of-the-art diffused waveguides. This is achieved by a combination of sub-wavelength optical confinement and high-fidelity periodic poling at a first-order poling period of 4 $μ$m. Our highly integrated PPLN waveguides are promising for future chip-scale integration of classical and quantum photonic systems.

physics.app-ph↗

arXiv2016

On-chip detection of radiation guided by dielectric-loaded plasmonic waveguides

We report a novel approach for on-chip electrical detection of the radiation guided by dielectric-loaded surface plasmon polariton waveguides (DLSPPW) and DLSPPW-based components. The detection is realized by fabricating DLSPPW components on the surface of a gold (Au) pad supported by a silicon (Si) substrate supplied with aluminum pads facilitating electrical connections, with the gold pad being perforated in a specific locations below the DLSPPWs in order to allow a portion of the DLSPPW-guided radiation to leak into the Si-substrate, where it is absorbed and electrically detected. We present two-dimensional photocurrent maps obtained when the laser beam is scanning across the gold pad containing the fabricated DLSPPW components that are excited via grating couplers located at the DLSPPW tapered terminations. By comparing photocurrent signals obtained when scanning over a DLSPPW straight waveguide with those related to a DLSPPW racetrack resonator, we first determine the background signal level and then the corrected DLSPPW resonator spectral response, which is found consistent with that obtained from full wave numerical simulations. The approach developed can be extended to other plasmonic waveguide configurations and advantageously used for rapid characterization of complicated plasmonic circuits.

physics.optics↗

arXiv2016

Strong coupling and high contrast all optical modulation in atomic cladding waveguides

In recent years we are witnessing a flourish in research aimed to facilitate alkali vapors in guided wave configurations. Owing to the significant reduction in device dimensions, the increase in density of states, the interaction with surfaces and primarily the high intensities carried along the structure, a rich world of light vapor interactions can be studied, and new functionalities, e.g. low power nonlinear light-matter interactions can be achieved. One immense remaining challenge is to study the effects of quantum coherence and shifts in such nano-scale waveguides, characterized by ultra-small mode areas and fast dynamics. Here, we construct a serpentine silicon-nitride wave guide, having atomic vapor as its cladding. The unprecedented mode volume of 5e-13 m^3 supported over a length of 17 mm is used to demonstrate efficient linear and non-linear spectroscopy. Fascinating and important phenomena such as van der Waals shifts, dynamical stark shifts, and coherent effects such as strong coupling (in the form of Autler Townes splitting) are all observed. The serpentine atomic cladding is a promising building block for a variety of light vapor experiments, as it offers a very small footprint, enables operation with relatively low density of atoms and extremely strong confinement of light and vapor. As such it may be used for important applications, such as all optical switching, frequency referencing, and magnetometry to name a few.

physics.optics↗

arXiv2015

On-chip integrated, silicon-graphene plasmonic Schottky photodetector, with high responsivity and avalanche photogain

We report an on-chip integrated metal-graphene-silicon plasmonic Schottky photodetector with 85mA/W responsivity at 1.55 um and 7% internal quantum efficiency. This is one order of magnitude higher than metal-silicon Schottky photodetectors operated in the same conditions. At a reverse bias of 3V, we achieve avalanche multiplication, with 0.37A/W responsivity and avalanche photogain~2. This paves the way to graphene integrated silicon photonics.

cond-mat.mes-hall↗