arXiv subjects

Botao Fu

Publications and source records attributed to Botao Fu.

At least 19 recordsLinked to original sources

arXiv2026

Hybrid-Integrated DFB-Laser-Coupled 1 * 8 Thin-Film Lithium Niobate Modulator Array for High-Speed Parallel Optical Transmitters

Thin-film lithium niobate (TFLN) electro-optic modulators are attractive for high-speed optical interconnects, but scalable transmitter architectures require not only high modulation bandwidth but also multi-channel optical power distribution and practical laser-to-chip integration. Here, we demonstrate a hybrid-integrated 1 * 8 TFLN electro-optic modulator array passively butt-coupled to a 1550 nm distributed-feedback laser. The chip integrates a three-stage cascaded 1 * 2 multimode-interference splitter, spot-size converters, eight traveling-wave Mach-Zehnder modulators, thermal tuning electrodes, and on-chip 50 {\Omega} terminations. The cascaded splitter provides uniform optical power distribution with a maximum normalized power deviation of 9.7%, while the optimized electrodes enable electro-optic 3 dB bandwidths exceeding 40 GHz for all channels. The measured half-wave voltages are 3.60-3.83 V, corresponding to V{\pi}L products of 2.52-2.68 V cm for a 7 mm modulation length, and the extinction ratio reaches approximately 25 dB. The bare-chip insertion loss is 15.19-16.55 dB, and DFB laser bonding introduces an additional coupling loss of approximately 5 dB while preserving channel uniformity. These results establish a practical TFLN-based multi-channel modulator platform and represent a step toward compact hybrid-integrated optical transmitters for high-speed parallel interconnects.

physics.optics↗

arXiv2026

Doping induced itinerant ferromagnetism and enhanced ferroelectricity in BL-InSe

The microscopic coexistence of ferroelectricity and ferromagnetism in solids remains a fundamental challenge in condensed matter physics, with far-reaching implications for multifunctional materials and next-generation electronic devices. Using first-principles calculations, we predict emergent sliding ferroelectricity and doping-mediated ferromagnetism in bilayer (BL) InSe. The energetically favored AB stacked BL-InSe spontaneously breaks the out-of-plane mirror symmetry, resulting in a switchable polarization with a saturated component of 0.089 pC/m and a low transition barrier of 28.8 meV per unit cell. Strikingly, low-concentration electrostatic doping enhances rather than suppresses the ferroelectric polarization due to the abnormal layer-dependent electronic occupation in BL-InSe, in contrast to the conventional screening paradigm. In addition, the characteristic Mexican-hat-shaped valence band enables doping-induced itinerant half-metallic ferromagnetism, where the interlayer spin density difference scales linearly with doping concentration and can be reversed by switching the polarization direction. These results demonstrate the coexistence of ferroelectric and ferromagnetic orders in BL-InSe and establish a viable platform for realizing voltage-tunable multiferroicity through stacking and carrier doping in otherwise nonpolar and nonmagnetic semiconductors.

cond-mat.mtrl-sci↗

arXiv2026

Engineering Ideal 2D Type-II Nodal Line Semimetals via Stacking and Intercalation of van der Waals Layers

Two-dimensional type-II topological semimetals (TSMs), characterized by strongly tilted Dirac cones, have attracted intense interest for their unconventional electronic properties and exotic transport behaviors. However, rational design remains challenging due to the sensitivity of band tilting to lattice geometry, atomic coordination, and symmetry constraints. Here, we present a bottom-up approach to engineer ideal type-II nodal line semimetals (NLSMs) in van der Waals bilayers via atomic intercalation. Using monolayer $h$-AlN as a prototype, we show that fluorine-intercalated bilayer AlN (F@BL-AlN) hosts a symmetry-protected type-II nodal loop precisely at the Fermi level, enabled by preserved mirror symmetry ($\mathcal{M}_z$) and tailored interlayer hybridization. First-principles calculations reveal that fluorine not only tunes interlayer coupling but also aligns the Fermi energy with the nodal line, stabilizing the type-II NLSM phase. The system exhibits tunable electronic properties under external electric and strain fields and features a van Hove singularity that induces spontaneous ferromagnetism, realizing a ferromagnetic topological semimetal state. This work provides a versatile platform for designing type-II NLSMs and offers practical guidance for their experimental realization.

cond-mat.mtrl-sci↗

arXiv2025

Monolithic low-noise erbium-doped thin-film lithium niobate waveguide amplifier with 18 dB fiber to fiber net gain

Erbium-doped waveguide amplifiers have captured great attentions in recent years due to the rapid advance of photonic integration materials and fabrication techniques. In this work, a compact erbium-doped thin-film lithium niobate waveguide amplifier integrated with high-efficiency edge-couplers on the small footprint of 2 mm{\cross}25 mm, achieving >18 dB fiber-to-fiber (off-chip) net gain with bidirectional pumping by ~1480 nm laser diodes, is fabricated by the photolithography assisted chemo-mechanical etching technique. The fiber-to-fiber noise figures of the amplifier are also characterized to be around 5 dB, and the maximum amplified signal powers at the output fiber are above 13 dBm. Theoretical amplifier modeling resolving the erbium absorption and emission spectra predicts the efficient gain scaling with waveguide length for most of the telecom C-band wavelengths. The demonstrated high-external-gain erbium-doped waveguide amplifier will benefit various applications from optical communication and metrology to integrated photonic computing and artificial intelligence

physics.optics↗

arXiv2025

Ferroelectrically Controlled Chirality Switching of Weyl Quasiparticles

Weyl quasiparticles, as gapless low-energy excitations with nontrivial chirality, have garnered extensive interest in recent years. However, archieving effective and reversible control over their chirality (topological charge) remains a major challeng due to topological protection. In this work, we propose a ferroelectric mechanism to switch the chirality of Weyl phonons, where the reversal of ferroelectric polarization is intrinsically coupled to a simultaneous reversal of the chirality of Weyl points. This enables electric-field-driven control over the topological properties of phonon excitations. Through a comprehensive symmetry analysis of polar space groups, we identify 27 groups capable of hosting symmetry-protected Weyl phonons with chiral charges $C = 1$, $2$, and $3$, whose chirality can be reversed via polarization switching. The first-principles calculations are performed to screen feasible material candidates for each type of chirality, yielding a set of prototypical ferroelectric compounds that realize the proposed mechanism. As a representative example, K$_2$ZnBr$_4$ hosts the minimal configuration of two pairs of Weyl phonons. Upon polarization reversal, the chirality of all Weyl points is inverted, accompanied by a reversal of associated topological features such as Berry curvature and surface arcs. These findings provide a viable pathway for dynamic, electrical control of topological band crossings and open new avenues for chirality-based phononic applications.

cond-mat.mtrl-sci↗

arXiv2025

Type-III Weyl Semi-Half-Metal in an Ultralight Monolayer Li$_2$N

The interplay between magnetic ordering and band topology has emerged as a fertile ground for discovering novel quantum states with profound implications for fundamental physics and next-generation electronics. Here, we theoretically predict a new type-III Weyl semi-half-metal (SHM) state in monolayer Li$_2$N, uniquely combining magnetic half-metallicity and type-III Weyl semimetal characteristics. First-principles calculations reveal a fully spin-polarized and critically tilted Weyl cone around the Fermi level in monolayer Li$_2$N, driven by $p$-orbital ferromagnetism. This arises from the symmetry-protected band crossing between a flat valence band and a highly dispersive conduction band, leading to type-III Weyl fermions with strong transport anisotropy. A low-energy $k{\cdot}p$ Hamiltonian is constructed and corresponding nontrivial edge states are uncovered to capture the topological nature of Li$_2$N. Notably, this Weyl SHM phase remains robust under biaxial strain ranging from -2$\%$ to $4\%$, with an ideal type-III Weyl fermion emerging alongside a line-like ergodic surface emerging at 3.7$\%$ strain, offering a promising platform for exploring correlated electronic phenomena. Our results establish Li$_2$N as a viable candidate for realizing exotic type-III Weyl SHM states and open a new avenue for exploring the intricate interplay among magnetism, topology, and flat-band physics.

cond-mat.mtrl-sci↗

arXiv2024

Frequency stabilization based on H13C14N absorption in lithium niobate micro-disk laser

We demonstrate an on-chip lithium niobate micro-disk laser based on hydrogen cyanide (H13C14N) gas saturation absorption method for frequency stabilization. The laser chip consists of two main components: a micro-disk laser and a combined racetrack ring cavity. By operating on the H13C14N P12 absorption line at 1551.3 nm, the laser frequency can be precisely stabilized. The laser demonstrates remarkable stability, achieving a best stability value of 9*10^-9. Furthermore, the short-term stability, evaluated over continuous time intervals of 35 seconds, showcases exceptional performance. Additionally, the residual drift remains well below 30 MHz.

physics.optics↗

arXiv2024

An integrated electro-optically tunable multi-channel interference cavity laser

We demonstrated a continuously tunable laser system by butt coupling a reflective semiconductor optical amplifier (RSOA) chip with a thin-film lithium niobate (TFLN) based multi-channel interference (MCI) cavity chip. This hybrid integrated lasers allows for fine-tuning of the laser wavelength from 1538 nm to 1560 nm with a resolution of 0.014 nm and a side-mode suppression ratio (SMSR) exceeding 30 dB. The MCI cavity chip is fabricated using the photolithography assisted chemo-mechanical etching (PLACE) technique. The developed laser has an output power of approximately 10 {\mu}W, which can be further amplified to 70 mW using a commercial erbium-doped fiber amplifier (EDFA) without significant broadening of the laser linewidth.

physics.optics↗

arXiv2024

Theoretical Design of Mono-Elemental Ferroelectricity with Tunable Spin Textures in Bilayer Tellurium

2D Ferroelectricity with switchable electric polarization has drawn widespread attention in condensed matter physics due to its crucial applications in non-volatile memory and ferroelectric spin devices. Despite recent progress in 2D ferroelectric, achieving the mono-elemental ferroelectricity still remains a great challenge because most nonmetallic mono-elemental materials are stabilized in nonpolar crystal structures. In this work, we theoretically designed mono-elemental ferroelectricity with tunable and significant spin textures in bilayer tellurium (BL-Te). Comprehensive quantitative polarization calculations demonstrate that asymmetric stacking in BL-Te can generate out-of-plane (OOP) polarization with a magnitude of 0.78 pC/m. This polarization stems from distinguishing interlayer and intra-layer contributions. Moreover, these stacked BL-Te, characterized by significant spin-orbit coupling, serve as an ideal platform for investigating both conventional spin polarization and layer-dependent/hidden spin polarization through ferroelectric reversion. Our work not only broaden the category of 2D mono-elemental ferroelectric but also offer a new platform for multifunctional nanodevices.

cond-mat.mtrl-sci↗

arXiv2023

Integrated multi-color Raman microlasers with ultra-low pump levels in single high-Q lithium niobate microdisks

Photonic integrated Raman microlasers, particularly discrete multi-color lasers which are crucial for extending the emission wavelength range of chip-scale laser sources to much shorter wavelength, are highly in demand for various spectroscopy, microscopy analysis, and biological detection. However, integrated multi-color Raman microlasers have yet to be demonstrated because of the requirement of high-Q microresonators possessing large second-order nonlinearity and strong Raman phonon branches and the challenging in cavity-enhanced multi-photon hyper-Raman scattering parametric process. In this work, integrated multi-color Raman lasers have been demonstrated for the first time at weak pump levels, via the excitation of high-Q (>6 X 10^6) phase-matched modes in single thin-film lithium niobate (TFLN) microresonators by dispersion engineering. Raman lasing was observed at 1712 nm for a 1546-nm pump threshold power of only 620 uW. Furthermore, multi-color Raman lasers were realized at discrete wavelengths of 1712 nm, 813 nm, 533 nm and 406 nm with pump levels as low as 1.60 mW, which is more than two order of magnitude lower than the current records (i.e., 200 mW) in bulk resonators, allowed by the fulfillment of the requisite conditions consisting of broadband natural phase match, multiple-resonance and high Q-factors.

physics.optics↗

arXiv2023

Two-dimensional double-kagome-lattice nitrogene: a direct band gap semiconductor with nontrivial corner state

Based on first-principles calculations, we predict that nitrogen atoms can assemble into a single-layer double kagome lattice (DKL), which possesses the characteristics of an intrinsic direct band gap semiconductor, boasting a substantial band gap of 3.460 eV. The DKL structure results in a flat valence band with high effective mass and a conduction band with small effective mass comes from Dirac electrons. These distinctive band edges lead to a significant disparity in carrier mobilities, with electron mobility being four orders of magnitude higher than that of holes. The presence of flat band in DKL-nitrogene can be further discerned through the enhanced optical absorption and correlated effects as exemplified by hole-induced ferromagnetism. Interestingly, DKL-nitrogene exhibits inherent second-order topological states, confirmed by a non-trivial second Stiefel-Whitney number and the presence of 1D floating edge states and 0D corner states within the bulk band gap. Additionally, the robust N-N bonds and the lattice's bending structure ensure thermodynamic stability and mechanical stiffness. These attributes make it exceptionally stable for potential applications in nano-devices.

cond-mat.mtrl-sci↗

arXiv2023

Designing superhard magnetic material in clathrate \b{eta}-C3N2 through atom embeddedness

Designing new compounds with the coexistence of diverse physical properties is of great significance for broad applications in multifunctional electronic devices. In this work, based on density functional theory, we predict the coexistence of mechanical superhardness and the controllable magnetism in the clathrate material \b{eta}-C3N2 through the implant of the external atom into the intrinsic cage structure. Taking hydrogen-doping (H@\b{eta}-C3N2) and fluorine-doping (F@\b{eta}-C3N2) as examples, our calculations indicate these two doped configurations are stable and discovered that they belong to antiferromagnetic semiconductor and ferromagnetic semi-metal, respectively. These intriguing magnetic phase transitions originate from their distinctive band structure around the Fermi level and can be well understood by the 3D Hubbard model with half-filling occupation and the Stoner model. Moreover, the high Vickers hardness of 49.0 GPa for H@\b{eta}-C3N2 and 48.2 GPa for F@\b{eta}-C3N2 are obtained, suggesting they are clathrate superhard materials as its host. Therefore, the incorporation of H and F in \b{eta}-C3N2 gives rise to a new type of superhard antiferromagnetic semiconductor and superhard ferromagnetic semimetal, respectively, which could have potential applications in harsh conditions. Our work provides an effective strategy to design a new class of highly desirable multifunctional materials with excellent mechanical properties and magnetic properties, which may arouse spintronic applications in superhard materials in the future.

cond-mat.mtrl-sci↗

arXiv2023

Design monolayer iodinenes based on halogen bond and tiling theory

Xenes, two-dimensional (2D) monolayers composed of a single element, with graphene as a typical representative, have attracted widespread attention. Most of the previous Xenes, X from group-IIIA to group-VIA elements have bonding characteristics of covalent bonds. In this work, we for the first time unveil the pivotal role of a halogen bond, which is a distinctive type of bonding with interaction strength between that of a covalent bond and a van der Waals interaction, in 2D group-VIIA monolayers. Combing the ingenious non-edge-to-edge tiling theory and state-of-art ab initio method with refined local density functional M06-L, we provide a precise and effective bottom-up construction of 2D iodine monolayer sheets, iodinenes, primarily governed by halogen bonds, and successfully design a category of stable iodinenes, encompassing herringbone, Pythagorean, gyrated truncated hexagonal, i.e. diatomic-kagome, and gyrated hexagonal tiling pattern. These iodinene structures exhibit a wealth of properties, such as flat bands, nontrivial topology, and fascinating optical characteristics, offering valuable insights and guidance for future experimental investigations. Our work not only unveils the unexplored halogen bonding mechanism in 2D materials but also opens a new avenue for designing other non-covalent bonding 2D materials.

cond-mat.mtrl-sci↗

arXiv2023

Flat-band and multi-dimensional fermions in Pb10(PO4)6O4

Employing a combination of first-principles calculations and low-energy effective models, we present a comprehensive investigation on the electronic structure of Pb$_{10}$(PO$_{4}$)$_{6}$O$_{4}$, which exhibits remarkable quasi-one-dimensional flat-band around the Fermi level that contains novel multi-dimensional fermions. These flat bands predominantly originate from $p_x/p_y$ orbital of the oxygen molecules chain at $4e$ Wyckoff positions, and thus can be well-captured by a four-band tight-binding model. Furthermore, the abundant crystal symmetry inherent to Pb$_{10}$(PO$_{4}$)$_{6}$O$_{4}$ provides an ideal platform for the emergence of various multi-dimensional fermions, including a 0D four-fold degenerated Dirac fermion with quadratic dispersion, a 1D quadratic/linear nodal-line (QNL/LNL) fermion along symmetric $k$-paths, 1D hourglass nodal-line (HNL) fermion linked to the Dirac fermion, and a 2D symmetry-enforced nodal surface (NS) found on the $k_z$=$\pi$ plane. Moreover, when considering the weak ferromagnetic order, Pb$_{10}$(PO$_{4}$)$_{6}$O$_{4}$ transforms into a rare semi-half-metal, which is characterized by the presence of Dirac fermion and HNL fermion at the Fermi level for a single spin channel exhibiting 100$\%$ spin polarization. Our findings reveal the coexistence of flat bands, diverse topological semimetal states and ferromagnetism within in Pb$_{10}$(PO$_{4}$)$_{6}$O$_{4}$, which may provide valuable insights for further exploring intriguing interplay between superconductivity and exotic electronic states.

cond-mat.mtrl-sci↗

arXiv2023

Generation of Kerr soliton microcomb in a normally dispersed lithium niobate microdisk resonator by mode trimming

Anomalous microresonator dispersion is mandatory for Kerr soliton microcomb formation, which depends critically on the geometry of the microresonator and can hardly be tuned after the structure is made. To date, cavity-based microcombs have only been generated with fundamental whispering gallery modes (WGMs) of anomalous dispersion in microresonators. Moreover, microcomb generation in highly Raman-active platforms such as lithium niobate (LN) microresonators frequently suffers from stimulated Raman scattering and mode crossing due to the existence of multiple families of high-order WGMs. Here, we reveal a unique Kerr soliton microcomb generation mechanism through mode trimming in a weakly perturbed LN microdisk resonator. Remarkably, the soliton comb is generated with fundamental WGMs of normal dispersion and free from the mode crossing and Raman scattering effects. A robust soliton with a spectrum spanning from 1450 nm to 1620 nm at an on-chip pump power of 35 mW. Our discovery offers a powerful solution to circumvent the stringent requirements on high-precision dispersion engineering and termination of Raman excitation for soliton generation in the high-Q microdisk.

physics.optics↗

arXiv2023

2D Ladder polyborane: an ideal Dirac semimetal with a multi-feld-tunable band gap

Hydrogen, a simple and magic element, has attracted increasing attention for its effective incorporation within solids and powerful manipulation of electronic states. Here, we show that hydrogenation tackles common problems in two-dimensional borophene, e.g., stability and applicability. As a prominent example, a ladder-like boron hydride sheet, named as 2D ladder polyborane, achieves the desired outcome, enjoying the cleanest scenario with an anisotropic and tilted Dirac cone, that can be fully depicted by a minimal two-band tight-binding model. Introducing external fields, such as an electric field or a circularly-polarized light field can effectively induce distinctive massive Dirac fermions, whereupon four types of multi-field-driven topological domain walls hosting tunable chirality and valley indexes are further established. Moreover, the 2D ladder polyborane is thermodynamically stable at room temperature and supports highly switchable Dirac fermions, providing an ideal platform for realizing and exploring the various multi-field-tunable electronic states.

cond-mat.mes-hall↗

arXiv2023

Hybrid Nodal-chain Semimetal State in MgCaN2

The distinct over-tilting of band crossings in topological semimetal generates the type-I and typeII classification of Dirac/Weyl and nodal-line fermions, accompanied by the exotic electronic and magnetic transport properties. In this work, we propose a concept of hybrid nodal-chain semimetal, which is identified by the linked type-I and type-II nodal rings in the Brillouin zone. Based on first-principles calculations and swarm-intelligence structure search technique, a new ternary nitride MgCaN2 crystal is proposed as the first candidate to realize a novel 3D hybrid nodal-chain state. Remarkably, a flat band is emergent as a characteristic signature of such a hybrid nodal-chain along certain direction in the momentum space, thereby serving a platform to explore the interplay between topological semimetal state and flat band. Moreover, the underlying protection mechanism of the hybrid nodal-chain is revealed by calculating the mirror Z2 invariant and developing a k.p effective Hamiltonian. Additionally, considerable drumhead-like surface states with unique connection patterns are illustrated to identify the non-trivial band topology, which may be measured by future experiments.

cond-mat.mtrl-sci↗

arXiv2022

Modes trimming and clustering in a weakly perturbed high-Q whispering gallery microresonator

In general, a high-Q microresonator can accommodate abundant whispering gallery modes (WGMs) with the mode number increasing with the dimensional sizes of the microresonator. Removing the unnecessary modes while reorganizing the remaining modes is of vital importance, which, however, has been proved challenging and usually results in a tradeoff with the Q of the microresonator. Here, we reveal an effective and controllable mode trimming and clustering mechanism underlying the generation of polygon and star modes in weakly perturbed tapered fiber-coupled lithium niobate whispering gallery microresonators. Experimentally, various polygon and star modes are observed in sequence within a single microresonator by tuning the excitation wavelength or varying the coupling position between a tapered fiber and the circular microresonator, which can be well reproduced with our theoretical model. The finding offers a ubiquitous solution for a broad range of applications requiring elaborate selection and organization of the high-Q WGMs.

physics.optics↗