arXiv subjects

Clément Lacroûte

Publications and source records attributed to Clément Lacroûte.

16 recordsLinked to original sources

arXiv2025

Sub-kelvin measurement of silicon thermal expansion with a Fabry-Pérot cavity stabilized laser

In this letter, we report the measurement of the coefficient of thermal expansion (CTE) of single-crystal silicon from 655 mK to 16 K using an ultra-stable laser based on a single-crystal silicon Fabry-Perot cavity. Below 1 K temperatures, the CTE is in the $10^{-13}$ K$^{-1}$ range with a lowest point at $\boldsymbol{α(}655$ mK$ \boldsymbol{)=} 3.5 \pm 0.4 \times 10^{-13}$ K$^{-1}$. We produce a theoretical model based on Debye and Einstein models to effectively approximate the CTE measured in this temperature range. This is the lowest-temperature CTE measurement of silicon to date, as well as the lowest operating temperature for an ultra-stable Fabry-Perot cavity for laser frequency stabilization.

physics.optics↗

arXiv2025

Development of a laser stabilized on an ultra-stable silicon cryogenic Fabry-Perot cavity for dark matter detection

Astrophysical observations suggest the existence of an unknown kind of matter in the Universe, in the frame of the $Λ$CDM model. The research field of dark matter covers an energy scale going from massive objects to ultra-light scalar fields, which are the focus of the present work. It is supposed that ultra-light scalar fields affect the length of objects, whereas the speed of light stays unchanged. It follows that Fabry-Perot cavities are ideal tools for ultra-light dark matter detection since the fluctuations in the length of a cavity can be detected on the frequency of the laser stabilized to it. At FEMTO-ST, we have set up an ultra-stable silicon cavity suitable for a test of detection of ultra-light dark matter in an energy range close to 10$^{-10}$ eV. Our 14 cm cavity is composed of two mirrors optically bonded to an ultra-rigid spacer, with each element made in single-crystal of silicon, and cooled at 17 K in order to cancel the first order thermal expansion coefficient of the silicon spacer. The projected fractional frequency stability of the laser is $3 \times 10^{-17}$, mainly limited by the thermal noise of the amorphous dielectric reflective coatings. To reach this remarkable stability, several effects have to be reduced below the thermal noise limit. While the contribution of the residual amplitude modulation is now acceptable, we are currently implementing a laser power lock with residual fluctuations lower than 3~nW and a piezoelectric-based servo loop to actively reduce the vibration noise that has to be inferior to $-110 \textrm{~dB(m s}^{-2})^2/\textrm{Hz}$ at 1 Hz. Here, we present both the status of the development of our ultra-stable laser and the mechanical response of the cavity in the presence of ultra-light dark matter.

astro-ph.IM↗

arXiv2025

Guidelines for designs for ultrastable laser with $\mathbf{10^{-17}}$ fractional frequency instability

Lasers with long coherence time and narrow linewidth are an essential tool for quantum sensors and clocks. Ultrastable cavities and laser systems are now commercially available with fractional frequency instabilities in the mid $10^{-16}$ range. This document aims to provide technical guidance for researchers starting in the field of ultrastable lasers and to give an outlook toward the next generation of improved ultrastable lasers. These guidelines have arisen from the scope of the EMPIR project ``Next generation ultrastable lasers'' ( https://www.ptb.de/empir2021/nextlasers ) with contributions from the European project partners.

physics.optics↗

arXiv2024

Preliminary characterization of a surface electrode Paul trap for frequency metrology

We are developing a single-ion optical clock based on a surface-electrode (SE) trap that we will operate with $^{171}$Yb$^+$ ions on the electric quadrupole transition at 435.5 nm. We present heating rate measurements performed with a prototype SE trap. We also introduce a new, micro-fabricated SE trapping chip using silicon on insulator technology. Electric tests were performed under ultra-high vacuum using a testing chip, including breakdown voltages measurements and flashover detection. We present suitable trapping parameters for this chip, as well as a road-map for improving its design.

physics.atom-ph↗

arXiv2024

Towards a sub-kelvin cryogenic Fabry-Perot silicon cavity

We report on the development of a sub-kelvin, single-crystal silicon Fabry-Perot cavity. Operating such a cavity below 1~K should reduce the thermal noise limit of the cavity, and by this way address the current limitations of ultrastable lasers. To further decrease mechanical losses, mirrors with silicon substrates and crystalline coatings are optically contacted to the spacer, resulting in a room-temperature finesse of 220,000. To operate our cavity at sub-kelvin temperatures, we use a dilution refrigerator able to reach temperatures down to 10 mK. We have designed a mechanical mount to house our cavity in such a cryostat, with optimized heat transfer that will decrease the cooldown time for temperatures below 1~K. The estimated thermal noise is projected to be $\sim 7{\times}10^{-19}$ at 100~mK. However, silicon cavities with crystalline mirror coatings at cryogenic temperatures have shown birefringence correlated frequency fluctuations as well as unknown additional noise mechanisms \cite{yu2023, kedar2023}. We have measured a room-temperature TEM$_{00}$ birefringent mode splitting of about 250 kHz. Understanding and measuring these noise mechanisms will be a key to attaining fractional frequency stabilities beyond state-of-the-art.

physics.ins-det↗

arXiv2023

Fully digital platform for local ultra-stable optical frequency distribution

This article reports on the use of a Field Programmable Gate Array (FPGA) platform for local ultra-stable optical frequency distribution through a 90 m-long fiber network. This platform is used to implement a fully digital treatment of the Doppler-cancellation scheme required by fiber links to be able to distribute ultra-stable frequencies. We present a novel protocol that uses aliased images of a digital synthesizer output to directly generate signals above the Nyquist frequency. This approach significantly simplifies the setup, making it easy to duplicate within a local fiber network. We demonstrate performances enabling the distribution of an optical signal with an instability below $10^{-17}$ at 1 s at the receiver end. We also use the board to implement an original characterization method. It leads to an efficient characterization of the disturbance rejection of the system that can be realized without accessing the remote output of the fiber link.

physics.ins-det↗

arXiv2022

Heating rate measurement and characterization of a prototype surface-electrode trap for optical frequency metrology

We present the characterization of a prototype surface-electrode (SE) trap as a first step towards the realization of a compact, single-ion optical clock based on Yb$^+$. The use of a SE trap will be a key factor to benefit from clean-room fabrication techniques and technological advances made in the field of quantum information processing. We succesfully demonstrated trapping at a 500 $μ$m electrodes distance and characterized our trap in terms of lifetime and heating rate. This is to our knowledge the highest distance achieved for heating rates measurements in SE traps. This simple 5-wire design realized with simple materials yields a heating rate of $\mathbf{8\times 10^3}$ phonons/s. We provide an analysis of the performances of this prototype trap for optical frequency metrology.

quant-ph↗

arXiv2022

Residual amplitude modulation at the $10^{-7}$ level for ultra-stable lasers

The stabilization of lasers on ultra-stable optical cavities by the Pound-Drever-Hall (PDH) technique is a widely used method. The PDH method relies on the phase-modulation of the laser, which is usually performed by an electro-optic modulator (EOM). When approaching the $10^{-16}$ level, this technology requires an active control of the residual amplitude modulation (RAM) generated by the EOM in order to bring the frequency stability of the laser down to the thermal noise limit of the ultra-stable cavity. In this article, we report on the development of an active system of RAM reduction based on a free space EOM, which is used to perform PDH-stabilization of a laser on a cryogenic silicon cavity. A RAM stability of $1.4 \times 10^{-7}$ is obtained by employing a digital servo that stabilizes the EOM DC electric field, the crystal temperature and the laser power. Considering an ultra-stable cavity with a finesse of $2.5\times 10^5$, this RAM level would contribute to the fractional frequency instability at the level of about $5\times 10^{-19}$, well below the state of the art thermal noise limit of a few $ 10^{-17}$.

physics.optics↗

arXiv2021

Digital Doppler-cancellation servo for ultra-stable optical frequency dissemination over fiber

Progress made in optical references, including ultra-stable Fabry-Perot cavities, optical frequency combs and optical atomic clocks, have driven the need for ultra-stable optical fiber networks. Telecom-wavelength ultra-pure optical signal transport has been demonstrated on distances ranging from the laboratory scale to the continental scale. In this manuscript, we present a Doppler-cancellation setup based on a digital phase-locked loop for ultra-stable optical signal dissemination over fiber. The optical phase stabilization setup is based on a usual heterodyne Michelson-interferometer setup, while the Software Defined Radio (SDR) implementation of the phase-locked loop is based on a compact commercial board embedding a field programmable gate array, analog-to-digital and digital-to-analog converters. Using three different configurations including an undersampling method, we demonstrate a 20 m long fiber link with residual fractional frequency instability as low as $10^{-18}$ at 1000 s, and an optical phase noise of $-70$ dBc/Hz at 1 Hz with a telecom frequency carrier.

physics.ins-det↗

arXiv2019

Ultra-compact reference ULE cavity

We present a first experimental characterization of our ultra-compact, ultra-stable laser. The heart of the apparatus is an original Fabry-Perot cavity with a 25 mm length and a pyramidal geometry, equipped with highly-reflective crystalline coatings. The cavity, along with its vacuum chamber and optical setup, fits inside a 30 L volume. We have measured the cavity thermal and vibration sensitivities, and present a first estimation of the cavity fractional frequency instability at $σ_y(1\rm{s})=7.5{\times}10^{-15}$.

physics.ins-det↗

arXiv2019

Absolute frequency measurements of the ${}^1{\rm S}_0 \rightarrow {}^1{\rm P}_1$ transition in ytterbium

The ytterbium atom is widely used in the fields of atomic physics, cavity quantum electrodynamics, quantum information processing and optical frequency standards. There is however a strong dispersion among the reported values of the ${}^1{\rm S}_0 \rightarrow {}^1{\rm P}_1$ transition frequency. In this article, we present two independent measurements of the absolute frequency of this transition performed with two different wavemeters using atomic fluorescence spectroscopy. The cancellation of Doppler shifts is obtained by fine tuning the angle between the probe laser and the atomic beam. The resulting $^{174}\mathrm{Yb}$ isotope transition frequency is estimated to be $\,751\,526\,537\pm27$ MHz.

physics.atom-ph↗

arXiv2018

Single-ion, transportable optical atomic clocks

For the past 15 years, tremendous progress within the fields of laser stabilization, optical frequency combs and atom cooling and trapping have allowed the realization of optical atomic clocks with unrivaled performances. These instruments can perform frequency comparisons with fractional uncertainties well below $10^{-17}$, finding applications in fundamental physics tests, relativistic geodesy, and time and frequency metrology. Even though most optical clocks are currently laboratory setups, several proposals for using these clocks for field measurements or within an optical clock network have been published, and most of time and frequency metrology institutes have started to develop transportable optical clocks. For the purpose of this special issue, we chose to focus on trapped-ion optical clocks. Even though their short-term fractional frequency stability is impaired by a lower signal-to-noise ratio, they offer a high potential for compactness: trapped ions demand low optical powers and simple loading schemes, and can be trapped in small vacuum chambers. We review recent advances on the clock key components, including ion trap and ultra-stable optical cavity, as well as existing projects and experiments which draw the picture of what future transportable, single-ion optical clocks may resemble.

physics.atom-ph↗

arXiv2018

Photonic Generation of High Power, Ultrastable Microwave Signals by Vernier Effect in a Femtosecond Laser Frequency Comb

Optical frequency division of an ultrastable laser to the microwave frequency range by an optical frequency comb has allowed the generation of microwave signals with unprecedently high spectral purity and stability. However, the generated microwave signal will suffer from a very low power level if no external optical frequency comb repetition rate multiplication device is used. This paper reports theoretical and experimental studies on the beneficial use of the Vernier effect together with the spectral selective filtering in a double directional coupler add-drop optical fibre ring resonator to increase the comb repetition rate and generate high power microwaves. The studies are focused on two selective filtering aspects: the high rejection of undesirable optical modes of the frequency comb and the transmission of the desirable modes with the lowest possible loss. Moreover, the conservation of the frequency comb stability and linewidth at the resonator output is particularly considered. Accordingly, a fibre ring resonator is designed, fabricated, and characterized, and a technique to stabilize the resonator's resonance comb is proposed. A significant power gain is achieved for the photonically generated beat note at 10 GHz. Routes to highly improve the performances of such proof-of-concept device are also discussed.

physics.ins-det↗

arXiv2017

Residual Phase Noise Measurement of Optical Second Harmonic Generation in PPLN Waveguides

We report on the characterization, including residual phase noise and fractional frequency instability, of fiber-coupled PPLN non-linear crystals. These components are devoted to frequency doubling 871 nm light from an extended-cavity diode laser to produce a 435.5 nm beam, corresponding to the ytterbium ion electric quadrupole clock transition. We measure doubling efficiencies of up to 117.5 %/W. Using a Mach-Zehnder interferometer and an original noise rejection technique, the residual phase noise of the doublers is estimated to be lower than ${\rm -35\, dBrad^2/Hz}$ at 1 Hz, making these modules compatible with up-to-date optical clocks and ultra-stable cavities. The influence of external parameters such as pump laser frequency and intensity is investigated, showing that they do not limit the stability of the frequency-doubled signal. Our results demonstrate that such compact, fiber-coupled modules are suitable for use in ultra-low phase noise metrological experiments, including transportable optical atomic clocks.

physics.ins-det↗

arXiv2016

Compact Yb$^+$ optical atomic clock project: design principle and current status

We present the design of a compact optical clock based on the $^2S_{1/2} \rightarrow ^2D_{3/2}$ 435.5 nm transition in $^{171}$Yb$^+$. The ion trap will be based on a micro-fabricated circuit, with surface electrodes generating a trapping potential to localize a single Yb ion a few hundred $μ$m from the electrodes. We present our trap design as well as simulations of the resulting trapping pseudo-potential. We also present a compact, multi-channel wavelength meter that will permit the frequency stabilization of the cooling, repumping and clear-out lasers at 369.5 nm, 935.2 nm and 638.6 nm needed to cool the ion. We use this wavelength meter to characterize and stabilize the frequency of extended cavity diode lasers at 369.5 nm and 638.6 nm.

physics.atom-ph↗

arXiv2015

Frequency stability of a wavelength meter and applications to laser frequency stabilization

Interferometric wavelength meters have attained frequency resolutions down to the MHz range. In particular, Fizeau interferometers, which have no moving parts, are becoming a popular tool for laser characterization and stabilization. In this article, we characterize such a wavelength meter using an ultra-stable laser in terms of relative frequency instability $σ_y(τ)$ and demonstrate that it can achieve a short-term instability $σ_y(1 s) \approx 2{\times}10^{-10}$ and a frequency drift of order $10$ MHz/day. We use this apparatus to demonstrate frequency control of a near-infrared laser, where a frequency instability below $3{\times}10^{-10}$ from 1 s to 2000 s is achieved. Such performance is for example adequate for ions trapping and atoms cooling experiments.

physics.optics↗