Searcharxiv⌕ Search

arXiv subjects

Emma E. Wollman

Publications and source records attributed to Emma E. Wollman.

At least 19 recordsLinked to original sources
arXiv2026

Enhanced Mid-Infrared Single-Photon Detection with Antenna-Coupled Superconducting Nanowires

Scaling the photon-detection area of superconducting nanowire single-photon detectors (SNSPDs) has traditionally been achieved by nanowire meandering. However, material inhomogeneities and fabrication-induced defects, such as line-edge roughness, increase with nanowire length, leading to reduced internal photon-detection efficiency and elevated dark-count rates. This trade-off becomes increasingly pronounced as nanowires are scaled to sub-100 nm widths and sub-5 nm thicknesses required for mid- to far-infrared sensitivity. Here, we demonstrate an antenna-coupled SNSPD architecture that enhances the effective photon-detection area without increasing nanowire length. A crossed bowtie antenna integrated with an 80 nm-wide, 3 nm-thick WSi nanowire yields 15.7$\times$ increase in effective detection area at 7.4 $μ$m compared to a bare nanowire of identical geometric footprint, while maintaining the same internal detection efficiency and dark-count rate. Antenna coupling provides a scalable approach to increasing photon-detection area while reducing the noise-equivalent power, offering performance benefits for applications in astronomy, biological imaging, and molecular spectroscopy.

physics.optics↗
arXiv2026

Tungsten Germanide Superconducting Nanowire Single-Photon Detectors with Saturated Internal Detection Efficiency at Wavelengths up to 29 μm

Superconducting nanowire single-photon detectors (SNSPDs) are among the most sensitive single-photon detectors available and have the potential to transform fields ranging from infrared astrophysics to molecular spectroscopy. However, extending their performance into the mid-infrared spectral region - crucial for applications such as exoplanet transit spectroscopy and vibrational fingerprinting of molecules - has remained a major challenge, primarily due to material limitations and scalability constraints. Here, we report on the development of SNSPDs based on tungsten germanide, a novel material system that combines high mid-infrared sensitivity with compatibility for large-scale fabrication. Our detectors exhibit saturated internal detection efficiency at wavelengths up to 29 μm, while using 2.7x thicker films (8 nm vs 3 nm) and up to 4.5x wider nanowires (360 nm vs 80 nm) compared to mid-infrared-optimized SNSPDs fabricated from tungsten silicide. This advance will enable scalable, high-performance single-photon detection in a spectral region that was previously inaccessible, opening new frontiers in remote sensing, thermal imaging, environmental monitoring, molecular physics, and astronomy.

physics.ins-det↗
arXiv2025

High-efficiency, high-count-rate 2D superconducting nanowire single-photon detector array

Superconducting nanowire single-photon detectors (SNSPDs) are the current leading technology for the detection of single-photons in the near-infrared (NIR) and short-wave infrared (SWIR) spectral regions, due to record performance in terms of detection efficiency, low dark count rate, minimal timing jitter, and high maximum count rates. The various geometry and design parameters of SNSPDs are often carefully tailored to specific applications, resulting in challenges in optimising each performance characteristic without adversely impacting others. In particular, when scaling to larger array formats, the key challenge is to manage the heat load generated by the many readout cables in the cryogenic cooling system. Here we demonstrate a practical, self-contained 64-pixel SNSPD array system which exhibits high performance of all operational parameters, for use in the strategically important SWIR spectral region. The detector is an 8x8 array of 27.5 x 27.8 μm pixels on a 30 μm pitch, which leads to an 80 -- 85% fill factor. At a wavelength of 1550nm, a uniform average per-pixel photon detection efficiency of 77.7% was measured and the observed system detection efficiency (SDE) across the entire array was 65%. A full performance characterisation is presented, including a dark count rate of 20 cps per pixel, full-width-half-maximum (FWHM) jitter of 100 ps per pixel, a 3-dB maximum count rate of 645 Mcps and no evidence of crosstalk at the 0.1% level. This camera system therefore facilitates a variety of picosecond time-resolved measurement-based applications that include biomedical imaging, quantum communications, and long-range single-photon light detection and ranging (LiDAR) and 3D imaging.

quant-ph↗
arXiv2024

An SNSPD-based detector system for NASA's Deep Space Optical Communications project

We report on a free-space-coupled superconducting nanowire single-photon detector array developed for NASA's Deep Space Optical Communications project (DSOC). The array serves as the downlink detector for DSOC's primary ground receiver terminal located at Palomar Observatory's 200-inch Hale Telescope. The 64-pixel WSi array comprises four quadrants of 16 co-wound pixels covering a 320 micron diameter active area and embedded in an optical stack. The detector system also includes cryogenic optics for filtering and focusing the downlink signal and electronics for biasing the array and amplifying the output pulses. The detector system exhibits a peak system detection efficiency of 76% at 1550 nm, a background-limited false count rate as low as 3.7 kcps across the array, timing jitter less than 120 ps FWHM, and a maximum count rate of ~ 1 Gcps.

physics.ins-det↗
arXiv2024

Improvements of readout signal integrity in mid-infrared superconducting nanowire single photon detectors

Superconducting nanowire single-photon detectors (SNSPDs) with high timing resolution and low background counts in the mid infrared (MIR) have the potential to open up numerous opportunities in fields such as exoplanet searches, direct dark matter detection, physical chemistry, and remote sensing. One challenge in pushing SNSPD sensitivity to the MIR is a decrease in the signal-to-noise ratio (SNR) of the readout signal as the critical currents become increasingly smaller. We overcome this trade-off with a new device architecture that employs impedance matching tapers and superconducting nanowire avalanche photodetectors to demonstrate increased SNR while maintaining saturated internal detection efficiency at 7.4 μm and getting close to saturation at 10.6 μm. This work provides a novel platform for pushing SNSPD sensitivity to longer wavelengths while improving the scalability of the readout electronics.

physics.ins-det↗
arXiv2023

Low-noise single-photon counting superconducting nanowire detectors at infrared wavelengths up to 29 $μ$m

We report on the extension of the spectral sensitivity of superconducting nanowire single-photon detectors to a wavelength of 29 $μ$m. This represents the first demonstration of a time correlated single-photon counting detector at these long infrared wavelengths. We achieve saturated internal detection efficiency from 10 to 29 $μ$m, whilst maintaining dark count rates below 0.1 counts per second. Extension of superconducting nanowire single-photon detectors to this spectral range provides low noise and high timing resolution photon counting detection, effectively providing a new class of single-photon sensitive detector for these wavelengths. These detectors are important for applications such as exoplanet spectroscopy, infrared astrophysics, physical chemistry, remote sensing and direct dark-matter detection.

quant-ph↗
arXiv2023

Large active-area superconducting microwire detector array with single-photon sensitivity in the near-infrared

Superconducting nanowire single photon detectors (SNSPDs) are the highest-performing technology for time-resolved single-photon counting from the UV to the near-infrared. The recent discovery of single-photon sensitivity in micrometer-scale superconducting wires is a promising pathway to explore for large active area devices with application to dark matter searches and fundamental physics experiments. We present 8-pixel $1 mm^2$ superconducting microwire single photon detectors (SMSPDs) with $1\,\mathrm{μm}$-wide wires fabricated from WSi and MoSi films of various stoichiometries using electron-beam and optical lithography. Devices made from all materials and fabrication techniques show saturated internal detection efficiency at 1064 nm in at least one pixel, and the best performing device made from silicon-rich WSi shows single-photon sensitivity in all 8 pixels and saturated internal detection efficiency in 6/8 pixels. This detector is the largest reported active-area SMSPD or SNSPD with near-IR sensitivity published to date, and the first report of an SMSPD array. By further optimizing the photolithography techniques presented in this work, a viable pathway exists to realize larger devices with $cm^2$-scale active area and beyond.

physics.ins-det↗
arXiv2022

High-speed detection of 1550 nm single photons with superconducting nanowire detectors

Superconducting nanowire single photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate - as well as a world-leading maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires which span the mode of an optical fiber. This design supports high count rates with minimal penalties for detection efficiency and timing jitter. We show how these trade-offs can be mitigated by implementing independent read-out for each nanowire and by using a temporal walk correction technique to reduce count-rate dependent timing jitter. These detectors make quantum communication practical on a 10 GHz clock.

quant-ph↗
arXiv2022

Time-walk and jitter correction in SNSPDs at high count rates

Superconducting nanowire single-photon detectors (SNSPDs) are a leading detector type for time correlated single photon counting, especially in the near-infrared. When operated at high count rates, SNSPDs exhibit increased timing jitter caused by internal device properties and features of the RF amplification chain. Variations in RF pulse height and shape lead to variations in the latency of timing measurements. To compensate for this, we demonstrate a calibration method that correlates delays in detection events with the time elapsed between pulses. The increase in jitter at high rates can be largely canceled in software by applying corrections derived from the calibration process. We demonstrate our method with a single-pixel tungsten silicide SNSPD and show it decreases high count rate jitter. The technique is especially effective at removing a long tail that appears in the instrument response function at high count rates. At a count rate of 11.4 MCounts/s we reduce the full width at one percent maximum level (FW1%M) by 45%. The method therefore enables certain quantum communication protocols that are rate-limited by the (FW1%M) metric to operate almost twice as fast. \c{opyright} 2022. All rights reserved.

quant-ph↗
arXiv2022

Picosecond Synchronization of Photon Pairs through a Fiber Link between Fermilab and Argonne National Laboratories

We demonstrate a three-node quantum network for C-band photon pairs using 2 pairs of 59 km of deployed fiber between Fermi and Argonne National Laboratories. The C-band pairs are directed to nodes using a standard telecommunication switch and synchronized to picosecond-scale timing resolution using a coexisting O- or L-band optical clock distribution system. We measure a reduction of coincidence-to-accidental ratio (CAR) of the C-band pairs from 51 $\pm$ 2 to 5.3 $\pm$ 0.4 due to Raman scattering of the O-band clock pulses. Despite this reduction, the CAR is nevertheless suitable for quantum networks.

quant-ph↗
arXiv2022

Picosecond synchronization system for quantum networks

The operation of long-distance quantum networks requires photons to be synchronized and must account for length variations of quantum channels. We demonstrate a 200 MHz clock-rate fiber optic-based quantum network using off-the-shelf components combined with custom-made electronics and telecommunication C-band photons. The network is backed by a scalable and fully automated synchronization system with ps-scale timing resolution. Synchronization of the photons is achieved by distributing O-band-wavelength laser pulses between network nodes. Specifically, we distribute photon pairs between three nodes, and measure a reduction of coincidence-to-accidental ratio from 77 to only 42 when the synchronization system is enabled, which permits high-fidelity qubit transmission. Our demonstration sheds light on the role of noise in quantum communication and represents a key step in realizing deployed co-existing classical-quantum networks.

quant-ph↗
arXiv2021

Impedance-matched differential superconducting nanowire detectors

Superconducting nanowire single-photon detectors (SNSPDs) are the highest performing photon-counting technology in the near-infrared (NIR). Due to delay-line effects, large area SNSPDs typically trade-off timing resolution and detection efficiency. Here, we introduce a detector design based on transmission line engineering and differential readout for device-level signal conditioning, enabling a high system detection efficiency and a low detector jitter, simultaneously. To make our differential detectors compatible with single-ended time taggers, we also engineer analog differential-to-single-ended readout electronics, with minimal impact on the system timing resolution. Our niobium nitride differential SNSPDs achieve $47.3\,\% \pm 2.4\,\%$ system detection efficiency and sub-$10\,\mathrm{ps}$ system jitter at $775\,\mathrm{nm}$, while at $1550\,\mathrm{nm}$ they achieve $71.1\,\% \pm 3.7\,\%$ system detection efficiency and $13.1\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ system jitter. These detectors also achieve sub-100 ps timing response at one one-hundredth maximum level, $30.7\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ at $775\,\mathrm{nm}$ and $47.6\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ at $1550\,\mathrm{nm}$, enabling time-correlated single-photon counting with high dynamic range response functions. Furthermore, thanks to the differential impedance-matched design, our detectors exhibit delay-line imaging capabilities and photon-number resolution. The properties and high-performance metrics achieved by our system make it a versatile photon-detection solution for many scientific applications.

physics.app-ph↗
arXiv2020

Teleportation Systems Towards a Quantum Internet

Quantum teleportation is essential for many quantum information technologies including long-distance quantum networks. Using fiber-coupled devices, including state-of-the-art low-noise superconducting nanowire single photon detectors and off-the-shelf optics, we achieve quantum teleportation of time-bin qubits at the telecommunication wavelength of 1536.5 nm. We measure teleportation fidelities of >=90% that are consistent with an analytical model of our system, which includes realistic imperfections. To demonstrate the compatibility of our setup with deployed quantum networks, we teleport qubits over 22 km of single-mode fiber while transmitting qubits over an additional 22 km of fiber. Our systems, which are compatible with emerging solid-state quantum devices, provide a realistic foundation for a high-fidelity quantum internet with practical devices.

quant-ph↗
arXiv2020

Demonstration of a Thermally-Coupled Row-Column SNSPD Imaging Array

While single-pixel superconducting nanowire single photon detectors (SNSPDs) have demonstrated remarkable efficiency and timing performance from the UV to near-IR, scaling these devices to large imaging arrays remains challenging. Here, we propose a new SNSPD multiplexing system using thermal coupling and detection correlations between two photosensitive layers of an array. Using this architecture with the channels of one layer oriented in rows and the second layer in columns, we demonstrate imaging capability in 16-pixel arrays with accurate spot tracking at the few photon level. We also explore the performance tradeoffs of orienting the top layer nanowires parallel and perpendicular to the bottom layer. The thermally-coupled row-column scheme is readily able to scale to the kilopixel size with existing readout systems, and when combined with other multiplexing architectures, has the potential to enable megapixel scale SNSPD imaging arrays.

physics.ins-det↗
arXiv2020

Readout of Superconducting Nanowire Single Photon Detectors through Forward Biased Optical Modulators

Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm$^2$ range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 $Ω$ with a low power dissipation of 40 $μ$W. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.

physics.app-ph↗
arXiv2019

High-Speed Low-Crosstalk Detection of a $^{171}$Yb$^+$ Qubit using Superconducting Nanowire Single Photon Detectors

Qubits used in quantum computing tend to suffer from errors, either from the qubit interacting with the environment, or from imperfect control when quantum logic gates are applied. Fault-tolerant construction based on quantum error correcting codes (QECC) can be used to recover from such errors. Effective implementation of QECC requires a high fidelity readout of the ancilla qubits from which the error syndrome can be determined, without affecting the data qubits in which relevant quantum information is stored for processing. Here, we present a detection scheme for \yb trapped ion qubits, where we use superconducting nanowire single photon detectors and utilize photon time-of-arrival statistics to improve the fidelity and speed. Qubit shuttling allows for creating a separate detection region where an ancilla qubit can be measured without disrupting a data qubit. We achieve an average qubit state detection time of 11$μ$s with a fidelity of $99.931(6)\%$. The error due to the detection crosstalk, defined as the probability that the coherence of the data qubit is lost due to the process of detecting an ancilla qubit, is reduced to $\sim2\times10^{-5}$ by creating a separation of 370$μ$m between them.

quant-ph↗
arXiv2017

UV superconducting nanowire single-photon detectors with high efficiency, low noise, and 4 K operating temperature

For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 $μ$m in diameter, 70 - 80% efficiency, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ~ 0.25 counts/hr for a 56 $μ$m diameter pixel. By using the amorphous superconductor MoSi, these UV SNSPDs are also able to operate at temperatures up to 4.2 K. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.

physics.ins-det↗