arXiv subjects

Fengquan Wu

Publications and source records attributed to Fengquan Wu.

At least 55 records · Page 3Linked to original sources

arXiv2020

Reflections and Standing Waves on the Tianlai Cylinder Array

In 21~cm intensity mapping, the spectral smoothness of the foreground is exploited to separate it from the much weaker 21~cm signal. However, the non-smooth frequency response of the instrument complicates this process. Reflections and standing waves generate modulations on the frequency response. Here we report the analysis of the standing waves in the bandpass of the signal channels of the Tianlai Cylinder Array. By Fourier transforming the bandpass into the delay time domain, we find various standing waves generated on the telescope. A standing wave with time delay at about 142 ns is most clearly identified which is produced in the 15 meter feed cable. We also find a strong peak at a shorter delay of $τ< 50 \ns$, which may be a mix of the standing wave between the reflector and feed, and the standing wave on the 4 m intermediate frequency (IF) cable. We also show that a smoother frequency response could be partially recovered by removing the reflection-inducted modulations. However, the standing wave on the antenna is direction-dependent, which poses a more difficult challenge for high precision calibration.

astro-ph.IM↗

arXiv2020

Beam Measurements of the Tianlai Dish Radio Telescope using an Unmanned Aerial Vehicle

Precision measurement of the beam pattern of an antenna is very important for many applications. While traditionally such measurement is often made in a microwave anechoic chamber or at a test range, measurement using an unmanned aerial vehicle offers a number of advantages: the measurement can be made for the assembled antenna on site, thus reflecting the actual characteristics of the antenna of interest, and more importantly, it can be performed for larger antennas which cannot be steered or easily measured using the anechoic chamber and test range. Here we report our beam measurement experiment with UAV for a 6 meter dish used in the Tianlai array, which is a radio astronomy experiment. Due to the dish's small collecting area, calibration with an astronomical source only allows for determining the antenna beam pattern over a very limited angular range. We describe in detail the setup of the experiment, the components of the signal transmitting system, the design of the flight path and the procedure for data processing. We find the UAV measurement of the beam pattern agrees very well with the astronomical source measurement in the main lobe, but the UAV measurement can be extended to the fourth side lobe. The measured position and width of each lobe also shows good agreement with electromagnetic field simulation. This UAV-based approach of beam pattern measurement is flexible and inexpensive, and the technique may also be applied to other experiments.

astro-ph.IM↗

arXiv2020

The Tianlai Cylinder Pathfinder Array: System Functions and Basic Performance Analysis

The Tianlai Cylinder Pathfinder is a radio interferometer array designed to test techniques for 21 cm intensity mapping in the post-reionization Universe, with the ultimate aim of mapping the large scale structure and measuring cosmological parameters such as the dark energy equation of state. Each of its three parallel cylinder reflectors is oriented in the north-south direction, and the array has a large field of view. As the Earth rotates, the northern sky is observed by drift scanning. The array is located in Hongliuxia, a radio-quiet site in Xinjiang, and saw its first light in September 2016. In this first data analysis paper for the Tianlai cylinder array, we discuss the sub-system qualification tests, and present basic system performance obtained from preliminary analysis of the commissioning observations during 2016-2018. We show typical interferometric visibility data, from which we derive the actual beam profile in the east-west direction and the frequency band-pass response. We describe also the calibration process to determine the complex gains for the array elements, either using bright astronomical point sources, or an artificial on site calibrator source, and discuss the instrument response stability, crucial for transit interferometry. Based on this analysis, we find a system temperature of about 90 K, and we also estimate the sensitivity of the array.

astro-ph.IM↗

arXiv2020

Forecast for FAST: from Galaxies Survey to Intensity Mapping

The Five-Hundred-Meter Aperture Spherical Radio Telescope(FAST) is the largest single-dish radio telescope in the world. In this paper, we make forecast on the FAST HI large scale structure survey by mock observations. We consider a drift scan survey with the L-band 19 beam receiver, which may be commensal with the pulsar search and Galactic HI survey. We also consider surveys at lower frequency, either using the current single feed wide band receiver, or a future multi-beam phased array feed (PAF) in the UHF band. We estimate the number density of detected HI galaxies and the measurement error in positions, the precision of the surveys are evaluated using both Fisher matrix and simulated observations. The measurement error in the HI galaxy power spectrum is estimated, and we find that the error is relatively large even at moderate redshifts, as the number of positively detected galaxies drops drastically with increasing redshift. However, good cosmological measurement could be obtained with the intensity mapping technique where the large scale HI distribution is measured without resolving individual galaxies. The figure of merit (FoM) for the dark energy equation of state with different observation times are estimated, we find that with the existing L-band multi-beam receiver, a good measurement of low redshift large scale structure can be obtained, which complements the existing optical surveys. With a PAF in the UHF band, the constraint can be much stronger, reaching the level of a dark energy task force (DETF) stage IV experiment.

astro-ph.CO↗

arXiv2019

Discovering the Sky at the Longest Wavelengths with Small Satellite Constellations

Due to ionosphere absorption and the interference by natural and artificial radio emissions, ground observation of the sky at the decameter or longer is very difficult. This unexplored part of electromagnetic spectrum has the potential of great discoveries, notably in the study of cosmic dark ages and dawn, but also in heliophysics and space weather, planets, cosmic ray and neutrinos, pulsar and interstellar medium, extragalactic radio sources, and even SETI. At a forum organized by the International Space Science Institute-Beijing (ISSI-BJ), we discussed the prospect of opening up this window for astronomical observations by using a constellation of small or micro-satellites. We discussed the past experiments and the current ones such as the low frequency payload on Chang'e-4 mission lander, relay satellite and the Longjiang satellite, and also the future DSL mission, which is a linear array on lunar orbit which can make synthesized map of the whole sky as well as measure the global spectrum. We also discuss the synergy with other experiments, including ground global experiments such as EDGES, SARAS, SCI-HI and High-z, PRIZM/Albatros, ground imaging facillities such as LOFAR and MWA, and space experiments such as SUNRISE, DARE/DAPPER and PRATUSH. We also discussed some technical aspects of the DSL concept.

astro-ph.IM↗

arXiv2019

The Design and Implementation of a ROACH2+GPU based Correlator on the Tianlai Dish Array

The digital correlator is a crucial element in a modern radio telescope. In this paper we describe a scalable design of the correlator system for the Tianlai pathfinder array, which is an experiment dedicated to test the key technologies for conducting 21cm intensity mapping survey. The correlator is of the FX design, which firstly performs Fast Fourier Transform (FFT) including Polyphase Filter Bank (PFB) computation using a Collaboration for Astronomy Signal Processing and Electronics Research (CASPER) Reconfigurable Open Architecture Computing Hardware-2 (ROACH2) board, then computes cross-correlations using Graphical Processing Units (GPUs). The design has been tested both in laboratory and in actual observation.

astro-ph.IM↗

arXiv2018

A high-resolution self-consistent whole sky foreground model

The neutral hydrogen 21cm line is potentially a very powerful probe of the observable universe, and a number of on-going experiments are trying to detect it at cosmological distances. However, the presence of strong foreground radiations such as the galactic synchrotron radiation, galactic free-free emission and extragalactic radio sources make it a very challenging task. For the design of 21cm experiments and analysis of their data, simulation is an essential tool, and good sky foreground model is needed. With existing data the whole sky maps are available only in low angular resolutions or for limited patches of sky, which is inadequate in the simulation of these new 21cm experiments. In this paper, we present the method of constructing a high resolution self-consistent sky model at low frequencies, which incorporates both diffuse foreground and point sources. Our diffuse map is constructed by generating physical foreground components including the galactic synchrotron emission and galactic free-free emission. The point source sample is generated using the actual data from the NRAO VLA Sky Survey (NVSS) and the Sydney University Molonglo Sky Survey (SUMSS) where they are available and complete in flux limit, and mock point sources according to statistical distributions. The entire model is made self-consistent by removing the integrated flux of the point sources from the diffuse map so that this part of radiation is not double counted. We show that with the point sources added, a significant angular power is introduced in the mock sky map, which may be important for foreground subtraction simulations. Our sky maps and point source catalogues are available to download.

astro-ph.CO↗

arXiv2018

An Eigenvector-based Method of Radio Array Calibration and Its Application to the Tianlai Cylinder Pathfinder

We propose an eigenvector-based formalism for the calibration of radio interferometer arrays. In the presence of a strong dominant point source, the complex gains of the array can be obtained by taking the first eigenvector of the visibility matrix. We use the stable principle component analysis (SPCA) method to help separate outliers and noise from the calibrator signal to improve the performance of the method. This method can be applied with poorly known beam model of the antenna, and is insensitive to outliers or imperfections in the data, and has low computational complexity. It thus is particularly suitable for the initial calibration of the array, which can serve as the initial point for more accurate calibrations. We demonstrate this method by applying it to the cylinder pathfinder of the Tianlai experiment, which aims to measure the dark energy equation of state using the baryon acoustic oscillation (BAO) features in the large scale structure by making intensity mapping observation of the redshifted 21~cm emission of the neutral hydrogen (HI). The complex gain of the array elements and the beam profile in the East-West direction (short axis of the cylinder) are successfully obtained by applying this method to the transit data of bright radio sources.

astro-ph.IM↗

arXiv2018

Progress in the Construction and Testing of the Tianlai Radio Interferometers

The Tianlai Pathfinder is designed to demonstrate the feasibility of using a wide field of view radio interferometers to map the density of neutral hydrogen in the Universe after the Epoch of Reionizaton. This approach, called 21~cm intensity-mapping, promises an inexpensive means for surveying the large-scale structure of the cosmos. The Tianlai Pathfinder presently consists of an array of three, 15~m $\times$ 40~m cylinder telescopes and an array of sixteen, 6~m diameter dish antennas located in a radio-quiet part of western China. The two types of arrays were chosen to determine the advantages and disadvantages of each approach. The primary goal of the Pathfinder is to make 3D maps by surveying neutral hydrogen over large areas of the sky %$20,000 {\rm deg}^2$ in two different redshift ranges: first at $1.03 > z > 0.78$ ($700 - 800$~MHz) and later at $0.21 > z > 0.12$ ($1170 - 1270$~MHz). The most significant challenge to $21$~cm intensity-mapping is the removal of strong foreground radiation that dwarfs the cosmological signal. It requires exquisite knowledge of the instrumental response, i.e. calibration. In this paper, we provide an overview of the status of the Pathfinder and discuss the details of some of the analysis that we have carried out to measure the beam function of both arrays. We compare electromagnetic simulations of the arrays to measurements, discuss measurements of the gain and phase stability of the instrument, and provide a brief overview of the data processing pipeline.

astro-ph.IM↗

arXiv2018

Extracting 21cm signal by frequency and angular filtering

Extracting the neutral hydrogen (HI) signal is a great challenge for cosmological 21cm experiments, both the astrophysical foregrounds and the receiver noise are typically several orders of magnitude greater than the 21cm signal. However, the different properties of the 21cm signal, foreground, and noise can be exploited to separate these components. The foregrounds are generally smooth or correlated over the frequency space along a line of sight (l.o.s.), while both the 21cm signal and the noise varies stochastically along the same l.o.s. The foreground can be removed by filtering out the smooth component in the frequency space. The receiver noise is basically uncorrelated for observations at different times, hence for surveys they are also uncorrelated in the different directions, while the 21cm signal which traces the large scale structure are correlated up to certain scales. In this exercise, we apply Wiener filters in frequency and angular space, to extract the 21cm signals. We found that the method works well. The inaccurate knowledge about beam could degrade the reconstruction, but the overall result is still good, showing that the method is fairly robust.

astro-ph.CO↗

arXiv2018

An imaging algorithm for a lunar orbit interferometer array

Radio astronomical observation below 30 MHz is hampered by the refraction and absorption of the ionosphere, and the radio frequency interference (RFI), so far high angular resolution sky intensity map is not available. An interferometer array on lunar orbit provides a perfect observatory in this frequency band: it is out of the ionosphere and the Moon helps to block the RFIs from the Earth. The satellites can make observations on the far side of the Moon and then send back the data on the near side part of the orbit. However, for such array the traditional imaging algorithm is not applicable: the field of view is very wide (almost whole sky), and for baselines distributed on a plane, there is a mirror symmetry between the two sides of the plane. A further complication is that for each baseline, the Moon blocks part of the sky, but as the satellites orbit the Moon, both the direction of the baseline and the blocked sky change, so even imaging algorithms which can deal with non-coplanar baseline may not work in this case. Here we present an imaging algorithm based on solving the linear mapping equations relating the sky intensity to the visibilities. We show that the mirror symmetry can be broken by the three dimensional baseline distribution generated naturally by the precession of the orbital plane of the satellites. The algorithm is applicable and good maps could be reconstructed, even though for each baseline the sky blocking by the Moon is different. We also investigate how the map-making is affected by inhomogeneous baseline distributions.

astro-ph.IM↗

arXiv2017

Simulation and Testing of a Linear Array of Modified Four-Square Feed Antennas for the Tianlai Cylindrical Radio Telescope

A wide bandwidth, dual polarized, modified four-square antenna is presented as a feed antenna for radio astronomical measurements. A linear array of these antennas is used as a line-feed for cylindrical reflectors for Tianlai, a radio interferometer designed for 21~cm intensity mapping. Simulations of the feed antenna beam patterns and scattering parameters are compared to experimental results at multiple frequencies across the 650 - 1420 MHz range. Simulations of the beam patterns of the combined feed array/reflector are presented as well.

astro-ph.IM↗

arXiv2016

Sky reconstruction for the Tianlai cylinder array

In this paper, we apply our sky map reconstruction method for transit type interferometers to the Tianlai cylinder array. The method is based on the spherical harmonic decomposition, and can be applied to cylindrical array as well as dish arrays and we can compute the instrument response, synthesised beam, transfer function and the noise power spectrum. We consider cylinder arrays with feed spacing larger than half wavelength, and as expected, we find that the arrays with regular spacing have grating lobes which produce spurious images in the reconstructed maps. We show that this problem can be overcome, using arrays with different feed spacing on each cylinder. We present the reconstructed maps, and study the performance in terms of noise power spectrum, transfer function and beams for both regular and irregular feed spacing configurations.

astro-ph.IM↗

arXiv2016

Sky reconstruction from transit visibilities: PAON-4 and Tianlai Dish Array

The spherical harmonics $m$-mode decomposition is a powerful sky map reconstruction method suitable for radio interferometers operating in transit mode. It can be applied to various configurations, including dish arrays and cylinders. We describe the computation of the instrument response function, the point spread function (PSF), transfer function, the noise covariance matrix and noise power spectrum. The analysis in this paper is focused on dish arrays operating in transit mode. We show that arrays with regular spacing have more pronounced side lobes as well as structures in their noise power spectrum, compared to arrays with irregular spacing, specially in the north-south direction. A good knowledge of the noise power spectrum $C^{\mathrm{noise}}(\ell)$ is essential for intensity mapping experiments as non uniform $C^{\mathrm{noise}}(\ell)$ is a potential problem for the measurement of the HI power spectrum. Different configurations have been studied to optimise the PAON-4 and Tianlai dish array layouts. We present their expected performance and their sensitivities to the 21-cm emission of the Milky Way and local extragalactic HI clumps

astro-ph.IM↗

arXiv2015

Topology of neutral hydrogen distribution with the Square Kilometer Array

Morphology of the complex HI gas distribution can be quantified by statistics like the Minkowski functionals, and can provide a way to statistically study the large scale structure in the HI maps both at low redshifts, and during the epoch of reionization (EoR). At low redshifts, the 21cm emission traces the underlying matter distribution. Topology of the HI gas distribution, as measured by the genus, could be used as a "standard ruler". This enables the determination of distance-redshift relation and also the discrimination of various models of dark energy and of modified gravity. The topological analysis is also sensitive to certain primordial non-Gaussian features. Compared with two-point statistics, the topological statistics are more robust against the nonlinear gravitational evolution, bias, and redshift-space distortion. The HI intensity map observation naturally avoids the sparse sampling distortion, which is an important systematic in optical galaxy survey. The large cosmic volume accessible to SKA would provide unprecedented accuracy using such a measurement... [abridged]

astro-ph.CO↗

arXiv2014

Spatial Ricci scalar dark energy model

Inspired by holographic principle, we suggest that the density of dark energy is proportional to the spatial Ricci scalar curvature (SRDE). Such model is phenomenologically viable. The best fit values of its parameters at 68% confidence level are found to be: $Ω_{\rm m0}=0.259\pm0.016$ and $α=0.261\pm0.0122$, constrained from the Union+CFA3 sample of 397 SNIa and the BAO measurement. We find the equation of state of SRDE crosses -1 at $z\simeq-0.14$. The present values of the deceleration parameter $q(z)$ for SRDE is found to be $q_{z=0}\sim -0.85$. The phase transition from deceleration to acceleration of the Universe for SRDE occurs at the redshift $z_{q=0}\sim 0.4$. After studying on the perturbation of each component of the Universe, we show that the matter power spectra and cosmic microwave background temperature anisotropy is slightly affected by SRDE, compared with $Λ$CDM.

gr-qc↗

arXiv2014

Cosmological parameter fittings with the BICEP2 data

Combining the latest Planck, Wilkinson Microwave Anisotropy Probe (WMAP), and baryon acoustic oscillation (BAO) data, we exploit the recent cosmic microwave background (CMB) B-mode power spectra data released by the BICEP2 collaboration to constrain the cosmological parameters of the $Λ$CDM model, esp. the primordial power spectra parameters of the scalar and the tensor modes, $n_s,α_s, r, n_t$. We obtained constraints on the parameters for a lensed $Λ$CDM model using the Markov Chain Monte Carlo (MCMC) technique, the marginalized $68\%$ bounds are $r = 0.1043\pm_{0.0914}^{0.0307}$, $n_s = 0.9617\pm_{0.0061}^{ 0.0061}$, $α_s = -0.0175\pm_{0.0097}^{0.0105}$, $n_t = 0.5198\pm_{0.4579}^{0.4515}$. We found that a blue tilt for $n_t$ is favored slightly, but it is still well consistent with flat or even red tilt. Our $r$ value is slightly smaller than the one obtained by the BICEP team, as we allow $n_t$ as a free parameter without imposing the single-field slow roll inflation consistency relation. If we impose this relation, $r=0.2130\pm_{0.0609}^{0.0446}$. For most other parameters, the best fit values and measurement errors are not altered much by the introduction of the BICEP2 data.

astro-ph.CO↗

arXiv2010

Cosmic microwave background with Brans-Dicke Gravity: I. Covariant Formulation

In the covariant cosmological perturbation theory, a 1+3 decomposition ensures that all variables in the frame-independent equations are covariant, gauge-invariant and have clear physical interpretations. We develop this formalism in the case of Brans-Dicke gravity, and apply this method to the calculation of cosmic microwave background (CMB) anisotropy and large scale structures (LSS). We modify the publicly available Boltzmann code CAMB to calculate numerically the evolution of the background and adiabatic perturbations, and obtain the temperature and polarization spectra of the Brans-Dicke theory for both scalar and tensor mode, the tensor mode result for the Brans-Dicke gravity are obtained numerically for the first time. We first present our theoretical formalism in detail, then explicitly describe the techniques used in modifying the CAMB code. These techniques are also very useful to other gravity models. Next we compare the CMB and LSS spectra in Brans-Dicke theory with those in the standard general relativity theory. At last, we investigate the ISW effect and the CMB lensing effect in the Brans-Dicke theory. Constraints on Brans-Dicke model with current observational data is presented in a companion paper (paper II).

astro-ph.CO↗