arXiv subjects

Francesco Bonaccorso

Publications and source records attributed to Francesco Bonaccorso.

At least 19 recordsLinked to original sources

arXiv2026

Scalable Conformal MoSx Catalyst for Efficient Hydrogen Evolution at Industrial-Level Current Density in Alkaline Electrolyzers

The development of simple and scalable fabrication strategies for cost-effective electrodes is crucial to advance water splitting in alkaline water electrolyzers (AWEs). Here, we present a coating-annealing method to conformally coat a MoSx catalyst layer onto a porous Ni foam (NF) substrate. By controlling the annealing process, the composition of the MoSx layer could be tuned from MoS2 to MoS3 and its catalytic performance for hydrogen evolution reaction (HER) in alkaline media was optimized. The MoS3@NF synthesized by this method achieved industrially relevant HER current densities of 200 mA/cm2 at a low overpotential of 246 mV, maintaining stable operation for over 240 h. The MoS3@NF cathode, combined with a stainless steel anode, enabled an alkaline water electrolyzer (AWE) cell to operate steadily at 1.96 V and 1 A/cm2 for 1000 h. This performance surpasses that of most of the previously reported water electrolyzers employing MoSx-based cathodes. Our work demonstrates the potential of MoS3 (with its abundant edge-sulfur atoms serving as active sites) as a high-performance cathode material for industrial AWEs.

cond-mat.mtrl-sci↗

arXiv2026

Permanent Lattice Compression of Lead-Halide Perovskite for Persistently Enhanced Optoelectronic Properties

Under mild mechanical pressure, halide perovskites show enhanced optoelectronic properties. However, these improvements are reversible upon decompression, and permanent enhancements have yet to be realized. Here, we report antisolvent-assisted solvent acidolysis crystallization that enables us to prepare methylammonium lead bromide single crystals showing intense emission at all four edges under ultraviolet light excitation. We study structural variations, edge-vs-center, in these crystals using micro-X-ray diffraction and find that the enhanced emission at the edges correlates with lattice compression compared to in the central areas. Time-resolved photoluminescence measurements show much longer-lived photogenerated carriers at the compressed edges, with radiative component lifetimes of ca. 1.4 us, 10 times longer than at the central regions. The properties of the edges are exploited to fabricate planar photodetectors exhibiting detectivities of 3x10^13 Jones, compared to 5x10^12 Jones at the central regions. The enhanced lifetimes and detectivities correlate to the reduced trap state densities and the formation of shallower traps at the edges due to lattice compression.

cond-mat.mtrl-sci↗

arXiv2026

Phase Transitions in Low-Dimensional Layered Double Perovskites: The Role of the Organic Moieties

Halide double perovskites are an interesting alternative to Pb-containing counterparts as active materials in optoelectronic devices. Low-dimensional double perovskites are fabricated by introducing large organic cations, resulting in organic/inorganic architectures with one or more inorganic octahedral layers separated by organic cations. Here, we synthesize layered double perovskites based on 3D Cs2AgBiBr6 that consist of double (2L) or single (1L) inorganic octahedral layers, using ammonium cations of different size and chemical structure. Temperature-dependent Raman spectroscopy reveals phase transition signatures in both inorganic lattice and organic moieties by detecting variations in their vibrational modes. Changes in the conformational arrangement of the organic cations to an ordered state coincide with a phase transition in the 1L systems with the shortest ammonium moieties. Significant changes of photoluminescence intensity observed around the transition temperature suggest that optical properties may be deeply affected by the octahedral tilts emerging at the phase transition.

cond-mat.mtrl-sci↗

arXiv2025

2D Hexagonal Boron Nitride-based Anticorrosion Coatings

The corrosion of metallic surfaces poses significant challenges across industries such as petroleum, energy, and biomedical sectors, leading to structural degradation, safety risks, and substantial maintenance costs. Traditional organic and metallic coatings provide some protection, but their limited durability and susceptibility to harsh environmental conditions necessitate the development of more advanced and efficient solutions. This has driven significant interest in two-dimensional (2D) materials, with graphene extensively studied for its exceptional mechanical strength and impermeability to gases and ions. However, while graphene offers short-term corrosion protection, its high electrical conductivity presents a long-term issue by promoting galvanic corrosion on metal surfaces. In contrast, hexagonal boron nitride (h-BN) has emerged as a promising alternative for anticorrosion coatings. h-BN combines exceptional chemical stability, impermeability, and electrical insulation, making it particularly suited for long-term protection in highly corrosive or high-temperature environments. While h-BN holds promise as anticorrosion material, challenges such as structural defects, agglomeration of nanosheets, and poor dispersion within coatings limit its performance. This review provides a comprehensive analysis of recent advancements in addressing these challenges, including novel functionalization strategies, scalable synthesis methods, and hybrid systems that integrate h-BN with complementary materials. By bridging the gap between fundamental research and industrial applications, this review outlines the potential for h-BN to revolutionize anticorrosion technologies. These obstacles necessitate advanced strategies such as surface functionalization to improve compatibility with polymer matrices and dispersion optimization to minimize agglomeration.

cond-mat.mtrl-sci↗

arXiv2021

Graphene-Based Electrodes in a Vanadium Redox Flow Battery Produced by Rapid Low-Pressure Combined Gas Plasma Treatments

The development of high-power density vanadium redox flow batteries (VRFBs) with high energy efficiencies (EEs) is crucial for the widespread dissemination of this energy storage technology. In this work, we report the production of novel hierarchical carbonaceous nanomaterials for VRFB electrodes with high catalytic activity toward the vanadium redox reactions (VO2+/VO2+ and V2+/V3+). The electrode materials are produced through a rapid (minute timescale) low-pressure combined gas plasma treatment of graphite felts (GFs) in an inductively coupled radio frequency reactor. By systematically studying the effects of either pure gases (O2 and N2) or their combination at different gas plasma pressures, the electrodes are optimized to reduce their kinetic polarization for the VRFB redox reactions. To further enhance the catalytic surface area of the electrodes, single-/few-layer graphene, produced by highly scalable wet-jet milling exfoliation of graphite, is incorporated into the GFs through an infiltration method in the presence of a polymeric binder. Depending on the thickness of the proton-exchange membrane (Nafion 115 or Nafion XL), our optimized VRFB configurations can efficiently operate within a wide range of charge/discharge current densities, exhibiting energy efficiencies up to 93.9%, 90.8%, 88.3%, 85.6%, 77.6%, and 69.5% at 25, 50, 75, 100, 200, and 300 mA cm-2, respectively. Our technology is cost-competitive when compared to commercial ones (additional electrode costs < 100 euro m-2) and shows EEs rivalling the record-high values reported for efficient systems to date. Our work remarks on the importance to study modified plasma conditions or plasma methods alternative to those reported previously (e.g., atmospheric plasmas) to improve further the electrode performances of the current VRFB systems.

physics.app-ph↗

arXiv2021

Two-Dimensional Gallium Sulfide Nanoflakes for UV-Selective Photoelectrochemical-type Photodetectors

Two-dimensional (2D) transition-metal monochalcogenides have been recently predicted to be potential photo(electro)catalysts for water splitting and photoelectrochemical (PEC) reactions. Differently from the most established InSe, GaSe, GeSe, and many other monochalcogenides, bulk GaS has a large band gap of ca. 2.5 eV, which increases up to more than 3.0 eV with decreasing its thickness due to quantum confinement effects. Therefore, 2D GaS fills the void between 2D small-band-gap semiconductors and insulators, resulting of interest for the realization of van der Waals type-I heterojunctions in photocatalysis, as well as the development of UV light-emitting diodes, quantum wells, and other optoelectronic devices. Based on theoretical calculations of the electronic structure of GaS as a function of layer number reported in the literature, we experimentally demonstrate, for the first time, the PEC properties of liquid-phase exfoliated GaS nanoflakes. Our results indicate that solution-processed 2D GaS-based PEC-type photodetectors outperform the corresponding solid-state photodetectors. In fact, the 2D morphology of the GaS flakes intrinsically minimizes the distance between the photogenerated charges and the surface area at which the redox reactions occur, limiting electron-hole recombination losses. The latter are instead deleterious for standard solid-state configurations. Consequently, PEC-type 2D GaS photodetectors display a relevant UV-selective photoresponse. In particular, they attain responsivities of 1.8 mA W-1 in 1 M H2SO4 (at 0.8 V vs reversible hydrogen electrode -RHE-), 4.6 mA W-1 in 1 M Na2SO4 (at 0.9 V vs RHE), and 6.8 mA W-1 in 1 M KOH (at 1.1 V vs RHE) under 275 nm illumination wavelength with an intensity of 1.3 mW cm-2.

physics.app-ph↗

arXiv2021

Solution-processed two-dimensional materials for next-generation photovoltaics

In the ever-increasing energy demand scenario, the development of novel photovoltaic (PV) technologies is considered to be one of the key solutions to fulfil the energy request. In this context, graphene and related two-dimensional (2D) materials (GRMs), including nonlayered 2D materials and 2D perovskites, as well as their hybrid systems, are emerging as promising candidates to drive innovation in PV technologies. The mechanical, thermal, and optoelectronic properties of GRMs can be exploited in different active components of solar cells to design next-generation devices. These components include front (transparent) and back conductive electrodes, charge transporting layers, and interconnecting-recombination layers, as well as photoactive layers. The production and processing of GRMs in the liquid phase, coupled with the ability to on-demand tune their optoelectronic properties exploiting wet-chemical functionalization, enable their effective integration in advanced PV devices through scalable, reliable, and inexpensive printing-coating processes. Herein, we review the progresses in the use of solution-processed 2D materials in organic solar cells, dye-sensitized solar cells, perovskite solar cells, quantum dot solar cells, and organic-inorganic hybrid solar cells, as well as in tandem systems. We first provide a brief introduction on the properties of 2D materials and their production methods by solution-processing routes. Then, we discuss the functionality of 2D materials for electrodes, photoactive layer components-additives, charge transporting layers, and interconnecting layers through figures of merit, which allow the performance of solar cells to be determined and compared with the state-of-the-art values. We finally outline the roadmap for the further exploitation of solution-processed 2D materials to boost the performance of PV devices.

physics.app-ph↗

arXiv2021

Nitrogen-doped graphene based triboelectric nanogenerators

Harvesting all sources of available clean energy is an essential strategy to contribute to healing current dependence on non-sustainable energy sources. Recently, triboelectric nanogenerators (TENGs) have gained visibility as new mechanical energy harvester offering a valid alternative to batteries, being particularly suitable for portable devices. Here, the increased capacitance of a few-layer graphene-based electrode is obtained by incorporating nitrogen-doped graphene (N_graphene), enabling a 3_fold enhancement in TENGs power output. The dependence of TENGs performance on the electronic properties of different N_graphene types, varying in the doping concentration and in the relative content of N-pyridinic and N-graphitic sites is investigated. These sites have different electron affinities, and synergistically contribute to the variation of the capacitive and resistive properties of N-graphene and consequently, TENG performance. It is demonstrated that the power enhancement of the TENG occurs when the N_graphene, an n-semiconductor, is interfaced between the positive triboelectric material and the electrode, while a deterioration of the electrical performance is observed when it is placed at the interface with the negative triboelectric material. This behavior is explained in terms of the dependence of N_graphene quantum capacitance on the electrode chemical potential which shifts according to the opposite polarization induced at the two electrodes upon triboelectrification.

physics.app-ph↗

arXiv2020

Anisotropic layer-by-layer carbon nanotubes/boron nitride/rubber composite and its application in electromagnetic shielding

Multifunctional polymer composites with anisotropic properties are attracting interests as they fulfil the growing demand of multitasking materials. In this work, anisotropic polymer composites are fabricated by combining the layer-by-layer (LBL) filtration method with the alternative assembling of carbon nanotubes (CNTs) and hexagonal boron nitride flakes (hBN) on natural rubber latex particles (NR). The layered composites exhibit anisotropic thermal and electrical conductivities, which are tailored through the layer formulations. The best composite consists of four layers of NR modified with 8 phr (parts per Hundred Rubber) CNTs (~7.4 wt%) and four alternated layers with 12 phr hBN (~10.7 wt%). The composites exhibit an electromagnetic interference (EMI) shielding effectiveness of 22.41+-0.14 dB mm-1 at 10.3 GHz and a thermal conductivity equal to 0.25 W/(mK). Furthermore, when the layered composite is used as an electrical thermal heater the surface reaches a stable temperature of ~103 C in approx. 2 min, with an input bias of 2.5 V.

cond-mat.mtrl-sci↗

arXiv2020

Scalable spray-coated graphene-based electrodes for high-power electrochemical double-layer capacitors operating over a wide range of temperature

Advancements in electrochemical double-layer capacitor (EDLC) technology require the concomitant use of novel efficient electrode materials and viable electrode manufacturing methods. Cost-effectiveness, scalability and sustainability are key-drivers for fulfilling product development chain accepted by worldwide legislations. Herein, we report a scalable and sprayable "green" electrode material-based ink based on activated carbon and single-/few-layer graphene (SLG/FLG) flakes. We show that, contrary to commercial reduced graphene oxide, defect-free and flat SLG/FLG flakes reduce the friction of ions over the electrode films, while spray coating deposition of our ink maximises the electrolyte accessibility to the electrode surface area. Sprayed SLG/FLG flakes-based EDLCs display superior rate capability performance (e.g., specific energies of 31.5, 23.7 and 12.5 Wh kg-1 at specific powers of 150, 7500 and 30000 W kg-1, respectively) compared to both SLG/FLG flakes-free devices and commercial-like EDLCs produced by slurry-coating method. The use of SLG/FLG flakes enables our sprayed EDLCs to operate in a wide range of temperature (-40/+100°C) compatible with ionic liquid/organic solvent-based electrolytes, overcoming the specific power limits of AC-based EDLCs. A prototype EDLCs stack consisting of multiple large-area EDLCs, each one displaying a capacitance of 25 F, demonstrates the industrial potential of our technology.

physics.app-ph↗

arXiv2020

Solution-processed GaSe nanoflake-based films for photoelectrochemical water splitting and photoelectrochemical-type photodetectors

Gallium selenide (GaSe) is a layered compound, which has been exploited in nonlinear optical applications and photodetectors due to its anisotropic structure and pseudo-direct optical gap. Theoretical studies predicted that its two-dimensional (2D) form is a potential photocatalyst for water splitting reactions. Herein, we first report the photoelectrochemical (PEC) characterization of GaSe nanoflakes (single-/few-layer flakes), produced via liquid phase exfoliation, for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in both acidic and alkaline media. In 0.5 M H2SO4, the GaSe photoelectrodes display the best PEC performance, i.e. a ratiometric power-saved metric for HER (Φsaved,HER) of 0.09% and a ratiometric power-saved metric for OER (Φsaved,OER) of 0.25%. When used as PEC-type photodetectors, GaSe photoelectrodes show a responsivity of ~0.16 A W-1 upon 455 nm illumination at light intensity of 63.5 uW cm-2 and applied potential of -0.3 V vs. reversible hydrogen electrode (RHE). The stability analysis of the GaSe photodetectors evidences a durable operation over tens of cathodic linear sweep voltammetry scans in 0.5 M H2SO4 for HER. Viceversa, degradation effects have been observed in both alkaline and anodic operation due to highly oxidizing environment and O2-induced (photo-)oxidation effects. Our results provide new insight into PEC properties of GaSe nanoflakes for their exploitation in photoelectrocatalysis, PEC-type photodetectors and (bio)sensors.

physics.app-ph↗

arXiv2020

Flexible Graphene/Carbon Nanotube Electrochemical Double-Layer Capacitors with Ultrahigh Areal Performance

The fabrication of electrochemical double-layer capacitors (EDLCs) with high areal capacitance relies on the use of elevated mass loadings of highly porous active materials. Herein, we demonstrate a high-throughput manufacturing of graphene/nanotubes hybrid EDLCs. Wet-jet milling (WJM) method is exploited to exfoliate the graphite into single/few-layer graphene flakes (WJM-G) in industrial volume (production rate ~0.5 kg/day). Commercial single/double walled carbon nanotubes (SDWCNTs) are mixed with graphene flakes in order to act as spacers between the graphene flakes during their film formation. The latter is obtained by one-step vacuum filtration, resulting in self-standing, metal- and binder-free flexible EDLC electrodes with high active material mass loadings up to 30 mg cm-2. The corresponding symmetric WJM-G/SDWCNTs EDLCs exhibit electrode energy densities of 539 uWh cm-2 at 1.3 mW cm-2 and operating power densities up to 532 mW cm-2 (outperforming most of the EDLC technologies). The EDCLs show excellent cycling stability and outstanding flexibility even under highly folded states (up to 180 degrees). The combination of industrial-like production of active materials, simplified manufacturing of EDLC electrodes, and ultrahigh areal performance of the as-produced EDLCs are promising for novel advanced EDLC designs.

physics.app-ph↗

arXiv2020

Extending the colloidal transition metal dichalcogenide library to ReS2 nanosheets for application in gas sensing and electrocatalysis

Among the large family of transition metal dichalcogenides (TMDCs), recently ReS2 has stood out due to its nearly layer-independent optoelectronic and physicochemical properties. These are related to its 1T distorted octahedral structure, which leads to strong in-plane anisotropy and the presence of active sites at its surface, which makes ReS2 interesting for applications such as gas sensors and catalysts for H2 production. However, the current fabrication methods for ReS2 use chemical or physical vapor deposition (CVD or PVD) processes that are costly and involve complex and lengthy fabrication procedures, therefore limiting their large-scale production and exploitation. To address this issue, we developed a colloidal synthesis approach, which allows the production of ReS2 to be attained at temperatures below 360 Celsius degrees and with reaction times < 2 h, resulting in a more cost-efficient strategy than the CVD and PVD methods. By combining the solution-based synthesis with surface functionalization strategies, we demonstrate the feasibility of colloidal ReS2 nanosheet films for gas sensing of different toxic gases, moisture and other volatile compounds with highly competitive performance in comparison with devices built with CVD-grown ReS2 and MoS2. In addition, the integration of the ReS2 nanosheet films in assemblies, in which they are deposited on top of networks of carbon nanotubes, allowed us to fabricate electrodes for electrocatalysis for H2 production in both acid and alkaline conditions. Results from proof-of-principle devices show an electrocatalytic overpotential that is competitive with devices based on ReS2 produced by CVD, and even with MoS2, WS2 and MoSe2 electrocatalysts.

physics.app-ph↗

arXiv2020

Octapod-shaped CdSe nanocrystals hosting Pt with high-mass activity for the hydrogen evolution reaction

The design of efficient electrocatalysts for electrochemical water splitting with minimal amount of precious metal is crucial to attain renewable and sustainable energy conversion. Here, we report the use of a network of CdSe branched colloidal nanocrystals, made of a CdSe core and eight CdSe pods (so-called octapods), able to host on their pods Pt particles, and thus catalyzing water splitting reactions. Thanks to the octapod shape, the resulting Pt-hosting network is mechanically trapped onto carbon nanotube buckypaper, providing mechanically flexible and binder-free electrodes. We found that such hierarchical configuration maximizes the mass activity and the utilization efficiency of Pt for the hydrogen evolution reaction (HER). At a potential of -0.15 V vs. reversible hydrogen electrode, the Pt/octapod network-based electrodes display a Pt mass activity on the HER of 166 A mg-1 and 42 A mg-1 in acidic and alkaline media, respectively. These values correspond to turnover frequencies of 168 s-1 and 42 s-1, respectively, which are in that order 14 and 21 times higher compared to commercially available Pt/C benchmarks. The strong chemical and mechanical interactions between the Pt and the octapod surface, along with pod-aided adhesion of the Pt/octapod network to the buckypaper, result in a long-term durability (>20 h) of the HER-activity in both media. These results experimentally prove that the exploitation of our network of branched nanocrystals hosting Pt particles can circumvent the durability issues of the catalysts while adopting either ultralow Pt loadings or benchmarking carbon-supported Pt nanocrystals. Our work opens up prospects for using porous networks made by branched nanocrystals as catalysts with ultralow amount of noble metals and controlled catalytic properties.

physics.chem-ph↗

arXiv2020

Single-step exfoliation and functionalization of few-layers black phosphorus and its application for polymer composites

We demonstrate the large scale exfoliation of bulk black phosphorus into few-layers black phosphorus. We use wet-jet mill (WJM) as an industrially scalable exfoliation technique. In order to avoid the degradation by oxidation of the exfoliated flakes, the few-layers black phosphorus is protected by functionalisation (with 4-bromobenzene-diazonium tetrafluoroborate) during the exfoliation process. We used the exfoliated and functionalised flakes as fillers in a polymethyl methacrylate matrix to test the mechanical endurance, obtaining an improvement in the Young modulus of 106% compared to the bare polymer. These data support the development of black phosphorus materials as 2D-polymer fillers and performance-enhancers.

physics.app-ph↗

arXiv2020

Niobium disulphide (NbS$_2$)-based (heterogeneous) electrocatalysts for an efficient hydrogen evolution reaction

The design of efficient and cost-effective catalysts for the hydrogen evolution reaction (HER) is the key for molecular hydrogen (H2) production from electrochemical water splitting. Transition metal dichalcogenides (MX2), most notably group-6 MX2 (e.g., MoS2 and WS2), are appealing catalysts for the HER alternative to the best, but highly expensive, Pt-group elements. However, their HER activity is typically restricted to their edge sites rather than their basal plane. Furthermore, their semiconducting properties hinder an efficient electron transfer to the catalytic sites, which impedes a high rate of H2 production. Herein, we exploit liquid-phase exfoliation-produced metallic (1H, 2H and 3R) NbS2 nanoflakes, belonging to the class of metallic layered group-5 MX2, to overcome the abovementioned limitations. Both chemical treatment with hygroscopic Li salt and electrochemical in operando self-nanostructuring are exploited to improve the NbS2 nanoflake HER activity. The combination of NbS2 with other MX2, in our case MoSe2, also provides heterogeneous catalysts accelerating the HER kinetics of the individual counterparts. The designed NbS2-based catalysts exhibit an overpotential at a cathodic current of 10 mA cm-2 (n10) as low as 0.10 and 0.22 V vs. RHE in 0.5 M H2SO4 and 1 M KOH, respectively. In 0.5 M H2SO4, the HER activity of the NbS2-based catalysts is also superior to those of the Pt/C benchmark at current densities higher than 80 mA cm-2. Our work provides general guidelines for a scalable and cost-effective exploitation of NbS2, as well as the entire MX2 portfolio, for attaining a viable H2 production through electrochemical routes.

physics.chem-ph↗

arXiv2019

CVD-graphene/graphene flakes dual-films as advanced DSSC counter electrodes

The use of graphene-based electrodes is burgeoning in a wide range of applications, including solar cells, light emitting diodes, touch screens, field-effect transistors, photodetectors, sensors and energy storage systems. The success of such electrodes strongly depends on the implementation of effective production and processing methods for graphene. In this work, we take advantage of two different graphene production methods to design an advanced, conductive oxide- and platinum-free, graphene-based counter electrode for dye-sensitized solar cells (DSSCs). In particular, we exploit the combination of a graphene film, produced by chemical vapor deposition (CVD) (CVD-graphene), with few-layer graphene (FLG) flakes, produced by liquid phase exfoliation. The CVD-graphene is used as charge collector, while the FLG flakes, deposited atop by spray coating, act as catalyst for the reduction of the electrolyte redox couple (i.e., I3-/I-- and Co+2/+3). The as-produced counter electrodes are tested in both I3-/I-- and Co+2/+3-based semitransparent DSSCs, showing power conversion efficiencies of 2.1% and 5.09%, respectively, under 1 SUN illumination. At 0.1 SUN, Co+2/+3-based DSSCs achieve a power conversion efficiency as high as 6.87%. Our results demonstrate that the electrical, optical, chemical and catalytic properties of graphene-based dual films, designed by combining CVD-graphene and FLG flakes, are effective alternatives to FTO/Pt counter electrodes for DSSCs for both outdoor and indoor applications.

physics.app-ph↗

arXiv2019

Engineered MoSe2-based heterostructures for efficient electrochemical hydrogen evolution reaction

Two-dimensional transition metal-dichalcogenides are emerging as efficient and cost-effective electrocatalysts for hydrogen evolution reaction (HER). However, only the edge sites of their trigonal prismatic phase show HER-electrocatalytic properties, while the basal plane, which is absent of defective/unsaturated sites, is inactive. Here, we tackle the key challenge that is increasing the number of electrocatalytic sites by designing and engineering heterostructures composed of single-/few-layer MoSe2 flakes and carbon nanomaterials (graphene or single-wall carbon nanotubes (SWNTs)) produced by solution processing. The electrochemical coupling between the materials that comprise the heterostructure effectively enhances the HER-electrocatalytic activity of the native MoSe2 flakes. The optimization of the mass loading of MoSe2 flakes and their electrode assembly via monolithic heterostructure stacking provided a cathodic current density of 10mAcm-2 at overpotential of 100mV, a Tafel slope of 63mVdec-1 and an exchange current density (j0) of 0.203 Acm-2. In addition, electrode thermal annealing in a hydrogen environment and chemical bathing in n-butyllithium are exploited to texturize the basal planes of the MoSe2 flakes (through Se-vacancies creation) and to achieve in situ semiconducting-to-metallic phase conversion, respectively, thus they activate new HER-electrocatalytic sites. The as-engineered electrodes show a 4.8-fold enhancement of j0 and a decrease in the Tafel slope to 54mVdec-1.

cond-mat.mtrl-sci↗