arXiv subjects

Günter Reiss

Publications and source records attributed to Günter Reiss.

At least 55 records · Page 3Linked to original sources

arXiv2014

Towards wafer scale inductive characterization of spin transfer torque critical current density of magnetic tunnel junction stacks

We explore the prospects of wafer scale inductive probing of the critical current density $j^{c0}$ for spin transfer torque switching of a CoFeB/MgO/CoFeB magnetic tunnel junction with varying MgO thickness. From inductive measurements magnetostatic parameters and the effective damping are derived and $j^{c0}$ is calculated based on spin transfer torque equations. The inductive values compare well to the values derived from current induced switching measurements on individual nanopillars. Using a wafer scale inductive probe head could in the future enable wafer probe station based metrology of $j^{c0}$.

cond-mat.mtrl-sci↗

arXiv2014

Tunneling magnetoresistance devices based on topological insulators: Ferromagnet/insulator/topological-insulator junctions employing Bi$_{2}$Se$_{3}$

We theoretically investigate tunneling magnetoresistance (TMR) devices, which are probing the spin-momentum coupled nature of surface states of the three-dimensional topological insulator Bi$_{2}$Se$_{3}$. Theoretical calculations are performed based on a realistic tight-binding model for Bi$_{2}$Se$_{3}$. We study both three dimensional devices, which exploit the surface states of Bi$_{2}$Se$_{3}$, as well as two-dimensional devices, which exploit the edge states of thin Bi$_{2}$Se$_{3}$ strips. We demonstrate that the material properties of Bi$_{2}$Se$_{3}$ allow a TMR ratio at room temperature of the order of 1000%. Analytical formulas are derived that allow a quick estimate of the achievable TMR ratio in these devices. The devices can be used to measure the spin polarization of the topological surface states as an alternative to spin-ARPES. Unlike TMR devices based on magnetic tunnel junctions the present devices avoid the use of a second ferromagnetic electrode whose magnetization needs to be pinned.

cond-mat.mes-hall↗

arXiv2014

On/off switching of bit readout in bias-enhanced tunnel magneto-Seebeck effect

Thermoelectric effects in magnetic tunnel junctions are currently an attractive research topic. Here, we demonstrate that the tunnel magneto-Seebeck effect (TMS) in CoFeB/MgO/CoFeB tunnel junctions can be switched on to a logic 1 state and off to 0 by simply changing the magnetic state of the CoFeB electrodes. We enable this new functionality of magnetic tunnel junctions by combining a thermal gradient and an electric field. This new technique unveils the bias-enhanced tunnel magneto-Seebeck effect, which can serve as the basis for logic devices or memories in a green information technology with a pure thermal write and read process. Furthermore, the thermally generated voltages that are referred to as the Seebeck effect are well known to sensitively depend on the electronic structure and therefore have been valued in solid-state physics for nearly one hundred years. Here, we lift Seebeck's historic discovery from 1821 to a new level of current spintronics. Our results show that the signal crosses zero and can be adjusted by tuning a bias voltage that is applied between the electrodes of the junction; hence, the name of the effect is bias-enhanced tunnel magneto-Seebeck effect (bTMS). Via the spin- and energy-dependent transmission of electrons in the junction, the bTMS effect can be configured using the bias voltage with much higher control than the tunnel magnetoresistance (TMR) and even completely suppressed for only one magnetic configuration, which is either parallel (P) or anti-parallel (AP). This option allows a readout contrast for the magnetic information of -3000% at room temperature while maintaining a large signal for one magnetic orientation. This contrast is much larger than the value that can be obtained using the TMR effect. Moreover, our measurements are a step towards the experimental realization of high TMS ratios, which are predicted for specific Co-Fe compositions.

cond-mat.mes-hall↗

arXiv2014

Experimental realization of a semiconducting full Heusler compound: Fe2TiSi

Single-phase films of the full Heusler compound Fe2TiSi have been prepared by magnetron sputtering. The compound is found to be a semiconductor with a gap of 0.4eV. The electrical resistivity has a logarithmic temperature dependence up to room temperature due to Kondo scattering of a dilute free electron gas off superparamagnetic impurities. The origin of the electron gas is extrinsic due to disorder or off-stoichiometry. Density functional theory calculations of the electronic structure are in excellent agreement with electron energy loss, optical, and x-ray absorption experiments. Fe2TiSi may find applications as a thermoelectric material.

cond-mat.mtrl-sci↗

arXiv2014

Multiple phases in sputtered Cr2CoGa films

By magnetron co-sputtering, thin films of a nominal Cr2CoGa compound were deposited on MgO and MgAl2O4. To achieve crystallisation in the inverse Heusler structure, different heat treatments were tested. Instead of the inverse Heusler structure, we observed phase separation and precipitate formation in dependence on the heat treatment. The main precipitate is Cr3Ga in A15 structure. The remainder forms Co-rich CoGa in the B2 structure and possibly Cr-rich CoCr in the sigma-phase.

cond-mat.mtrl-sci↗

arXiv2014

Phase separation in Fe2CrSi thin films

Thin films of a nominal Fe2CrSi alloy have been deposited by magnetron co-sputtering with various heat treatments on MgO and MgAl2O4 substrates. After heat treatment, the films were found to decompose into a nearly epitaxial Fe3Si film with the D0$_3$ structure and Cr3Si precipitates with the A15 structure. We explain the experimental results on the basis of ab initio calculations, which reveal that this decomposition is energetically highly favorable.

cond-mat.mtrl-sci↗

arXiv2013

Unusual angular dependence of tunneling magneto-Seebeck effect

We find an unusual angular dependence of the tunneling magneto-Seebeck effect (TMS). The conductance shows normally a cosine-dependence with the angle between the magnetizations of the two ferromagnetic leads. In contrast, the angular dependence of the TMS depends strongly on the tunneling magneto resistance (TMR) ratio. For small TMR ratios we obtain also a cosine-dependence whereas for very large TMR ratios the angular dependence approaches a step-like function.

cond-mat.mes-hall↗

arXiv2013

Influence of heat flow directions on Nernst effects in Py/Pt bilayers

We investigated the voltages obtained in a thin Pt strip on a Permalloy film which was subject to in-plane temperature gradients and magnetic fields. The voltages detected by thin W-tips or bond wires showed a purely symmetric effect with respect to the external magnetic field which can be fully explained by the planar Nernst effect (PNE). To verify the influence of the contacts measurements in vacuum and atmosphere were compared and gave similar results. We explain that a slightly in-plane tilted temperature gradient only shifts the field direction dependence but does not cancel out the observed effects. Additionally, the anomalous Nernst effect (ANE) could be induced by using thick Au-tips which generated a heat current perpendicular to the sample plane. The effect can be manipulated by varying the temperature of the Au-tips. These measurements are discussed concerning their relevance in transverse spin Seebeck effect measurements.

cond-mat.mtrl-sci↗

arXiv2013

Electronic structure and optical band gap determination of NiFe2O4

In a theoretical study we investigate the electronic structure and the band gap of the inverse spinel ferrite NiFe2O4. The experimental optical absorption spectrum is accurately reproduced by fitting the Tran-Blaha parameter in the modified Becke-Johnson potential. The accuracy of the commonly applied Tauc plot to find the optical gap is assessed based on the computed spectra and we find that this approach can lead to a misinterpretation of the experimental data. The minimum gap of NiFe2O4 is found to be a 1.53eV wide indirect gap, which is located in the minority spin channel.

cond-mat.str-el↗

arXiv2013

High TMR ratio in Co2FeSi and Fe2CoSi based magnetic tunnel junctions

Magnetic tunnel junctions with Fe1+xCo2-xSi (0 < x < 1) electrodes and MgO barrier were prepared on MgO substrates by magnetron co-sputtering. Maximum tunnel magnetoresistance (TMR) ratios of 262 % at 15 K and 159 % at room temperature were observed for x=0.75. Correlations of the annealing temperature dependent atomic ordering and TMR amplitude are discussed. The high TMR for an intermediate stoichiometry is ascribed to the adjustment of the Fermi energy within a minority spin pseudo gap.

cond-mat.mtrl-sci↗

arXiv2013

Time-resolved measurement of the tunnel magneto-Seebeck effect in a single magnetic tunnel junction

Recently, several groups have reported spin-dependent thermoelectric effects in magnetic tunnel junctions. In this paper, we present a setup for time-resolved measurements of thermovoltages and thermocurrents of a single micro- to nanometer-scaled tunnel junction. An electrically modulated diode laser is used to create a temperature gradient across the tunnel junction layer stack. This laser modulation technique enables the recording of time-dependent thermovoltage signals with a temporal resolution only limited by the preamplifier for the thermovoltage. So far, time-dependent thermovoltage could not be interpreted. Now, with the setup presented in this paper, it is possible to distinguish different Seebeck voltage contributions to the overall measured voltage signal in the μs time regime. A model circuit is developed that explains those voltage contributions on different sample types. Further, it will be shown that a voltage signal arising from the magnetic tunnel junction can only be observed when the laser spot is directly centered on top of the magnetic tunnel junction, which allows a lateral separation of the effects.

cond-mat.mes-hall↗

arXiv2013

X-ray absorption spectroscopy and magnetic circular dichroism studies of L1_0-Mn-Ga thin films

Tetragonally distorted $\rm{Mn}_{3-x}\rm{Ga}_x$ thin films with $0.1< x < 2$ show a strong perpendicular magnetic anisotropy and low magnetization and thus have the potential to serve as electrodes in spin transfer torque magnetic random access memory. Because a direct capping of these films with MgO is problematic due to oxide formation, we examined the influence of a CoFeB interlayer, and of two different deposition methods for the MgO barrier on the formation of interfacial MnO for $\rm{Mn}_{62}\rm{Ga}_{38}$ by element specific X-ray absorption spectroscopy (XAS) and magnetic circular dichroism (XMCD). A highly textured L1$_0$ crystal structure of the Mn-Ga films was verified by X-ray diffraction (XRD) measurements. For samples with e-beam evaporated MgO barrier no evidence for MnO was found, whereas in samples with magnetron sputtered MgO MnO was detected, even for the thickest interlayer thickness. Both XAS and XMCD measurements showed an increasing interfacial MnO amount with decreasing CoFeB interlayer thickness. Additional element specific full hysteresis loops determined an out-of-plane magnetization axis for the Mn and Co, respectively.

cond-mat.mtrl-sci↗

arXiv2013

Backhopping effect in magnetic tunnel junctions: comparison between theory and experiment

We report on the magnetic switching and backhopping effects due to spin-transfer-torque in magnetic tunnel junctions. Experimental data on the current-induced switching in junctions with MgO tunnel barrier reveal a random back-and-forth switching between the magnetization states, which appears when the current direction favors the parallel magnetic configuration. The effect depends on the barrier thickness $t_b$, and is not observed in tunnel junctions with very thin MgO tunnel barriers, $t_b$ $<$ 0.95 nm. Switching dependence on the bias voltage and barrier thickness is explained in terms of the macrospin model, with the magnetization dynamics described by the modified Landau-Lifshitz-Gilbert equation. Numerical simulations indicate that the competition between in-plane and out-of-plane torque components can result at high bias voltages in a non-deterministic switching behavior, in agreement with experimental observations. When the barrier thickness is reduced, the overall coupling between the magnetic layers across the barrier becomes ferromagnetic, which suppresses the backhopping effect.

cond-mat.mtrl-sci↗

arXiv2013

Quantitative study of the spin Hall magnetoresistance in ferromagnetic insulator/normal metal hybrids

We experimentally investigate and quantitatively analyze the spin Hall magnetoresistance effect in ferromagnetic insulator/platinum and ferromagnetic insulator/nonferromagnetic metal/platinum hybrid structures. For the ferromagnetic insulator we use either yttrium iron garnet, nickel ferrite or magnetite and for the nonferromagnet copper or gold. The spin Hall magnetoresistance effect is theoretically ascribed to the combined action of spin Hall and inverse spin Hall effect in the platinum metal top layer. It therefore should characteristically depend upon the orientation of the magnetization in the adjacent ferromagnet, and prevail even if an additional, nonferromagnetic metal layer is inserted between Pt and the ferromagnet. Our experimental data corroborate these theoretical conjectures. Using the spin Hall magnetoresistance theory to analyze our data, we extract the spin Hall angle and the spin diffusion length in platinum. For a spin mixing conductance of $4\times10^{14}\;\mathrm{Ω^{-1}m^{-2}}$ we obtain a spin Hall angle of $0.11\pm0.08$ and a spin diffusion length of $(1.5\pm0.5)\;\mathrm{nm}$ for Pt in our thin film samples.

cond-mat.mes-hall↗

arXiv2013

Tunneling magneto thermocurrent in CoFeB/MgO/CoFeB based magnetic tunnel junctions

We study the tunneling magneto thermopower and tunneling magneto thermocurrent of CoFeB/MgO/CoFeB magnetic tunnel junctions (MTJ). The devices show a clear change of the thermoelectric properties upon reversal of the magnetisation of the CoFeB layers from parallel to the antiparallel orientation. When switching from parallel to antiparallel the thermopower increases by up to 55% where as the thermocurrent drops by 45%. These observations can be well explained by the Onsager relations taking into account the tunneling magneto resistance of the MTJ. These findings contrast previous studies on AlO based MTJ systems, revealing tunneling magneto thermo power but no tunneling magneto thermocurrent.

cond-mat.mes-hall↗

arXiv2013

Parameter space for thermal spin-transfer torque

Thermal spin-transfer torque describes the manipulation of the magnetization by the application of a heat flow. The effect has been calculated theoretically by Jia et al. in 2011. It is found to require large temperature gradients in the order of Kelvins across an ultra thin MgO barrier. In this paper, we present results on the fabrication and the characterization of magnetic tunnel junctions with 3 monolayer thin MgO barriers. The quality of the interfaces at different growth conditions is studied quantitatively via high-resolution transmission electron microscopy imaging. We demonstrate tunneling magneto resistance ratios of up to 55% to 64% for 3 to 4 monolayer barrier thickness. Magnetic tunnel junctions with perpendicular magnetization anisotropy show spin-transfer torque switching with a critical current of 0.2 MA/cm$^2$. The thermally generated torque is calculated ab initio using the Korringa-Kohn-Rostoker and non-equilibrium Green's function method. Temperature gradients generated from femtosecond laser pulses were simulated using COMSOL, revealing gradients of 20 K enabling thermal spin-transfer-torque switching.

cond-mat.mes-hall↗

arXiv2013

Thermally driven spin and charge currents in thin NiFe2O4/Pt films

We present results on the longitudinal spin Seebeck effect (LSSE) shown by semiconducting ferrimagnetic NiFe2O4/Pt films from room temperature down to 50K base temperature. To the best of our knowledge, this is the first observation of spin caloric effect in NiFe2O4 thin films. The temperature dependence of the conductivity has been studied in parallel to obtain information about the origin of the electric potentials detected at the Pt coverage of the ferrimagnet in order to distinguish the LSSE from the anomalous Nernst effect. Furthermore, the dependence of the LSSE on temperature gradients as well as the influence of an external magnetic field direction is investigated.

cond-mat.mtrl-sci↗

arXiv2013

Influence of MgO tunnel barrier thickness on spin-transfer ferromagnetic resonance and torque in magnetic tunnel junctions

Spin-transfer ferromagnetic resonance (ST-FMR) in symmetric magnetic tunnel junctions (MTJs) with a varied thickness of the MgO tunnel barrier (0.75 nm < $t_{MgO}$ < 1.05 nm) is studied using the spin-torque diode effect. The application of an RF current into nanosized MTJs generates a DC mixing voltage across the device when the frequency is in resonance with the resistance oscillations arising from the spin transfer torque. Magnetization precession in the free and reference layers of the MTJs is analyzed by comparing ST-FMR signals with macrospin and micromagnetic simulations. From ST-FMR spectra at different DC bias voltage, the in-plane and perpendicular torkances are derived. The experiments and free-electron model calculations show that the absolute torque values are independent of tunnel barrier thickness. The influence of coupling between the free and reference layer of the MTJs on the ST-FMR signals and the derived torkances are discussed.

cond-mat.mes-hall↗