Searcharxiv⌕ Search

arXiv subjects

G. Ciovati

Publications and source records attributed to G. Ciovati.

At least 19 recordsLinked to original sources
arXiv2025

Simulation of the thermoelectric effect in a multi-metallic superconducting cavity

Superconducting radio frequency accelerating cavities made with different material layers, such as copper, Nb or Nb3Sn, are susceptible to thermoelectric effects due to differences in Seebeck coefficients between the metals. A temperature gradient across the surfaces can drive thermoelectric currents, which may impact the cavity performance. A layered Cu/Nb/Nb3Sn single cell cavity was tested with cryocoolers in 2022. Three heaters were mounted on the cavity surface at different locations and three single axis cryogenic fluxgate magnetometers were attached close to the cavity equator. A linear increase in the magnetic field was measured while increasing the heaters power. The cavity setup was analysed with COMSOL and the results showed a trend similar to that observed in the experiment. This contribution details the approach chosen for the simulation and some of the challenges encountered.

physics.acc-ph↗
arXiv2024

Role of microstructure on flux expulsion of superconducting radio frequency cavities

The trapped residual magnetic flux during the cool-down due to the incomplete Meissner state is a significant source of radio frequency losses in superconducting radio frequency (SRF) cavities. Here, we show a clear correlation between the niobium microstructure in elliptical cavity geometry and flux expulsion behavior. In particular, a traditionally fabricated Nb cavity half cell from an annealed poly-crystalline Nb sheet after an 800 $^\circ$C heat treatment leads to a bi-modal microstructure that ties in with flux trapping and inefficient flux expulsion. This non-uniform microstructure is related to varying strain profiles along the cavity shape. A novel approach to prevent this non uniform microstructure is presented by fabricating a 1.3 GHz single cell Nb cavity with a cold-worked sheet and subsequent heat treatment leading to better flux expulsion after 800 $^\circ$C/3 h. Microstructural evolution by electron backscattered diffraction-orientation imaging microscopy on cavity cutouts, and flux pinning behavior by dc-magnetization on coupon samples confirms a reduction in flux pinning centers with increased heat treatment temperature. The heat treatment temperature dependent mechanical properties and thermal conductivity are reported. The significant impact of cold-work in this study demonstrates clear evidence for the importance of microstructure required for high-performance superconducting cavities with reduced losses caused by magnetic flux trapping.

physics.acc-ph↗
arXiv2024

The Continuous Electron Beam Accelerator Facility at 12 GeV

This review paper describes the energy-upgraded CEBAF accelerator. This superconducting linac has achieved 12 GeV beam energy by adding 11 new high-performance cryomodules containing eighty-eight superconducting cavities that have operated CW at an average accelerating gradient of 20 MV/m. After reviewing the attributes and performance of the previous 6 GeV CEBAF accelerator, we discuss the upgraded CEBAF accelerator system in detail with particular attention paid to the new beam acceleration systems. In addition to doubling the acceleration in each linac, the upgrade included improving the beam recirculation magnets, adding more helium cooling capacity to allow the newly installed modules to run cold, adding a new experimental hall, and improving numerous other accelerator components. We review several of the techniques deployed to operate and analyze the accelerator performance, and document system operating experience and performance. In the final portion of the document, we present much of the current planning regarding projects to improve accelerator performance and enhance operating margins, and our plans for ensuring CEBAF operates reliably into the future. For the benefit of potential users of CEBAF, the performance and quality measures for beam delivered to each of the experimental halls is summarized in the appendix.

physics.acc-ph↗
arXiv2024

Field, frequency and temperature dependence of the surface resistance of nitrogen diffused niobium superconducting radio frequency cavities

We report the RF performance of several single-cell superconducting radio-frequency cavities subjected to low temperature heat treatment in nitrogen environment. The cavities were treated at temperature 120 - 165 $^{\circ}$C for an extended period of time (24 - 48 hours) either in high vacuum or in a low partial pressure of ultra-pure nitrogen. The improvement in $Q_0$ with a Q-rise was observed when nitrogen gas was injected at $\sim$300 $^{\circ} $C during the cavity cooldown from 800 $^{\circ}$C and held at 165 $^{\circ}$C, without any degradation in accelerating gradient over the baseline performance. The treatment was applied to several elliptical cavities with frequency ranging from 0.75 GHz to 3.0 GHz, showing an improved quality factor as a result of low temperature nitrogen treatments. The Q-rise feature is similar to that achieved by nitrogen alloying Nb cavities at higher temperature, followed by material removal by electropolishing. The surface modification was confirmed by the change in electronic mean free path and tuned with the temperature and duration of heat treatment. The decrease of the temperature-dependent surface resistance with increasing RF field, resulting in a Q-rise, becomes stronger with increasing frequency and decreasing temperature. The data suggest a crossover frequency of $\sim 0.95$~GHz above which the Q-rise phenomenon occurs at 2~K. Some of these results can be explained qualitatively with an existing model of intrinsic field-dependence of the surface resistance with both equilibrium and nonequilibrium quasiparticle distribution functions. The change in the Q-slope below 0.95 GHz may result from masking contribution of trapped magnetic flux to the residual surface resistance.

cond-mat.supr-con↗
arXiv2023

Quench Detection in a Superconducting Radio Frequency Cavity with Combine Temperature and Magnetic Field Mapping

Local dissipation of RF power in superconducting radio frequency cavities create so called hot spots, primary precursors of cavity quench driven by either thermal or magnetic instability. These hot spots are detected by a temperature mapping system, and a large increase in temperature on the outer surface is detected during cavity quench events. Here, we have used combined magnetic and temperature mapping systems using anisotropic magnetoresistance (AMR) sensors and carbon resisters to locate the hot spots and areas with high trapped flux on a 3.0 GHz single-cell Nb cavity during the RF tests at 2.0 K. The quench location and hot spots were detected near the equator when the residual magnetic field in the Dewar is kept < 1 mG. The hot spots and quench locations moved when the magnetic field is trapped locally, as detected by T-mapping system. No significant dynamics of trapped flux is detected by AMR sensors, however, change in magnetic flux during cavity quench is detected by a flux gate magnetometer, close to the quench location. The result provides the direct evidence of hot spots and quench events due to localized trapped vortices.

cond-mat.supr-con↗
arXiv2023

Development of a prototype superconducting radio-frequency cavity for conduction-cooled accelerators

The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normal-conducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent progress in the development of high-quality Nb$_3$Sn film coatings along with the availability of cryocoolers with high cooling capacity at 4 K makes it feasible to operate SRF cavities cooled by thermal conduction at relevant accelerating gradients for use in accelerators. A possible use of conduction-cooled SRF linacs is for environmental applications, requiring electron beams with energy of $1 - 10$ MeV and 1 MW of power. We have designed a 915 MHz SRF linac for such an application and developed a prototype single-cell cavity to prove the proposed design by operating it with cryocoolers at the accelerating gradient required for 1 MeV energy gain. The cavity has a $\sim 3$ $μ$m thick Nb$_3$Sn film on the inner surface, deposited on a $\sim4$ mm thick bulk Nb substrate and a bulk $\sim7$ mm thick Cu outer shell with three Cu attachment tabs. The cavity was tested up to a peak surface magnetic field of 53 mT in liquid He at 4.3 K. A horizontal test cryostat was designed and built to test the cavity cooled with three Gifford-McMahon cryocoolers. The rf tests of the conduction-cooled cavity, performed at General Atomics, achieved a peak surface magnetic field of 50 mT and stable operation was possible with up to 18.5 W of rf heat load. The peak frequency shift due to microphonics was 23 Hz. These results represent the highest peak surface magnetic field achieved in a conduction-cooled SRF cavity to date and meet the requirements for a 1 MeV energy gain.

physics.acc-ph↗
arXiv2022

Key directions for research and development of superconducting radio frequency cavities

Radio frequency superconductivity is a cornerstone technology for many future HEP particle accelerators and experiments from colliders to proton drivers for neutrino facilities to searches for dark matter. While the performance of superconducting RF (SRF) cavities has improved significantly over the last decades, and the SRF technology has enabled new applications, the proposed HEP facilities and experiments pose new challenges. To address these challenges, the field continues to generate new ideas and there seems to be a vast room for improvements. In this paper we discuss the key research directions that are aligned with and address the future HEP needs.

physics.acc-ph↗
arXiv2022

Next-Generation Superconducting RF Technology based on Advanced Thin Film Technologies and Innovative Materials for Accelerator Enhanced Performance and Energy Reach

Superconducting RF is a key technology for future particle accelerators, now relying on advanced surfaces beyond bulk Nb for a leap in performance and efficiency. The SRF thin film strategy aims at transforming the current SRF technology by using highly functional materials, addressing all the necessary functions. The community is deploying efforts in three research thrusts to develop next-generation thin-film based cavities. Nb on Cu cavities are developed to perform as good as or better than bulk Nb at reduced cost and with better thermal stability. Recent results showing improved accelerating field and dramatically reduced Q slope show their potential for many applications. The second research thrust is to develop cavities coated with materials that can operate at higher temperatures or sustain higher fields. Proof of principle has been established for the merit of Nb3Sn for SRF application. Research is now needed to further exploit the material and reach its full potential with novel deposition techniques. The third line of research is to push SRF performance beyond the capabilities of the superconductors alone with multilayered coatings. In parallel, developments are needed to provide quality substrates, cooling schemes and cryomodule design tailored to thin film cavities. Recent results in these three research thrusts suggest that SRF thin film technologies are at the eve of a technological revolution. For them to mature, active community support and sustained funding are needed to address fundamental developments supporting material deposition techniques, surface and RF research, technical challenges associated with scaling and industrialization. With dedicated and sustained investment, next-generation thin-film based cavities will become a reality with high performance and efficiency, facilitating energy sustainable science while enabling higher luminosity, and higher energy.

physics.acc-ph↗
arXiv2022

Medium-Grain Niobium SRF Cavity Production Technology for Science Frontiers and Accelerator Applications

We propose cost-effective production of medium grain (MG) niobium (Nb) discs directly sliced from forged and annealed billet. This production method provides clean surface conditions and reliable mechanical characteristics with sub-millimeter average grain size resulting in stable SRF cavity production. We propose to apply this material to particle accelerator applications in the science and industrial frontiers. The science applications require high field gradients (>~40 MV/m) particularly in pulse mode. The industrial applications require high Q0 values with moderate gradients (~30 MV/m) in CW mode operation. This report describes the MG Nb disc production recently demonstrated and discusses future prospects for application in advanced particle accelerators in the science and industrial frontiers.

physics.acc-ph↗
arXiv2022

Nonlinear Meissner effect in Nb3Sn coplanar resonators

We investigated the nonlinear Meissner effect (NLME) in Nb$_3$Sn thin film coplanar resonators by measuring the resonance frequency as a function of a parallel magnetic field at different temperatures. We used low rf power probing in films thinner than the London penetration depth $λ(B)$ to significantly increase the field onset of vortex penetration and measure the NLME under equilibrium conditions. Contrary to the conventional quadratic increase of $λ(B)$ with $B$ expected in s-wave superconductors, we observed a nearly linear increase of the penetration depth with $B$. We concluded that this behavior of $λ(B)$ is due to weak linked grain boundaries in our polycrystalline Nb$_3$Sn films, which can mimic the NLME expected in a clean d-wave superconductor.

cond-mat.supr-con↗
arXiv2020

Multi-metallic conduction cooled superconducting radio-frequency cavity with high thermal stability

Superconducting radio-frequency cavities are commonly used in modern particle accelerators for applied and fundamental research. Such cavities are typically made of high-purity, bulk Nb and are cooled by a liquid helium bath at a temperature of ~2 K. The size, cost and complexity of operating a particle accelerator with a liquid helium refrigerator makes the current cavity technology not favorable for use in industrial-type accelerators. We developed a multi-metallic 1.495~GHz elliptical cavity conductively cooled by a cryocooler. The cavity has a ~2 $μ$m thick layer of Nb$_3$Sn on the inner surface, exposed to the rf field, deposited on a ~3 mm thick bulk Nb shell and a bulk Cu shell, of thickness $\geqslant 5$ mm deposited on the outer surface by electroplating. A bolt-on Cu plate 1.27 cm thick was used to thermally connect the cavity equator to the second stage of a Gifford-McMahon cryocooler with a nominal capacity of 2 W at 4.2 K. The cavity was tested initially in liquid helium at 4.3 K and reached a peak surface magnetic field of ~36 mT with a quality factor of $2\times 10^9$. The cavity cooled by the crycooler achieved a peak surface magnetic field of ~29 mT, equivalent to an accelerating gradient of 6.5 MV/m, and it was able to operate in continuous-wave with as high as 5 W dissipation in the cavity for 1 h without any thermal breakdown. This result represents a paradigm shift in the technology of superconducting accelerator cavities.

physics.ins-det↗
arXiv2018

Design of a cw, low energy, high power superconducting linac for environmental applications

The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The beam energy requirement is rather modest, on the order of a few MeV, however the adoption of the technology at an industrial scale requires the availability of high beam power, of the order of 1 MW, in a cost effective way. In this article we present the design of a compact superconducting accelerator capable of delivering a cw electron beam with a current of 1 A and an energy of 1 MeV. The main components are an rf-gridded thermionic gun and a conduction cooled beta= 0.5 elliptical Nb3Sn cavity with dual coaxial power couplers. An engineering and cost analysis shows that the proposed design would result in a processing cost competitive with alternative treatment methods.

physics.acc-ph↗
arXiv2018

Insight into bulk niobium superconducting RF cavities performances by tunneling spectroscopy

Point contact tunneling (PCT) spectroscopy measurements are reported over wide areas of cm-sized cut outs from niobium superconducting RF cavities. A comparison is made between a high-quality, conventionally processed (CP) cavity with a high field Q drop for acceleration field E $>$ 20 MV/m and a nitrogen doped (N-doped) cavity that exhibits an increasing Q up to fields approaching 15 MV/m. The CP cavity displays hot spot regions at high RF fields where Q-drop occurs as well as unaffected regions (cold spots). PCT data on cold spots reveals a near ideal BCS density of states (DOS) with gap parameters, $Δ$ as high as 1.62 meV, that are among the highest values ever reported for Nb. Hot spot regions exhibit a wide distribution of gap values down to $Δ\sim$ 1.0 meV and DOS broadening characterized by a relatively large value of pair-breaking rate, $Γ$, indicating surface regions of significantly reduced superconductivity. In addition, hot spots commonly exhibit Kondo tunneling peaks indicative of surface magnetic moments attributed to a defective oxide. N-doped cavities reveal a more homoegeneous gap distribution centered at $Δ\sim$ 1.5 meV and relatively small values of $Γ/Δ$. The absence of regions of significantly reduced superconductivity indicates that the N interstitials are playing an important role in preventing the formation of hydride phases and other macroscopic defects which might otherwise severely affect the local, surface superconductivity that lead to hot spot formation. The N-doped cavities also display a significantly improved surface oxide, i.e., increased thickness and tunnel barrier height, compared to CP cavities. These results help explain the improved performance of N-doped cavities and give insights into the origin of the initial increasing Q with RF amplitude.

cond-mat.supr-con↗
arXiv2015

AC/RF Superconductivity

This contribution provides a brief introduction to AC/RF superconductivity, with an emphasis on application to accelerators. The topics covered include the surface impedance of normal conductors and superconductors, the residual resistance, the field dependence of the surface resistance, and the superheating field.

physics.acc-ph↗
arXiv2014

Reply to "Comment on the 'Decrease of the surface resistance in superconducting niobium resonator cavities by the microwave field'"

In a recent comment [arXiv:1405.2978v1 (2014)] Romanenko and Grassellino made unsubstantiated statements about our work [Appl. Phys. Lett. 104, 092601 (2014)] and ascribed to us wrong points which we had not made. Here we show that the claims of Romanenko and Grassellino are based on misinterpretation of our Letter and inadequate data analysis in their earlier work [*]. [*] A. Romanenko and A. Grassellino, Appl. Phys. Lett. 102, 252603 (2013)

physics.acc-ph↗
arXiv2013

The Rise of Ingot Niobium as a Material for Superconducting Radiofrequency Accelerating Cavities

As a result of a collaboration between Jefferson Lab and niobium manufacturer CBMM, ingot niobium was explored as a possible material for superconducting radiofrequency (SRF) cavity fabrication. The first single cell cavity from large grain high purity niobium was fabricated and successfully tested at Jefferson Lab in 2004. This pioneering work triggered research activities in other SRF laboratories around the world. Large grain niobium became not only an interesting alternative material for cavity builders, but also material scientists and surface scientists were eager to participate in the development of this material. Most of the original expectations for this material of being less costly and allowing less expensive fabrication and treatment procedures at the same performance levels in cavities have been met. Many single cell cavities made from material of different suppliers have been tested successfully and several multi-cell cavities have shown the performances comparable to the best cavities made from standard poly-crystalline niobium. Several 9-cell cavities fabricated by Research Instruments and tested at DESY exceeded the best performing fine grain cavities with a record accelerating gradient of Eacc = 45.6 MV/m. Recently- at JLab- by using a new furnace treatment procedure a single cell cavity made of ingot niobium performed at a remarkably high Q0-value (~5x10^10) at an accelerating gradient of ~20 MV/m, at 2K. Such performance levels push the state-of-the art of SRF technology to new limits and are of great interest for future accelerators. This contribution reviews the development of ingot niobium technology and attempts to make a case for this material being the choice for future accelerators.

physics.acc-ph↗