arXiv subjects

G. Ciovati

Publications and source records attributed to G. Ciovati.

23 records · Page 2Linked to original sources

arXiv2013

Effect of high temperature heat treatments on the quality factor of a large-grain superconducting radio-frequency niobium cavity

Large-grain Nb has become a viable alternative to fine-grain Nb for the fabrication of superconducting radio-frequency cavities. In this contribution we report the results from a heat treatment study of a large-grain 1.5 GHz single-cell cavity made of "medium purity" Nb. The baseline surface preparation prior to heat treatment consisted of standard buffered chemical polishing. The heat treatment in the range 800 - 1400 C was done in a newly designed vacuum induction furnace. Q0 values of the order of 2x1010 at 2.0 K and peak surface magnetic field (Bp) of 90 mT were achieved reproducibly. A Q0-value of (5+-1)1010 at 2.0 K and Bp = 90 mT was obtained after heat treatment at 1400 C. This is the highest value ever reported at this temperature, frequency and field. Samples heat treated with the cavity at 1400 C were analyzed by secondary ion mass spectrometry, secondary electron microscopy, energy dispersive X-ray, point contact tunneling and X-ray diffraction and revealed a complex surface composition which includes titanium oxide, increased carbon and nitrogen content but reduced hydrogen concentration compared to a non heat-treated sample.

cond-mat.supr-con↗

arXiv2012

Low temperature laser scanning microscopy of a superconducting radio-frequency cavity

An apparatus was developed to obtain, for the first time, 2D maps of the surface resistance of the inner surface of an operating superconducting radio-frequency niobium cavity by a low-temperature laser scanning microscopy technique. This allows identifying non-uniformities of the surface resistance with a spatial resolution of about one order of magnitude better than with earlier methods and surface resistance resolution of ~ 1 micro-Ohm at 3.3 GHz. A signal-to-noise ratio of about 10 dB was obtained with 240 mW laser power and 1 Hz modulation frequency. The various components of the apparatus, the experimental procedure and results are discussed in detail in this contribution.

cond-mat.supr-con↗

arXiv2009

Buffered Electropolishing -- a New Way for Achieving Extremely Smooth Surface Finish on Nb SRF Cavities To be Used in Particle Accelerators

A new surface treatment technique for niobium (Nb) Superconducting Radio Frequency (SRF) cavities called Buffered Electropolishing (BEP) has been developed at JLab. It was found that BEP could produce the smoothest surface finish on Nb samples ever reported in the literature. Experimental results revealed that the Nb removal rate of BEP could reach as high as 4.09 um/min. This is significantly faster1 than that of the conventional electropolishing technique employing an acid mixture of HF and H2SO4. An investigation is underway to determine the optimum values for all relevant BEP parameters so that the high quality of surface finish achieved on samples can be realized within the geometry of an elliptical RF cavity. Toward this end, single cell Nb cavities are being electropolished with BEP electrolyte at both CEA-Saclay and JLAB. These cavities will be RF tested and the results will be reported through this presentation.

physics.acc-ph↗

arXiv2007

Dynamics of vortex penetration, jumpwise instabilities and nonlinear surface resistance of type-II superconductors in strong rf fields

We consider nonlinear dynamics of a single vortex in a superconductor in a strong rf magnetic field $B_0\sinωt$. Using the London theory, we calculate the dissipated power $Q(B_0,ω)$, and the transient time scales of vortex motion for the linear Bardeen-Stephen viscous drag force, which results in unphysically high vortex velocities during vortex penetration through the oscillating surface barrier. It is shown that penetration of a single vortex through the ac surface barrier always involves penetration of an antivortex and the subsequent annihilation of the vortex antivortex pairs. Using the nonlinear Larkin-Ovchinnikov (LO) viscous drag force at higher vortex velocities $v(t)$ results in a jump-wise vortex penetration through the surface barrier and a significant increase of the dissipated power. We calculate the effect of dissipation on nonlinear vortex viscosity $η(v)$ and the rf vortex dynamics and show that it can also result in the LO-type behavior, instabilities, and thermal localization of penetrating vortex channels. We propose a thermal feedback model of $η(v)$, which not only results in the LO dependence of $η(v)$ for a steady-state motion, but also takes into account retardation of temperature field around rapidly accelerating vortex, and a long-range interaction with the surface. We also address the effect of pinning on the nonlinear rf vortex dynamics and the effect of trapped magnetic flux on the surface resistance $R_s$ calculated as a function or rf frequency and field. It is shown that trapped flux can result in a temperature-independent residual resistance $R_i$ at low $T$, and a hysteretic low-field dependence of $R_i(B_0)$, which can {\it decrease} as $B_0$ is increased, reaching a minimum at $B_0$ much smaller than the thermodynamic critical field $B_c$.

cond-mat.supr-con↗

arXiv2003

Status Report on Multi-Cell Superconducting Cavity Development for Medium-Velocity Beams

Three prototype 6-cell superconducting cavities for acceleration in the velocity range of 0.40 to 0.53 times the speed of light have been fabricated. The quality factor (Q) of the first prototype cavity was above 1E10 for accelerating gradients up to 11 MV/m. The highest gradient reached was about 16 MV/m; the Q was about 3E9 at the maximum gradient.

physics.acc-ph↗