arXiv subjects

Gabriele Minervini

Publications and source records attributed to Gabriele Minervini.

At least 19 recordsLinked to original sources

arXiv2026

In orbit background for hard X-ray CubeSat polarimeters: case study of the CUSP mission in low-earth orbit

The CUbesat Solar Polarimeter (CUSP) project aims to measure the linear polarization of solar flares in the 25 - 100 keV hard X-ray band using a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, initiated in December 2024 and closed on July 2nd, 2026, estimating the in orbit background to optimize the signal-to-background ratio was one of the key objectives. In low-Earth orbit, the instrument is exposed to cosmic and albedo X-ray backgrounds, charged particles, and secondary radiation from the spacecraft and atmosphere. Simulating these contributions enables optimization of detector geometry and shielding to maximize signal-to-noise performance. We present initial in orbit background estimates for CUSP using a Geant4-based simulator. A detailed mass model of the CUSP has been implemented to simulate background components and estimate the background count rate in the CUSP orbit.

astro-ph.IM↗

arXiv2026

The CUSP CubeSat mission for space weather multi-physics analysis, design, and testing

The CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. We present the outcomes of the CUSP's Phase B study, which is ended on 2 July 2026. The design solutions adopted for the mission's most critical multi-physics design drivers will be discussed, these solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. Moreover, we will discuss the validation of the Payload model based on the environmental testing campaign (e.g., vibration) carried out on a demonstrator.

astro-ph.IM↗

arXiv2026

Compton Polarimeter Prototype for the CUbesat Solar Polarimeter (CUSP) mission

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band (25-100 keV) by means of a dual-phase Compton polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project under development as part of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. In the frame of CUSP's Phase B, which started in December 2024, a flight-representative prototype of the Compton polarimeter has been developed and characterized with hard X-ray sources in the laboratory. This prototype consists of a 4$\times$4 central matrix of plastic scintillator bars surrounded by 4 strips of 8 elongated GAGG scintillators, respectively coupled to a multi-anode photomultiplier tube and arrays of avalanche photodiodes. These sensors are read out by custom front-end electronics based on MAROC-3A and SKIROC-2A ASICs with a Xilinx Artix 7 FPGA. The plastic scintillators act as scatterers, while the GAGG bars fully absorb the scattered photons. Coincident plastic-GAGG events allow for reconstructing the Compton scattering direction, whose distribution allows for inferring the polarization parameters of the source. We report here the measured performance of the polarimeter prototype using well-known radioactive isotopes and X-ray tubes, allowing us to assess the performance of our polarimeter prototype over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2026

Spectral performance of single-channel plastic and GAGG scintillator bars of the CUbesat Solar Polarimeter (CUSP)

Our Sun is the closest X-ray astrophysical source to Earth. As such, it makes a formidable case study to better understand astrophysical processes. Solar flares are in particular very interesting as they are linked to coronal mass ejections as well as magnetic field reconnection sites in the solar atmosphere. Flares can therefore provide insightful information on the physical processes at play on their production sites, but also on the emission and acceleration of energetic charged particles towards our planet, making it a formidable forecasting tool for space weather. While solar flares are critical to understanding magnetic reconnection and particle acceleration, their hard X-ray polarization -- key to distinguishing between competing theoretical models -- remains poorly constrained by existing observations. To address this, we present the CUbesat Solar Polarimeter (CUSP), a mission under development to perform solar flare polarimetry in the 25-100 keV energy range. CUSP consists of a 6U-XL platform hosting a dual-phase Compton polarimeter. The polarimeter is made of a central assembly of four 4x4 arrays of plastic scintillators, each coupled to multi-anode photomultiplier tubes, surrounded by four strips of eight elongated GAGG scintillator bars coupled to avalanche photodiodes. Both types of sensors from Hamamatsu are respectively read out by the MAROC-3A and SKIROC-2A ASICs from Weeroc. In this manuscript, we present the preliminary spectral performances of single plastic and GAGG channels measured in the laboratory using development boards of the ASICs foreseen for the flight model.

astro-ph.IM↗

arXiv2025

Solar Flare Hard X-ray Polarimetry with the CUbesat Solar Polarimeter (CUSP) mission

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission planned for a launch in low-Earth orbit and aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. It is undergoing a 12-month Phase B that started in December 2024. The Compton polarimeter on board CUSP is composed of two acquisition chains based on plastic scintillators read out by Multi-Anode PhotoMultiplier Tubes for the scatterer part and GAGG crystals coupled to Avalanche PhotoDiodes for the absorbers. An event coincident between the two readout schemes will lead to a measurement of the incoming X-ray's azimuthal scattering angle, linked to the polarization of the solar flare in a statistical manner. The current status of the CUSP mission design, mission analysis, and payload scientific performance will be reported. The latter will be discussed based on preliminary laboratory results obtained in parallel with Geant4 simulations.

astro-ph.SR↗

arXiv2025

The multi-physics analysis, design and testing of CUSP, a CubeSat mission for space weather and solar flares x-ray polarimetry

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. As part of CUSP's Phase B study, which began in December 2024 and will last one year, we present the current development status of the design solutions adopted for the mission's most critical multi-physics design drivers. These solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. In particular, we describe the mechanical design of each structural component, the results of static, dynamic finite element analyses, and a proposal for topological optimization of the interface between the platform and payload and some fixture for test, and the preliminary environmental testing campaign (e.g., vibration, shock) that will be carried out on a mechanical demonstrator.

astro-ph.IM↗

arXiv2025

The CUbesat Solar Polarimeter (CUSP): mission overview II

The CUbesat Solar Polarimeter (CUSP) project is an Earth-orbiting CubeSat mission designed to measure the linear polarization of solar flares in the hard X-ray band using a Compton scattering polarimeter. CUSP will enable the study of magnetic reconnection and particle acceleration within the Sun's flaring magnetic structures. This project is being developed within the framework of the Italian Space Agency's Alcor Program, which aims to foster new CubeSat missions. CUSP entered its Phase B in December 2024, a phase scheduled to last 12 months. This paper reports on the current status of the CUSP mission design, mission analysis, and payload scientific performance.

astro-ph.SR↗

arXiv2025

CUbesat Solar Polarimeter (CUSP) Sensitivity Estimation and Performance Optimization using Geant4

The CUbesat Solar Polarimeter (CUSP) aims to measure the linear polarization of solar flares in the 25-100 keV X-ray band using a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star by providing high-sensitivity polarization measurements. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, which began in December 2024 and will continue for one year, we present the development status of the Geant4 based simulator to accurately simulate the detectors response and initial results on the sensitivity of the instrument. Geant4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. We implemented a detailed CUSP Mass Model within Geant4 to simulate and estimate the instruments sensitivity, correcting the geometric effects of the instrument. We also evaluated the effect of backscattering shielding on the sensitivity to optimize the mass model of the instrument.

astro-ph.SR↗

arXiv2025

Prototype Development and Calibration of the CUbesat Solar Polarimeter (CUSP)

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It has been proposed as a constellation of a two Cubesat mission to monitor the Sun for Space Weather, and will proceed with a single-satellite asset in its baseline implementation. In the frame of CUSP's Phase B study, that started in December 2024 for a 1-year period, we present the development status of this dual-phase polarimeter. Preliminary laboratory results using two chains of acquisition will be discussed. The first chain of acquisition, based on the Hamamatsu R7600 multi-anode photomultiplier tubes coupled to plastic scintillator bars and read out by the MAROC-3A ASIC, is used to detect the Compton scattering of incoming photons. On the other hand, GAGG crystals coupled to avalanche photo-diodes with a readout based on the SKIROC-2A ASIC are used to absorb the scattered photons. By reconstructing the azimuthal scattering direction for many incoming photons, one can infer the linear polarization degree and angle of the source. We will discuss the calibration results obtained with our prototype detector by using well-known radioactive isotopes, allowing us to assess the performances of our detector over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2025

Study of the HV power supply modules for the CUbesat Solar Polarimeter (CUSP)

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. CUSP undergoing the Phase B started in December 2024 that will last for 12 month. The Compton polarimeter of the CUSP payload performs coincidence measurements between plastic scintilaltors and GaGG(Ce) crystals to derive the polarization of X-rays. These sensors are readout by Multi Anode Photomultiplier Tubes (MAPMTs) and Avalanche Photodiodes (APDs) respectively. Both sensors need an HV power supply up to -1~kV (for the MAPMT) and +500~V (for the APD). We tested precision regulated High Voltage DC/DC Converters by HVM Technology Inc. with Sub-Miniature Case Size ($0.85''\times0.85''\times0.60''$) of the SMHV series. These modules are compact and suited for CubeSat missions.

astro-ph.IM↗

arXiv2025

The X-ray Integral Field Unit at the end of the Athena reformulation phase

The Athena mission entered a redefinition phase in July 2022, driven by the imperative to reduce the mission cost at completion for the European Space Agency below an acceptable target, while maintaining the flagship nature of its science return. This notably called for a complete redesign of the X-ray Integral Field Unit (X-IFU) cryogenic architecture towards a simpler active cooling chain. Passive cooling via successive radiative panels at spacecraft level is now used to provide a 50 K thermal environment to an X-IFU owned cryostat. 4.5 K cooling is achieved via a single remote active cryocooler unit, while a multi-stage Adiabatic Demagnetization Refrigerator ensures heat lift down to the 50 mK required by the detectors. Amidst these changes, the core concept of the readout chain remains robust, employing Transition Edge Sensor microcalorimeters and a SQUID-based Time-Division Multiplexing scheme. Noteworthy is the introduction of a slower pixel. This enables an increase in the multiplexing factor (from 34 to 48) without compromising the instrument energy resolution, hence keeping significant system margins to the new 4 eV resolution requirement. This allows reducing the number of channels by more than a factor two, and thus the resource demands on the system, while keeping a 4' field of view (compared to 5' before). In this article, we will give an overview of this new architecture, before detailing its anticipated performances. Finally, we will present the new X-IFU schedule, with its short term focus on demonstration activities towards a mission adoption in early 2027.

astro-ph.IM↗

arXiv2025

The TES-based Cryogenic AntiCoincidence Detector of ATHENA X-IFU: Validation of the thermal end-to-end simulator towards the updated Demonstration Model (DM 1.1)

The Cryogenic AntiCoincidence Detector (CryoAC) is a key element of the X-ray Integral Field Unit (X-IFU) on board the future ATHENA X-ray observatory. It is a TES-based detector designed to reduce the particle background of the instrument, thereby increasing its sensitivity. The detector design is driven by an end-to-end simulator which includes the electro-thermal modelling of the detector and the dynamics of its readout chain. Here, we present the measurements carried out on the last CryoAC single pixel prototype, namely DM127, in order to evaluate the critical thermal parameters of the detector and consequently to tune and validate the CryoAC end-to-end simulator.

astro-ph.IM↗

arXiv2024

The Wide Field Monitor (WFM) of the China-Europe eXTP (enhanced X-ray Timing and Polarimetry) mission

The eXTP mission is a major project of the Chinese Academy of Sciences (CAS), with a large involvement of Europe. Its scientific payload includes four instruments: SFA, PFA, LAD and WFM. They offer an unprecedented simultaneous wide-band Xray timing and polarimetry sensitivity. A large European consortium is contributing to the eXTP study, both for the science and the instrumentation. Europe is expected to provide two of the four instruments: LAD and WFM; the LAD is led by Italy and the WFM by Spain. The WFM for eXTP is based on the design originally proposed for the LOFT ESA M3 mission, that underwent a Phase A feasibility study. It will be a wide field of view X-ray monitor instrument working in the 2-50 keV energy range, achieved with large-area Silicon Drift Detectors (SDDs), similar to the ones used for the LAD but with better spatial resolution. The WFM will consist of 3 pairs of coded mask cameras with a total combined field of view (FoV) of 90x180 degrees at zero response and a source localisation accuracy of ~1 arc min. The main goal of the WFM is to provide triggers for the target of opportunity observations of the SFA, PFA and LAD, in order to perform the core science programme, dedicated to the study of matter under extreme conditions of density, gravity and magnetism. In addition, the unprecedented combination of large field of view and imaging capability, down to 2 keV, of the WFM will allow eXTP to make important discoveries of the variable and transient X-ray sky, and provide X-ray coverage of a broad range of astrophysical objects covered under 'observatory science', such as gamma-ray bursts, fast radio bursts, gravitational wave electromagnetic counterparts. In this paper we provide an overview of the WFM instrument, explaining its design, configuration, and anticipated performance.

astro-ph.IM↗

arXiv2024

STROBE-X High Energy Modular Array (HEMA)

The High Energy Modular Array (HEMA) is one of three instruments that compose the STROBE-X mission concept. The HEMA is a large-area, high-throughput non-imaging pointed instrument based on the Large Area Detector developed as part of the LOFT mission concept. It is designed for spectral timing measurements of a broad range of sources and provides a transformative increase in sensitivity to X-rays in the energy range of 2--30 keV compared to previous instruments, with an effective area of 3.4 m$^{2}$ at 8.5 keV and an energy resolution of better than 300 eV at 6 keV in its nominal field of regard.

astro-ph.IM↗

arXiv2024

The end-to-end simulator of the ATHENA X-IFU Cryogenic AntiCoincidence detector (CryoAC)

The X-IFU is one of the two instruments of ATHENA, the next ESA large X-ray observatory. It is a cryogenic spectrometer based on an array of TES microcalorimeters. To reduce the particle background, the TES array works in combination with a Cryogenic AntiCoincidence detector (CryoAC). The CryoAC is a 4-pixel detector, based on ~1 cm2 silicon absorbers sensed by Ir/Au TES. It is required to have a wide energy bandwidth (from 20 keV to ~1 MeV), high efficiency (< 0.014% missed particles), low dead-time (< 1%) and good time-tagging accuracy (10 us at 1 sigma). An end-to-end simulator of the CryoAC detector has been developed both for design and performance assessment, consisting of several modules. First, the in-flight flux of background particles is evaluated by Geant4 simulations. Then, the current flow in the TES is evaluated by solving the electro-thermal equations of microcalorimeters, and the detector output signal is generated by simulating the SQUID FLL dynamics. Finally, the output is analyzed by a high-efficiency trigger algorithm, producing the simulated CryoAC telemetry. Here, we present in detail this end-to-end simulator, and how we are using it to define the new CryoAC baseline configuration in the new Athena context.

astro-ph.IM↗

arXiv2024

The evaluation of the CUSP scientific performance by a GEANT4 Monte Carlo simulation

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It is approved for a Phase B study. In this work, we report on the accurate simulation of the detector's response to evaluate the scientific performance. A GEANT4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. Using this approach, we implemented a detailed CUSP Mass Model. In this work, we report on the evaluation of the detector's effective area as a function of the beam energy.

astro-ph.IM↗

arXiv2024

The multi$-$physics analysis and design of CUSP, a two CubeSat constellation for Space Weather and Solar flares X-ray polarimetry

The CUbesat Solar Polarimeter (CUSP) project aims to develop a constellation of two CubeSats orbiting the Earth to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter on board of each satellite. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures. CUSP is a project approved for a Phase B study by the Italian Space Agency in the framework of the Alcor program aimed to develop CubeSat technologies and missions. In this paper we describe the a method for a multi-physical simulation analysis while analyzing some possible design optimization of the payload design solutions adopted. In particular, we report the mechanical design for each structural component, the results of static and dynamic finite element analysis, the preliminary thermo-mechanical analysis for two specific thermal cases (hot and cold orbit) and a topological optimization of the interface between the platform and the payload.

astro-ph.IM↗

arXiv2024

The CUbesat Solar Polarimeter (CUSP) mission overview

The CUbesat Solar Polarimeter (CUSP) project is a future CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band, by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. The project is in the framework of the Italian Space Agency Alcor Program, which aims to develop new CubeSat missions. CUSP is approved for a Phase B study that will last for 12 months, starting in mid-2024. We report on the current status of the CUSP mission project as the outcome of the Phase A.

astro-ph.IM↗