arXiv subjects

Giovanni De Cesare

Publications and source records attributed to Giovanni De Cesare.

At least 19 recordsLinked to original sources

arXiv2026

In orbit background for hard X-ray CubeSat polarimeters: case study of the CUSP mission in low-earth orbit

The CUbesat Solar Polarimeter (CUSP) project aims to measure the linear polarization of solar flares in the 25 - 100 keV hard X-ray band using a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, initiated in December 2024 and closed on July 2nd, 2026, estimating the in orbit background to optimize the signal-to-background ratio was one of the key objectives. In low-Earth orbit, the instrument is exposed to cosmic and albedo X-ray backgrounds, charged particles, and secondary radiation from the spacecraft and atmosphere. Simulating these contributions enables optimization of detector geometry and shielding to maximize signal-to-noise performance. We present initial in orbit background estimates for CUSP using a Geant4-based simulator. A detailed mass model of the CUSP has been implemented to simulate background components and estimate the background count rate in the CUSP orbit.

astro-ph.IM↗

arXiv2026

The CUSP CubeSat mission for space weather multi-physics analysis, design, and testing

The CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. We present the outcomes of the CUSP's Phase B study, which is ended on 2 July 2026. The design solutions adopted for the mission's most critical multi-physics design drivers will be discussed, these solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. Moreover, we will discuss the validation of the Payload model based on the environmental testing campaign (e.g., vibration) carried out on a demonstrator.

astro-ph.IM↗

arXiv2026

Compton Polarimeter Prototype for the CUbesat Solar Polarimeter (CUSP) mission

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band (25-100 keV) by means of a dual-phase Compton polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project under development as part of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. In the frame of CUSP's Phase B, which started in December 2024, a flight-representative prototype of the Compton polarimeter has been developed and characterized with hard X-ray sources in the laboratory. This prototype consists of a 4$\times$4 central matrix of plastic scintillator bars surrounded by 4 strips of 8 elongated GAGG scintillators, respectively coupled to a multi-anode photomultiplier tube and arrays of avalanche photodiodes. These sensors are read out by custom front-end electronics based on MAROC-3A and SKIROC-2A ASICs with a Xilinx Artix 7 FPGA. The plastic scintillators act as scatterers, while the GAGG bars fully absorb the scattered photons. Coincident plastic-GAGG events allow for reconstructing the Compton scattering direction, whose distribution allows for inferring the polarization parameters of the source. We report here the measured performance of the polarimeter prototype using well-known radioactive isotopes and X-ray tubes, allowing us to assess the performance of our polarimeter prototype over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2026

Spectral performance of single-channel plastic and GAGG scintillator bars of the CUbesat Solar Polarimeter (CUSP)

Our Sun is the closest X-ray astrophysical source to Earth. As such, it makes a formidable case study to better understand astrophysical processes. Solar flares are in particular very interesting as they are linked to coronal mass ejections as well as magnetic field reconnection sites in the solar atmosphere. Flares can therefore provide insightful information on the physical processes at play on their production sites, but also on the emission and acceleration of energetic charged particles towards our planet, making it a formidable forecasting tool for space weather. While solar flares are critical to understanding magnetic reconnection and particle acceleration, their hard X-ray polarization -- key to distinguishing between competing theoretical models -- remains poorly constrained by existing observations. To address this, we present the CUbesat Solar Polarimeter (CUSP), a mission under development to perform solar flare polarimetry in the 25-100 keV energy range. CUSP consists of a 6U-XL platform hosting a dual-phase Compton polarimeter. The polarimeter is made of a central assembly of four 4x4 arrays of plastic scintillators, each coupled to multi-anode photomultiplier tubes, surrounded by four strips of eight elongated GAGG scintillator bars coupled to avalanche photodiodes. Both types of sensors from Hamamatsu are respectively read out by the MAROC-3A and SKIROC-2A ASICs from Weeroc. In this manuscript, we present the preliminary spectral performances of single plastic and GAGG channels measured in the laboratory using development boards of the ASICs foreseen for the flight model.

astro-ph.IM↗

arXiv2025

SAG-SCI: the Real-time, High-level Analysis Software for Array Control and Data Acquisition of the Cherenkov Telescope Array Observatory

The Cherenkov Telescope Array Observatory (CTAO) is going to be the leading observatory for very-high-energy gamma-rays over the next decades. Its unique sensitivity, wide field of view, and rapid slewing capability make the CTAO especially suited to study transient astrophysical phenomena. The CTAO will analyse its data in real-time, responding to external science alerts on transient events and issuing its own. The Science Alert Generation (SAG) automated pipeline, a component of the Array Control and Data Acquisition (ACADA) software, is designed to detect and issue candidate science alerts. In this work, we present the current development status of SAG-SCI, the SAG component responsible for the real-time, high-level analysis of CTAO data. The SAG-SCI pipelines receive gamma-ray data from multiple reconstruction lines, merge them, store them in a database, and trigger several parallel scientific analyses on the latest data. These analyses include estimating target significance and flux, producing sky maps and light curves, and conducting blind searches for sources within the field of view. We execute SAG-SCI on a set of simulated gamma-ray data, detecting the simulated sources and accurately reconstructing their flux and position. We also estimate the systematic errors introduced by the analysis and discuss the results in relation to the generation of candidate science alerts.

astro-ph.HE↗

arXiv2025

The new architecture design of the Science Alert Generation pipeline of the Cherenkov Telescope Array Observatory

The Cherenkov Telescope Array Observatory (CTAO) represents the next-generation gamma-ray observatory and will operate for several decades. It will be particularly suited to analyse transients and variable phenomena, which will trigger real-time scientific alerts. To support this, the Science Alert Generation (SAG) pipeline within the Array Control and Data Acquisition (ACADA) system will process data from telescope arrays in real time, using dedicated pipelines for data reconstruction (SAG-RECO), data quality monitoring (SAG-DQ) and science monitoring (SAG-SCI). The Supervisor (SAG-SUP) oversees the dynamic operations of SAG and its integration with other ACADA components. SAG is designed to issue candidate science alerts within 20 s of data availability, processing events on multiple time scales (seconds to hours) and handling trigger rates of tens of kHz. Meeting these requirements necessitates optimised software and hardware architectures. This work presents recent developments in SAG's architecture, aimed at two main challenges: (1) selecting data only from telescopes that have entered a stable tracking state, even when they begin tracking at different times during multi-telescope observations, and (2) incorporating environmental and system monitoring information to ensure high data quality. SAG-SUP can retrieve real-time telescope status and environmental conditions from telescope managers and the weather station through the ACADA Monitoring system, collect them in a database and then use them to filter out data from slewing phases or degraded conditions. These enhancements are crucial to ensure the reliability of science alerts and improve the overall performance and responsiveness of the CTAO real-time analysis framework.

astro-ph.IM↗

arXiv2025

Solar Flare Hard X-ray Polarimetry with the CUbesat Solar Polarimeter (CUSP) mission

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission planned for a launch in low-Earth orbit and aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. It is undergoing a 12-month Phase B that started in December 2024. The Compton polarimeter on board CUSP is composed of two acquisition chains based on plastic scintillators read out by Multi-Anode PhotoMultiplier Tubes for the scatterer part and GAGG crystals coupled to Avalanche PhotoDiodes for the absorbers. An event coincident between the two readout schemes will lead to a measurement of the incoming X-ray's azimuthal scattering angle, linked to the polarization of the solar flare in a statistical manner. The current status of the CUSP mission design, mission analysis, and payload scientific performance will be reported. The latter will be discussed based on preliminary laboratory results obtained in parallel with Geant4 simulations.

astro-ph.SR↗

arXiv2025

The multi-physics analysis, design and testing of CUSP, a CubeSat mission for space weather and solar flares x-ray polarimetry

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. As part of CUSP's Phase B study, which began in December 2024 and will last one year, we present the current development status of the design solutions adopted for the mission's most critical multi-physics design drivers. These solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. In particular, we describe the mechanical design of each structural component, the results of static, dynamic finite element analyses, and a proposal for topological optimization of the interface between the platform and payload and some fixture for test, and the preliminary environmental testing campaign (e.g., vibration, shock) that will be carried out on a mechanical demonstrator.

astro-ph.IM↗

arXiv2025

The CUbesat Solar Polarimeter (CUSP): mission overview II

The CUbesat Solar Polarimeter (CUSP) project is an Earth-orbiting CubeSat mission designed to measure the linear polarization of solar flares in the hard X-ray band using a Compton scattering polarimeter. CUSP will enable the study of magnetic reconnection and particle acceleration within the Sun's flaring magnetic structures. This project is being developed within the framework of the Italian Space Agency's Alcor Program, which aims to foster new CubeSat missions. CUSP entered its Phase B in December 2024, a phase scheduled to last 12 months. This paper reports on the current status of the CUSP mission design, mission analysis, and payload scientific performance.

astro-ph.SR↗

arXiv2025

CUbesat Solar Polarimeter (CUSP) Sensitivity Estimation and Performance Optimization using Geant4

The CUbesat Solar Polarimeter (CUSP) aims to measure the linear polarization of solar flares in the 25-100 keV X-ray band using a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star by providing high-sensitivity polarization measurements. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, which began in December 2024 and will continue for one year, we present the development status of the Geant4 based simulator to accurately simulate the detectors response and initial results on the sensitivity of the instrument. Geant4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. We implemented a detailed CUSP Mass Model within Geant4 to simulate and estimate the instruments sensitivity, correcting the geometric effects of the instrument. We also evaluated the effect of backscattering shielding on the sensitivity to optimize the mass model of the instrument.

astro-ph.SR↗

arXiv2025

Prototype Development and Calibration of the CUbesat Solar Polarimeter (CUSP)

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It has been proposed as a constellation of a two Cubesat mission to monitor the Sun for Space Weather, and will proceed with a single-satellite asset in its baseline implementation. In the frame of CUSP's Phase B study, that started in December 2024 for a 1-year period, we present the development status of this dual-phase polarimeter. Preliminary laboratory results using two chains of acquisition will be discussed. The first chain of acquisition, based on the Hamamatsu R7600 multi-anode photomultiplier tubes coupled to plastic scintillator bars and read out by the MAROC-3A ASIC, is used to detect the Compton scattering of incoming photons. On the other hand, GAGG crystals coupled to avalanche photo-diodes with a readout based on the SKIROC-2A ASIC are used to absorb the scattered photons. By reconstructing the azimuthal scattering direction for many incoming photons, one can infer the linear polarization degree and angle of the source. We will discuss the calibration results obtained with our prototype detector by using well-known radioactive isotopes, allowing us to assess the performances of our detector over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2025

Study of the HV power supply modules for the CUbesat Solar Polarimeter (CUSP)

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. CUSP undergoing the Phase B started in December 2024 that will last for 12 month. The Compton polarimeter of the CUSP payload performs coincidence measurements between plastic scintilaltors and GaGG(Ce) crystals to derive the polarization of X-rays. These sensors are readout by Multi Anode Photomultiplier Tubes (MAPMTs) and Avalanche Photodiodes (APDs) respectively. Both sensors need an HV power supply up to -1~kV (for the MAPMT) and +500~V (for the APD). We tested precision regulated High Voltage DC/DC Converters by HVM Technology Inc. with Sub-Miniature Case Size ($0.85''\times0.85''\times0.60''$) of the SMHV series. These modules are compact and suited for CubeSat missions.

astro-ph.IM↗

arXiv2024

The evaluation of the CUSP scientific performance by a GEANT4 Monte Carlo simulation

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It is approved for a Phase B study. In this work, we report on the accurate simulation of the detector's response to evaluate the scientific performance. A GEANT4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. Using this approach, we implemented a detailed CUSP Mass Model. In this work, we report on the evaluation of the detector's effective area as a function of the beam energy.

astro-ph.IM↗

arXiv2024

The multi$-$physics analysis and design of CUSP, a two CubeSat constellation for Space Weather and Solar flares X-ray polarimetry

The CUbesat Solar Polarimeter (CUSP) project aims to develop a constellation of two CubeSats orbiting the Earth to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter on board of each satellite. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures. CUSP is a project approved for a Phase B study by the Italian Space Agency in the framework of the Alcor program aimed to develop CubeSat technologies and missions. In this paper we describe the a method for a multi-physical simulation analysis while analyzing some possible design optimization of the payload design solutions adopted. In particular, we report the mechanical design for each structural component, the results of static and dynamic finite element analysis, the preliminary thermo-mechanical analysis for two specific thermal cases (hot and cold orbit) and a topological optimization of the interface between the platform and the payload.

astro-ph.IM↗

arXiv2024

The CUbesat Solar Polarimeter (CUSP) mission overview

The CUbesat Solar Polarimeter (CUSP) project is a future CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band, by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. The project is in the framework of the Italian Space Agency Alcor Program, which aims to develop new CubeSat missions. CUSP is approved for a Phase B study that will last for 12 months, starting in mid-2024. We report on the current status of the CUSP mission project as the outcome of the Phase A.

astro-ph.IM↗

arXiv2022

Combined X-ray and optical analysis to probe the origin of the plateau emission in $γ$-ray bursts afterglows

A large fraction of gamma-ray bursts (GRBs) shows a plateau phase during the X-ray afterglow emission, whose physical origin is still debated. In this work we define a sample of 30 GRBs with simultaneous X-ray and optical data during and after the plateau phase. Through a time-resolved spectral analysis of the X-ray plateaus, we test the consistency of the unabsorbed optical fluxes with those obtained via X-ray-to-optical spectral extrapolation by assuming a synchrotron spectrum. Combining X-ray with optical data, we find that 63% (19/30) GRBs are compatible with a single synchrotron spectrum thus suggesting that both the optical and X-ray radiations are produced from a single emitting region. For these GRBs we derive the temporal evolution of the break frequency and we compare it with the expectations predicted by several models. For 11/30 GRBs the optical emission is above the predicted range of values extrapolated from the X-rays in at least one temporal bin of the light curve. These GRBs may not be explained with a single zone emission, indicating the necessity of invoking two cooperating processes in order to explain the broad band spectral behaviour during X-ray plateaus. We discuss our findings in the framework of different scenarios invoked to explain the plateau feature, including the energy injection from a spinning-down magnetar and the high latitude emission from a structured jet.

astro-ph.HE↗

arXiv2022

CUSP: a two cubesats constellation for Space Weather and solar flares X-ray polarimetry

The CUbesat Solar Polarimeter (CUSP) project aims to develop a constellation of two CubeSats orbiting the Earth to measure the linear polarisation of solar flares in the hard X-ray band by means of a Compton scattering polarimeter on board of each satellite. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures. CUSP is a project approved for a Phase A study by the Italian Space Agency in the framework of the Alcor program aimed to develop CubeSat technologies and missions.

astro-ph.SR↗

arXiv2021

rta-dq-lib: a software library to perform online data quality analysis of scientific data

The Cherenkov Telescope Array (CTA) is an initiative that is currently building the largest gamma-ray ground Observatory that ever existed. A Science Alert Generation (SAG) system, part of the Array Control and Data Acquisition (ACADA) system of the CTA Observatory, analyses online the telescope data - arriving at an event rate of tens of kHz - to detect transient gamma-ray events. The SAG system also performs an online data quality analysis to assess the instruments' health during the data acquisition: this analysis is crucial to confirm good detections. A Python and a C++ software library to perform the online data quality analysis of CTA data, called rta-dq-lib, has been proposed for CTA. The Python version is dedicated to the rapid prototyping of data quality use cases. The C++ version is optimized for maximum performance. The library allows the user to define, through XML configuration files, the format of the input data and, for each data field, which quality checks must be performed and which types of aggregations and transformations must be applied. It internally translates the XML configuration into a direct acyclic computational graph that encodes the dependencies of the computational tasks to be performed. This model allows the library to easily take advantage of parallelization at the thread level and the overall flexibility allow us to develop generic data quality analysis pipelines that could also be reused in other applications.

astro-ph.IM↗