arXiv subjects

Giovanni Marsella

Publications and source records attributed to Giovanni Marsella.

14 recordsLinked to original sources

arXiv2025

Design and Performance of the Upgraded Prototype Schwarzschild-Couder Telescope Camera Module

The Cherenkov Telescope Array Observatory (CTAO) is a ground-based observatory that will improve upon the sensitivities of the current generation of very-high-energy gamma-ray instruments. The Schwarzschild-Couder Telescope (SCT) is a dual-mirror candidate design for a CTAO Medium-Sized Telescope (MST). The prototype Schwarzschild-Couder Telescope (pSCT) was inaugurated in 2019 at Fred Lawrence Whipple Observatory (FLWO) in Arizona and observed significant gamma-ray emission from the Crab Nebula with a partially populated camera. The pSCT camera is currently being upgraded to fully instrument the focal plane with 11,328 silicon photomultiplier (SiPM) pixels split between 177 camera modules. Additionally, the modules will feature upgraded electronics designed to reduce electronics crosstalk and noise. A module calibration procedure has been developed using a preproduction test module. Following this calibration procedure, performance testing shows that the upgrade module has low noise, minimal electronics crosstalk, and excellent charge resolution. After calibration and optimization, the 177 production modules will be installed in the pSCT camera for commissioning. This will be followed by observations of known VHE gamma-ray sources for camera performance validation.

astro-ph.IM↗

arXiv2025

Charge-dependent spectral softenings of primary cosmic-rays below the knee

In most particle acceleration or propagation theories, the characteristic features of the cosmic ray spectra due to acceleration limits or propagation phase changes are charge dependent. Alternatively, the interaction scenario would expect mass dependent spectral features in general. The observational verification of which relation takes effect in nature is still lack due to the difficulty of measuring the spectra of individual particles up to very high energies. Here we report direct measurements of the carbon, oxygen, and iron spectra from ~20 gigavolts to ~100 teravolts (~60 teravolts for iron) with 9 years of on-orbit data collected by the Dark Matter Particle Explorer. Distinct spectral softenings have been directly detected in these spectra for the first time. Combined with the updated proton and helium spectra, the spectral softening appears universally at a rigidity of ~15 teravolts. A nuclei mass dependent softening is rejected at a confidence level of >99.999%. Possible interpretations of these results, including a nearby cosmic ray source and other models such as the propagation effect, are discussed.

astro-ph.HE↗

arXiv2025

Investigating the capability of the Cherenkov Telescope Array Observatory to detect gamma-ray emission from simulated stationary neutrino sources identified by KM3NeT

The simultaneous observation of gamma rays and neutrinos from the same astrophysical source offers a unique opportunity to probe particle acceleration and interaction mechanisms in ultra-high-energy environments. The Cherenkov Telescope Array Observatory (CTAO) is a next-generation ground-based gamma-ray facility, sensitive to energies from 20~GeV to 300~TeV. In this work, we present for the first time a performance study of CTAO based on joint simulations of steady-state sources emitting both neutrinos and gamma rays, under the assumption that neutrino events are detected by the KM3NeT telescope in the Northern Hemisphere. To identify potentially observable sources, we apply a neutrino-based selection filter according to KM3NeT's discovery potential. We then simulate gamma-ray detectability with CTAO, taking into account visibility, sensitivity, and extragalactic background light absorption. The analysis is specifically focused on exploring the detectability of sources at low neutrino luminosities, limited to values below $10^{52}\,\mathrm{erg\,yr^{-1}}$, in order to assess the performance of CTAO and KM3NeT in identifying faint extragalactic emitters. Particular attention is given to the strategic role of KM3NeT's geographic location, which provides access to Southern-sky sources, and to the impact of the planned CTA+ upgrade, which will enhance CTAO-South with Large-Sized Telescopes (LSTs). Our results highlight the importance of coordinated multi-messenger strategies between KM3NeT and CTAO to maximize the discovery potential of astrophysical neutrino sources.

astro-ph.HE↗

arXiv2025

MATHUSLA: An External Long-Lived Particle Detector to Maximize the Discovery Potential of the HL-LHC

We present the current status of the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle (LLP) detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA40 is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size, close proximity to the CMS interaction point and about 100 m of rock shielding from LHC backgrounds allows it to detect LLP production rates and lifetimes that are one to two orders of magnitude beyond the ultimate reach of the LHC main detectors. This provides unique sensitivity to many LLP signals that are highly theoretically motivated, due to their connection to the hierarchy problem, the nature of dark matter, and baryogenesis. Data taking is projected to commence with the start of HL-LHC operations. We summarize the new 40m design for the detector that was recently presented in the MATHUSLA Conceptual Design Report, alongside new realistic background and signal simulations that demonstrate high efficiency for the main target LLP signals in a background-free HL-LHC search. We argue that MATHUSLA's uniquely robust expansion of the HL-LHC physics reach is a crucial ingredient in CERN's mission to search for new physics and characterize the Higgs boson with precision.

physics.ins-det↗

arXiv2025

Conceptual Design Report for the MATHUSLA Long-Lived Particle Detector near CMS

We present the Conceptual Design Report (CDR) for the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size, close proximity to the CMS interaction point and about 100 m of rock shielding from HL-LHC backgrounds allows it to detect LLP production rates and lifetimes that are one to two orders of magnitude beyond the ultimate sensitivity of the HL-LHC main detectors for many highly motivated LLP signals. Data taking is projected to commence with the start of HL-LHC operations. We present a new 40m design for the detector: its individual scintillator bars and wavelength-shifting fibers, their organization into tracking layers, tracking modules, tower modules and the veto detector; define a high-level design for the supporting electronics, DAQ and trigger system, including supplying a hardware trigger signal to CMS to record the LLP production event; outline computing systems, civil engineering and safety considerations; and present preliminary cost estimates and timelines for the project. We also conduct detailed simulation studies of the important cosmic ray and HL-LHC muon backgrounds, implementing full track/vertex reconstruction and background rejection, to ultimately demonstrate high signal efficiency and $\ll 1$ background event in realistic LLP searches for the main physics targets at MATHUSLA. This sensitivity is robust with respect to detector design or background simulation details. Appendices provide various supplemental information.

physics.ins-det↗

arXiv2023

Recent Progress and Next Steps for the MATHUSLA LLP Detector

We report on recent progress and next steps in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC as part of the Snowmass 2021 process. Our understanding of backgrounds has greatly improved, aided by detailed simulation studies, and significant R&D has been performed on designing the scintillator detectors and understanding their performance. The collaboration is on track to complete a Technical Design Report, and there are many opportunities for interested new members to contribute towards the goal of designing and constructing MATHUSLA in time for HL-LHC collisions, which would increase the sensitivity to a large variety of highly motivated LLP signals by orders of magnitude.

hep-ex↗

arXiv2022

Search for gamma-ray spectral lines with the DArk Matter Particle Explorer

The DArk Matter Particle Explorer (DAMPE) is well suitable for searching for monochromatic and sharp $γ$-ray structures in the GeV$-$TeV range thanks to its unprecedented high energy resolution. In this work, we search for $γ$-ray line structures using five years of DAMPE data. To improve the sensitivity, we develop two types of dedicated data sets (including the BgoOnly data which is the first time to be used in the data analysis for the calorimeter-based gamma-ray observatories) and adopt the signal-to-noise ratio optimized regions of interest (ROIs) for different DM density profiles. No line signals or candidates are found between 10 and 300 GeV in the Galaxy. The constraints on the velocity-averaged cross section for $χχ\to γγ$ and the decay lifetime for $χ\to γν$, both at 95% confidence level, have been calculated and the systematic uncertainties have been taken into account. Comparing to the previous Fermi-LAT results, though DAMPE has an acceptance smaller by a factor of $\sim 10$, similar constraints on the DM parameters are achieved and below 100 GeV the lower limits on the decay lifetime are even stronger by a factor of a few. Our results demonstrate the potential of high-energy-resolution observations on dark matter detection.

astro-ph.HE↗

arXiv2022

Design and Performance of the Prototype Schwarzschild-Couder Telescope Camera

The prototype Schwarzschild-Couder Telescope (pSCT) is a candidate for a medium-sized telescope in the Cherenkov Telescope Array. The pSCT is based on a novel dual mirror optics design which reduces the plate scale and allows for the use of silicon photomultipliers as photodetectors. The prototype pSCT camera currently has only the central sector instrumented with 25 camera modules (1600 pixels), providing a 2.68$^{\circ}$ field of view (FoV). The camera electronics are based on custom TARGET (TeV array readout with GSa/s sampling and event trigger) application specific integrated circuits. Field programmable gate arrays sample incoming signals at a gigasample per second. A single backplane provides camera-wide triggers. An upgrade of the pSCT camera is in progress, which will fully populate the focal plane. This will increase the number of pixels to 11,328, the number of backplanes to 9, and the FoV to 8.04$^{\circ}$. Here we give a detailed description of the pSCT camera, including the basic concept, mechanical design, detectors, electronics, current status and first light.

astro-ph.IM↗

arXiv2021

Observations of Forbush Decreases of cosmic ray electrons and positrons with the Dark Matter Particle Explorer

The Forbush Decrease (FD) represents the rapid decrease of the intensities of charged particles accompanied with the coronal mass ejections (CMEs) or high-speed streams from coronal holes. It has been mainly explored with ground-based neutron monitors network which indirectly measure the integrated intensities of all species of cosmic rays by counting secondary neutrons produced from interaction between atmosphere atoms and cosmic rays. The space-based experiments can resolve the species of particles but the energy ranges are limited by the relative small acceptances except for the most abundant particles like protons and helium. Therefore, the FD of cosmic ray electrons and positrons have just been investigated by the PAMELA experiment in the low energy range ($<5$ GeV) with limited statistics. In this paper, we study the FD event occurred in September, 2017, with the electron and positron data recorded by the Dark Matter Particle Explorer. The evolution of the FDs from 2 GeV to 20 GeV with a time resolution of 6 hours are given. We observe two solar energetic particle events in the time profile of the intensity of cosmic rays, the earlier and weak one has not been shown in the neutron monitor data. Furthermore, both the amplitude and recovery time of fluxes of electrons and positrons show clear energy-dependence, which is important in probing the disturbances of the interplanetary environment by the coronal mass ejections.

astro-ph.HE↗

arXiv2020

Comparison of proton shower developments in the BGO calorimeter of the Dark Matter Particle Explorer between GEANT4 and FLUKA simulations

The DArk Matter Particle Explorer (DAMPE) is a satellite-borne detector for high-energy cosmic rays and $γ$-rays. To fully understand the detector performance and obtain reliable physical results, extensive simulations of the detector are necessary. The simulations are particularly important for the data analysis of cosmic ray nuclei, which relies closely on the hadronic and nuclear interactions of particles in the detector material. Widely adopted simulation softwares include the GEANT4 and FLUKA, both of which have been implemented for the DAMPE simulation tool. Here we describe the simulation tool of DAMPE and compare the results of proton shower properties in the calorimeter from the two simulation softwares. Such a comparison gives an estimate of the most significant uncertainties of our proton spectral analysis.

physics.ins-det↗

arXiv2020

The MATHUSLA Test Stand

The rate of muons from LHC $pp$ collisions reaching the surface above the ATLAS interaction point is measured and compared with expected rates from decays of $W$ and $Z$ bosons and $b$- and $c$-quark jets. In addition, data collected during periods without beams circulating in the LHC provide a measurement of the background from cosmic ray inelastic backscattering that is compared to simulation predictions. Data were recorded during 2018 in a 2.5 $\times$ 2.5 $\times$ 6.5~$\rm{m}^3$ active volume MATHUSLA test stand detector unit consisting of two scintillator planes, one at the top and one at the bottom, which defined the trigger, and six layers of RPCs between them, grouped into three $(x,y)$-measuring layers separated by 1.74 m from each other. Triggers selecting both upward-going tracks and downward-going tracks were used.

physics.ins-det↗

arXiv2020

An Update to the Letter of Intent for MATHUSLA: Search for Long-Lived Particles at the HL-LHC

We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m in height. Engineering studies have been made in order to locate much of the decay volume below ground, bringing the detector even closer to the IP. With these changes, a 100 m x 100 m detector has the same physics reach for large c$τ$ as the 200 m x 200 m detector described in the LoI and other studies. The performance for small c$τ$ is improved because of the proximity to the IP. Detector technology has also evolved while retaining the strip-like sensor geometry in Resistive Plate Chambers (RPC) described in the LoI. The present design uses extruded scintillator bars read out using wavelength shifting fibers and silicon photomultipliers (SiPM). Operations will be simpler and more robust with much lower operating voltages and without the use of greenhouse gases. Manufacturing is straightforward and should result in cost savings. Understanding of backgrounds has also significantly advanced, thanks to new simulation studies and measurements taken at the MATHUSLA test stand operating above ATLAS in 2018. We discuss next steps for the MATHUSLA collaboration, and identify areas where new members can make particularly important contributions.

physics.ins-det↗

arXiv2019

MATHUSLA: A Detector Proposal to Explore the Lifetime Frontier at the HL-LHC

The observation of long-lived particles at the LHC would reveal physics beyond the Standard Model, could account for the many open issues in our understanding of our universe, and conceivably point to a more complete theory of the fundamental interactions. Such long-lived particle signatures are fundamentally motivated and can appear in virtually every theoretical construct that address the Hierarchy Problem, Dark Matter, Neutrino Masses and the Baryon Asymmetry of the Universe. We describe in this document a large detector, MATHUSLA, located on the surface above an HL-LHC $pp$ interaction point, that could observe long-lived particles with lifetimes up to the Big Bang Nucleosynthesis limit of 0.1 s. We also note that its large detector area allows MATHUSLA to make important contributions to cosmic ray physics. Because of the potential for making a major breakthrough in our conceptual understanding of the universe, long-lived particle searches should have the highest level of priority.

hep-ex↗

arXiv2018

A Letter of Intent for MATHUSLA: a dedicated displaced vertex detector above ATLAS or CMS

In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particles (LLPs) with up to several orders of magnitude better sensitivity than ATLAS or CMS, while also acting as a cutting-edge cosmic ray telescope at CERN to explore many open questions in cosmic ray and astro-particle physics. We review the physics motivations for MATHUSLA and summarize its LLP reach for several different possible detector geometries, as well as outline the cosmic ray physics program. We present several updated background studies for MATHUSLA, which help inform a first detector-design concept utilizing modular construction with Resistive Plate Chambers (RPCs) as the primary tracking technology. We present first efficiency and reconstruction studies to verify the viability of this design concept, and we explore some aspects of its total cost. We end with a summary of recent progress made on the MATHUSLA test stand, a small-scale demonstrator experiment currently taking data at CERN Point 1, and finish with a short comment on future work.

physics.ins-det↗