arXiv subjects

Guangji Chen

Publications and source records attributed to Guangji Chen.

36 records · Page 2Linked to original sources

arXiv2025

Static IRS Meets Distributed MIMO: A New Architecture for Dynamic Beamforming

Intelligent reflecting surface (IRS) has been considered as a revolutionary technology to enhance the wireless communication performance. To cater for multiple mobile users, adjusting IRS beamforming patterns over time, i.e., dynamic IRS beamforming (DIBF), is generally needed for achieving satisfactory performance, which results in high controlling power consumption and overhead. To avoid such cost, we propose a new architecture based on the static regulated IRS for wireless coverage enhancement, where the principle of distributed multiple-input multiple-output (D-MIMO) is integrated into the system to exploite the diversity of spatial directions provided by multiple access points (APs). For this new D-MIMO empowered static IRS architecture, the total target area is partitioned into several subareas and each subarea is served by an assigned AP. We consider to maximize the worst-case received power over all locations in the target area by jointly optimizing a single set of IRS beamforming pattern and AP-subarea association. Then, a two-step algorithm is proposed to obtain its high-quality solution. Theoretical analysis unveils that the fundamental squared power gain can still be achieved over all locations in the target area. The performance gap relative to the DIBF scheme is also analytically quantified. Numerical results validate our theoretical findings and demonstrate the effectiveness of our proposed design over benchmark schemes.

cs.IT↗

arXiv2024

Intelligent Reflecting Surface Aided MIMO Networks: Distributed or Centralized Architecture?

We investigate the capacity of a broadcast channel with a multi-antenna base station (BS) sending independent messages to multiple users, aided by IRSs with N elements. In particular, both the distributed and centralized IRS deployment architectures are considered. Regarding the distributed IRS, the N IRS elements form multiple IRSs and each of them is installed near a user cluster; while for the centralized IRS, all IRS elements are located in the vicinity of the BS. To draw essential insights, we first derive the maximum capacity achieved by the distributed IRS and centralized IRS, respectively, under the assumption of line-of-sight propagation and homogeneous channel setups. By capturing the fundamental tradeoff between the spatial multiplexing gain and passive beamforming gain, we rigourously prove that the capacity of the distributed IRS is higher than that of the centralized IRS provided that the total number of IRS elements is above a threshold. Motivated by the superiority of the distributed IRS, we then focus on the transmission and element allocation design under the distributed IRS. By exploiting the user channel correlation of intra-clusters and inter-clusters, an efficient hybrid multiple access scheme relying on both spatial and time domains is proposed to fully exploit both the passive beamforming gain and spatial DoF. Moreover, the IRS element allocation problem is investigated for the objectives of sum-rate maximization and minimum user rate maximization, respectively. Finally, extensive numerical results are provided to validate our theoretical finding and also to unveil the effectiveness of the distributed IRS for improving the system capacity under various system setups.

cs.IT↗

arXiv2024

Network-Level Integrated Sensing and Communication: Interference Management and BS Coordination Using Stochastic Geometry

In this work, we study integrated sensing and communication (ISAC) networks with the aim of effectively balancing sensing and communication (S&C) performance at the network level. Focusing on monostatic sensing, the tool of stochastic geometry is exploited to capture the S&C performance, which facilitates us to illuminate key cooperative dependencies in the ISAC network and optimize key network-level parameters. Based on the derived tractable expression of area spectral efficiency (ASE), we formulate the optimization problem to maximize the network performance from the view point of two joint S&C metrics. Towards this end, we further jointly optimize the cooperative BS cluster sizes for S&C and the serving/probing numbers of users/targets to achieve a flexible tradeoff between S&C at the network level. It is verified that interference nulling can effectively improve the average data rate and radar information rate. Surprisingly, the optimal communication tradeoff for the case of the ASE maximization tends to employ all spacial resources towards multiplexing and diversity gain, without interference nulling. By contrast, for the sensing objectives, resource allocation tends to eliminate certain interference especially when the antenna resources are sufficient, because the inter-cell interference becomes a more dominant factor affecting sensing performance. Furthermore, we prove that the ratio of the optimal number of users and the number of transmit antennas is a constant value when the communication performance is optimal. Simulation results demonstrate that the proposed cooperative ISAC scheme achieves a substantial gain in S&C performance at the network level.

cs.IT↗

arXiv2024

Spatial Multiplexing Oriented Channel Reconfiguration in Multi-IRS Aided MIMO Systems

Spatial multiplexing plays a significant role in improving the capacity of multiple-input multiple-output (MIMO) communication systems. To improve the spectral efficiency (SE) of a point-to-point MIMO system, we exploit the channel reconfiguration capabilities provided by multiple intelligent reflecting surfaces (IRSs) to enhance the spatial multiplexing. Unlike most existing works, we address both the issues of the IRSs placement and elements allocation. To this end, we first introduce an orthogonal placement strategy to mitigate channel correlation, thereby enabling interference-free multi-stream transmission. Subsequently, we propose a successive convex approximation (SCA)-based approach to jointly optimize the IRS elements and power allocation. Our theoretical analysis unveils that equal IRS elements/power allocation scheme becomes asymptotically optimal as the number of IRS elements and transmit power tend to be infinite. Numerical results demonstrate that when the total number of IRS elements or the power exceeds a certain threshold, a multi-IRS assisted system outperforms a single IRS configuration.

cs.IT↗

arXiv2024

Blockchain-aided wireless federated learning: Resource allocation and client scheduling

Federated learning (FL) based on the centralized design faces both challenges regarding the trust issue and a single point of failure. To alleviate these issues, blockchain-aided decentralized FL (BDFL) introduces the decentralized network architecture into the FL training process, which can effectively overcome the defects of centralized architecture. However, deploying BDFL in wireless networks usually encounters challenges such as limited bandwidth, computing power, and energy consumption. Driven by these considerations, a dynamic stochastic optimization problem is formulated to minimize the average training delay by jointly optimizing the resource allocation and client selection under the constraints of limited energy budget and client participation. We solve the long-term mixed integer non-linear programming problem by employing the tool of Lyapunov optimization and thereby propose the dynamic resource allocation and client scheduling BDFL (DRC-BDFL) algorithm. Furthermore, we analyze the learning performance of DRC-BDFL and derive an upper bound for convergence regarding the global loss function. Extensive experiments conducted on SVHN and CIFAR-10 datasets demonstrate that DRC-BDFL achieves comparable accuracy to baseline algorithms while significantly reducing the training delay by 9.24% and 12.47%, respectively.

cs.DC↗

arXiv2024

Intelligent Reflecting Surface Aided AirComp: Multi-Timescale Design and Performance Analysis

The integration of intelligent reflecting surface (IRS) into over-the-air computation (AirComp) is an effective solution for reducing the computational mean squared error (MSE) via its high passive beamforming gain. Prior works on IRS aided AirComp generally rely on the full instantaneous channel state information (I-CSI), which is not applicable to large-scale systems due to its heavy signalling overhead. To address this issue, we propose a novel multi-timescale transmission protocol. In particular, the receive beamforming at the access point (AP) is pre-determined based on the static angle information and the IRS phase-shifts are optimized relying on the long-term statistical CSI. With the obtained AP receive beamforming and IRS phase-shifts, the effective low-dimensional I-CSI is exploited to determine devices' transmit power in each coherence block, thus substantially reducing the signalling overhead. Theoretical analysis unveils that the achievable MSE scales on the order of ${\cal O}\left( {K/\left( {{N^2}M} \right)} \right)$, where $M$, $N$, and $K$ are the number of AP antennas, IRS elements, and devices, respectively. We also prove that the channel-inversion power control is asymptotically optimal for large $N$, which reveals that the full power transmission policy is not needed for lowering the power consumption of energy-limited devices.

cs.IT↗

arXiv2024

Deploying Graph Neural Networks in Wireless Networks: A Link Stability Viewpoint

As an emerging artificial intelligence technology, graph neural networks (GNNs) have exhibited promising performance across a wide range of graph-related applications. However, information exchanges among neighbor nodes in GNN pose new challenges in the resource-constrained scenario, especially in wireless systems. In practical wireless systems, the communication links among nodes are usually unreliable due to wireless fading and receiver noise, consequently resulting in performance degradation of GNNs. To improve the learning performance of GNNs, we aim to maximize the number of long-term average (LTA) communication links by the optimized power control under energy consumption constraints. Using the Lyapunov optimization method, we first transform the intractable long-term problem into a deterministic problem in each time slot by converting the long-term energy constraints into the objective function. In spite of this non-convex combinatorial optimization problem, we address this problem via equivalently solving a sequence of convex feasibility problems together with a greedy based solver. Simulation results demonstrate the superiority of our proposed scheme over the baselines.

cs.DC↗

arXiv2024

3D Multi-Target Localization Via Intelligent Reflecting Surface: Protocol and Analysis

With the emerging environment-aware applications, ubiquitous sensing is expected to play a key role in future networks. In this paper, we study a 3-dimensional (3D) multi-target localization system where multiple intelligent reflecting surfaces (IRSs) are applied to create virtual line-of-sight (LoS) links that bypass the base station (BS) and targets. To fully unveil the fundamental limit of IRS for sensing, we first study a single-target-single-IRS case and propose a novel \textit{two-stage localization protocol} by controlling the on/off state of IRS. To be specific, in the IRS-off stage, we derive the Cramér-Rao bound (CRB) of the azimuth/elevation direction-of-arrival (DoA) of the BS-target link and design a DoA estimator based on the MUSIC algorithm. In the IRS-on stage, the CRB of the azimuth/elevation DoA of the IRS-target link is derived and a simple DoA estimator based on the on-grid IRS beam scanning method is proposed. Particularly, the impact of echo signals reflected by IRS from different paths on sensing performance is analyzed. Moreover, we prove that the single-beam of the IRS is not capable of sensing, but it can be achieved with \textit{multi-beam}. Based on the two obtained DoAs, the 3D single-target location is constructed. We then extend to the multi-target-multi-IRS case and propose an \textit{IRS-adaptive sensing protocol} by controlling the on/off state of multiple IRSs, and a multi-target localization algorithm is developed. Simulation results demonstrate the effectiveness of our scheme and show that sub-meter-level positioning accuracy can be achieved.

cs.IT↗

arXiv2024

BS Coordination Optimization in Integrated Sensing and Communication: A Stochastic Geometric View

In this study, we explore integrated sensing and communication (ISAC) networks to strike a more effective balance between sensing and communication (S&C) performance at the network scale. We leverage stochastic geometry to analyze the S&C performance, shedding light on critical cooperative dependencies of ISAC networks. According to the derived expressions of network performance, we optimize the user/target loads and the cooperative base station cluster sizes for S&C to achieve a flexible trade-off between network-scale S&C performance. It is observed that the optimal strategy emphasizes the full utilization of spatial resources to enhance multiplexing and diversity gain when maximizing communication ASE. In contrast, for sensing objectives, parts of spatial resources are allocated to cancel inter-cell sensing interference to maximize sensing ASE. Simulation results validate that the proposed ISAC scheme realizes a remarkable enhancement in overall S&C network performance.

cs.IT↗

arXiv2023

Intelligent Reflecting Surface Aided Multi-Tier Hybrid Computing

The digital twin edge network (DITEN) aims to integrate mobile edge computing (MEC) and digital twin (DT) to provide real-time system configuration and flexible resource allocation for the sixth-generation network. This paper investigates an intelligent reflecting surface (IRS)-aided multi-tier hybrid computing system that can achieve mutual benefits for DT and MEC in the DITEN. For the first time, this paper presents the opportunity to realize the network-wide convergence of DT and MEC. In the considered system, specifically, over-the-air computation (AirComp) is employed to monitor the status of the DT system, while MEC is performed with the assistance of DT to provide low-latency computing services. Besides, the IRS is utilized to enhance signal transmission and mitigate interference among heterogeneous nodes. We propose a framework for designing the hybrid computing system, aiming to maximize the sum computation rate under communication and computation resources constraints. To tackle the non-convex optimization problem, alternative optimization and successive convex approximation techniques are leveraged to decouple variables and then transform the problem into a more tractable form. Simulation results verify the effectiveness of the proposed algorithm and demonstrate the IRS can significantly improve the system performance with appropriate phase shift configurations. Moreover, the results indicate that the DT assisted MEC system can precisely achieve the balance between local computing and task offloading since real-time system status can be obtained with the help of DT.

eess.SP↗

arXiv2023

Hybrid Active-Passive IRS Assisted Energy-Efficient Wireless Communication

Deploying active reflecting elements at the intelligent reflecting surface (IRS) increases signal amplification capability but incurs higher power consumption. Therefore, it remains a challenging and open problem to determine the optimal number of active/passive elements for maximizing energy efficiency (EE). To answer this question, we consider a hybrid active-passive IRS (H-IRS) assisted wireless communication system, where the H-IRS consists of both active and passive reflecting elements.Specifically, we study the optimization of the number of active/passive elements at the H-IRS to maximize EE. To this end, we first derive the closed-form expression for a near-optimal solution under the line-of-sight (LoS) channel case and obtain its optimal solution under the Rayleigh fading channel case. Then, an efficient algorithm is employed to obtain a high-quality sub-optimal solution for the EE maximization under the general Rician channel case. Simulation results demonstrate the effectiveness of the H-IRS for maximizing EE under different Rician factors and IRS locations.

cs.IT↗

arXiv2023

Delay-aware Multiple Access Design for Intelligent Reflecting Surface Aided Uplink Transmission

In this paper, we develop a hybrid multiple access (MA) protocol for an intelligent reflecting surface (IRS) aided uplink transmission network by incorporating the IRS-aided time-division MA (I-TDMA) protocol and the IRS-aided non-orthogonal MA (I-NOMA) protocol as special cases. Two typical communication scenarios, namely the transmit power limited case and the transmit energy limited case are considered, where the device's rearranged order, time and power allocation, as well as dynamic IRS beamforming patterns over time are jointly optimized to minimize the sum transmission delay. To shed light on the superiority of the proposed IRS-aided hybrid MA (I-HMA) protocol over conventional protocols, the conditions under which I-HMA outperforms I-TDMA and I-NOMA are revealed by characterizing their corresponding optimal solution. Then, a computationally efficient algorithm is proposed to obtain the high-quality solution to the corresponding optimization problems. Simulation results validate our theoretical findings, demonstrate the superiority of the proposed design, and draw some useful insights. Specifically, it is found that the proposed protocol can significantly reduce the sum transmission delay by combining the additional gain of dynamic IRS beamforming with the high spectral efficiency of NOMA, which thus reveals that integrating IRS into the proposed HMA protocol is an effective solution for delay-aware optimization. Furthermore, it reveals that the proposed design reduces the time consumption not only from the system-centric view, but also from the device-centric view.

cs.IT↗

arXiv2023

Fundamental Limits of Intelligent Reflecting Surface Aided Multiuser Broadcast Channel

Intelligent reflecting surface (IRS) has recently received significant attention in wireless networks owing to its ability to smartly control the wireless propagation through passive reflection. Although prior works have employed the IRS to enhance the system performance under various setups, the fundamental capacity limits of an IRS aided multi-antenna multi-user system have not yet been characterized. Motivated by this, we investigate an IRS aided multiple-input single-output (MISO) broadcast channel by considering the capacity-achieving dirty paper coding (DPC) scheme and dynamic beamforming configurations. We first propose a bisection based framework to characterize its capacity region by optimally solving the sum-rate maximization problem under a set of rate constraints, which is also applicable to characterize the achievable rate region with the zero-forcing (ZF) scheme. Interestingly, it is rigorously proved that dynamic beamforming is able to enlarge the achievable rate region of ZF if the IRS phase-shifts cannot achieve fully orthogonal channels, whereas the attained gains become marginal due to the reduction of the channel correlations induced by smartly adjusting the IRS phase-shifts. The result implies that employing the IRS is able to reduce the demand for implementing dynamic beamforming. Finally, we analytically prove that the sum-rate achieved by the IRS aided ZF is capable of approaching that of the IRS aided DPC with a sufficiently large IRS in practice. Simulation results shed light on the impact of the IRS on transceiver designs and validate our theoretical findings, which provide useful guidelines to practical systems by indicating that replacing sophisticated schemes with easy-implementation schemes would only result in slight performance loss.

cs.IT↗

arXiv2022

IRS Aided MEC Systems with Binary Offloading: A Unified Framework for Dynamic IRS Beamforming

In this paper, we develop a unified dynamic intelligent reflecting surface (IRS) beamforming framework to boost the sum computation rate of an IRS-aided mobile edge computing (MEC) system, where each device follows a binary offloading policy. Specifically, the task of each device has to be either executed locally or offloaded to MEC servers as a whole with the aid of given number of IRS beamforming vectors available. By flexibly controlling the number of IRS reconfiguration times, the system can achieve a balance between the performance and associated signalling overhead. We aim to maximize the sum computation rate by jointly optimizing the computational mode selection for each device, offloading time allocation, and IRS beamforming vectors across time. Since the resulting optimization problem is non-convex and NP-hard, there are generally no standard methods to solve it optimally. To tackle this problem, we first propose a penalty-based successive convex approximation algorithm, where all the associated variables in the inner-layer iterations are optimized simultaneously and the obtained solution is guaranteed to be locally optimal. Then, we further derive the offloading activation condition for each device by deeply exploiting the intrinsic structure of the original optimization problem. According to the offloading activation condition, a low-complexity algorithm based on the successive refinement method is proposed to obtain high-quality solutions, which is more appealing for practical systems with a large number of devices and IRS elements. Moreover, the optimal condition for the proposed low-complexity algorithm is revealed. Numerical results demonstrate the effectiveness of our proposed algorithms and also unveil the fundamental performance-cost tradeoff of the proposed dynamic IRS beamforming framework.

cs.IT↗

arXiv2022

Active IRS Aided Multiple Access for Energy-Constrained IoT Systems

We investigate the fundamental multiple access (MA) scheme in an active intelligent reflecting surface (IRS) aided energy-constrained Internet-of-Things (IoT) system, where an active IRS is deployed to assist the uplink transmission from multiple IoT devices to an access point (AP). Our goal is to maximize the sum throughput by optimizing the IRS beamforming vectors across time and resource allocation. To this end, we first study two typical active IRS aided MA schemes, namely time division multiple access (TDMA) and non-orthogonal multiple access (NOMA), by analytically comparing their achievable sum throughput and proposing corresponding algorithms. Interestingly, we prove that given only one available IRS beamforming vector, the NOMA-based scheme generally achieves a larger throughput than the TDMA-based scheme, whereas the latter can potentially outperform the former if multiple IRS beamforming vectors are available to harness the favorable time selectivity of the IRS. To strike a flexible balance between the system performance and the associated signaling overhead incurred by more IRS beamforming vectors, we then propose a general hybrid TDMA-NOMA scheme with user grouping, where the devices in the same group transmit simultaneously via NOMA while devices in different groups occupy orthogonal time slots. By controlling the number of groups, the hybrid TDMA-NOMA scheme is applicable for any given number of IRS beamforming vectors available. Despite of the non-convexity of the considered optimization problem, we propose an efficient algorithm based on alternating optimization. Simulation results illustrate the practical superiorities of the active IRS over the passive IRS in terms of the coverage extension and supporting multiple energy-limited devices, and demonstrate the effectiveness of our proposed hybrid MA scheme for flexibly balancing the performance-cost tradeoff.

cs.IT↗

arXiv2021

IRS-aided Wireless Powered MEC Systems: TDMA or NOMA for Computation Offloading?

An intelligent reflecting surface (IRS)-aided wireless powered mobile edge computing (WP-MEC) system is conceived, where each device's computational task can be divided into two parts for local computing and offloading to mobile edge computing (MEC) servers, respectively. Both time division multiple access (TDMA) and non-orthogonal multiple access (NOMA) schemes are considered for uplink (UL) offloading. Given the capability of IRSs in intelligently reconfiguring wireless channels over time, it is fundamentally unknown which multiple access scheme is superior for MEC UL offloading. To answer this question, we first investigate the impact of three different dynamic IRS beamforming (DIBF) schemes on the computation rate of both offloading schemes, based on the flexibility for the IRS in adjusting its beamforming (BF) vector in each transmission frame. Under the DIBF framework, computation rate maximization problems are formulated for both the NOMA and TDMA schemes, respectively, by jointly optimizing the IRS passive BF and the resource allocation. We rigorously prove that offloading adopting TDMA can achieve the same computation rate as that of NOMA, when all the devices share the same IRS BF vector during the UL offloading. By contrast, offloading exploiting TDMA outperforms NOMA, when the IRS BF vector can be flexibly adapted for UL offloading. Despite the non-convexity of the computation rate maximization problems for each DIBF scheme associated with highly coupled optimization variables, we conceive computationally efficient algorithms by invoking alternating optimization. Our numerical results demonstrate the significant performance gains achieved by the proposed designs over various benchmark schemes.

cs.IT↗

arXiv2021

Throughput Analysis of UAV-assisted CellularNetworks by Matérn Hardcore Point Process

Unmanned aerial vehicles (UAVs) are expected to coexist with conventional terrestrial cellular networks and become an important component to support high rate transmissions. This paper presents an analytical framework for evaluating the throughput performance of a downlink two-tier heterogeneous network. Considering the minimum distance constraint among UAVs, Matérn hardcore point process (MHP) is utilized to model the locations of UAVs. The locations of terrestrial base stations (BSs) are modeled by Poisson point process (PPP). Tools of stochastic geometry are invoked to derive tractable expressions for average data rates of users. With the analytical results, we discuss the optimal combinations of UAVs' height and power control factor. The result shows that an appropriate power control factor can effectively maximize UAV users' average data rate as well as guaranteeing the BS users' performance under our proposed model.

cs.NI↗

arXiv2019

Analysis and Optimization of Random Cache in Multi-Antenna HetNets with Interference Nulling

From the perspective of statistical performance, this paper presents a framework for the per-user throughput analysis in random cache based multi-antenna heterogeneous networks (HetNets) with user-centric inter-cell interference nulling (IN). Using tools from stochastic geometry, an explicit expression for the per-user throughput is derived. Based on the analytical results, the optimal cache probabilities for maximizing the per-user throughput are analyzed. Theoretical analysis and numerical results reveal that the optimal random cache under interference nulling fully harvests the file diversity gain (FDG) and achieves a promising per-user throughput.

eess.SP↗