arXiv subjects

Harald Haas

Publications and source records attributed to Harald Haas.

At least 73 records · Page 4Linked to original sources

arXiv2020

Towards the Use of Re-configurable Intelligent Surfaces in VLC Systems: Beam Steering

The emergence of visible light communication (VLC) technology as a solution to solve radio frequency impediments, such as spectrum shortage, is continuously appealing. In addition to its large and unlicensed bandwidth, VLC provides a high level of security in a closed room with zero radio frequency interference. However, loss of the VLC signal is experienced when the receiver rotates or moves. This challenge requires a special solution for integration into portable devices. On the other hand, re-configurable intelligent surface (RIS) is a technology exploited in radio frequency to solve dead zones and loss of signal. RIS elements are characterized by tunable physico-chemical characteristics including physical depth and refractive index. In this paper, we exploit these RIS attributes to steer the incident light beam and offer the VLC receiver a large range of rotation angle while improving its signal detection capabilities. We show that instead of using convex, parabolic, or spherical lenses, adopting a meta-lens with artificial muscles or a thin-film crystal-liquid with embedded Titanium dioxide nano-disk, a VLC receiver can detect light rays at $90^o$ incidence angle with high precision and considerable improvement in the detected light intensity, even with a miniaturized single photodetector.

eess.SP↗

arXiv2020

End-to-End Energy Efficiency Evaluation for B5G Ultra Dense Networks

Energy efficiency (EE) is a major performance metric for fifth generation (5G) and beyond 5G (B5G) wireless communication systems, especially for ultra dense networks. This paper proposes an end-to-end (e2e) power consumption model and studies the energy efficiency for a heterogeneous B5G cellular architecture that separates the indoor and outdoor communication scenarios in ultra dense networks. In this work, massive multiple-input-multiple-output (MIMO) technologies at conventional sub-6 GHz frequencies are used for long-distance outdoor communications. Light-Fidelity (LiFi) and millimeter wave (mmWave) technologies are deployed to provide a high data rate service to indoor users. Whereas, in the referenced nonseparated system, the indoor users communicate with the outdoor massive MIMO macro base station directly. The performance of these two systems are evaluated and compared in terms of the total power consumption and energy efficiency. The results show that the network architecture which separates indoor and outdoor communication can support a higher data rate transmission for less energy consumption, compared to non-separate communication scenario. In addition, the results show that deploying LiFi and mmWave IAPs can enable users to transmit at a higher data rate and further improve the EE.

eess.SP↗

arXiv2020

Invoking Deep Learning for Joint Estimation of Indoor LiFi User Position and Orientation

Light-fidelity (LiFi) is a fully-networked bidirectional optical wireless communication (OWC) that is considered a promising solution for high-speed indoor connectivity. Unlike in conventional radio frequency wireless systems, the OWC channel is not isotropic, meaning that the device orientation affects the channel gain significantly. However, due to the lack of proper channel models for LiFi systems, many studies have assumed that the receiver is vertically upward and randomly located within the coverage area, which is not a realistic assumption from a practical point of view. In this paper, novel realistic and measurement-based channel models for indoor LiFi systems are proposed. Precisely, the statistics of the channel gain are derived for the case of randomly oriented stationary and mobile LiFi receivers. For stationary users, two channel models are proposed, namely, the modified truncated Laplace (MTL) model and the modified Beta (MB) model. For LiFi users, two channel models are proposed, namely, the sum of modified truncated Gaussian (SMTG) model and the sum of modified Beta (SMB) model. Based on the derived models, the impact of random orientation and spatial distribution of LiFi users is investigated, where we show that the aforementioned factors can strongly affect the channel gain and system performance.

eess.SP↗

arXiv2020

6G White paper: Research challenges for Trust, Security and Privacy

The roles of trust, security and privacy are somewhat interconnected, but different facets of next generation networks. The challenges in creating a trustworthy 6G are multidisciplinary spanning technology, regulation, techno-economics, politics and ethics. This white paper addresses their fundamental research challenges in three key areas. Trust: Under the current "open internet" regulation, the telco cloud can be used for trust services only equally for all users. 6G network must support embedded trust for increased level of information security in 6G. Trust modeling, trust policies and trust mechanisms need to be defined. 6G interlinks physical and digital worlds making safety dependent on information security. Therefore, we need trustworthy 6G. Security: In 6G era, the dependence of the economy and societies on IT and the networks will deepen. The role of IT and the networks in national security keeps rising - a continuation of what we see in 5G. The development towards cloud and edge native infrastructures is expected to continue in 6G networks, and we need holistic 6G network security architecture planning. Security automation opens new questions: machine learning can be used to make safer systems, but also more dangerous attacks. Physical layer security techniques can also represent efficient solutions for securing less investigated network segments as first line of defense. Privacy: There is currently no way to unambiguously determine when linked, deidentified datasets cross the threshold to become personally identifiable. Courts in different parts of the world are making decisions about whether privacy is being infringed, while companies are seeking new ways to exploit private data to create new business revenues. As solution alternatives, we may consider blockchain, distributed ledger technologies and differential privacy approaches.

cs.CR↗

arXiv2020

Measurements-Based Channel Models for Indoor LiFi Systems

eess.SP↗

arXiv2020

Hybrid LiFi and WiFi Networks: A Survey

To tackle the rapidly growing number of mobile devices and their expanding demands for Internet services, network convergence is envisaged to integrate different technology domains. A recently proposed and promising approach to indoor wireless communications is integrating light fidelity (LiFi) and wireless fidelity (WiFi), namely a hybrid LiFi and WiFi network (HLWNet). This type of network combines the high-speed data transmission of LiFi and the ubiquitous coverage of WiFi. In this paper, we present a survey-style introduction to HLWNets, starting with a framework including the network structure, cell deployment, multiple access schemes, modulation techniques, illumination requirements and backhauling. Then, key performance metrics and recent achievements are reviewed. Further, the unique challenges faced by HLWNets are elaborated in many research directions, including user behavior modeling, interference management, handover and load balancing. Finally, we discuss the potential of HLWNets in application areas such as indoor positioning and physical layer security.

cs.IT↗

arXiv2019

OFDM-Based Optical Spatial Modulation

Spatial modulation (SM) has proven to be a promising multiple-input-multiple-output (MIMO) technique which provides high energy efficiency and reduces system complexity. In SM, only one transmitter is active at any given time while the rest of them remain silent. The index of the active transmitter carries information. This spatial information is in addition to the data carried by the constellation symbols in the signal domain. Therefore, SM increases the transmission rate of the communication system compared to single-input-single-output and space-time block coding (STBC)-MIMO. For signal domain data encoding, orthogonal frequency division multiplexing (OFDM) has been widely adopted. The key benefits in multi-carrier intensity-modulation and direct-detection (IM/DD) systems are: i) the capability to achieve high spectral efficiency and ii) the ability to effectively mitigate direct-current (DC) wander effects and the impact of ambient light. However, current off-the shelf light emitting diodes (LEDs) which are used as transmit entities are primarily bandwidth limited. Thus, there are benefits of combining SM and OFDM to enhance transmission speeds while maintaining low complexity. In this paper, the two most common OFDM-based SM types, namely frequency domain SM (FD-SM) and time domain SM (TD-SM), are investigated for optical wireless communications (OWC). Moreover, proof-ofconcept experimental results are presented to showcase practical feasibility of both techniques. The obtained results are also compared with Monte Carlo simulations. The results show that TDSM with an optimal maximum-a-posteriori-probability (MAP) detector significantly outperforms FD-SM. It can be inferred from the results that TD SM is a strong candidate among OFDM-based optical SM systems for future optical IM/DD wireless communication systems.

cs.IT↗

arXiv2019

Multi-Hop Wireless Optical Backhauling for LiFi Attocell Networks: Bandwidth Scheduling and Power Control

The backhaul of hundreds of light fidelity (LiFi) base stations (BSs) constitutes a major challenge. Indoor wireless optical backhauling is a novel approach whereby the interconnections between adjacent LiFi BSs are provided by way of directed line-of-sight (LOS) wireless infrared (IR) links. Building on the aforesaid approach, this paper presents the top-down design of a multi-hop wireless backhaul configuration for multi-tier optical attocell networks by proposing the novel idea of super cells. Such cells incorporate multiple clusters of attocells that are connected to the core network via a single gateway based on multi-hop decode-and-forward (DF) relaying. Consequently, new challenges arise for managing the bandwidth and power resources of the bottleneck backhaul. By putting forward user-based bandwidth scheduling (UBS) and cell-based bandwidth scheduling (CBS) policies, the system-level modeling and analysis of the end-to-end multi-user sum rate is elaborated. In addition, optimal bandwidth scheduling under both UBS and CBS policies are formulated as constrained convex optimization problems, which are solved by using the projected subgradient method. Furthermore, the transmission power of the backhaul system is opportunistically reduced by way of an innovative fixed power control (FPC) strategy. The notion of backhaul bottleneck occurrence (BBO) is introduced. An accurate approximate expression of the probability of BBO is derived, and then verified using Monte Carlo simulations. Several insights are provided into the offered gains of the proposed schemes through extensive computer simulations, by studying different aspects of the performance of super cells including the average sum rate, the BBO probability and the backhaul power efficiency (PE).

cs.IT↗

arXiv2019

Physical Layer Security for Visible Light Communication Systems: A Survey

Due to the dramatic increase in high data rate services and in order to meet the demands of the fifth-generation (5G) networks, researchers from both academia and industry are exploring advanced transmission techniques, new network architectures and new frequency spectrum such as the visible light spectra. Visible light communication (VLC) particularly is an emerging technology that has been introduced as a promising solution for 5G and beyond. Although VLC systems are more immune against interference and less susceptible to security vulnerabilities since light does not penetrate through walls, security issues arise naturally in VLC channels due to their open and broadcasting nature, compared to fiber-optic systems. In addition, since VLC is considered to be an enabling technology for 5G, and security is one of the 5G fundamental requirements, security issues should be carefully addressed and resolved in the VLC context. On the other hand, due to the success of physical layer security (PLS) in improving the security of radio-frequency (RF) wireless networks, extending such PLS techniques to VLC systems has been of great interest. Only two survey papers on security in VLC have been published in the literature. However, a comparative and unified survey on PLS for VLC from information theoretic and signal processing point of views is still missing. This paper covers almost all aspects of PLS for VLC, including different channel models, input distributions, network configurations, precoding/signaling strategies, and secrecy capacity and information rates. Furthermore, we propose a number of timely and open research directions for PLS-VLC systems, including the application of measurement-based indoor and outdoor channel models, incorporating user mobility and device orientation into the channel model, and combining VLC and RF systems to realize the potential of such technologies.

eess.SP↗

arXiv2019

Performance Analysis of SPAD-based OFDM

In this paper, an analytical approach for the nonlinear distorted bit error rate performance of optical orthogonal frequency division multiplexing (O-OFDM) with single photon avalanche diode (SPAD) receivers is presented. Major distortion effects of passive quenching (PQ) and active quenching (AQ) SPAD receivers are analysed in this study. The performance analysis of DC-biased O-OFDM and asymmetrically clipped O-OFDM with PQ and AQ SPAD are derived. The comparison results show the maximum optical irradiance caused by the nonlinear distortion, which limits the transmission power and bit rate. The theoretical maximum bit rate of SPAD-based OFDM is found which is up to 1~Gbits/s. This approach supplies a closed-form analytical solution for designing an optimal SPAD-based system.

cs.IT↗

arXiv2019

Performance Analysis of Non-DC-Biased OFDM

The performance analysis of a novel optical modulation scheme is presented in this paper. The basic concept is to transmit signs of modulated optical orthogonal frequency division multiplexing (O-OFDM) symbols and absolute values of the symbols separately by two information carrying units: 1) indices of two light emitting diodes (LED) transmitters that represent positive and negative signs separately; and 2) optical intensity symbols that carry the absolute values of signals. The new approach, referred as to non-DC-biased OFDM (NDC-OFDM), uses the optical spatial modulation (OSM) technique to eliminate the effect of the clipping distortion in DC-biased optical OFDM (DCO-OFDM). In addition, it can achieve similar advantages as the conventional unipolar modulation scheme, asymmetrically clipped optical OFDM (ACO-OFDM), without using additional subcarriers. In this paper, the analytical BER performance is compared with the Monte Carlo result in order to prove the reliability of the new method. Moreover, the practical BER performance of NDC-OFDM with DCO-OFDM and ACO-OFDM is compared for different constellation sizes to verify the improvement of NDC-OFDM on the spectral and power efficiencies.

cs.IT↗

arXiv2019

Physical Layer Performance Evaluation of Wireless Infrared-based LiFi Uplink

LiFi (light-fidelity) is recognised as a promising technology for the next generation wireless access network. However, little research effort has been spent on the uplink transmission system in LiFi networks. In this paper, an analytical framework for the performance analysis of an wireless infrared-based LiFi uplink at system level is presented. This work focuses on the performance of a single user who is randomly located in a network. Many important factors in practice are taken into account, such as front-end characteristics, channel path loss, link blockage and user device random orientations. In particular, accurate analytical expressions for the statistics of optical channel path loss has been derived. Based on this path loss statistics, the distribution of signal-to-noise ratio (SNR) and the average achievable data rate are evaluated. A channel factor is defined as a quantity which only depends on the used devices, optical channel and noise power spectral density function (PSD). The result shows that with commercial front-end elements, an average data rate of up to 250 Mbps is achievable.

cs.IT↗

arXiv2019

Impact of Device Orientation on Error Performance of LiFi Systems

Most studies on optical wireless communications (OWCs) have neglected the effect of random orientation in their performance analysis due to the lack of a proper model for the random orientation. Our recent empirical-based research illustrates that the random orientation follows a Laplace distribution for a static user equipment (UE). In this paper, we analyze the device orientation and assess its importance on system performance. The reliability of an OWC channel highly depends on the availability and alignment of line-of-sight (LOS) links. In this study, the effect of receiver orientation including both polar and azimuth angles on the LOS channel gain are analyzed. The probability of establishing a LOS link is investigated and the probability density function (PDF) of signal-to-noise ratio (SNR) for a randomly-oriented device is derived. By means of the PDF of SNR, the bit-error ratio (BER) of DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) in additive white Gaussian noise (AWGN) channels is evaluated. A closed-form approximation for the BER of UE with random orientation is presented which shows a good match with Monte-Carlo simulation results. Furthermore, the impact of the UE's random motion on the BER performance has been assessed. Finally, the effect of random orientation on the average signal-to-interference-plus-noise ratio (SINR) in a multiple access points (APs) scenario is investigated.

cs.IT↗

arXiv2018

Bidirectional Optical Spatial Modulation for Mobile Users: Towards a Practical Design for LiFi Systems

Among the challenges of realizing the full potential of light-fidelity (LiFi) cellular networks are user mobility, random device orientation and blockage. We study the impact of those challenges on the performance of LiFi in an indoor environment using measurement-based channel models. We adopt spatial modulation (SM), which has been shown to be energy efficient in many applications, including LiFi. We consider two configurations for placing the photodiodes (PDs) on the user equipment (UE). The first one is referred to as the screen receiver (SR) whereby all the PDs are located on one face of the UE, whereas the other one is a multi-directional receiver (MDR), in which the PDs are located on different sides of the UE. The latter configuration was motivated by the fact that SR exhibited poor performance in the presence of random device orientation and blockage. We show that MDR outperforms SR by over $10$ dB at BER of $3.8\times10^{-3}$. Moreover, an adaptive access point (AP) selection scheme for SM is considered where the number of APs are chosen adaptively in an effort to achieve the lowest energy requirement for a target BER and spectral efficiency. The user performance with random orientation and blockage in the whole room is evaluated for sitting and walking activities. For the latter, we invoke the orientation-based random waypoint (ORWP) mobility model. We also study the performance of the underlying system on the uplink channel where the same techniques are used for the downlink channel. Specifically, as the transmitted uplink power is constrained, the energy efficiency of SM is evaluated analytically. It is shown that the multi-directional transmitter (MDT) with adaptive SM is highly energy efficient. As a benchmark, we compare the performance of the proposed framework to that of the conventional spatial multiplexing system, and demonstrate the superiority of the proposed one.

eess.SP↗

arXiv2018

Modeling the Random Orientation of Mobile Devices: Measurement, Analysis and LiFi Use Case

Light-fidelity (LiFi) is a networked optical wireless communication (OWC) solution for high-speed indoor connectivity for fixed and mobile optical communications. Unlike conventional radio frequency wireless systems, the OWC channel is not isotropic, meaning that the device orientation affects the channel gain significantly, particularly for mobile users. However, due to the lack of a proper model for device orientation, many studies have assumed that the receiver is vertically upward and fixed. In this paper, a novel model for device orientation based on experimental measurements of forty participants has been proposed. It is shown that the probability density function (PDF) of the polar angle can be modeled either based on a Laplace (for static users) or a Gaussian (for mobile users) distribution. In addition, a closed-form expression is obtained for the PDF of the cosine of the incidence angle based on which line-of-sight (LOS) channel gain is described in OWC channels. An approximation of this PDF based on the truncated Laplace is proposed and the accuracy of this approximation is confirmed by the Kolmogorov-Smirnov distance (KSD). Moreover, the statistics of the LOS channel gain are calculated and the random orientation of a user equipment (UE) is modeled as a random process. The influence of the random orientation on signal-to-noise-ratio (SNR) performance of OWC systems has been evaluated. Finally, an orientation-based random waypoint (ORWP) mobility model is proposed by considering the random orientation of the UE during the user's movement. The performance of ORWP is assessed on the handover rate and it is shown that it is important to take the random orientation into account.

cs.IT↗

arXiv2018

Terminal Orientation in OFDM-based LiFi Systems

Light-fidelity (LiFi) is a wireless communication technology that employs both infrared and visible light spectra to support multiuser access and user mobility. Considering the small wavelength of light, the optical channel is affected by the random orientation of a user equipment (UE). In this paper, a random process model for changes in the UE orientation is proposed based on data measurements. We show that the coherence time of the random orientation is in the order of hundreds of milliseconds. Therefore, an indoor optical wireless channel can be treated as a slowly-varying channel as its delay spread is typically in the order of nanoseconds. A study of the orientation model on the performance of direct-current-biased orthogonal frequency-division multiplexing (DC-OFDM) is also presented. The performance analysis of the DC-OFDM system incorporates the effect of diffuse link due to reflection and blockage by the user. The results show that the diffuse link and the blockage have significant effects, especially if the UE is located relatively far away from an access point (AP). It is shown that the effect is notable if the horizontal distance between the UE and the AP is greater than $1.5$ m in a typical $5\times3.5\times3$ m$^3$ indoor room.

eess.SP↗

arXiv2018

Resource Allocation and Interference Management in OFDMA-based VLC Networks

Resource allocation and interference management are two main issues that need to be carefully addressed in visible light communication (VLC) systems. In this paper, we propose a resource allocation scheme that can also handle the inter-cell interference in a multi-user VLC system that employs orthogonal frequency division multiple access (OFDMA). Particularly, we suggest dividing the cell coverage into two non-overlapping zones and performing a two-step resource allocation process, in which each step corresponds to a different level of allocating resources, i.e., zone and user levels. We initially define both zones in terms of the physical area and the amount of allocated resources and we investigate the impact of illumination requirements on defining both zones. Through simulations, we evaluate the performance of the proposed scheme in terms of the area spectral efficiency and the fairness level between the two zones. We show that both performance measures can be potentially enhanced by carefully setting a certain design parameter that reflects the priority level of the users located in the region around the cell center, denoted as Zone 0, in terms of the achievable rate. We further eventuate the system performance in a realistic transmission scenario using a simulation tool.

cs.IT↗

arXiv2018

Hybrid RF/VLC Systems under QoS Constraints

The coexistence of radio frequency (RF) and visible light communications (VLC) in typical indoor environments can be leveraged to support vast user quality-of-service (QoS) needs. In this paper, we target a hybrid RF/VLC network in which data transmission is provided via either an RF access point or a VLC luminary based on a selection process. We employ the concept of effective capacity, which defines the maximum constant arrival data rate at the transmitter buffer when the QoS needs are imposed as limits on the buffer overflow and delay violation probabilities, as the main selection criteria. We initially formulate the effective capacity of both channels with respect to channel gains and user distribution. Under the assumption of uniform user distribution within the VLC cell, we then provide a closed-form approximation for the effective capacity of the VLC channel. We further investigate the effects of illumination needs and line-of-sight blockage on the VLC performance. In addition, we explore the non-asymptotic bounds regarding the buffering delay by capitalizing on the effective capacity. Through simulation results, we show the impacts of different physical aspects and data-link QoS needs on the effective capacity and delay bounds.

cs.IT↗