arXiv subjects

Hong Ren

Publications and source records attributed to Hong Ren.

At least 55 records · Page 3Linked to original sources

arXiv2025

Channel Estimation for RIS-Aided MU-MIMO mmWave Systems with Practical Hybrid Architecture

This paper proposes a correlation-based three-stage channel estimation strategy with low pilot overhead for reconfigurable intelligent surface (RIS)-aided millimeter wave (mmWave) multi-user (MU) MIMO systems, in which both users and base station (BS) are equipped with a hybrid RF architecture. In Stage I, all users jointly transmit pilots and recover the uncompressed received signals to estimate the angle of arrival (AoA) at the BS using the discrete Fourier transform (DFT). Based on the observation that the overall cascaded MIMO channel can be decomposed into multiple sub-channels, the cascaded channel for a typical user is estimated in Stage II. Specifically, using the invariance of angles and the linear correlation of gains related to different cascaded subchannels, we use compressive sensing (CS), least squares (LS), and a one-dimensional search to estimate the Angles of Departure (AoDs), based on which the overall cascaded channel is obtained. In Stage III, the remaining users independently transmit pilots to estimate their individual cascaded channel with the same approach as in Stage II, which exploits the equivalent common RIS-BS channel obtained in Stage II to reduce the pilot overhead. In addition, the hybrid combining matrix and the RIS phase shift matrix are designed to reduce the noise power, thereby further improving the estimation performance. Simulation results demonstrate that the proposed algorithm can achieve high estimation accuracy especially when the number of antennas at the users is small, and reduce pilot overhead by more than five times compared with the existing benchmark approach.

eess.SP↗

arXiv2025

Novel Synchronization Scheme for Cooperative ISAC Systems

Carrier frequency and timing synchronization play the fundamental roles in cooperative integrating communication and sensing (ISAC). To mitigate the effects of synchronization error, this paper develops a novel synchronization scheme in cell-free massive multiple-input multiple-output (mMIMO) systems. First, we characterize the impacts of pilot contamination on synchronization performance, i.e., Cramer-Rao bound (CRB). Furthermore, a maximum likelihood algorithm is presented to estimate the CFO and TO among the pairing APs. Then, to minimize the sum of CRBs, we devise a synchronization strategy based on a pilot-sharing scheme by jointly optimizing the cluster classification, synchronization overhead, and pilot-sharing scheme, while simultaneously considering the overhead and each AP's synchronization requirements. To solve this NP-hard problem, we simplify it into two sub-problems, namely cluster classification problem and the pilot sharing problem. To strike a balance between synchronization performance and overhead, we first classify the clusters by using the K-means algorithm, and propose a criteria to find a good set of master APs. Then, the pilot-sharing scheme is obtained by using the swap-matching operations. Simulation results validate the accuracy of our derivations and demonstrate the effectiveness of the proposed scheme over the benchmark schemes.

eess.SP↗

arXiv2025

Low-Complexity Iterative Precoding Design for Near-field Multiuser Systems With Spatial Non-Stationarity

Extremely large antenna arrays (ELAA) are regarded as a promising technology for supporting sixth-generation (6G) networks. However, the large number of antennas significantly increases the computational complexity in precoding design, even for linearly regularized zero-forcing (RZF) precoding. To address this issue, a series of low-complexity iterative precoding are investigated. The main idea of these methods is to avoid matrix inversion of RZF precoding. Specifically, RZF precoding is equivalent to a system of linear equations that can be solved by fast iterative algorithms, such as random Kaczmarz (RK) algorithm. Yet, the performance of RK-based precoding algorithm is limited by the energy distributions of multiple users, which restricts its application in ELAA-assisted systems. To accelerate the RK-based precoding, we introduce the greedy random Kaczmarz (GRK)-based precoding by using the greedy criterion-based selection strategy. To further reduce the complexity of the GRK-based precoding, we propose a visibility region (VR)-based orthogonal GRK (VR-OGRK) precoding that leverages near-field spatial non-stationarity, which is characterized by the concept of VR. Next, by utilizing the information from multiple hyperplanes in each iteration, we extend the GRK-based precoding to the aggregation hyperplane Kaczmarz (AHK)-based pecoding algorithm, which further enhances the convergence rate. Building upon the AHK algorithm, we propose a VR-based orthogonal AHK (VR-OAHK) precoding to further reduce the computational complexity. Furthermore, the proposed iterative precoding algorithms are proven to converge to RZF globally at an exponential rate. Simulation results show that the proposed algorithms achieve faster convergence and lower computational complexity than benchmark algorithms, and yield very similar performance to the RZF precoding.

eess.SP↗

arXiv2025

Effective DoF-Oriented Optimal Antenna Spacing in Near-Field XL-MIMO Systems

This letter investigates the optimal antenna spacing for a near-field XL-MIMO communication system from the perspective of the array gain. Specifically, using the Green's function-based channel model, the letter analyzes the channel capacity, which is related to the effective degrees-of-freedom (EDoF). Then, the letter further investigates the applicability of two EDoF estimation methods. To increase EDoF, this letter focuses on analyzing the impact of antenna spacing. Furthermore, from the perspective of the array gain, the letter derives an approximate closed-form expression of the optimal antenna spacing, at which EDoF is maximized and the array gain at the antenna nearest to the focused antenna of the transmit array becomes zero. Finally, numerical results verify the main results of this letter.

eess.SP↗

arXiv2025

RIS-Aided Integrated Sensing and Communication Systems under Dual-polarized Channels

This paper considers reconfigurable intelligent surface (RIS)-aided integrated sensing and communication (ISAC) systems under dual-polarized (DP) channels. Unlike the existing ISAC systems, which ignored polarization of electromagnetic waves, this study adopts DP base station (BS) and DP RIS to serve users with a pair of DP antennas. The achievable sum rate is maximized through jointly optimizing the beamforming matrix at the DP BS, and the reflecting coefficients at the DP RIS. To address this problem, we first utilize the weighted minimum mean-square error (WMMSE) method to transform the objective function into a more tractable form, and then an alternating optimization (AO) method is employed to decouple the original problem into two subproblems. Due to the constant modulus constraint, the DP RIS reflection matrix optimization problem is addressed by the majorization-minimization (MM) method. For the DP beamforming matrix, we propose a penalty-based algorithm that can obtain a low-complexity closed-form solution. Simulation results validate the advantage of deploying DP transmit array and DP RIS in the considered ISAC systems.

cs.IT↗

arXiv2024

Two-Timescale Design for AP Mode Selection of Cooperative ISAC Networks

As an emerging technology, cooperative bi-static integrated sensing and communication (ISAC) is promising to achieve high-precision sensing, high-rate communication as well as self-interference (SI) avoidance. This paper investigates the two-timescale design for access point (AP) mode selection to realize the full potential of the cooperative bi-static ISAC network with low system overhead, where the beamforming at the APs is adapted to the rapidly-changing instantaneous channel state information (CSI), while the AP mode is adapted to the slowly-changing statistical CSI. We first apply the minimum mean square error (MMSE) estimator to estimate the channel between the APs and the channels from the APs to the user equipments (UEs). Then we adopt the low-complexity maximum ratio transmission (MRT) beamforming and the maximum ratio combining (MRC) detector, and derive the closed-form expressions of the communication rate and the sensing signal-to-interference-plus-noise-ratio (SINR). We formulate a non-convex integer optimization problem to maximize the minimum sensing SINR under the communication quality of service (QoS) constraints. McCormick envelope relaxation and successive convex approximation (SCA) techniques are applied to solve the challenging non-convex integer optimization problem. Simulation results validate the closed-form expressions and prove the convergence and effectiveness of the proposed AP mode selection scheme.

eess.SP↗

arXiv2024

Cooperative ISAC-empowered Low-Altitude Economy

This paper proposes a cooperative integrated sensing and communication (ISAC) scheme for the low-altitude sensing scenario, aiming at estimating the parameters of the unmanned aerial vehicles (UAVs) and enhancing the sensing performance via cooperation. The proposed scheme consists of two stages. In Stage I, we formulate the monostatic parameter estimation problem via using a tensor decomposition model. By leveraging the Vandermonde structure of the factor matrix, a spatial smoothing tensor decomposition scheme is introduced to estimate the UAVs' parameters. To further reduce the computational complexity, we design a reduced-dimensional (RD) angle of arrival (AoA) estimation algorithm based on generalized Rayleigh quotient (GRQ). In Stage II, the positions and true velocities of the UAVs are determined through the data fusion across multiple base stations (BSs). Specifically, we first develop a false removing minimum spanning tree (MST)-based data association method to accurately match the BSs' parameter estimations to the same UAV. Then, a Pareto optimality method and a residual weighting scheme are developed to facilitate the position and velocity estimation, respectively. We further extend our approach to the dual-polarized system. Simulation results validate the effectiveness of the proposed schemes in comparison to the conventional techniques.

eess.SP↗

arXiv2024

Sensing Capacity for Integrated Sensing and Communication Systems in Low-Altitude Economy

The burgeoning significance of the low-altitude economy (LAE) has garnered considerable interest, largely fuelled by the widespread deployment of unmanned aerial vehicles (UAVs). To tackle the challenges associated with the detection of unauthorized UAVs and the efficient scheduling of authorized UAVs, this letter introduces a novel performance metric, termed sensing capacity, for integrated sensing and communication (ISAC) systems. This metric, which quantifies the capability of a base station (BS) to detect multiple UAVs simultaneously, leverages signal-to-noise ratio (SNR) and probability of detection (PD) as key intermediate variables. Through mathematical derivations, we can derive a closed-form solution for the maximum number of UAVs that can be detected by the BS while adhering to a specific SNR constraint. Furthermore, an approximate solution based on PD constraints is proposed to facilitate the efficient determination of the threshold for the maximum number of detectable UAVs. The accuracy of this analytical approach is verified through extensive simulation results.

eess.SP↗

arXiv2024

Movable Antenna-enabled RIS-aided Integrated Sensing and Communication

In this paper, we investigate a movable antenna (MA)-aided integrated sensing and communication (ISAC) system, where a reconfigurable intelligent surface (RIS) is employed to enhance wireless communication and sensing performance in dead zones. Specifically, this paper aims to maximize the minimum beampattern gain at the RIS by jointly optimizing beamforming matrix at the base station (BS), the reflecting coefficients at the RIS and the positions of the MAs, subject to signal-to-interference-plus-noise ratio (SINR) constraint for the users and maximum transmit power at the BS. To tackle this non-convex optimization problem, we propose an alternating optimization (AO) algorithm and employ semidefinite relaxation (SDR), sequential rank-one constraint relaxation (SRCR) and successive convex approximation (SCA) techniques. Numerical results indicate that the MA and RIS-aided ISAC system outperforms conventional fixed position antenna (FPA) and RIS-aided systems. In addition, the application of MAs can reduce the similarity of user channels and enhance channel gain in the ISAC system.

eess.SP↗

arXiv2024

A Framework of RIS-assisted ICSC User-centric Based Systems: Latency Optimization and Design

This paper studies a comprehensive framework for reconfigurable intelligent surface (RIS)-assisted integrated communication, sensing, and computation (ICSC) systems with a User-centric focus. The study encompasses two scenarios: the general multi-user equipment (UE) scenario and the simplified single-UE scenario. To satisfy the critical need for time-efficient sensing, we investigate the latency minimization problem, subject to constraints on UEs' transmit power, radar signal-to-interference-plus-noise-ratio (SINR), RIS phase shift, and computation capability. To address the formulated non-convex problem in the multi-UE scenario, we decouple the original problem into two subproblems, where the computational and beamforming settings are optimized alternately. Specifically, for the computational settings, we derive a closed-form solution for the offloading volume and propose a low-complexity algorithm based on the bisection search method to optimize the edge computing resource allocation. Additionally, we employ two equivalent transformations to address the challenge posed by the non-convex sum-of-ratios form in the objective function (OF) of the subproblem related to active and passive beamforming. Several techniques are then combined to address these subproblems. Furthermore, a low-complexity algorithm that offers closed-form solutions is developed for the simplified single UE scenario. Finally, simulation results substantiate the effectiveness of the proposed framework.

eess.SP↗

arXiv2024

Addressing the Mutual Interference in Uplink ISAC Receivers: A Projection Method

Dual function radar and communication (DFRC) is a promising research direction within integrated sensing and communication (ISAC), improving hardware and spectrum efficiency by merging sensing and communication (S&C) functionalities into a shared platform. However, the DFRC receiver (DFRC-R) is tasked with both uplink communication signal detection and simultaneously target-related parameter estimation from the echoes, leading to issues with mutual interference. In this paper, a projection-based scheme is proposed to equivalently transform the joint signal detection and target estimation problem into a joint signal detection process across multiple snapshots. Compared with conventional successive interference cancellation (SIC) schemes, our proposed approach achieves a higher signal-to-noise ratio (SNR), and a higher ergodic rate when the radar signal is non-negligible. Nonetheless, it introduces an ill-conditioned signal detection problem, which is addressed using a non-linear detector. By jointly processing an increased number of snapshots, the proposed scheme can achieve high S&C performance simultaneously.

cs.IT↗

arXiv2024

Channel Estimation for mmWave MIMO-OFDM Systems in High-Mobility Scenarios: Instantaneous Model or Statistical Model?

Classical linear statistical models, like the first-order auto-regressive (AR) model, are commonly used as channel model in high-mobility scenarios. However, compared to sub-6G, the effect of Doppler frequency shifts is more significant at millimeter wave (mmWave) frequencies, and the effectiveness of the statistical channel model in high-mobility mmWave scenarios should be reconsidered. In this paper, we investigate the channel estimation for mmWave multiple-input multiple-output-(MIMO) orthogonal frequency division multiplexing (OFDM) systems in high-mobility scenarios, with the focus on the comparison between the instantaneous channel model and the statistical channel model. For the instantaneous model, by leveraging the low-rank nature of mmWave channels and the multidimensional characteristics of MIMO-OFDM signals across space, time, and frequency, the received signals are structured as a fourth-order tensor fitting a low-rank CANDECOMP/PARAFAC (CP) model. Then, to solve the CP decomposition problem, an estimation of signal parameters via rotational invariance techniques (ESPRIT)-type decomposition based channel estimation method is proposed by exploring the Vandermonde structure of factor matrix, and the channel parameters are then estimated from the factor matrices. We analyze the uniqueness condition of the CP decomposition and develop a concise derivation of the Cramer-Rao bound (CRB) for channel parameters. Simulations show that our method outperforms the existing benchmarks. Furthermore, the results based on the wireless environment generated by Wireless InSite verify that the channel estimation based on the instantaneous channel model performs better than that based on the statistical channel model. Therefore, the instantaneous channel model is recommended for designing channel estimation algorithm for mmWave systems in high-mobility scenarios.

cs.IT↗

arXiv2024

Beamforming Design for Double-Active-RIS-aided Communication Systems with Inter-Excitation

In this paper, we investigate a double-active-reconfigurable intelligent surface (RIS)-aided downlink wireless communication system, where a multi-antenna base station (BS) serves multiple single-antenna users with both double reflection and single reflection links. Due to the signal amplification capability of active RISs, they can effectively mitigate the multiplicative fading effect. However, this also induces signal bouncing between the two active RISs that cannot be ignored. This phenomenon is termed as the "inter-excitation" effect and is characterized in the received signal by proposing a feedback-type model. Based on the signal model, we formulate a weighted sum rate (WSR) maximization problem by jointly optimizing the beamforming matrix at the BS and the reflecting coefficient matrices at the two active RISs, subject to power constraints at the BS and active RISs, as well as the maximum amplification gain constraints of the active RISs. To solve this non-convex problem, we first transform the problem into a more tractable form using the fractional programming (FP) method. Then, by introducing auxiliary variables, the problem can be converted into an equivalent form that can be solved by using a penalty dual decomposition (PDD) algorithm. Finally, simulation results indicate that it proposed scheme outperforms benchmark schemes with single active RIS and double passive RISs in terms of achievable rate. Furthermore, the results demonstrate that the proposed scheme can enhance the WSR by 30\% compared to scenarios that do not take this effect into account when the maximum amplification gain is 40 dB. Additionally, the proposed scheme is capable of achieving high WSR performance at most locations where double active RISs are deployed between the BS and the users, thereby providing greater flexibility in their positioning.

eess.SP↗

arXiv2024

Target Localization in Cooperative ISAC Systems: A Scheme Based on 5G NR OFDM Signals

The integration of sensing capabilities into communication systems, by sharing physical resources, has a significant potential for reducing spectrum, hardware, and energy costs while inspiring innovative applications. Cooperative networks, in particular, are expected to enhance sensing services by enlarging the coverage area and enriching sensing measurements, thus improving the service availability and accuracy. This paper proposes a cooperative integrated sensing and communication (ISAC) framework by leveraging information-bearing orthogonal frequency division multiplexing (OFDM) signals transmitted by access points (APs). Specifically, we propose a two-stage scheme for target localization, where communication signals are reused as sensing reference signals based on the system information shared at the central processing unit (CPU). In Stage I, we propose a twodimensional fast Fourier transform (2D-FFT)-based algorithm to measure the ranges of scattered paths induced by targets, through the extraction of delay and Doppler information from the sensing channels between APs. Then, the target locations are estimated in Stage II based on these range measurements. Considering the potential occurrence of ill-conditioned measurements with large error during the extraction of time-frequency information, we propose an efficient algorithm to match the range measurements with the targets while eliminating ill-onditioned measurements, achieving high-accuracy target localization. In addition, based on the transmission configurations defined in the fifth generation (5G) standards, we elucidate the performance trade-offs in both communication and sensing, and extend the proposed sensing scheme for general scenarios. Finally, numerical results confirm the effectiveness of our sensing scheme and the cooperative gain of the ISAC framework.

eess.SP↗

arXiv2024

Near-Field Mobile Tracking: A Framework of Using XL-RIS Information

This paper introduces a novel mobile tracking framework leveraging the high-dimensional signal received from extremely large-scale (XL) reconfigurable intelligent surfaces (RIS). This received signal, named XL-RIS information, has a much larger data dimension and therefore offers a richer feature set compared to the traditional base station (BS) received signal, i.e., BS information, enabling more accurate tracking of mobile users (MUs). As the first step, we present an XL-RIS information reconstruction (XL-RIS-IR) algorithm to reconstruct the high-dimensional XL-RIS information from the low-dimensional BS information. Building on this, this paper proposes a comprehensive framework for mobile tracking, consisting of a Feature Extraction Module and a Mobile Tracking Module. The Feature Extraction Module incorporates a convolutional neural network (CNN) extractor for spatial features, a time and frequency (T$\&$F) extractor for domain features, and a near-field angles of arrival (AoAs) extractor for capturing AoA features within the XL-RIS. These features are combined into a comprehensive feature vector, forming a time-varying sequence fed into the Mobile Tracking Module, which employs an Auto-encoder (AE) with a stacked bidirectional long short-term memory (Bi-LSTM) encoder and a standard LSTM decoder to predict MUs' positions in the upcoming time slot. Simulation results confirm that the tracking accuracy of our proposed framework is significantly enhanced by using reconstructed XL-RIS information and exhibits substantial robustness to signal-to-noise ratio (SNR) variations.

eess.SP↗

arXiv2024

Exploit High-Dimensional RIS Information to Localization: What Is the Impact of Faulty Element?

This paper proposes a novel localization algorithm using the reconfigurable intelligent surface (RIS) received signal, i.e., RIS information. Compared with BS received signal, i.e., BS information, RIS information offers higher dimension and richer feature set, thereby providing an enhanced capacity to distinguish positions of the mobile users (MUs). Additionally, we address a practical scenario where RIS contains some unknown (number and places) faulty elements that cannot receive signals. Initially, we employ transfer learning to design a two-phase transfer learning (TPTL) algorithm, designed for accurate detection of faulty elements. Then our objective is to regain the information lost from the faulty elements and reconstruct the complete high-dimensional RIS information for localization. To this end, we propose a transfer-enhanced dual-stage (TEDS) algorithm. In \emph{Stage I}, we integrate the CNN and variational autoencoder (VAE) to obtain the RIS information, which in \emph{Stage II}, is input to the transferred DenseNet 121 to estimate the location of the MU. To gain more insight, we propose an alternative algorithm named transfer-enhanced direct fingerprint (TEDF) algorithm which only requires the BS information. The comparison between TEDS and TEDF reveals the effectiveness of faulty element detection and the benefits of utilizing the high-dimensional RIS information for localization. Besides, our empirical results demonstrate that the performance of the localization algorithm is dominated by the high-dimensional RIS information and is robust to unoptimized phase shifts and signal-to-noise ratio (SNR).

eess.SP↗

arXiv2024

Employing High-Dimensional RIS Information for RIS-aided Localization Systems

Reconfigurable intelligent surface (RIS)-aided localization systems have attracted extensive research attention due to their accuracy enhancement capabilities. However, most studies primarily utilized the base stations (BS) received signal, i.e., BS information, for localization algorithm design, neglecting the potential of RIS received signal, i.e., RIS information. Compared with BS information, RIS information offers higher dimension and richer feature set, thereby significantly improving the ability to extract positions of the mobile users (MUs). Addressing this oversight, this paper explores the algorithm design based on the high-dimensional RIS information. Specifically, we first propose a RIS information reconstruction (RIS-IR) algorithm to reconstruct the high-dimensional RIS information from the low-dimensional BS information. The proposed RIS-IR algorithm comprises a data processing module for preprocessing BS information, a convolution neural network (CNN) module for feature extraction, and an output module for outputting the reconstructed RIS information. Then, we propose a transfer learning based fingerprint (TFBF) algorithm that employs the reconstructed high-dimensional RIS information for MU localization. This involves adapting a pre-trained DenseNet-121 model to map the reconstructed RIS signal to the MU's three-dimensional (3D) position. Empirical results affirm that the localization performance is significantly influenced by the high-dimensional RIS information and maintains robustness against unoptimized phase shifts.

eess.SP↗

arXiv2024

Two-Timescale Design for Reconfigurable Intelligent Surface-Aided URLLC

In this paper, to tackle the blockage issue in massive multiple-input-multiple-output (mMIMO) systems, a reconfigurable intelligent surface (RIS) is seamlessly deployed to support devices with ultra-reliable and low-latency communications (URLLC). The transmission power of the base station and the phase shifts of the RIS are jointly devised to maximize the weighted sum rate while considering the spatially correlation and channel estimation errors. Firstly, \textcolor{black}{the relationship between the channel estimation error and spatially correlated RIS's elements is revealed by using the linear minimum mean square error}. Secondly, based on the maximum-ratio transmission precoding, a tight lower bound of the rate under short packet transmission is derived. Finally, the NP-hard problem is decomposed into two optimization problems, where the transmission power is obtained by geometric programming and phase shifts are designed by using gradient ascent method. Besides, we have rigorously proved that the proposed algorithm can rapidly converge to a sub-optimal solution with low complexity. Simulation results confirm the tightness between the analytic results and Monte Carlo simulations. Furthermore, the two-timescale scheme provides a practical solution for the short packet transmission.

eess.SP↗