arXiv subjects

Hyeongtaek Lee

Publications and source records attributed to Hyeongtaek Lee.

14 recordsLinked to original sources

arXiv2026

Beam Training for RIS-Aided ISAC Systems

As a key technology for 6G, integrated sensing and communication (ISAC) is receiving considerable attention, and deploying a reconfigurable intelligent surface (RIS) can enhance both communication performance and sensing capability of ISAC by providing additional degrees of freedom. In this paper, we investigate a beam training framework for RIS-aided ISAC systems where beam alignment for a communication user equipment (UE) is conducted while simultaneously detecting a single target through its echo signal. Using codebooks constructed according to the principles of the 5G standard, we propose a partial search procedure that achieves low training overhead and mathematically show that this strategy is sufficient to identify a suitable codeword combination to serve the UE. By applying the auxiliary beam pair method, the target's angle information from the perspectives of the base station and RIS is obtained. Then, a high-accuracy closed-form localization is proposed based on the angle estimates, and we further extend the proposed technique to multi-target localization scenarios. Numerical results highlight the advantages of the proposed technique in the ISAC context, showing that the training procedure can effectively find a codeword combination and that the target localization technique outperforms the benchmarks.

cs.IT↗

arXiv2025

Downlink Channel Estimation for mmWave Systems with Impulsive Interference

In this paper, we investigate a channel estimation problem in a downlink millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system, which suffers from impulsive interference caused by hardware non-idealities or external disruptions. Specifically, impulsive interference presents a significant challenge to channel estimation due to its sporadic, unpredictable, and high-power nature. To tackle this issue, we develop a Bayesian channel estimation technique based on variational inference (VI) that leverages the sparsity of the mmWave channel in the angular domain and the intermittent nature of impulsive interference to minimize channel estimation errors. The proposed technique employs mean-field approximation to approximate posterior inference and integrates VI into the sparse Bayesian learning (SBL) framework. Simulation results demonstrate that the proposed technique outperforms baselines in terms of channel estimation accuracy.

cs.IT↗

arXiv2025

Task-Based Quantization for Channel Estimation in RIS Empowered MmWave Systems

In this paper, we investigate channel estimation for reconfigurable intelligent surface (RIS) empowered millimeter-wave (mmWave) multi-user single-input multiple-output communication systems using low-resolution quantization. Due to the high cost and power consumption of analog-to-digital converters (ADCs) in large antenna arrays and for wide signal bandwidths, designing mmWave systems with low-resolution ADCs is beneficial. To tackle this issue, we propose a channel estimation design using task-based quantization that considers the underlying hybrid analog and digital architecture in order to improve the system performance under finite bit-resolution constraints. Our goal is to accomplish a channel estimation task that minimizes the mean squared error distortion between the true and estimated channel. We develop two types of channel estimators: a cascaded channel estimator for an RIS with purely passive elements, and an estimator for the separate RIS-related channels that leverages additional information from a few semi-passive elements at the RIS capable of processing the received signals with radio frequency chains. Numerical results demonstrate that the proposed channel estimation designs exploiting task-based quantization outperform purely digital methods and can effectively approach the performance of a system with unlimited resolution ADCs. Furthermore, the proposed channel estimators are shown to be superior to baselines with small training overhead.

cs.IT↗

arXiv2025

Robust Transmission Design for Active RIS-Aided Systems

Different from conventional passive reconfigurable intelligent surfaces (RISs), incident signals and thermal noise can be amplified at active RISs. By exploiting the amplifying capability of active RISs, noticeable performance improvement can be expected when precise channel state information (CSI) is available. Since obtaining perfect CSI related to an RIS is difficult in practice, a robust transmission design is proposed in this paper to tackle the channel uncertainty issue, which will be more severe for active RIS-aided systems. To account for the worst-case scenario, the minimum achievable rate of each user is derived under a statistical CSI error model. Subsequently, an optimization problem is formulated to maximize the sum of the minimum achievable rate. Since the objective function is non-concave, the formulated problem is transformed into a tractable lower bound maximization problem, which is solved using an alternating optimization method. Numerical results show that the proposed robust design outperforms a baseline scheme that only exploits estimated CSI.

cs.IT↗

arXiv2024

An Experimental Multi-Band Channel Characterization in the Upper Mid-Band

The following paper provides a multi-band channel measurement analysis on the frequency range (FR)3. This study focuses on the FR3 low frequencies 6.5 GHz and 8.75 GHz with a setup tailored to the context of integrated sensing and communication (ISAC), where the data are collected with and without the presence of a target. A method based on multiple signal classification (MUSIC) is used to refine the delays of the channel impulse response estimates. The results reveal that the channel at the lower frequency 6.5 GHz has additional distinguishable multipath components in the presence of the target, while the one associated with the higher frequency 8.75 GHz has more blockage. The set of results reported in this paper serves as a benchmark for future multi-band studies in the FR3 spectrum.

cs.IT↗

arXiv2024

RIS-Enabled Cellular Systems Operated by Different Service Providers

In realistic cellular communication systems, multiple service providers will operate within different frequency ranges. Each serving cell, which is managed by a distinct service provider, is designed individually due to the orthogonal frequencies. However, when a reconfigurable intelligent surface (RIS) is deployed for a certain cell, the RIS still incurs reflective channels for the overall system since the RIS reflects signals across all frequency ranges. This may cause severe undesired performance degradation for the other cells unless the reflection coefficients are properly designed. To tackle this issue, by utilizing the Riemannian manifold optimization method, an RIS reflection coefficients design is proposed in this paper to maximize the performance improvements of the cell that deploys the RIS while minimizing the undesired performance degradation for the other cells simultaneously. Numerical results demonstrate that the proposed design can effectively balance the two objectives for practical scenarios.

cs.IT↗

arXiv2024

Multi-Group Multicasting Systems Using Multiple RISs

In this paper, practical utilization of multiple distributed reconfigurable intelligent surfaces (RISs), which are able to conduct group-specific operations, for multi-group multicasting systems is investigated. To tackle the inter-group interference issue in the multi-group multicasting systems, the block diagonalization (BD)-based beamforming is considered first. Without any inter-group interference after the BD operation, the multiple distributed RISs are operated to maximize the minimum rate for each group. Since the computational complexity of the BD-based beamforming can be too high, a multicasting tailored zero-forcing (MTZF) beamforming technique is proposed to efficiently suppress the inter-group interference, and the novel design for the multiple RISs that makes up for the inevitable loss of MTZF beamforming is also described. Effective closed-form solutions for the loss minimizing RIS operations are obtained with basic linear operations, making the proposed MTZF beamforming-based RIS design highly practical. Numerical results show that the BD-based approach has ability to achieve high sum-rate, but it is useful only when the base station deploys large antenna arrays. Even with the small number of antennas, the MTZF beamforming-based approach outperforms the other schemes in terms of the sum-rate while the technique requires low computational complexity. The results also prove that the proposed techniques can work with the minimum rate requirement for each group.

cs.IT↗

arXiv2024

Joint Downlink and Uplink Optimization for RIS-Aided FDD MIMO Communication Systems

This paper investigates reconfigurable intelligent surface (RIS)-aided frequency division duplexing (FDD) communication systems. Since the downlink and uplink signals are simultaneously transmitted in FDD, the phase shifts at the RIS should be designed to support both transmissions. Considering a single-user multiple-input multiple-output system, we formulate a weighted sum-rate maximization problem to jointly maximize the downlink and uplink system performance. To tackle the non-convex optimization problem, we adopt an alternating optimization (AO) algorithm, in which two phase shift optimization techniques are developed to handle the unit-modulus constraints induced by the reflection coefficients at the RIS. The first technique exploits the manifold optimization-based algorithm, while the second uses a lower-complexity AO approach. Numerical results verify that the proposed techniques rapidly converge to local optima and significantly improve the overall system performance compared to existing benchmark schemes.

cs.IT↗

arXiv2023

Channel Estimation for Reconfigurable Intelligent Surface with a few Active Elements

In this paper, a channel estimation technique for reconfigurable intelligent surface (RIS)-aided multi-user multiple-input single-output communication systems is proposed. By deploying a small number of active elements at the RIS, the RIS can receive and process the training signals. Through the partial channel state information (CSI) obtained from the active elements, the overall training overhead to estimate the entire channel can be dramatically reduced. To minimize the estimation complexity, the proposed technique is based on the linear combination of partial CSI, which only requires linear matrix operations. By exploiting the spatial correlation among the RIS elements, proper weights for the linear combination and normalization factors are developed. Numerical results show that the proposed technique outperforms other schemes using the active elements at the RIS in terms of the normalized mean squared error when the number of active elements is small, which is necessary to maintain the low cost and power consumption of RIS.

cs.IT↗

arXiv2021

Practical Channel Estimation and Phase Shift Design for Intelligent Reflecting Surface Empowered MIMO Systems

In this paper, channel estimation techniques and phase shift design for intelligent reflecting surface (IRS)-empowered single-user multiple-input multiple-output (SU-MIMO) systems are proposed. Among four channel estimation techniques developed in the paper, the two novel ones, single-path approximated channel (SPAC) and selective emphasis on rank-one matrices (SEROM), have low training overhead to enable practical IRS-empowered SU-MIMO systems. SPAC is mainly based on parameter estimation by approximating IRS-related channels as dominant single-path channels. SEROM exploits IRS phase shifts as well as training signals for channel estimation and easily adjusts its training overhead. A closed-form solution for IRS phase shift design is also developed to maximize spectral efficiency where the solution only requires basic linear operations. Numerical results show that SPAC and SEROM combined with the proposed IRS phase shift design achieve high spectral efficiency even with low training overhead compared to existing methods.

cs.IT↗

arXiv2021

Complete Power Reallocation for MU-MIMO under Per-Antenna Power Constraint

This paper proposes a beamforming method under a per-antenna power constraint (PAPC). Although many beamformer designs with the PAPC need to solve complex optimization problems, the proposed complete power reallocation (CPR) method can generate beamformers with excellent performance only with linear operations. CPR is designed to have a simple structure, making it highly flexible and practical. In this paper, three CPR variations considering algorithm convergence speed, sum-rate maximization, and robustness to channel uncertainty are developed. Simulation results verify that CPR and its variations satisfy their design criteria, and, hence, CPR can be readily utilized for various purposes.

cs.IT↗

arXiv2021

Downlink Channel Reconstruction for Spatial Multiplexing in Massive MIMO Systems

To get channel state information (CSI) at a base station (BS), most of researches on massive multiple-input multiple-output (MIMO) systems consider time division duplexing (TDD) to get benefit from the uplink and downlink channel reciprocity. Even in TDD, however, the BS still needs to transmit downlink training signals, which are referred to as channel state information reference signals (CSI-RSs) in the 3GPP standard, to support spatial multiplexing in practice. This is because there are many cases that the number of transmit antennas is less than the number of receive antennas at a user equipment (UE) due to power consumption and circuit complexity issues. Because of this mismatch, uplink sounding reference signals (SRSs) from the UE are not enough for the BS to obtain full downlink MIMO CSI. Therefore, after receiving the downlink CSI-RSs, the UE needs to feed back quantized CSI to the BS using a pre-defined codebook to support spatial multiplexing. In this paper, possible approaches to reconstruct full downlink MIMO CSI at the BS are proposed by exploiting both the SRS and quantized downlink CSI considering practical antenna structures with reduced downlink CSI-RS overhead. Numerical results show that the spectral efficiencies by spatial multiplexing based on the proposed downlink MIMO CSI reconstruction techniques outperform the conventional methods solely based on the quantized CSI.

cs.IT↗

arXiv2020

Massive MIMO Channel Prediction: Kalman Filtering vs. Machine Learning

This paper focuses on channel prediction techniques for massive multiple-input multiple-output (MIMO) systems. Previous channel predictors are based on theoretical channel models, which would be deviated from realistic channels. In this paper, we develop and compare a vector Kalman filter (VKF)-based channel predictor and a machine learning (ML)-based channel predictor using the realistic channels from the spatial channel model (SCM), which has been adopted in the 3GPP standard for years. First, we propose a low-complexity mobility estimator based on the spatial average using a large number of antennas in massive MIMO. The mobility estimate can be used to determine the complexity order of developed predictors. The VKF-based channel predictor developed in this paper exploits the autoregressive (AR) parameters estimated from the SCM channels based on the Yule-Walker equations. Then, the ML-based channel predictor using the linear minimum mean square error (LMMSE)-based noise pre-processed data is developed. Numerical results reveal that both channel predictors have substantial gain over the outdated channel in terms of the channel prediction accuracy and data rate. The ML-based predictor has larger overall computational complexity than the VKF-based predictor, but once trained, the operational complexity of ML-based predictor becomes smaller than that of VKF-based predictor.

cs.IT↗

arXiv2019

Efficient Channel AoD/AoA Estimation Using Widebeams for Millimeter Wave MIMO Systems

Using millimeter-wave (mmWave) bands is expected to provide high data rates through large licensed and unlicensed spectrum. Due to large path loss and sparse scattering propagation properties, proper beam alignment is important in mmWave systems. Small carrier wavelengths at mmWave bands let wireless communication systems use large antenna arrays to provide sufficient beamforming gain with highly directional beams. Hence, high resolution channel angle-of-departure (AoD) and angle-of-arrival (AoA) estimation is crucial for beam alignment to get the advantages of large beamforming gain. Using large antenna arrays, however, can lead to high system complexity and channel estimation overhead. This paper proposes a channel AoD/AoA estimation technique using widebeams to lower estimation overhead and auxiliary-beam-pair (ABP) to get high resolution channel AoD/AoA estimates considering hybrid transceiver structures. To fully use the hybrid transceiver structures, the linear combination of discrete Fourier transform (DFT) vectors is considered to construct widebeams. Numerical results show that the proposed estimator can get high resolution channel AoD/AoA estimates with lower overhead compared to previous estimators.

eess.SP↗