arXiv subjects

Ilya Charaev

Publications and source records attributed to Ilya Charaev.

At least 19 recordsLinked to original sources

arXiv2025

Magnetic-field dependent vortex dynamics and critical currents in superconducting microwires with regular large-area perforation by pinholes

We report on results of simulations and experiments of vortex states in superconducting micro-wires with periodic rectangular pinhole structures. The simulations have been performed by means of numerically solving the time-dependent Ginzburg-Landau (TDGL) equations. With increasing bias current and for different values of the external magnetic field applied normal to the structure plane, we observe at first a vortex free Meissner state, followed by a resistive vortex-flow mixed state and a state with a more complex vortex pattern. The resulting dependence of the critical current Ic on magnetic field exhibits two plateaus with distinctly different vortex dynamics. Corresponding experimentally measured magnetic-field dependences of Ic of WSi microwires with periodic pinhole structures and varying hole spacing confirmed the predictions of these simulations, showing two ranges of magnetic field with almost field-independent critical currents. The experimentally determined critical currents are larger for a smaller pinhole spacing, in agreement with the results of the TDGL simulations. The good agreement of the simulations with the experimental results provides a convenient strategy for the optimization of single-photon detectors with or without artificial and natural defects.

cond-mat.supr-con↗

arXiv2025

Bolometric Superconducting Optical Nanoscopy (BOSON)

Superconducting transition-edge sensors are renowned for their extraordinary photon sensitivity and energy resolution, finding applications spanning quantum information, astronomy, and nanophotonics. Here, we report the development of BOlometric Superconducting Optical Nanoscopy (BOSON), a novel platform that integrates bolometric detection at the superconducting transition edges with near-field optical techniques. BOSON enables the mapping of photoinduced changes in superconductivity with unprecedented spatial resolution and photon sensitivity. By incorporating BOSON with low-dimensional materials, we achieved polariton imaging at nanowatt excitation levels--at least four orders of magnitude lower than the power typically required in prior near-field nanoscopy experiments. Our findings highlight the potential for BOSON to advance scanning probe based optical platforms to enable the detection of photons, polaritons, and Cooper pair dynamics at the nanoscale. This paves the way for quantum sensing applications using single-polariton detection and can offer deeper insights into quasiparticle dynamics.

quant-ph↗

arXiv2024

First Sub-MeV Dark Matter Search with the QROCODILE Experiment Using Superconducting Nanowire Single-Photon Detectors

We present the first results from the Quantum Resolution-Optimized Cryogenic Observatory for Dark matter Incident at Low Energy (QROCODILE). The QROCODILE experiment uses a microwire-based superconducting nanowire single-photon detector (SNSPD) as a target and sensor for dark matter scattering and absorption, and is sensitive to energy deposits as low as 0.11 eV. We introduce the experimental configuration and report new world-leading constraints on the interactions of sub-MeV dark matter particles with masses as low as 30 keV. The thin-layer geometry of the system provides anisotropy in the interaction rate, enabling directional sensitivity. In addition, we leverage the coupling between phonons and quasiparticles in the detector to simultaneously constrain interactions with both electrons and nucleons. We discuss the potential for improvements to both the energy threshold and effective volume of the experiment in the coming years.

hep-ph↗

arXiv2023

Effective suppression of dark counts in superconducting microstructures with grid of pinholes in a magnetic field

In a magnetic field, vortices significantly contribute to the dark counts of single-photon detectors made of superconducting wires, and they are also limiting the critical current of such devices. To address this issue, we prepared superconducting microwires with a pinhole grid from WSi thin films and report on corresponding critical-current and count-rate measurements in an external magnetic field B. When compared to corresponding devices without pinholes, the critical current only weakly depends on the magnetic field at B < 16 mT and it is even larger already at B > 10 mT. Moreover, dark counts are not only suppressed in zero field, but particularly in magnetic fields B < 16 mT, while photon counts are virtually field insensitive in the same range of the magnetic field.

cond-mat.supr-con↗

arXiv2023

Large active-area superconducting microwire detector array with single-photon sensitivity in the near-infrared

Superconducting nanowire single photon detectors (SNSPDs) are the highest-performing technology for time-resolved single-photon counting from the UV to the near-infrared. The recent discovery of single-photon sensitivity in micrometer-scale superconducting wires is a promising pathway to explore for large active area devices with application to dark matter searches and fundamental physics experiments. We present 8-pixel $1 mm^2$ superconducting microwire single photon detectors (SMSPDs) with $1\,\mathrm{μm}$-wide wires fabricated from WSi and MoSi films of various stoichiometries using electron-beam and optical lithography. Devices made from all materials and fabrication techniques show saturated internal detection efficiency at 1064 nm in at least one pixel, and the best performing device made from silicon-rich WSi shows single-photon sensitivity in all 8 pixels and saturated internal detection efficiency in 6/8 pixels. This detector is the largest reported active-area SMSPD or SNSPD with near-IR sensitivity published to date, and the first report of an SMSPD array. By further optimizing the photolithography techniques presented in this work, a viable pathway exists to realize larger devices with $cm^2$-scale active area and beyond.

physics.ins-det↗

arXiv2022

New constraints on dark matter from superconducting nanowires

Superconducting nanowires, a mature technology originally developed for quantum sensing, can be used as a target and sensor with which to search for dark matter interactions with electrons. Here we report on a 180-hour measurement of a tungsten silicide superconducting nanowire device with a mass of 4.3 nanograms. We use this to place new constraints on dark matter--electron interactions, including the strongest terrestrial constraints to date on sub-MeV (sub-eV) dark matter that interacts with electrons via scattering (absorption) processes.

hep-ph↗

arXiv2022

New Constraints on Dark Photon Dark Matter with Superconducting Nanowire Detectors in an Optical Haloscope

Uncovering the nature of dark matter is one of the most important goals of particle physics. Light bosonic particles, such as the dark photon, are well-motivated candidates: they are generally long-lived, weakly-interacting, and naturally produced in the early universe. In this work, we report on LAMPOST (Light $A'$ Multilayer Periodic Optical SNSPD Target), a proof-of-concept experiment searching for dark photon dark matter in the eV mass range, via coherent absorption in a multi-layer dielectric haloscope. Using a superconducting nanowire single-photon detector (SNSPD), we achieve efficient photon detection with a dark count rate (DCR) of $\sim 6\times10^{-6}$ counts/s. We find no evidence for dark photon dark matter in the mass range of $\sim 0.7$-$0.8$ eV with kinetic mixing $ε\gtrsim 10^{-12}$, improving existing limits in $ε$ by up to a factor of two. With future improvements to SNSPDs, our architecture could probe significant new parameter space for dark photon and axion dark matter in the meV to 10 eV mass range.

hep-ex↗

arXiv2021

Physical properties of amorphous molybdenum silicide films for single photon detectors

We systematically investigated the physical properties of amorphous Mo$_{\rm x}$Si$_{1-x}$ films deposited by the magnetron co-sputtering technique. The critical temperature $T_C$ of Mo$_{\rm x}$ Si$_{1-x}$ films increases gradually with the stoichiometry x, and the highest $T_C$=7.9 K was found in Mo$_{\rm 0.83}$ Si$_{0.17}$. Beyond $x$=0.83, preformed Cooper pairs and superconducting domains persist in the films, despite the superconducting state with perfect zero-resistivity is absent. The thick films of Mo$_{\rm 0.83}$ Si$_{0.17}$ show surprising degradation in which the onset of zero-resistivity is suppressed below 2 K. The thin Mo$_{\rm 0.83}$ Si$_{0.17}$ films, however, reveal robust superconductivity even with thickness d$\leq$1 nm. We also characterized wide microwires based on the 2 nm thin Mo$_{\rm 0.8}$ Si$_{0.2}$ films with widths 40 and 60 $μ$m, which show single-photon sensitivity at 780 nm and 1550 nm wavelength

cond-mat.supr-con↗

arXiv2021

Self-Heating Hotspots in Superconducting Nanowires Cooled by Phonon Black-Body Radiation

Controlling thermal transport is important for a range of devices and technologies, from phase change memories to next-generation electronics. This is especially true in nano-scale devices where thermal transport is altered by the influence of surfaces and changes in dimensionality. In superconducting nanowire single-photon detectors, the thermal boundary conductance (TBC) between the nanowire and the substrate it is fabricated on influences most of the performance metrics that make these detectors attractive for applications. This includes the maximum count rate, latency, jitter, and quantum efficiency. Despite its importance, the study of TBC in superconducting nanowire devices has not been done systematically, primarily due to the lack of a straightforward characterization method. Here, we show that simple electrical measurements can be used to estimate the TBC between nanowires and substrates and that these measurements match acoustic mismatch theory across a variety of substrates. Numerical simulations allow us to refine our understanding, however, open questions remain. This work should enable thermal engineering in superconducting nanowire electronics and cryogenic detectors for improved device performance.

cond-mat.supr-con↗

arXiv2021

Opportunities for DOE National Laboratory-led QuantISED Experiments

A subset of QuantISED Sensor PIs met virtually on May 26, 2020 to discuss a response to a charge by the DOE Office of High Energy Physics. In this document, we summarize the QuantISED sensor community discussion, including a consideration of HEP science enabled by quantum sensors, describing the distinction between Quantum 1.0 and Quantum 2.0, and discussing synergies/complementarity with the new DOE NQI centers and with research supported by other SC offices. Quantum 2.0 advances in sensor technology offer many opportunities and new approaches for HEP experiments. The DOE HEP QuantISED program could support a portfolio of small experiments based on these advances. QuantISED experiments could use sensor technologies that exemplify Quantum 2.0 breakthroughs. They would strive to achieve new HEP science results, while possibly spinning off other domain science applications or serving as pathfinders for future HEP science targets. QuantISED experiments should be led by a DOE laboratory, to take advantage of laboratory technical resources, infrastructure, and expertise in the safe and efficient construction, operation, and review of experiments. The QuantISED PIs emphasized that the quest for HEP science results under the QuantISED program is distinct from the ongoing DOE HEP programs on the energy, intensity, and cosmic frontiers. There is robust evidence for the existence of particles and phenomena beyond the Standard Model, including dark matter, dark energy, quantum gravity, and new physics responsible for neutrino masses, cosmic inflation, and the cosmic preference for matter over antimatter. Where is this physics and how do we find it? The QuantISED program can exploit new capabilities provided by quantum technology to probe these kinds of science questions in new ways and over a broader range of science parameters than can be achieved with conventional techniques.

physics.ins-det↗

arXiv2020

Superconducting MoN thin films prepared by DC reactive magnetron sputtering for nanowire single-photon detectors

We present a comprehensive study of molybdenum nitride (MoN) thin film deposition using direct current (DC) reactive magnetron sputtering. We have investigated the effect of various deposition conditions on the superconducting and electrical properties of the films. Furthermore, we have shown that meander-shaped single-photon detectors made from 5 nm MoN films have saturated quantum detection efficiency at the telecom wavelength of 1550 nm. Our results indicate that MoN may be a material of interest for practical applications of low-temperature superconductors, including single-photon detectors and transition-edge sensors.

cond-mat.supr-con↗

arXiv2020

Enhancing the Performance of Superconducting Nanowire-Based Detectors with High-Filling Factor by Using Variable Thickness

Current crowding at bends of superconducting nanowire single-photon detectors is one of the main factors limiting the performance of meander-style detectors with large filling factors. In this paper, we propose a new concept to reduce influence of the current crowding effect, a so-called variable thickness SNSPD, which is composed of two regions with different thicknesses. A larger thickness of bends in comparison to the thickness of straight nanowire sections locally reduces the current density and reduces the suppression of the critical current caused by the current crowding. This allows variable thickness SNSPD to have a higher critical current, an improved detection efficiency, and decreased dark count rate in comparison with a standard uniform thickness SNSPD with an identical geometry and film quality.

cond-mat.supr-con↗

arXiv2020

Electron energy relaxation in disordered superconducting NbN films

We report on the inelastic-scattering rate of electrons on phonons and relaxation of electron energy studied by means of magnetoconductance, and photoresponse, respectively, in a series of strongly disordered superconducting NbN films. The studied films with thicknesses in the range from 3 to 33 nm are characterized by different Ioffe-Regel parameters but an almost constant product q_Tl(q_T is the wave vector of thermal phonons and l is the elastic mean free path of electrons). In the temperature range 14-30 K, the electron-phonon scattering rates obey temperature dependencies close to the power law 1/τ_{e-ph} \sim T^n with the exponents n = 3.2-3.8. We found that in this temperature range τ_{e-ph} and n of studied films vary weakly with the thickness and square resistance. At 10 K electron-phonon scattering times are in the range 11.9-17.5 ps. The data extracted from magnetoconductance measurements were used to describe the experimental photoresponse with the two-temperature model. For thick films, the photoresponse is reasonably well described without fitting parameters, however, for thinner films, the fit requires a smaller heat capacity of phonons. We attribute this finding to the reduced density of phonon states in thin films at low temperatures. We also show that the estimated Debye temperature in the studied NbN films is noticeably smaller than in bulk material.

cond-mat.supr-con↗

arXiv2020

Large-area microwire MoSi single-photon detectors at 1550 nm wavelength

We demonstrate saturated internal detection efficiency at 1550 nm wavelengths for meander-shaped superconducting nanowire single-photon detectors made of 3 nm thick MoSi films with widths of 1 and 3 $μm$, and active areas up to 400 by 400 $μm^2$. Despite hairpin turns and a large number of squares (up to $10^4$) in the device, the dark count rate was measured to be ~10$^3$ cps at 99% of the switching current. This value is about two orders of magnitude lower than results reported recently for short MoSi devices with shunt resistors. We also found that 5 nm thick MoSi detectors with the same geometry were insensitive to single near-infrared photons, which may be associated with different levels of suppression of the superconducting order parameter. However, our results obtained on 3 nm thick MoSi devices are in a good agreement with predictions in the frame of a kinetic-equation approach.

physics.app-ph↗

arXiv2020

Superconducting Nanowire Fabrication on Niobium Nitride using Helium Ion Irradiation

Superconducting devices are prone to reduced performance caused by impurities and defects along the edges of their wires, which can lead to local current crowding. In this study, we explored the use of helium ion irradiation to modify the lattice structure of the superconducting material to change its intrinsic properties. The process will allow us to directly pattern devices and potentially improve the quality of the nanowires. To achieve this, we used the ion beam from a scanning helium ion microscope (HIM) to localize damage on a superconducting material to create a nanowire. Two experiments were performed in this study. First, a range of helium ion doses was exposed on a niobium nitride (NbN) microwire to determine the estimated dose density to suppress superconductivity. Using the results of this first experiment, nanowires were patterned onto a microwire, and the current-voltage characteristics were measured for each sample. Our results showed that helium ion irradiation is an effective resistless fabrication method for superconducting nanowires.

cond-mat.supr-con↗

arXiv2019

Measuring thickness in thin NbN films for superconducting devices

We present the use of a commercially available fixed-angle multi-wavelength ellipsometer for quickly measuring the thickness of NbN thin films for the fabrication and performance improvement of superconducting nanowire single photon detectors. The process can determine the optical constants of absorbing thin films, removing the need for inaccurate approximations. The tool can be used to observe oxidation growth and allows thickness measurements to be integrated into the characterization of various fabrication processes.

physics.app-ph↗

arXiv2019

Detecting Dark Matter with Superconducting Nanowires

We propose the use of superconducting nanowires as both target and sensor for direct detection of sub-GeV dark matter. With excellent sensitivity to small energy deposits on electrons, and demonstrated low dark counts, such devices could be used to probe electron recoils from dark matter scattering and absorption processes. We demonstrate the feasibility of this idea using measurements of an existing fabricated tungsten-silicide nanowire prototype with 0.8 eV energy threshold and 4.3 nanograms with 10 thousand seconds of exposure, which showed no dark counts. The results from this device already place meaningful bounds on dark matter-electron interactions, including the strongest terrestrial bounds on sub-eV dark photon absorption to date. Future expected fabrication on larger scales and with lower thresholds should enable probing new territory in the direct detection landscape, establishing the complementarity of this approach to other existing proposals.

hep-ph↗

arXiv2018

Enhancement of optical response in nanowires by negative-tone PMMA lithography

The method of negative-tone-PMMA electron-beam lithography is investigated to improve the performance of nanowire-based superconducting detectors. Using this approach, the superconducting nanowire single-photon detectors (SNSPDs) have been fabricated from thick 5-nm NbN film sputtered at the room temperature. To investigate the impact of this process, SNSPDs were prepared by positive-tone and negative-tone-PMMA lithography, and their electrical and photodetection characteristics at 4.2 K were compared. The SNSPDs made by negative-tone-PMMA lithography show higher critical-current density and higher photon count rate at various wavelengths. Our results suggest a higher negative-tone-PMMA technology may be preferable to the standard positive-tone-PMMA lithography for this application.

physics.app-ph↗