Searcharxiv⌕ Search

arXiv subjects

J. Lange

Publications and source records attributed to J. Lange.

36 records · Page 2Linked to original sources

Radiation Hardness of Thin Low Gain Avalanche Detectors

Low Gain Avalanche Detectors (LGAD) are based on a n++-p+-p-p++ structure where an appropriate doping of the multiplication layer (p+) leads to high enough electric fields for impact ionization. Gain factors of few tens in charge significantly improve the resolution of timing measurements, particularly for thin detectors, where the timing performance was shown to be limited by Landau fluctuations. The main obstacle for their operation is the decrease of gain with irradiation, attributed to effective acceptor removal in the gain layer. Sets of thin sensors were produced by two different producers on different substrates, with different gain layer doping profiles and thicknesses (45, 50 and 80 um). Their performance in terms of gain/collected charge and leakage current was compared before and after irradiation with neutrons and pions up to the equivalent fluences of 5e15 cm-2. Transient Current Technique and charge collection measurements with LHC speed electronics were employed to characterize the detectors. The thin LGAD sensors were shown to perform much better than sensors of standard thickness (~300 um) and offer larger charge collection with respect to detectors without gain layer for fluences <2e15 cm-2. Larger initial gain prolongs the beneficial performance of LGADs. Pions were found to be more damaging than neutrons at the same equivalent fluence, while no significant difference was found between different producers. At very high fluences and bias voltages the gain appears due to deep acceptors in the bulk, hence also in thin standard detectors.

physics.ins-det↗

Systematic challenges for future gravitational wave measurements of precessing binary black holes

The properties of precessing, coalescing binary black holes are presently inferred through comparison with two approximate models of compact binary coalescence. In this work we show these two models often disagree substantially when binaries have modestly large spins ($a\gtrsim 0.4$) and modest mass ratios ($q\gtrsim 2$). We demonstrate these disagreements using standard figures of merit and the parameters inferred for recent detections of binary black holes. By comparing to numerical relativity, we confirm these disagreements reflect systematic errors. We provide concrete examples to demonstrate that these systematic errors can significantly impact inferences about astrophysically significant binary parameters. For the immediate future, parameter inference for binary black holes should be performed with multiple models (including numerical relativity), and carefully validated by performing inference under controlled circumstances with similar synthetic events.

gr-qc↗

The swiss army knife of job submission tools: grid-control

Grid-control is a lightweight and highly portable open source submission tool that supports virtually all workflows in high energy physics (HEP). Since 2007 it has been used by a sizeable number of HEP analyses to process tasks that sometimes consist of up 100k jobs. grid-control is built around a powerful plugin and configuration system, that allows users to easily specify all aspects of the desired workflow. Job submission to a wide range of local or remote batch systems or grid middleware is supported. Tasks can be conveniently specified through the parameter space that will be processed, which can consist of any number of variables and data sources with complex dependencies on each other. Dataset information is processed through a configurable pipeline of dataset filters, partition plugins and partition filters. The partition plugins can take the number of files, size of the work units, metadata or combinations thereof into account. All changes to the input datasets or variables are propagated through the processing pipeline and can transparently trigger adjustments to the parameter space and the job submission. While the core functionality is completely experiment independent, integration with the CMS computing environment is provided by a small set of plugins.

cs.DC↗

Radiation hardness of small-pitch 3D pixel sensors up to HL-LHC fluences

A new generation of 3D silicon pixel detectors with a small pixel size of 50$\times$50 and 25$\times$100 $μ$m$^{2}$ is being developed for the HL-LHC tracker upgrades. The radiation hardness of such detectors was studied in beam tests after irradiation to HL-LHC fluences up to $1.4\times10^{16}$ n$_{\mathrm{eq}}$/cm$^2$. At this fluence, an operation voltage of only 100 V is needed to achieve 97% hit efficiency, with a power dissipation of 13 mW/cm$^2$ at -25$^{\circ}$C, considerably lower than for previous 3D sensor generations and planar sensors.

physics.ins-det↗

Gain and time resolution of 45 $μ$m thin Low Gain Avalanche Detectors before and after irradiation up to a fluence of $10^{15}$ n$_{eq}$/cm$^2$

Low Gain Avalanche Detectors (LGADs) are silicon sensors with a built-in charge multiplication layer providing a gain of typically 10 to 50. Due to the combination of high signal-to-noise ratio and short rise time, thin LGADs provide good time resolutions. LGADs with an active thickness of about 45 $μ$m were produced at CNM Barcelona. Their gains and time resolutions were studied in beam tests for two different multiplication layer implantation doses, as well as before and after irradiation with neutrons up to $10^{15}$ n$_{eq}$/cm$^2$. The gain showed the expected decrease at a fixed voltage for a lower initial implantation dose, as well as for a higher fluence due to effective acceptor removal in the multiplication layer. Time resolutions below 30 ps were obtained at the highest applied voltages for both implantation doses before irradiation. Also after an intermediate fluence of $3\times10^{14}$ n$_{eq}$/cm$^2$, similar values were measured since a higher applicable reverse bias voltage could recover most of the pre-irradiation gain. At $10^{15}$ n$_{eq}$/cm$^2$, the time resolution at the maximum applicable voltage of 620 V during the beam test was measured to be 57 ps since the voltage stability was not good enough to compensate for the gain layer loss. The time resolutions were found to follow approximately a universal function of gain for all implantation doses and fluences.

physics.ins-det↗

Validating gravitational-wave detections: The Advanced LIGO hardware injection system

Hardware injections are simulated gravitational-wave signals added to the Laser Interferometer Gravitational-wave Observatory (LIGO). The detectors' test masses are physically displaced by an actuator in order to simulate the effects of a gravitational wave. The simulated signal initiates a control-system response which mimics that of a true gravitational wave. This provides an end-to-end test of LIGO's ability to observe gravitational waves. The gravitational-wave analyses used to detect and characterize signals are exercised with hardware injections. By looking for discrepancies between the injected and recovered signals, we are able to characterize the performance of analyses and the coupling of instrumental subsystems to the detectors' output channels. This paper describes the hardware injection system and the recovery of injected signals representing binary black hole mergers, a stochastic gravitational wave background, spinning neutron stars, and sine-Gaussians.

astro-ph.IM↗

Module production of the one-arm AFP 3D pixel tracker

The ATLAS Forward Proton (AFP) detector is designed to identify events in which one or two protons emerge intact from the LHC collisions. AFP will consist of a tracking detector, to measure the momentum of the protons, and a time of flight system to reduce the background from multiple proton-proton interactions. Following an extensive qualification period, 3D silicon pixel sensors were selected for the AFP tracker. The sensors were produced at CNM (Barcelona) during 2014. The tracker module assembly and quality control was performed at IFAE during 2015. The assembly of the first AFP arm and the following installation in the LHC tunnel took place in February 2016. This paper reviews the fabrication process of the AFP tracker focusing on the pixel modules.

physics.ins-det↗

3D silicon pixel detectors for the High-Luminosity LHC

3D silicon pixel detectors have been investigated as radiation-hard candidates for the innermost layers of the HL-LHC upgrade of the ATLAS pixel detector. 3D detectors are already in use today in the ATLAS IBL and AFP experiments. These are based on 50x250 um2 large pixels connected to the FE-I4 readout chip. Detectors of this generation were irradiated to HL-LHC fluences and demonstrated excellent radiation hardness with operational voltages as low as 180 V and power dissipation of 12--15 mW/cm2 at a fluence of about 1e16 neq/cm2, measured at -25 degree C. Moreover, to cope with the higher occupancies expected at the HL-LHC, a first run of a new generation of 3D detectors designed for the HL-LHC was produced at CNM with small pixel sizes of 50x50 and 25x100 um2, matched to the FE-I4 chip. They demonstrated a good performance in the laboratory and in beam tests with hit efficiencies of about 97% at already 1--2V before irradiation.

physics.ins-det↗

Beam tests of an integrated prototype of the ATLAS Forward Proton detector

The ATLAS Forward Proton (AFP) detector is intended to measure protons scattered at small angles from the ATLAS interaction point. To this end, a combination of 3D Silicon pixel tracking modules and Quartz-Cherenkov time-of-flight (ToF) detectors is installed 210m away from the interaction point at both sides of ATLAS. Beam tests with an AFP prototype detector combining tracking and timing sub-detectors and a common readout have been performed at the CERN-SPS test-beam facility in November 2014 and September 2015 to complete the system integration and to study the detector performance. The successful tracking-timing integration was demonstrated. Good tracker hit efficiencies above 99.9% at a sensor tilt of 14°, as foreseen for AFP, were observed. Spatial resolutions in the short pixel direction with 50 μm pitch of 5.5 +/- 0.5 μm per pixel plane and of 2.8 +/- 0.5 μm for the full four-plane tracker at 14° were found, largely surpassing the AFP requirement of 10 μm. The timing detector showed also good hit efficiencies above 99%, and a full-system time resolution of 35 +/- 6 ps was found for the ToF prototype detector with two Quartz bars in-line (half the final AFP size) without dedicated optimisation, fulfilling the requirements for initial low-luminosity AFP runs.

physics.ins-det↗

3D sensors for the HL-LHC

In order to increase its discovery potential, the Large Hadron Collider (LHC) accelerator will be upgraded in the next decade. The high luminosity LHC (HL-LHC) period demands new sensor technologies to cope with increasing radiation fluences and particle rates. The ATLAS experiment will replace the entire inner tracking detector with a completely new silicon-only system. 3D pixel sensors are promising candidates for the innermost layers of the Pixel detector due to their excellent radiation hardness at low operation voltages and low power dissipation at moderate temperatures. Recent developments of 3D sensors for the HL-LHC are presented.

physics.ins-det↗

Formation of ultracold dipolar molecules in the lowest vibrational levels by photoassociation

We recently reported the formation of ultracold LiCs molecules in the rovibrational ground state X1Sigma+,v''=0,J''=0 [J. Deiglmayr et al., PRL 101, 133004 (2008)]. Here we discuss details of the experimental setup and present a thorough analysis of the photoassociation step including the photoassociation line shape. We predict the distribution of produced ground state molecules using accurate potential nergy curves combined with an ab-initio dipole transition moment and compare this prediction with experimental ionization spectra. Additionally we improve the value of the dissociation energy for the X1Sigma+ state by high resolution spectroscopy of the vibrational ground state.

physics.atom-ph↗

Formation of ultracold polar molecules in the rovibrational ground state

Ultracold LiCs molecules in the absolute ground state X$^1Σ^+$, v"=0, J"=0 are formed via a single photo-association step starting from laser-cooled atoms. The selective production of v"=0, J"=2 molecules with a 50-fold higher rate is also demonstrated. The rotational and vibrational state of the ground state molecules is determined in a setup combining depletion spectroscopy with resonant-enhanced multi-photon ionization time-of-flight spectroscopy. Using the determined production rate of up to 5x10^3 molecules/s, we describe a simple scheme which can provide large samples of externally and internally cold dipolar molecules.

quant-ph↗

Experimental time-resolved photoemission and ab initio study of lifetimes of excited electrons in Mo and Rh

We have studied the relaxation dynamics of optically excited electrons in molybdenum and rhodium by means of time resolved two-photon photoemission spectroscopy (TR-2PPE) and ab initio electron self-energy calculations performed within the GW and GW+T approximations. Both theoretical approaches reproduce qualitatively the experimentally observed trends and differences in the lifetimes of excited electrons in molybdenum and rhodium. For excitation energies exceeding the Fermi energy by more than 1 eV, the GW+T theory yields lifetimes in quantitative agreement with the experimental results. As one of the relevant mechanisms causing different excited state lifetime in Mo and Rh we identify the occupation of the 4d bands. An increasing occupation of the 4d bands results in an efficient decrease of the lifetime even for rather small excitation energies of a few 100 meV.

cond-mat.other↗

Energy-resolved electron-spin dynamics at surfaces of p-doped GaAs

Electron-spin relaxation at different surfaces of p-doped GaAs is investigated by means of spin, time and energy resolved 2-photon photoemission. These results are contrasted with bulk results obtained by time-resolved Faraday rotation measurements as well as calculations of the Bir-Aronov-Pikus spin-flip mechanism. Due to the reduced hole density in the band bending region at the (100) surface the spin-relaxation time increases over two orders of magnitude towards lower energies. At the flat-band (011) surface a constant spin relaxation time in agreement with our measurements and calculations for bulk GaAs is obtained.

cond-mat.mtrl-sci↗

Photoassociation inside an optical dipole trap: absolute rate coefficients and Franck-Condon factors

We present quantitative measurements of the photoassociation of cesium molecules inside a far-detuned optical dipole trap. A model of the trap depletion dynamics is derived which allows to extract absolute photoassociation rate coefficients for the initial single-photon photoassociation step from measured trap-loss spectra. The sensitivity of this approach is demonstrated by measuring the Franck-Condon modulation of the weak photoassociation transitions into the low vibrational levels of the outer well of the 0g- state that correlates to the 6s+6p3/2 asymptote. The measurements are compared to theoretical predictions. In a magneto-optical trap these transitions have previously only been observed indirectly through ionization of ground state molecules.

physics.atom-ph↗

Saturation of Cs2 Photoassociation in an Optical Dipole Trap

We present studies of strong coupling in single-photon photoassociation of cesium dimers using an optical dipole trap. A thermodynamic model of the trap depletion dynamics is employed to extract absolute rate coefficents. From the dependence of the rate coefficient on the photoassociation laser intensity, we observe saturation of the photoassociation scattering probability at the unitarity limit in quantitative agreement with the theoretical model by Bohn and Julienne [Phys. Rev. A, 60, 414 (1999)]. Also the corresponding power broadening of the resonance width is measured. We could not observe an intensity dependent light shift in contrast to findings for lithium and rubidium, which is attributed to the absence of a p or d-wave shape resonance in cesium.

physics.atom-ph↗

Precision Pion-Proton Elastic Differential Cross Sections at Energies Spanning the Delta Resonance

A precision measurement of absolute pi+p and pi-p elastic differential cross sections at incident pion laboratory kinetic energies from T_pi= 141.15 to 267.3 MeV is described. Data were obtained detecting the scattered pion and recoil proton in coincidence at 12 laboratory pion angles from 55 to 155 degrees for pi+p, and six angles from 60 to 155 degrees for pi-p. Single arm measurements were also obtained for pi+p energies up to 218.1 MeV, with the scattered pi+ detected at six angles from 20 to 70 degrees. A flat-walled, super-cooled liquid hydrogen target as well as solid CH2 targets were used. The data are characterized by small uncertainties, ~1-2% statistical and ~1-1.5% normalization. The reliability of the cross section results was ensured by carrying out the measurements under a variety of experimental conditions to identify and quantify the sources of instrumental uncertainty. Our lowest and highest energy data are consistent with overlapping results from TRIUMF and LAMPF. In general, the Virginia Polytechnic Institute SM95 partial wave analysis solution describes our data well, but the older Karlsruhe-Helsinki PWA solution KH80 does not.

nucl-ex↗

The hyperfine transition in light muonic atoms of odd Z

The hyperfine (hf) transition rates for muonic atoms have been re-measured for select light nuclei, using neutron detectors to evaluate the time dependence of muon capture. For $^{19}$F $Λ$$_{h}$ = 5.6 (2) $μ$s$^{-1}$ for the hf transition rate, a value which is considerably more accurate than previous measurements. Results are also reported for Na, Al, P, Cl, and K; that result for P is the first positive identification.

nucl-ex↗