SearcharxivSearch

arXiv subjects

J. Yu

Publications and source records attributed to J. Yu.

At least 73 records · Page 4Linked to original sources

Long distance contribution to the $K_L-K_S$ mass difference

We develop and demonstrate techniques needed to compute the long distance contribution to the $K_{L}$-$K_{S}$ mass difference, $ΔM_K$, in lattice QCD and carry out a first, exploratory calculation of this fundamental quantity. The calculation is performed on 2+1 flavor, domain wall fermion, $16^3\times32$ configurations with a 421 MeV pion mass and an inverse lattice spacing $1/a=1.73$ GeV. We include only current-current operators and drop all disconnected and double penguin diagrams. The short distance part of the mass difference in a 2+1 flavor calculation contains a quadratic divergence cut off by the lattice spacing. Here, this quadratic divergence is eliminated through the GIM mechanism by introducing a valence charm quark. The inclusion of the charm quark makes the complete calculation accessible to lattice methods provided the discretization errors associated with the charm quark can be controlled. The long distance effects are discussed for each parity channel separately. While we can see a clear signal in the parity odd channel, the signal to noise ratio in the parity even channel is exponentially decreasing as the separation between the two weak operators increases. We obtain a mass difference $ΔM_K$ which ranges from $6.58(30)\times 10^{-12}$ MeV to $11.89(81)\times 10^{-12}$ MeV for kaon masses varying from 563 MeV to 839 MeV. Extensions of these methods are proposed which promise accurate results for both $ΔM_K$ and $ε_K$, including long distance effects.

hep-lat

Parallaxes of five L Dwarfs with a Robotic Telescope

We report the parallax and proper motion of five L dwarfs obtained with observations from the robotic Liverpool Telescope. Our derived proper motions are consistent with published values and have considerably smaller errors. Based on our spectral type versus absolute magnitude diagram, we do not find any evidence for binaries among our sample, or, at least no comparable mass binaries. Their space velocities locate them within the thin disk and based on the model comparisons they have solar-like abundances. For all five objects, we derived effective temperature, luminosity, radius, gravity and mass from a evolutionary model(CBA00) and our measured parallax; moreover, we derived their effective temperature by integrating observed optical and near-infrared spectra and model spectra (BSH06 or BT-Dusty respectively) at longer wavelengths to obtain bolometric {\bf flux using} the classical Stefan-Boltzmann law: generally the three temperatures for one object derived using two different methods with three models are consistent, while at lower temperature(e.g. for L4) the differences among the three temperatures are slightly larger than that at higher temperature(e.g. for L1).

astro-ph.SR

Micro-Pattern Gas Detectors for Charged-Particle Tracking and Muon Detection

In the context of the 2013 APS-DPF Snowmass summer study conducted by the U.S. HEP community, this white paper outlines a roadmap for further development of Micro-pattern Gas Detectors for tracking and muon detection in HEP experiments. We briefly discuss technical requirements and summarize current capabilities of these detectors with a focus of operation in experiments at the energy frontier in the medium-term to long-term future. Some key directions for future R&D on Micro-pattern Gas Detectors in the U.S. are suggested.

physics.ins-det

Temperature Evolution of Itinerant Ferromagnetism in SrRuO3 Probed by Optical Spectroscopy

The temperature ($T$) dependence of the optical conductivity spectra $σ(ω)$ of a single crystal SrRuO$_3$ thin film is studied over a $T$ range from 5 to 450 K. We observed significant $T$ dependence of the spectral weights of the charge transfer and interband $d$-$d$ transitions across the ferromagnetic Curie temperature ($T_c$ ~ 150 K). Such $T$ dependence was attributed to the increase in the Ru spin moment, which is consistent with the results of density functional theory calculations. $T$ scans of $σ(Ω, T)$ at fixed frequencies $Ω$ reveal a clear $T^2$ dependence below $T_c$, demonstrating that the Stoner mechanism is involved in the evolution of the electronic structure. In addition, $σ(Ω, T)$ continues to evolve at temperatures above $T_c$, indicating that the local spin moment persists in the paramagnetic state. This suggests that SrRuO$_3$ is an intriguing oxide system with itinerant ferromagnetism.

cond-mat.str-el

Track segments in hadronic showers in a highly granular scintillator-steel hadron calorimeter

We investigate the three dimensional substructure of hadronic showers in the CALICE scintillator-steel hadronic calorimeter. The high granularity of the detector is used to find track segments of minimum ionising particles within hadronic showers, providing sensitivity to the spatial structure and the details of secondary particle production in hadronic cascades. The multiplicity, length and angular distribution of identified track segments are compared to GEANT4 simulations with several different shower models. Track segments also provide the possibility for in-situ calibration of highly granular calorimeters.

physics.ins-det

Hadronic energy resolution of a highly granular scintillator-steel hadron calorimeter using software compensation techniques

The energy resolution of a highly granular 1 m3 analogue scintillator-steel hadronic calorimeter is studied using charged pions with energies from 10 GeV to 80 GeV at the CERN SPS. The energy resolution for single hadrons is determined to be approximately 58%/sqrt(E/GeV}. This resolution is improved to approximately 45%/sqrt(E/GeV) with software compensation techniques. These techniques take advantage of the event-by-event information about the substructure of hadronic showers which is provided by the imaging capabilities of the calorimeter. The energy reconstruction is improved either with corrections based on the local energy density or by applying a single correction factor to the event energy sum derived from a global measure of the shower energy density. The application of the compensation algorithms to Geant4 simulations yield resolution improvements comparable to those observed for real data.

physics.ins-det

Crystal field splitting and correlation effect on the electronic structure of A2IrO3

The electronic structure of the honeycomb lattice iridates Na2IrO3 and Li2IrO3 has been investigated using resonant inelastic x-ray scattering (RIXS). Crystal-field split d-d excitations are resolved in the high-resolution RIXS spectra. In particular, the splitting due to non-cubic crystal fields, derived from the splitting of j_eff=3/2 states, is much smaller than the typical spin-orbit energy scale in iridates, validating the applicability of j_eff physics in A2IrO3. We also find excitonic enhancement of the particle-hole excitation gap around 0.4 eV, indicating that the nearest-neighbor Coulomb interaction could be large. These findings suggest that both Na2IrO3 and Li2IrO3 can be described as spin-orbit Mott insulators, similar to the square lattice iridate Sr2IrO4.

cond-mat.str-el

THGEM-based detectors for sampling elements in DHCAL: laboratory and beam evaluation

We report on the results of an extensive R&D program aimed at the evaluation of Thick-Gas Electron Multipliers (THGEM) as potential active elements for Digital Hadron Calorimetry (DHCAL). Results are presented on efficiency, pad multiplicity and discharge probability of a 10x10 cm2 prototype detector with 1 cm2 readout pads. The detector is comprised of single- or double-THGEM multipliers coupled to the pad electrode either directly or via a resistive anode. Investigations employing standard discrete electronics and the KPiX readout system have been carried out both under laboratory conditions and with muons and pions at the CERN RD51 test beam. For detectors having a charge-induction gap, it has been shown that even a ~6 mm thick single-THGEM detector reached detection efficiencies above 95%, with pad-hit multiplicity of 1.1-1.2 per event; discharge probabilities were of the order of 1e-6 - 1e-5 sparks/trigger, depending on the detector structure and gain. Preliminary beam tests with a WELL hole-structure, closed by a resistive anode, yielded discharge probabilities of <2e-6 for an efficiency of ~95%. Methods are presented to reduce charge-spread and pad multiplicity with resistive anodes. The new method showed good prospects for further evaluation of very thin THGEM-based detectors as potential active elements for DHCAL, with competitive performances, simplicity and robustness. Further developments are in course.

physics.ins-det

Application of Large Scale GEM for Digital Hadron Calorimetry

The High Energy Physics group of the University of Texas at Arlington Physics Department has been developing Gas Electron Multiplier (GEM) detectors for use as the sensitive gap detector in digital hadron calorimeters (DHCAL) for the future International Linear Collider. In this study, two kinds of prototype GEM detectors have been tested. One has 30x30 cm2 active area double GEM structure with a 3 mm drift gap, a 1 mm transfer gap and a 1 mm induction gap. The other one has two 2x2 cm2 GEM foils in the amplifier stage with a 5 mm drift gap, a 2 mm transfer gap and a 1 mm induction gap. We present characteristics of these detectors obtained using high-energy charged particles, cosmic ray muons and 106Ru and 55Fe radioactive sources. From the 55Fe tests, we observed two well-separated X-ray emission peaks and measured the chamber gain to be over 6500 with a high voltage of 395 V across each GEM electrode. Both the spectra from cosmic rays and the 106Ru fit well to Landau distributions as expected from minimum ionizing particles. We also present the chamber performance after high dosage exposure to radiation as well as the pressure dependence of the gain and correction factors. Finally, we discuss the quality test results of the first set of large scale GEM foils and discuss progress and future plans for constructing large scale (100cmx100cm) GEM detectors.

physics.ins-det

Development of Large Area GEM Chambers

The High Energy Physics group of the University of Texas at Arlington Physics Department has been developing Gas Electron Multiplier (GEM) detectors for use as the sensitive gap detector in digital hadron calorimeters (DHCAL) for the future International Linear Collider. In this study, two kinds of prototype GEM detectors have been tested. One has 30x30 cm2 active area double GEM structure with a 3 mm drift gap, a 1 mm transfer gap and a 1 mm induction gap. The other one has two 2x2 cm2 GEM foils in the amplifier stage with a 5 mm drift gap, a 2 mm transfer gap and a 1 mm induction gap. We present characteristics of these detectors obtained using high-energy charged particles, cosmic ray muons and 106Ru and 55Fe radioactive sources. From the 55Fe tests, we observed two well-separated X-ray emission peaks and measured the chamber gain to be over 6500 with a high voltage of 395 V across each GEM electrode. Both the spectra from cosmic rays and the 106Ru fit well to Landau distributions as expected from minimum ionizing particles. We also present the chamber performance after high dosage exposure to radiation as well as the pressure dependence of the gain and correction factors. Finally, we discuss the quality test results of the first set of large scale GEM foils and discuss progress and future plans for constructing large scale (100cmx100cm) GEM detectors.

physics.ins-det

Electromagnetic response of a highly granular hadronic calorimeter

The CALICE collaboration is studying the design of high performance electromagnetic and hadronic calorimeters for future International Linear Collider detectors. For the hadronic calorimeter, one option is a highly granular sampling calorimeter with steel as absorber and scintillator layers as active material. High granularity is obtained by segmenting the scintillator into small tiles individually read out via silicon photo-multipliers (SiPM). A prototype has been built, consisting of thirty-eight sensitive layers, segmented into about eight thousand channels. In 2007 the prototype was exposed to positrons and hadrons using the CERN SPS beam, covering a wide range of beam energies and incidence angles. The challenge of cell equalization and calibration of such a large number of channels is best validated using electromagnetic processes. The response of the prototype steel-scintillator calorimeter, including linearity and uniformity, to electrons is investigated and described.

physics.ins-det

Handbook of LHC Higgs Cross Sections: 1. Inclusive Observables

This Report summarizes the results of the first 10 months' activities of the LHC Higgs Cross Sections Working Group. The main goal of the working group was to present the status-of-art on Higgs Physics at the LHC integrating all new results that have appeared in the last few years. The Report is more than a mere collection of the proceedings of the general meetings. The subgroups have been working in different directions. An attempt has been made to present the first Report from these subgroups in a complete and homogeneous form. The subgroups' contributions correspondingly comprise the main parts of the Report. A significant amount of work has been performed in providing higher-order corrections to the Higgs-boson cross sections and pinning down the theoretical uncertainty of the Standard Model predictions. This Report comprises explicit numerical results on total cross sections, leaving the issues of event selection cuts and differential distributions to future publications. The subjects for further study are identified.

hep-ph

Progress in the Development of Plasma Panel Radiation Detectors

Plasma Display Panels (PDP), the underlying engine of panel plasma television displays, are being investigated for their utility as radiation detectors called Plasma Panel Sensors (PPS). The PPS a novel variant of a micropattern radiation detector, is intended to be a fast, high resolution detector comprised of an array of plasma discharge cells operating in a hermetically sealed gas mixture. We report on the PPS development effort, including recent laboratory measurements.

physics.ins-det

Summary of the Linear Collider Testbeam Workshop 2009 - LCTW09

This note summarises the workshop LCTW09 held between the 3.11.2009 and 5.11.2009 at LAL Orsay. The workshop was dedicated to discuss the beam tests in the years 2010 up to 2013 for detectors to be operated at a future linear electron positron collider. The document underlines the rich R&D program on these detectors in the coming years. Large synergies were identified in the DAQ and software systems. Considerable consolidation of resources are expected from the establishment of semi-permanent beam lines for linear collider detector R&D at major centres like CERN and FNAL. Reproducing a beam structure as foreseen for the International Linear Collider (ILC) would clearly enhance the value of the obtained beam test results. Although not ultimately needed for every research program, all groups would exploit such a feature if it is available.

physics.ins-det

Study of the interactions of pions in the CALICE silicon-tungsten calorimeter prototype

A prototype silicon-tungsten electromagnetic calorimeter for an ILC detector was tested in 2007 at the CERN SPS test beam. Data were collected with electron and hadron beams in the energy range 8 to 80 GeV. The analysis described here focuses on the interactions of pions in the calorimeter. One of the main objectives of the CALICE program is to validate the Monte Carlo tools available for the design of a full-sized detector. The interactions of pions in the Si-W calorimeter are therefore confronted with the predictions of various physical models implemented in the GEANT4 simulation framework.

physics.ins-det

Construction and Commissioning of the CALICE Analog Hadron Calorimeter Prototype

An analog hadron calorimeter (AHCAL) prototype of 5.3 nuclear interaction lengths thickness has been constructed by members of the CALICE Collaboration. The AHCAL prototype consists of a 38-layer sandwich structure of steel plates and highly-segmented scintillator tiles that are read out by wavelength-shifting fibers coupled to SiPMs. The signal is amplified and shaped with a custom-designed ASIC. A calibration/monitoring system based on LED light was developed to monitor the SiPM gain and to measure the full SiPM response curve in order to correct for non-linearity. Ultimately, the physics goals are the study of hadron shower shapes and testing the concept of particle flow. The technical goal consists of measuring the performance and reliability of 7608 SiPMs. The AHCAL was commissioned in test beams at DESY and CERN. The entire prototype was completed in 2007 and recorded hadron showers, electron showers and muons at different energies and incident angles in test beams at CERN and Fermilab.

physics.ins-det

Two-Dimensional Confinement of 3d1 Electrons in LaTiO3/LaAlO3 Multilayers

We report spectroscopic ellipsometry measurements of the anisotropy of the interband transitions parallel and perpendicular to the planes of (LaTiO3)n(LaAlO3)5 multilayers with n = 1-3. These provide direct information about the electronic structure of the two-dimensional (2D) 3d^1 state of the Ti ions. In combination with LDA+U calculations, we suggest that 2D confinement in the TiO2 slabs lifts the degeneracy of the t_{2g} states leaving only the planar d_xy orbitals occupied. We outline that these multilayers can serve as a model system for the study of the t_{2g} 2D Hubbard model.

cond-mat.str-el

The electronic structure of epitaxially stabilized 5d perovskite Ca_{1-x}Sr_xIrO_3 (x = 0, 0.5, and 1) thin films: the role of strong spin-orbit coupling

We have investigated the electronic structure of meta-stable perovskite Ca1-xSrxIrO3 (x = 0, 0.5, and 1) thin films using transport measurements, optical spectroscopy, and first-principles calculations. We artificially fabricated the perovskite phase of Ca1-xSrxIrO3, which has a hexagonal or post perovskite crystal structure in bulk form, by growing epitaxial thin films on perovskite GdScO3 substrates using epi-stabilization technique. The transport properties of the perovskite Ca1-xSrxIrO3 films systematically changed from nearly insulating (or semi-metallic) for x = 0 to bad metallic for x = 1. Due to the extended wavefunctions, 5d electrons are usually delocalized. However, the strong spin-orbit coupling in Ca1-xSrxIrO3 results in the formation of effective total angular momentum Jeff = 1/2 and 3/2 states, which puts Ca1-xSrxIrO3 in the vicinity of a metal-insulator phase boundary. As a result, the electrical properties of the Ca1-xSrxIrO3 films are found to be sensitive to x and strain.

cond-mat.str-el