arXiv subjects

Jaafar M. H. Elmirghani

Publications and source records attributed to Jaafar M. H. Elmirghani.

At least 55 records · Page 3Linked to original sources

arXiv2022

OWC-enabled Spine and Leaf Architecture Towards Energy Efficient Data Center Networks

Due to the emergence of new paradigms and services such as 5G/6G, IoT, and more, current deployed wired Data Center Networks (DCNs) are not meeting the required performance metrics due to their limited reconfigurability, scalability, and throughput. To that end, wireless DCNs using technologies such as Optical Wireless Communication (OWC) have become viable and costeffective solutions as they offer higher capacity, better energy efficiency, and better scalability. This paper proposes an OWC-based spine and leaf DCNs where the leaf switches are enabled with OWC transceivers, and the spine switches are replaced by Access Points (APs) in the ceiling connected to a backbone network. The APs are interconnected through a Passive Optical Network (PON) that also connects the architecture with upper network layers. An Infrared (IR) OWC system that employs Wavelength Division Multiplexing (WDM) is proposed to enhance the DCN downlink communication. The simulation (i.e., channel modeling) results show that our proposed data center links achieve good data rates in the data center up to 15 Gbps. For the PON, Arrayed Waveguide Grating Routers (AWGRs) that enable WDM are proposed to connect the APs. We evaluate the performance of the considered architecture in term of its power efficiency compared to traditional spine and leaf data centers. The results show that the OWC-enabled DCN reduces the power consumption by 42% compared to traditional the spine and leaf architecture.

cs.NI↗

arXiv2022

On the energy efficiency of Laser-based Optical Wireless Networks

Optical wireless Communication (OWC) is a strong candidate in the next generation (6G) of cellular networks. In this paper, a laser-based optical wireless network is deployed in an indoor environment using Vertical Cavity Surface Emitting Lasers (VCSELS) as transmitters serving multiple users. Specifically, a commercially available low-cost VCSEL operating at 850nm wavelength is used. Considering the confined coverage area of each VCSEL, an array of VCSELs is designed to transmit data to multiple users through narrow beams taking into account eye safety regulations. To manage multi-user interference (MUI), Zero Forcing (ZF) is implemented to maximize the multiplexing gain of the network. The energy efficiency of the network is studied under different laser beam waists to find the effective laser beam size that results in throughput enhancement. The results show that the energy efficiency increases with the laser beam waist. Moreover, using micro lenses placed in front of the VCSELs leads to significant increase in the energy efficiency.

eess.SP↗

arXiv2022

Energy Efficient PON Backhaul Network for a VLC Based Fog Architecture

In this paper, an energy efficient passive optical network (PON) architecture is proposed for backhaul connectivity in indoor visible light communication (VLC) systems. The proposed network is used to support a fog computing architecture allowing users with processing demands to access dedicated fog nodes and idle processing resources in other user devices within a building. The fog resources within a building complement fog nodes at higher layers of the access and metro networks and the central cloud data center. A mixed integer linear programming (MILP) model is developed to minimize the total power consumption associated with serving demands over the proposed architecture. The results show that the PON backhaul network improves the energy efficiency of fog computing by 66% for networking and 12% for processing compared to an architecture based on state-of-the-art Spine-and-Leaf connectivity.

cs.NI↗

arXiv2022

Random Linear Network Coding in NOMA Optical Wireless Networks

Optical wireless communication (OWC) has the potential to provide high communication speeds that support the massive use of the Internet that is expected in the near future. In OWC, optical access points (APs) are deployed on the celling to serve multiple users. In this context, efficient multiple access schemes are required to share the resources among the users and align multi-user interference. Recently, non-orthogonal multiple access (NOMA) has been studied to serve multiple users simultaneously using the same resources, while a different power level is allocated to each user. Despite the acceptable performance of NOMA, users might experience a high packet loss due to high noise, which results from the use of successive interference cancelation (SIC). In this work, random linear network coding (RLNC) is proposed to enhance the performance of NOMA in an optical wireless network where users are divided into multicast groups, and each group contains users that slightly differ in their channel gains. Moreover, a fixed power allocation (FPA) strategy is considered among these groups to avoid complexity. The performance of the proposed scheme is evaluated in terms of total packet success probability. The results show that the proposed scheme is more suitable for the network considered compared to other benchmark schemes such as traditional NOMA and orthogonal transmission schemes. Moreover, the total packet success probability is highly affected by the level of power allocated to each group in all the scenarios.

cs.IT↗

arXiv2021

Optical Wireless Sytems for Spine and Leaf Data Center Downlinks

The continually growing demands for traffic as a result of advanced technologies in 5G and 6G systems offering services with intensive demands such as IoT and virtual reality applications has resulted in significant performance expectations of data center networks (DCNs). More specifically, DCNs are expected to meet high bandwidth connectivity, high throughput, low latency, and high scalability requirements. However, the current wired DCN architectures introduce large cabling requirements and limit the ability to reconfigure data centres as they expand. To that end, wireless technologies such as Optical Wireless Communication (OWC) have been proposed as a viable and cost-effective solution to meet the aforementioned requirements. This paper proposes the use of Infrared (IR) OWC systems that employ Wavelength Division Multiplexing (WDM) to enhance the DCN communication in the downlink direction; i.e. from Access Points (APs) in the ceiling, connected to spine switches, to receivers attached to the top of the racks representing leaf switches. The proposed systems utilize Angle Diversity Transmitters (ADTs) mounted on the room ceiling to facilitate inter-rack communication. Two different optical receiver types are considered, namely Angle Diversity Receivers (ADRs) and Wide Field-of-View Receivers (WFOVR). The simulation (i.e. channel modeling) results show that our proposed data center links achieve good data rates in the data centre up to 15 Gbps.

cs.NI↗

arXiv2021

Towards Terabit LiFi Networking

Light Fidelity (Li-Fi) is a networked version of optical wireless communication (OWC), which is a strong candidate to fulfill the unprecedented increase in user-traffic expected in the near future. In OWC, a high number of optical access points (APs) is usually deployed on the ceiling of an indoor environment to serve multiple users with different demands. Despite the high data rates of OWC networks, due to the use of the optical band for data transmission, they cannot replace current radio frequency (RF) wireless networks where OWC has several issues including the small converge area of an optical AP, the lack of uplink transmission and high blockage probabilities. However, OWC has the potential to support the requirements in the next generation (6G) of wireless communications. In this context, heterogeneous optical/RF networks can be considered to overcome the limitations of OWC and RF systems, while providing a high quality of service in terms of achievable data rates and coverage. In this work, infrared lasers, vertical-cavity surface-emitting(VCSEL) lasers, are used as the key elements of optical APs for serving multiple users. Then, transmission schemes such as zero forcing (ZF) and blind interference alignment (BIA) are introduced to manage multi-user interference and maximize the sum rate of users. Moreover, a WiFi system is considered to provide uplink transmission and serve users that experience a low signal to noise ratio (SNR) from the optical system. To use the resources of the heterogeneous optical/RF network efficiently, we derive a utility-based objective function that aims to maximize the overall sum rate of the network.

eess.SP↗

arXiv2021

Artificial Neural Network for Resource Allocation in Laser-based Optical wireless Networks

Optical wireless communication offers unprecedented communication speeds that can support the massive use of the Internet on a daily basis. In indoor environments, optical wireless networks are usually multi-user multiple-input multiple-output (MU-MIMO) systems, where a high number of optical access points (APs) is required to ensure coverage. In this work, a laser-based optical wireless network is considered for serving multiple users. Moreover, blind inference alignment (BIA) is implemented to achieve a high degree of freedom (DoF) without the need for channel state information (CSI) at transmitters, which is difficult to provide in such wireless networks. Then, an objective function is defined to allocate the resources of the network taking into consideration the requirements of users and the available resources. This optimization problem can be solved through exhaustive search or distributed algorithms. However, a practical algorithm that provides immediate solutions in real time scenarios is required. In this context, an artificial neural network (ANN) model is derived in order to obtain a sub-optimal solution with low computational time. The implementation of the ANN model involves three important steps, dataset generation, offline training, and real time application. The results show that the trained ANN model provides a significant solution close to the optimal one.

eess.SP↗

arXiv2021

Resource Allocation in Laser-based Optical Wireless Cellular Networks

Optical wireless communication provides data transmission at high speeds which can satisfy the increasing demands for connecting a massive number of devices to the Internet. In this paper, vertical-cavity surface-emitting(VCSEL) lasers are used as transmitters due to their high modulation speed and energy efficiency. However, a high number of VCSEL lasers is required to ensure coverage where each laser source illuminates a confined area. Therefore, multiple users are classified into different sets according to their connectivity. Given this point, a transmission scheme that uses blind interference alignment (BIA) is implemented to manage the interference in the laser-based network. In addition, an optimization problem is formulated to maximize the utility sum rate taking into consideration the classification of the users. To solve this problem, a decentralized algorithm is proposed where the main problem is divided into sub-problems, each can be solved independently avoiding complexity. The results demonstrate the optimality of the decentralized algorithm where a sub-optimal solution is provided. Finally, it is shown that BIA can provide high performance in laser-based networks compared with zero forcing (ZF) transmit precoding scheme.

eess.SP↗

arXiv2021

On Optimizing Rate Splitting in Laser-based Optical Wireless Networks

Optical wireless communication (OWC) is a promising technology that has the potential to provide Tb/s aggregate rates. In this paper, interference management is studied in a Laser-based optical wireless network where vertical-cavity surface-emitting (VCSEL) lasers are used for data transmission. In particular, rate splitting (RS) and hierarchical rate splitting (HRS) are proposed to align multi-user interference, while maximizing the multiplexing gain of the network. Basically, RS serves multiple users simultaneously by splitting a message of a user into common and private messages, each message with a certain level of power, while on the other side users decode their messages following a specific methodology. The performance of the conventional RS scheme is limited in high density wireless networks. Therefore, the HRS scheme is developed aiming to achieve high rates where users are divided into multiple groups, and a new message called outer common message is used for managing inter-group interference. We formulate an optimization problem that addresses power allocation among the messages of the HRS scheme to further enhance the performance of the network. The results show that the proposed approach provides high achievable rates compared with the conventional RS and HRS schemes in different scenarios.

cs.IT↗

arXiv2021

Optimized Passive Optical Networks with Cascaded-AWGRs for Data Centers

The use of Passive Optical Networks (PONs) in modern and future data centers can provide energy efficiency, high capacity, low cost, scalability, and elasticity. This paper introduces a passive optical network design with 2-tier cascaded Arrayed Waveguide Grating Routers (AWGRs) to connect groups of racks (i.e. cells) within a data center. This design employs a Software-Defined Networking (SDN) controller to manage the routing and assignment of the networking resource while introducing multiple paths between any two cells to improve routing, load balancing and resilience. We provide benchmarking results for the power consumption to compare the energy efficiency of this design to state-of-the-art data centers. The results indicate that the cascaded AWGRs architecture can achieve up to 43% saving in the networking power consumption compared to Fat-Tree data center architecture.

cs.NI↗

arXiv2021

Angle Diversity Trasmitter For High Speed Data Center Uplink Communications

This paper proposes an uplink optical wireless communication (OWC) link design that can be used by data centers to support communication in spine and leaf architectures between the top of rack leaf switches and large spine switches whose access points are mounted in the ceiling. The use of optical wireless links reduces cabling and allows easy reconfigurability for example when data centres expand. We consider three racks in a data center where each rack contains an Angle Diversity Transmitter (ADT) positioned on the top of the rack to realize the uplink function of a top-of-the-rack (ToR) or a leaf switch. Four receivers are considered to be installed on the ceiling where each is connected to a spine switch. Two types of optical receivers are studied which are a Wide Field-of-View Receiver (WFOVR) and an Angle Diversity Receiver (ADR). The performance of the proposed system is evaluated when the links run at data rates higher than 19 Gbps. The results indicate that the proposed approach achieves excellent performance using simple On-Off Keying (OOK)

eess.SP↗

arXiv2021

Energy Efficient Resource Allocation in Federated Fog Computing Networks

There is a continuous growth in demand for time sensitive applications which has shifted the cloud paradigm from a centralized computing architecture towards distributed heterogeneous computing platforms where resources located at the edge of the network are used to provide cloud-like services. This paradigm is widely known as fog computing. Virtual machines (VMs) have been widely utilized in both paradigms to enhance the network scalability, improve resource utilization, and energy efficiency. Moreover, Passive Optical Networks (PONs) are a technology suited to handling the enormous volumes of data generated in the access network due to their energy efficiency and large bandwidth. In this paper, we utilize a PON to provide the connectivity between multiple distributed fog units to achieve federated (i.e. cooperative) computing units in the access network to serve intensive demands. We propose a mixed integer linear program (MILP) to optimize the VM placement in the federated fog computing units with the objective of minimizing the total power consumption while considering inter-VM traffic. The results show a significant power saving as a result of the proposed optimization model by up to 52%, in the VM-allocation compared to a baseline approach that allocates the VM requests while neglecting the power consumption and inter-VMs traffic in the optimization framework.

cs.NI↗

arXiv2021

Blind Interference Alignment in 6G Optical Wireless Communications

In recent years, the demand for high speed wireless networking has increased considerably due to the enormous number of devices connected to the Internet. In this context, optical wireless communication (OWC) has received tremendous interest in the context of next generation wireless networks where OWC offers a huge unlicensed bandwidth using optical bands. OWC systems are directional and can naturally provide multiple-input and multiple-output (MIMO) configurations serving multiple users using a high number of transmitters in the indoor environment to ensure coverage. Therefore, multiuser interference must be managed efficiently to enhance the performance of OWC networks considering different metrics. A transmission scheme referred to as blind interference alignment (BIA) is proposed for OWC systems to maximize the multiplexing gain without the need for channel state information (CSI) at the transmitters, which is difficult to achieve in MIMO scenarios. However, standard BIA avoids the need for CSI at the cost of requiring channel coherence time large enough for transmitting the whole transmission block. Moreover, the methodology of BIA results in increased noise with increase in the number of transmitters and users. Therefore, various network topologies such as network centric (NC) and user centric (UC) designs are proposed to relax the limitations of BIA where these topologies divide the receiving area into multiple clusters. The results show a significant enhancement in the performance of topological BIA compared with standard BIA.

cs.IT↗

arXiv2021

Reinforcement Learning for Resource Allocation in Steerable Laser-based Optical Wireless Systems

Vertical Cavity Surface Emitting Lasers (VCSELs) have demonstrated suitability for data transmission in indoor optical wireless communication (OWC) systems due to the high modulation bandwidth and low manufacturing cost of these sources. Specifically, resource allocation is one of the major challenges that can affect the performance of multi-user optical wireless systems. In this paper, an optimisation problem is formulated to optimally assign each user to an optical access point (AP) composed of multiple VCSELs within a VCSEL array at a certain time to maximise the signal to interference plus noise ratio (SINR). In this context, a mixed-integer linear programming (MILP) model is introduced to solve this optimisation problem. Despite the optimality of the MILP model, it is considered impractical due to its high complexity, high memory and full system information requirements. Therefore, reinforcement Learning (RL) is considered, which recently has been widely investigated as a practical solution for various optimization problems in cellular networks due to its ability to interact with environments with no previous experience. In particular, a Q-learning (QL) algorithm is investigated to perform resource management in a steerable VCSEL-based OWC systems. The results demonstrate the ability of the QL algorithm to achieve optimal solutions close to the MILP model. Moreover, the adoption of beam steering, using holograms implemented by exploiting liquid crystal devices, results in further enhancement in the performance of the network considered.

eess.SP↗

arXiv2021

Network Topologies for Composable Data Centres

Suitable composable data center networks (DCNs) are essential to support the disaggregation of compute components in highly efficient next generation data centers (DCs). However, designing such composable DCNs can be challenging. A composable DCN that adopts a full mesh backplane between disaggregated compute components within a rack and employs dedicated interfaces on each point-to-point link is wasteful and expensive. In this paper, we propose and describe two (i.e., electrical, and electrical-optical) variants of a network for composable DC (NetCoD). NetCoD adopts a targeted design to reduce the number of transceivers required when a mesh physical backplane is deployed between disaggregated compute components in the same rack. The targeted design leverages optical communication techniques and components to achieve this with minimal or no network performance degradation. We formulate a MILP model to evaluate the performance of both variants of NetCoD in rack-scale composable DCs that implement different forms of disaggregation. The electrical-optical variant of NetCoD achieves similar performance as a reference network while utilizing fewer transceivers per compute node. The targeted adoption of optical technologies by both variants of NetCoD achieves greater (4 - 5 times greater) utilization of available network throughput than the reference network which implements a generic design. Under the various forms of disaggregation considered, both variant of NetCoD achieve near-optimal compute energy efficiency in the composable DC while satisfying both compute and network constraints. This is because marginal concession of optimal compute energy efficiency is often required to achieve overall optimal energy efficiency in composable DCs.

cs.NI↗

arXiv2021

Optical Networks for Composable Data Centers

Composable data centers (DCs) have been proposed to enable greater efficiencies as the uptake of on-demand computing services grows. In this article we give an overview of composable DCs by discussing their enabling technologies, benefits, challenges, and research directions. We then describe a network for composable DCs that leverages optical communication technologies and components to implement a targeted design. Relative to the implementation of a generic design that requires a (high capacity) dedicated transceiver on each point-to-point link on a mesh optical fabric in a composable DC rack, the targeted design can significantly reduce capital expenditure (by up to 34 times) because fewer transceivers are used. This is achieved with little or no degradation of expected performance in composable DCs.

cs.NI↗

arXiv2021

Rate Splitting in VCSEL-based Optical Wireless Networks

Optical wireless communication is an effective potential solution for enabling high speed next generation cellular networks. In this paper, laser sources, in particular, vertical-cavity surface-emitting (VCSEL) lasers are used for data transmission due to their high modulation speed compared with light emitting diode (LED) sources. To manage multi-user interference, rate splitting (RS) is implemented where the message of a user is split into common and private parts. However, the performance of RS is limited in high density networks. Therefore, hierarchical rate splitting (HRS) particularly suited in high density networks is considered. The results demonstrate the high data rate achieved by using VCSELs. Moreover, HRS is more suitable for achieving high performance in optical networks compared with RS.

eess.SP↗

arXiv2021

Q-learning algorithm for resource allocation in WDMA-based optical wireless communication networks

Visible Light Communication (VLC) has been widely investigated during the last decade due to its ability to provide high data rates with low power consumption. In general, resource management is an important issue in cellular networks that can highly effect their performance. In this paper, an optimisation problem is formulated to assign each user to an optimal access point and a wavelength at a given time. This problem can be solved using mixed integer linear programming (MILP). However, using MILP is not considered a practical solution due to its complexity and memory requirements. In addition, accurate information must be provided to perform the resource allocation. Therefore, the optimisation problem is reformulated using reinforcement learning (RL), which has recently received tremendous interest due to its ability to interact with any environment without prior knowledge. In this paper, we investigate solving the resource allocation optimisation problem in VLC systems using the basic Q-learning algorithm. Two scenarios are simulated to compare the results with the previously proposed MILP model. The results demonstrate the ability of the Q-learning algorithm to provide optimal solutions close to the MILP model without prior knowledge of the system.

cs.NI↗