arXiv subjects

Jessica L. McChesney

Publications and source records attributed to Jessica L. McChesney.

At least 19 recordsLinked to original sources

arXiv2026

Thermally Desorbable InN Capping Layers for Nitride Surface Science

Group III-nitride thin films are essential for optoelectronic and power devices, where surface and interface quality critically influence performance. It is often necessary to transfer these films through atmosphere for processing or characterization steps, which can introduce significant surface contamination. Here we demonstrate a technique to protect the surface of III-N films during atmospheric exposure by capping with sacrificial InN layers. Using molecular beam epitaxy grown AlGaN films as our representative protected material, we take advantage of the lower decomposition and desorption temperatures of InN and metallic In to remove the protective cap layer in situ via thermal desorption without damaging the AlGaN film beneath. Angle-resolved photoemission spectroscopy (ARPES) measurements of the valence band dispersion in Al0.4Ga0.6N demonstrate that the film surface is recovered after InN decapping, highlighting the versatility of this process in allowing further surface-sensitive characterization of films that had been exposed to air.

cond-mat.mtrl-sci↗

arXiv2026

Crystal growth and characterization of the ultra-high temperature substrate $\mathrm{Ta_{1-x}Hf_{x}C_{0.5}}$

Incorporation of $\mathrm{Al_{y}Ga_{1-y}N}$ (AGN) semiconductors into high power electronics offers efficiency improvements in power transmission, generation, and use, if approaches to eliminate the defects arising from film-lattice mismatch can be established. Here, we report the optical floating zone crystal growth of $\mathrm{Ta_{1-x}Hf_{x}C_{0.5}}$ (x = 0.2), a new metallic substrate material family lattice matched to the ultra-wide-band-gap, Al-rich side (y = 0.91) of the AGN solid solution. Laue diffraction demonstrates large single crystal domains in the as-grown boule. Single crystal x-ray diffraction at T = 213 K in conjunction with first principles calculations shows that the material adopts a layered crystal structure with AA-type stacking of (Ta/Hf)-C-(Ta/Hf) trilayers described in the trigonal space group P-3m1 (#164), with a = 3.1168(4) Å, c = 4.9644(4) Å, and $β$ = 120.0°. X-ray photoelectron spectroscopy (XPS) measurements show the Hf:Ta ratio to be close to the nominal value of 0.8:0.2 in the grown crystal. Density Functional Theory calculations reveal that this structure is stabilized by the low energy of carbon-vacancy formation of a hypothetical $\mathrm{(Ta/Hf)_{1}C_{1}}$ anti-NiAs structure type, and imply flexibility in interface structure with an overlayer nitride film. A surface preparation/polishing procedure is developed that reduces root mean square (RMS) surface roughness from as-cut 130 nm to 7 nm as measured by atomic force microscopy. Scanning electron microscopy shows the presence of a native surface oxide, removed by polishing, along with carbon-rich pits. Time-domain thermoreflectance measurements show a room temperature thermal conductivity of $κ$ = 18.1(4) W m-1 K-1. These results provide key first steps for utilizing metallic, lattice matched, substrates for the growth of Al-rich AGN semiconductors.

cond-mat.mtrl-sci↗

arXiv2026

Electronic origin of delicate antiferromagnetism in Fe$_{x}$NbS$_2$

Among the family of intercalated transition-metal dichalcogenides (TMDs), Fe$_{x}$NbS$_2$ is found to possess unique current-induced resistive switching behaviors, tunable antiferromagnetic states, and a commensurate charge order, all of which are tied to a critical Fe doping of $x_c$ = 1/3. However, the electronic origin of such extreme stoichiometry sensitivities remains unclear. Combining angle-resolved photoemission spectroscopy (ARPES) with density functional theory (DFT) calculations, we identify and characterize a dramatic eV-scale electronic restructuring that occurs across the $x_c$. Moment-carrying Fe 3$d_{z^2}$ electrons manifest as narrow bands within 200 meV of the Fermi level, distinct from other transition metal intercalated TMD magnets. These states strongly hybridize with itinerant electrons in TMD layer, rapidly lose coherence above $x_c$ due to correlation-driven effects. This sudden quasiparticle decoherence collapses the Fe-Nb hybridization, which explicitly suppresses the out-of-plane effective Fe-Fe exchange interaction, driving the transformation of the magnetic ground state from an antiferromagnetic stripe phase to a zigzag phase. These observations resemble the exceptional electronic and magnetic sensitivity of strongly correlated systems, and demonstrate that quantifying orbital-specific hybridization via ARPES offers an alternative pathway to evaluate effective magnetic exchange in metallic magnets, complementing inelastic neutron and resonant x-ray scattering probes.

cond-mat.str-el↗

arXiv2026

Epitaxial stabilization of magnetic GdAuSb/LaAuSb superlattices

We report the epitaxial stabilization of GdAuSb films and GdAuSb/LaAuSb superlattices via molecular beam epitaxy on (0001)-oriented Al$_{2}$O$_{3}$ substrates. GdAuSb crystallize in the Au-Au dimerized YPtAs structure type (space group $P6_{3}/mmc$), the same structure as the Dirac semimetal LaAuSb. Angle-resolved photoemission spectroscopy (ARPES) measurements show similar near $E_F$ bandstructures for GdAuSb and LaAuSb, plus a rigid band shift for GdAuSb towards more hole-like behavior and core-like Gd $4f$ states $\sim 9$~eV below the Fermi energy. LaAuSb/GdAuSb superlattices exhibit sharp superlattice fringes by X-ray diffraction and atomically-precise interfaces by scanning transmission electron microscopy. Superlattices display two transitions in temperature-dependent resistvity, compared to a single Néel temperature for thick GdAuSb films. Superlattices of $Ln$AuSb materials ($Ln=$ rare earth) with atomically abrupt interfaces offer a new epitaxial platform for control of magnetic and topological order via tunable intralayer exchange and reduced dimensionality.

cond-mat.mtrl-sci↗

arXiv2025

A high-speed, high-resolution Transition Edge Sensor spectrometer for soft X-rays at the Advanced Photon Source

This project explores the design and development of a transition edge sensor (TES) spectrometer for resonant soft X- ray scattering (RSXS) measurements developed in collaboration between Argonne National Laboratory (ANL) and the National Institute of Standards and Technology (NIST). Soft X-ray scattering is a powerful technique for studying the electronic and magnetic properties of materials on a microscopic level. However, the lack of high-performance soft X-ray spectrometers has limited the potential of this technique. TES spectrometers have the potential to overcome these limitations due to their high energy resolution, high efficiency, and broad energy range. This project aims to optimize the design of a TES spectrometer for RSXS measurements and more generally soft X-ray spectroscopy at the Advanced Photon Source (APS) 29-ID, leading to improved understanding of advanced materials. We will present a detailed description of the instrument design and implementation. The spectrometer consists of a large array of approximately 250 high-speed and high-resolution pixels. The pixels have saturation energies of approximately 1 keV, sub-ms pulse duration and energy resolution of approximately 1 eV. The array is read out using microwave multiplexing chips with MHz bandwidth per channel, enabling efficient data throughput. To facilitate measurement of samples in situ under ultra-high vacuum conditions at the beamline, the spectrometer is integrated with an approximately 1 m long snout.

physics.ins-det↗

arXiv2024

Signatures of polarized chiral spin disproportionation in rare earth nickelates

In rare earth nickelates (RENiO$_3$), electron-lattice coupling drives a concurrent metal-to-insulator and bond disproportionation phase transition whose microscopic origin has long been the subject of active debate. Of several proposed mechanisms, here we test the hypothesis that pairs of self-doped ligand holes spatially condense to provide local spin moments that are antiferromagnetically coupled to Ni spins. These singlet-like states provide a basis for long-range bond and spiral spin order. Using magnetic resonant X-ray scattering on NdNiO$_3$ thin films, we observe the chiral nature of the spin-disproportionated state, with spin spirals propagating along the crystallographic (101)$_\mathrm{ortho}$ direction. These spin spirals are found to preferentially couple to X-ray helicity, establishing the presence of a hitherto-unobserved macroscopic chirality. The presence of this chiral magnetic configuration suggests a potential multiferroic coupling between the noncollinear magnetic arrangement and improper ferroelectric behavior as observed in prior studies on NdNiO$_3$ (101)$_\mathrm{ortho}$ films and RENiO$_3$ single crystals. Experimentally constrained theoretical double-cluster calculations confirm the presence of an energetically stable spin-disproportionated state with Zhang-Rice singlet-like combinations of Ni and ligand moments.

cond-mat.str-el↗

arXiv2022

Controlling the balance between remote, pinhole, and van der Waals epitaxy of Heusler films on graphene/sapphire

Remote epitaxy on monolayer graphene is promising for synthesis of highly lattice mismatched materials, exfoliation of free-standing membranes, and re-use of expensive substrates. However, clear experimental evidence of a remote mechanism remains elusive. In many cases, due to contaminants at the transferred graphene/substrate interface, alternative mechanisms such as pinhole-seeded lateral epitaxy or van der Waals epitaxy can explain the resulting exfoliatable single-crystalline films. Here, we find that growth of the Heusler compound GdPtSb on clean graphene on sapphire substrates produces a 30 degree rotated epitaxial superstructure that cannot be explained by pinhole or van der Waals epitaxy. With decreasing growth temperature the volume fraction of this 30 degree domain increases compared to the direct epitaxial 0 degree domain, which we attribute to slower surface diffusion at low temperature that favors remote epitaxy, compared to faster surface diffusion at high temperature that favors pinhole epitaxy. We further show that careful graphene/substrate annealing ($T\sim 700 ^\circ C$) and consideration of the film/substrate vs film/graphene lattice mismatch are required to obtain epitaxy to the underlying substrate for a variety of other Heusler films, including LaPtSb and GdAuGe. The 30 degree rotated superstructure provides a possible experimental fingerprint of remote epitaxy since it is inconsistent with the leading alternative mechanisms.

cond-mat.mtrl-sci↗

arXiv2022

Strain-induced enhancement of $T_c$ in infinite-layer Pr$_{0.8}$Sr$_{0.2}$NiO$_2$ films

The mechanism of unconventional superconductivity in correlated materials remains a great challenge in condensed matter physics. The recent discovery of superconductivity in infinite-layer nickelates, as analog to high-Tc cuprates, has opened a new route to tackle this challenge. By growing 8 nm Pr0.8Sr0.2NiO2 films on the (LaAlO3)0.3(Sr2AlTaO6)0.7 substrate, we successfully raise the transition temperature Tc from 9 K in the widely studied SrTiO3-substrated nickelates into 15 K. By combining x-ray absorption spectroscopy with the first-principles and many-body simulations, we find a positive correlation between Tc and the pre-edge peak intensity, which can be attributed to the hybridization between Ni and O orbitals induced by the strain. Our result suggests that structural engineering can further enhance unconventional superconductivity, and the charge-transfer property plays a crucial role in the pairing strength.

cond-mat.supr-con↗

arXiv2022

Electronic structure of superconducting nickelates probed by resonant photoemission spectroscopy

The discovery of infinite-layer nickelate superconductors has spurred enormous interest. While the Ni$^{1+}$ cations possess nominally the same 3$d^9$ configuration as Cu$^{2+}$ in cuprates, the electronic structure variances remain elusive. Here, we present a soft x-ray photoemission spectroscopy study on parent and doped infinite-layer Pr-nickelate thin films with a doped perovskite reference. By identifying the Ni character with resonant photoemission and comparison to density functional theory + U (on-site Coulomb repulsion energy) calculations, we estimate U ~5 eV, smaller than the charge transfer energy $Δ$ ~8 eV, confirming the Mott-Hubbard electronic structure in contrast to charge-transfer cuprates. Near the Fermi level ($E_F$), we observe a signature of occupied rare-earth states in the parent compound, which is consistent with a self-doping picture. Our results demonstrate a correlation between the superconducting transition temperature and the oxygen 2$p$ hybridization near $E_F$ when comparing hole-doped nickelates and cuprates.

cond-mat.supr-con↗

arXiv2021

Band Engineering of Dirac Semimetals using Charge Density Waves

New developments in the field of topological matter are often driven by materials discovery, including novel topological insulators, Dirac semimetals and Weyl semimetals. In the last few years, large efforts have been performed to classify all known inorganic materials with respect to their topology. Unfortunately, a large number of topological materials suffer from non-ideal band structures. For example, topological bands are frequently convoluted with trivial ones, and band structure features of interest can appear far below the Fermi level. This leaves just a handful of materials that are intensively studied. Finding strategies to design new topological materials is a solution. Here we introduce a new mechanism that is based on charge density waves and non-symmorphic symmetry to design an idealized Dirac semimetal. We then show experimentally that the antiferromagnetic compound GdSb$_{0.46}$Te$_{1.48}$ is a nearly ideal Dirac semimetal based on the proposed mechanism, meaning that most interfering bands at the Fermi level are suppressed. Its highly unusual transport behavior points to a thus far unknown regime, in which Dirac carriers with Fermi energy very close to the node seem to gradually localize in the presence of lattice and magnetic disorder.

cond-mat.mtrl-sci↗

arXiv2021

Search for $Q \sim 0$ order near a forbidden Bragg position in Bi$_{2.1}$Sr$_{1.9}$CaCu$_2$O$_{8+x}$ with resonant soft x-ray scattering

Identifying what broken symmetries are present in the cuprates has become a major area of research. Many authors have reported evidence for so-called "$Q \sim 0$" order that involves broken inversion, mirror, chiral, or time-reversal symmetry that is uniform in space. Not all these observations are well understood and new experimental probes are needed. Here we use resonant soft x-ray scattering (RSXS) to search for $Q \sim 0$ order in Bi$_{2.1}$Sr$_{1.9}$CaCu$_2$O$_{8+x}$ (Bi-2212) by measuring the region of a forbidden Bragg peak, $(0,0,3)$, which is normally extinguished by symmetry but may become allowed on resonance if valence band order is present. Using circularly polarized light, we found that this reflection becomes allowed on the Cu $L_3$ resonance for temperatures $T_c < T < T^\ast$, though remains absent in linear polarization and at other temperatures. This observation suggests the existence of spatially uniform valence band order near the pseudogap temperature. In addition, we observed periodic oscillations in the specular reflectivity from the sample surface that resemble thin film interference fringes, though no known film is present. These fringes are highly resonant, appear in all polarizations, and exhibit a period that depends on the location where the beam strikes the sample surface. We speculate that these fringes arise from interaction between some intrinsic valence band instability and extrinsic structural surface morphologies of the material. Our study supports the existence of some kind of $Q \sim 0$ broken symmetry state in Bi-2212 at intermediate temperatures, and calls for further study using a microfocused beam that could disentangle microscopic effects from macroscopic heterogeneities.

cond-mat.str-el↗

arXiv2019

High electrical conductivity in the epitaxial polar metals LaAuGe and LaPtSb

Polar metals are an intriguing class of materials that simultaneously host free carriers and polar structural distortions. Despite the name "polar metal," however, most well-studied polar metals are poor electrical conductors. Here, we demonstrate the molecular beam epitaxial (MBE) growth of LaPtSb and LaAuGe, two polar metal compounds whose electrical resistivity is an order of magnitude lower than the well studied oxide polar metals. These materials belong to a broad family of $ABC$ intermetallics adopting the stuffed wurtzite structure, also known as hexagonal Heusler compounds. Scanning transmission electron microscopy (STEM) reveals a polar structure with unidirectionally buckled $BC$ (PtSb, AuGe) planes. Magnetotransport measurements demonstrate good metallic behavior with low residual resistivity ($ρ_{LaAuGe}=59.05$ $μΩ\cdot$cm and $ρ_{LaAPtSb}=27.81$ $μΩ\cdot$cm at 2K) and high carrier density ($n_h\sim 10^{21}$ cm$^{-3}$). Photoemission spectroscopy measurements confirm the band metallicity and are in quantitative agreement with density functional theory (DFT) calculations. Through DFT-Chemical Pressure and Crystal Orbital Hamilton Population analyses, the atomic packing factor is found to support the polar buckling of the structure, though the degree of direct interlayer $B-C$ bonding is limited by repulsion at the $A-C$ contacts. When combined with insulating hexagonal Heuslers, these materials provide a new platform for fully epitaxial, multiferroic heterostructures.

cond-mat.mtrl-sci↗

arXiv2019

High mobility in a van der Waals layered antiferromagnetic metal

Magnetic van der Waals (vdW) materials have been heavily pursued for fundamental physics as well as for device design. Despite the rapid advances, so far magnetic vdW materials are mainly insulating or semiconducting, and none of them possesses a high electronic mobility - a property that is rare in layered vdW materials in general. The realization of a magnetic high-mobility vdW material would open the possibility for novel magnetic twistronic or spintronic devices. Here we report very high carrier mobility in the layered vdW antiferromagnet GdTe3. The electron mobility is beyond 60,000 cm2 V-1 s-1, which is the highest among all known layered magnetic materials, to the best of our knowledge. Among all known vdW materials, the mobility of bulk GdTe3 is comparable to that of black phosphorus, and is only surpassed by graphite. By mechanical exfoliation, we further demonstrate that GdTe3 can be exfoliated to ultrathin flakes of three monolayers, and that the magnetic order and relatively high mobility is retained in approximately 20-nm-thin flakes.

cond-mat.mtrl-sci↗

arXiv2019

Electronically enhanced layer buckling and Au-Au dimerization in epitaxial LaAuSb films

We report the molecular beam epitaxial growth, structure, and electronic measurements of single-crystalline LaAuSb films on Al$_2$O$_3$ (0001) substrates. LaAuSb belongs to a broad family of hexagonal $ABC$ intermetallics in which the magnitude and sign of layer buckling have strong effects on properties, e.g., predicted hyperferroelecticity, polar metallicity, and Weyl and Dirac states. Scanning transmission electron microscopy reveals highly buckled planes of Au-Sb atoms, with strong interlayer Au-Au interactions and a doubling of the unit cell. This buckling is four times larger than the buckling observed in other $ABC$s with similar composition, e.g. LaAuGe and LaPtSb. Photoemission spectroscopy measurements and comparison with theory suggest an electronic driving force for the Au-Au dimerization, since LaAuSb, with a 19-electron count, has one more valence electron per formula unit than most stable $ABC$s. Our results suggest that the electron count, in addition to conventional parameters such as epitaxial strain and chemical pressure, provides a powerful means for tuning the layer buckling in ferroic $ABC$s.

cond-mat.mtrl-sci↗

arXiv2009

Quasiparticle Transformation During a Metal-Insulator Transition in Graphene

Here we show, with simultaneous transport and photoemission measurements, that the graphene terminated SiC(0001) surface undergoes a metal-insulator transition (MIT) upon dosingwith small amounts of atomic hydrogen. We find the room temperature resistance increases by about 4 orders of magnitude, a transition accompanied by anomalies in the momentum-resolved spectral function including a non-Fermi Liquid behaviour and a breakdown of the quasiparticle picture. These effects are discussed in terms of a possible transition to a strongly (Anderson) localized ground state.

cond-mat.mes-hall↗

arXiv2008

Self-consistent analysis of electron-phonon coupling parameters of graphene

We present a self-consistent analysis of the photoemission spectral function A(k, w) of graphene monolayers grown epitaxially on SiC(0001). New information derived from spectral intensity anomalies (in addition to linewidths and peak positions) confirms that sizeable kinks in the electronic dispersion at the Dirac energy ED and near the Fermi level EF arise from many-body interactions, not single-particle effects such as substrate bonding or extra bands. The relative electron-phonon scattering rate from phonons at different energy scales evolves with doping. The electron-phonon coupling strength is extracted and found to be much larger (~3.5-5 times) than predicted.

cond-mat.str-el↗

arXiv2008

Atmospheric pressure graphitization of SiC(0001)- A route towards wafer-size graphene layers

We have investigated epitaxial graphene films grown on SiC(0001) by annealing in an atmosphere of Ar instead of vacuum. Using AFM and LEEM we observe a significantly improved surface morphology and graphene domain size. Hall measurements on monolayer graphene films show a carrier mobility of around 1000 cm^2/Vs at room temperature and 2000 cm^2/Vs at 27K. The growth process introduced here establishes the synthesis of graphene films on a technologically viable basis.

cond-mat.mtrl-sci↗

arXiv2008

Van Hove Singularity and Apparent Anisotropy in the Electron-Phonon Interaction in Graphene

We show that the electron-phonon coupling strength obtained from the slopes of the electronic energy vs. wavevector dispersion relations, as often done in analyzing angle-resolved photoemission data, can differ substantially from the actual electron-phonon coupling strength due to the curvature of the bare electronic bands. This effect becomes particularly important when the Fermi level is close to a van Hove singularity. By performing {\it ab initio} calculations on doped graphene we demonstrate that, while the apparent strength obtained from the slopes of experimental photoemission data is highly anisotropic, the angular dependence of the actual electron-phonon coupling strength in this material is negligible.

cond-mat.mtrl-sci↗