arXiv subjects

Julien Woillez

Publications and source records attributed to Julien Woillez.

35 records · Page 2Linked to original sources

arXiv2021

P-REx II. Off-line Performance on VLTI/GRAVITY

For sensitive optical interferometry, it is crucial to control the evolution of the optical path difference (OPD) of the wavefront between the individual telescopes of the array. The OPD between a pair of telescopes is induced by differential optical properties such as atmospheric refraction, telescope alignment, etc. This has classically been measured using a fringe tracker that provides corrections to a piston actuator to account for this difference. An auxiliary method, known as the Piston Reconstruction Experiment (P-REx) has been developed to measure the OPD, or differential 'piston' of the wavefront, induced by the atmosphere at each telescope. Previously, this method was outlined and results obtained from LBT adaptive optics (AO) data for a single telescope aperture were presented. P-REx has now been applied off-line to previously acquired VLT's GRAVITY CIAO wavefront sensing data to estimate the atmospheric OPD for the six VLTI baselines. Comparisons with the OPD obtained from the VLTI GRAVITY fringe tracker were made. The results indicate that the telescope and instrumental noise of the combined VLTI and GRAVITY systems dominate over the atmospheric turbulence contributions. However, good agreement between simulated and on-sky P-REx data indicates that if the telescope and instrumental noise were reduced to atmospheric piston noise levels, P-REx has the potential to reduce the OPD root mean square of piston turbulence by up to a factor of 10 for frequencies down to 1 Hz. In such conditions, P-REx will assist in pushing the sensitivity limits of optical fringe tracking with long baseline interferometers.

astro-ph.IM↗

arXiv2020

Betelgeuse scope: Single-mode-fibers-assisted optical interferometer design for dedicated stellar activity monitoring

Betelgeuse has gone through a sudden shift in its brightness and dimmed mysteriously. This is likely caused by a hot blob of plasma ejected from Betelgeuse and then cooled to obscuring dust. If true, it is a remarkable opportunity to directly witness the formation of dust around a red supergiant star. Today's optical telescope facilities are not optimized for time-evolution monitoring of the Betelgeuse surface, so in this work, we propose a low-cost optical interferometer. The facility will consist of $12 \times 4$ inch optical telescopes mounted on the surface of a large radio dish for interferometric imaging; polarization-maintaining single-mode fibers will carry the coherent beams from the individual optical telescopes to an all-in-one beam combiner. A fast steering mirror assisted fiber injection system guides the flux into fibers. A metrology system senses vibration-induced piston errors in optical fibers, and these errors are corrected using fast-steering delay lines. We will present the design.

astro-ph.IM↗

arXiv2020

Infrared wavefront sensing for adaptive optics assisted Galactic Center observations with the VLT interferometer and GRAVITY: operation and results

This article describes the operation of the near-infrared wavefront sensing based Adaptive Optics (AO) system CIAO. The Coudé Infrared Adaptive Optics (CIAO) system is a central auxiliary component of the Very Large Telescope (VLT) interferometer (VLTI). It enables in particular the observations of the Galactic Center (GC) using the GRAVITY instrument. GRAVITY is a highly specialized beam combiner, a device that coherently combines the light of the four 8-m telescopes and finally records interferometric measurements in the K-band on 6 baselines simultaneously. CIAO compensates for phase disturbances caused by atmospheric turbulence, which all four 8 m Unit Telescopes (UT) experience during observation. Each of the four CIAO units generates an almost diffraction-limited image quality at its UT, which ensures that maximum flux of the observed stellar object enters the fibers of the GRAVITY beam combiner. We present CIAO performance data obtained in the first 3 years of operation as a function of weather conditions. We describe how CIAO is configured and used for observations with GRAVITY. In addition, we focus on the outstanding features of the near-infrared sensitive Saphira detector, which is used for the first time on Paranal, and show how it works as a wavefront sensor detector.

astro-ph.IM↗

arXiv2019

Single-mode interferometric field of view in partial turbulence correction. Application to the observation of the environment of Sgr A* with GRAVITY

Context. The GRAVITY instrument on the ESO VLTI is setting a new mark in the landscape of optical interferometers. Long exposures are possible for the first time in this wavelength domain, delivering a dramatic improvement for astrophysics. In particular, faint objects can be observed at the angular resolution of the VLTI, with exposures exceeding by many orders of magnitude the coherence time of atmospheric turbulence. Aims. Modern interferometers, especially those that combine light collected by large telescopes such as the Unit Telescopes of the VLT, benefit from partial correction of atmospheric turbulence. We investigate in this paper the influence of atmospheric turbulence on the maximum field of view of interferometers such as GRAVITY, where wavefronts are filtered with single-mode fibres. The basic question is whether the maximum field of view is restricted to the diffraction limit of single apertures or if it is wider in practice. We discuss in particular the case of the field around Sgr A* , with an emphasis on the detectability of the massive main-sequence star S2. Methods. We theoretically investigated the interferometric and photometric lobes of the interferometer and took atmospheric turbulence into account. We computed the lobe functions with and without partial correction for atmospheric turbulence. Results. The main result of the paper is that the field of view of the interferometer is widened by tip-tilt residues if higher orders of atmospheric turbulence are corrected for. As a particular case, the S2 star can be detected in interferometric frames centred on Sgr A* even when the distance between the two objects is up to about twice the diffraction limit of a single aperture. We also show that the visibilities are not biased in this case if the pointing accuracies of the fibres are of the order of 10 mas.

astro-ph.IM↗

arXiv2019

astroquery: An Astronomical Web-Querying Package in Python

astroquery is a collection of tools for requesting data from databases hosted on remote servers with interfaces exposed on the internet, including those with web pages but without formal application program interfaces (APIs). These tools are built on the Python requests package, which is used to make HTTP requests, and astropy, which provides most of the data parsing functionality. astroquery modules generally attempt to replicate the web page interface provided by a given service as closely as possible, making the transition from browser-based to command-line interaction easy. astroquery has received significant contributions from throughout the astronomical community, including several significant contributions from telescope archives. astroquery enables the creation of fully reproducible workflows from data acquisition through publication. This paper describes the philosophy, basic structure, and development model of the astroquery package. The complete documentation for astroquery can be found at http://astroquery.readthedocs.io/.

astro-ph.IM↗

arXiv2018

Astrometric Interferometry

Astrometry is a powerful technique in astrophysics to measure three-dimensional positions of stars and other astrophysical objects, including exoplanets and the gravitational influence they have on each other. Interferometric astrometry is presented here as just one in a suite of powerful astrometric techniques, which include space-based, seeing-limited and wide-angle adaptive optics techniques. Fundamental limits are discussed, demonstrating that even ground-based techniques have the capability for astrometry at the single micro-arcsecond level, should sufficiently sophisticated instrumentation be constructed for both the current generation of single telescopes and long-baseline optical interferometers.

astro-ph.IM↗

arXiv2018

Perspectives of a visible instrument on the VLTI

In this paper we present the most promising science cases for a new generation visible instrument on the VLTI and the conceptual idea for the instrumental configuration. We also present a statistical study of the potential targets that may be accessible for the different classes of objects and for the required spectral resolutions.

astro-ph.IM↗

arXiv2018

Characterisation of ALPAO deformable mirrors for the NAOMI VLTI Auxiliary Telescopes Adaptive Optics

The Very Large Telescope Interferometer Auxiliary Telescopes will soon be equipped with an adaptive optics system called NAOMI. The corrective optics deformable mirror is the commercial DM241 from ALPAO. Being part of an interferometer operating from visible to mid-infrared, the DMs of NAOMI face several challenges (high level of reliability, open-loop chopping, piston-free control, WFS/DM pupil rotation, high desired bandwidth and stroke). We here describe our extensive characterization of the DMs through measurements and simulations. We summarize the operational scenario we have defined to handle the specific mirror properties. We conclude that the ALPAO DMs have overall excellent properties that fulfill most of the stringent requirements and that deviations from specifications are easily handled. To our knowledge, NAOMI will be the first astronomical system with a command in true Zernike modes (allowing software rotation), and the first astronomical system in which a chopping is performed with the deformable mirror (5'' sky, at 5~Hz).

astro-ph.IM↗

arXiv2017

AGILIS: Agile Guided Interferometer for Longbaseline Imaging Synthesis - Demonstration and concepts of reconfigurable optical imaging interferometers

In comparison to the radio and sub-millimetric domains, imaging with optical interferometry is still in its infancy. Due to the limited number of telescopes in existing arrays, image generation is a demanding process that relies on time-consuming reconfiguration of the interferometer array and super-synthesis. Using single mode optical fibres for the coherent transport of light from the collecting telescopes to the focal plane, a new generation of interferometers optimized for imaging can be designed. To support this claim, we report on the successful completion of the `OHANA Iki project: an end-to-end, on-sky demonstration of a two-telescope interferometer, built around near-infrared single mode fibres, carried out as part of the `OHANA project. Having demonstrated that coherent transport by single-mode fibres is feasible, we explore the concepts, performances, and limitations of a new imaging facility with single mode fibres at its heart: Agile Guided Interferometer for Longbaseline Imaging Synthesis (AGILIS). AGILIS has the potential of becoming a next generation facility or a precursor to a much larger project like the Planet Formation Imager (PFI).

astro-ph.IM↗

arXiv2016

The 2nd Generation VLTI path to performance

The upgrade of the VLTI infrastructure for the 2nd generation instruments is now complete with the transformation of the laboratory, and installation of star separators on both the 1.8-m Auxiliary Telescopes (ATs) and the 8-m Unit Telescopes (UTs). The Gravity fringe tracker has had a full semester of commissioning on the ATs, and a first look at the UTs. The CIAO infrared wavefront sensor is about to demonstrate its performance relative to the visible wavefront sensor MACAO. First astrometric measurements on the ATs and astrometric qualification of the UTs are on-going. Now is a good time to revisit the performance roadmap for VLTI that was initiated in 2014, which aimed at coherently driving the developments of the interferometer, and especially its performance, in support to the new generation of instruments: Gravity and MATISSE.

astro-ph.IM↗

arXiv2016

Status of the Planet Formation Imager (PFI) concept

The Planet Formation Imager (PFI) project aims to image the period of planet assembly directly, resolving structures as small as a giant planet's Hill sphere. These images will be required in order to determine the key mechanisms for planet formation at the time when processes of grain growth, protoplanet assembly, magnetic fields, disk/planet dynamical interactions and complex radiative transfer all interact - making some planetary systems habitable and others inhospitable. We will present the overall vision for the PFI concept, focusing on the key technologies and requirements that are needed to achieve the science goals. Based on these key requirements, we will define a cost envelope range for the design and highlight where the largest uncertainties lie at this conceptual stage.

astro-ph.IM↗

arXiv2016

Confronting Standard Models of Proto--Planetary Disks With New Mid--Infrared Sizes from the Keck Interferometer

We present near and mid-infrared interferometric observations made with the Keck Interferometer Nuller and near-contemporaneous spectro-photometry from the IRTF of 11 well known young stellar objects, several observed for the first time in these spectral and spatial resolution regimes. With AU-level spatial resolution, we first establish characteristic sizes of the infrared emission using a simple geometrical model consisting of a hot inner rim and mid-infrared disk emission. We find a high degree of correlation between the stellar luminosity and the mid-infrared disk sizes after using near-infrared data to remove the contribution from the inner rim. We then use a semi-analytical physical model to also find that the very widely used "star + inner dust rim + flared disk" class of models strongly fails to reproduce the SED and spatially-resolved mid-infrared data simultaneously; specifically a more compact source of mid-infrared emission is required than results from the standard flared disk model. We explore the viability of a modification to the model whereby a second dust rim containing smaller dust grains is added, and find that the two-rim model leads to significantly improved fits in most cases. This complexity is largely missed when carrying out SED modelling alone, although detailed silicate feature fitting by McClure et al. 2013 recently came to a similar conclusion. As has been suggested recently by Menu et al. 2015, the difficulty in predicting mid-infrared sizes from the SED alone might hint at "transition disk"-like gaps in the inner AU; however, the relatively high correlation found in our mid-infrared disk size vs. stellar luminosity relation favors layered disk morphologies and points to missing disk model ingredients instead.

astro-ph.SR↗

arXiv2014

VLTI status update: a decade of operations and beyond

We present the latest update of the European Southern Observatory's Very Large Telescope interferometer (VLTI). The operations of VLTI have greatly improved in the past years: reduction of the execution time; better offering of telescopes configurations; improvements on AMBER limiting magnitudes; study of polarization effects and control for single mode fibres; fringe tracking real time data, etc. We present some of these improvements and also quantify the operational improvements using a performance metric. We take the opportunity of the first decade of operations to reflect on the VLTI community which is analyzed quantitatively and qualitatively. Finally, we present briefly the preparatory work for the arrival of the second generation instruments GRAVITY and MATISSE.

astro-ph.IM↗

arXiv2013

Astropy: A Community Python Package for Astronomy

We present the first public version (v0.2) of the open-source and community-developed Python package, Astropy. This package provides core astronomy-related functionality to the community, including support for domain-specific file formats such as Flexible Image Transport System (FITS) files, Virtual Observatory (VO) tables, and common ASCII table formats, unit and physical quantity conversions, physical constants specific to astronomy, celestial coordinate and time transformations, world coordinate system (WCS) support, generalized containers for representing gridded as well as tabular data, and a framework for cosmological transformations and conversions. Significant functionality is under active development, such as a model fitting framework, VO client and server tools, and aperture and point spread function (PSF) photometry tools. The core development team is actively making additions and enhancements to the current code base, and we encourage anyone interested to participate in the development of future Astropy versions.

astro-ph.IM↗

arXiv2012

First faint dual-field phase-referenced observations on the Keck interferometer

Ground-based long baseline interferometers have long been limited in sensitivity by the short integration periods imposed by atmospheric turbulence. The first observation fainter than this limit was performed on January 22, 2011 when the Keck Interferometer observed a K=11.5 target, about one magnitude fainter than its K=10.3 limit. This observation was made possible by the Dual Field Phase Referencing instrument of the ASTRA project: simultaneously measuring the real-time effects of the atmosphere on a nearby bright guide star, and correcting for it on the faint target, integration time longer than the turbulence time scale are made possible. As a prelude to this demonstration, we first present the implementation of Dual Field Phase Referencing on the interferometer. We then detail its on-sky performance focusing on the accuracy of the turbulence correction, and on the resulting fringe contrast stability. We conclude with a presentation of early results obtained with Laser Guide Star AO and the interferometer.

astro-ph.IM↗

arXiv2010

Luminosity-variation independent location of the circum-nuclear, hot dust in NGC 4151

After recent sensitivity upgrades at the Keck Interferometer (KI), systematic interferometric 2um studies of the innermost dust in nearby Seyfert nuclei are within observational reach. Here, we present the analysis of new interferometric data of NGC 4151, discussed in context of the results from recent dust reverberation, spectro-photometric and interferometric campaigns. The complete data set gives a complex picture, in particular the measured visibilities from now three different nights appear to be rather insensitive to the variation of the nuclear luminosity. KI data alone indicate two scenarios: the K-band emission is either dominated to ~90% by size scales smaller than 30mpc, which falls short of any dust reverberation measurement in NGC 4151 and of theoretical models of circum-nuclear dust distributions. Or contrary, and more likely, the K-band continuum emission is dominated by hot dust (>= 1300K) at linear scales of about 50mpc. The linear size estimate varies by a few tens of percent depending on the exact morphology observed. Our interferometric, deprojected centro-nuclear dust radius estimate of 55+-5mpc is roughly consistent with the earlier published expectations from circum-nuclear, dusty radiative transfer models, and spectro-photometric modeling. However, our data do not support the notion that the dust emission size scale follows the nuclear variability of NGC 4151 as a R_dust \propto L_nuc^0.5 scaling relation. Instead variable nuclear activity, lagging, and variable dust response to illumination changes need to be combined to explain the observations.

astro-ph.CO↗

arXiv2008

Astrometry with the Keck-Interferometer: the ASTRA project and its science

The sensitivity and astrometry upgrade ASTRA of the Keck Interferometer is introduced. After a brief overview of the underlying interferometric principles, the technology and concepts of the upgrade are presented. The interferometric dual-field technology of ASTRA will provide the KI with the means to observe two objects simultaneously, and measure the distance between them with a precision eventually better than 100 uas. This astrometric functionality of ASTRA will add a unique observing tool to fields of astrophysical research as diverse as exo-planetary kinematics, binary astrometry, and the investigation of stars accelerated by the massive black hole in the center of the Milky Way as discussed in this contribution.

astro-ph↗