arXiv subjects

Karl K. Berggren

Publications and source records attributed to Karl K. Berggren.

At least 73 records · Page 4Linked to original sources

arXiv2020

Electron-Energy Loss of Ultraviolet Plasmonic Modes in Aluminum Nanodisks

We theoretically investigated electron energy loss spectroscopy (EELS) of ultraviolet surface plasmon modes in aluminum nanodisks. Using full-wave simulations, we studied the impact of diameter on the resonant modes of the nanodisks. We found that the mode behavior can be separately classified for two distinct cases: (1) flat nanodisks where the diameter is much less than the thickness; and (2) thick nanodisks where the diameter is comparable to the thickness. While the multipolar edge modes and breathing modes of flat nanostructures have previously been interpreted using intuitive, analytical models based on surface plasmon polariton (SPP) modes of a thin-film stack, it has been found that the true dispersion relation of the multipolar edge modes deviates significantly from the SPP dispersion relation. Here, we developed a modified intuitive model that uses effective wavelength theory to accurately model this dispersion relation with significantly less computational overhead compared to full-wave electromagnetic simulations. However, for the case of thick nanodisks, this effective wavelength theory breaks down, and such intuitive models are no longer viable. We found that this is because some modes of the thick nanodisks carry a polar (i.e. out of the substrate plane, or along the electron beam direction) dependence and cannot be simply categorized as radial breathing modes or angular (azimuthal) multipolar edge modes. This polar dependence leads to radiative losses, motivating the use of simultaneous EELS and cathodoluminescence measurements when experimentally investigating the complex mode behavior of thick nanostructures.

physics.optics↗

arXiv2020

Large-area microwire MoSi single-photon detectors at 1550 nm wavelength

We demonstrate saturated internal detection efficiency at 1550 nm wavelengths for meander-shaped superconducting nanowire single-photon detectors made of 3 nm thick MoSi films with widths of 1 and 3 $μm$, and active areas up to 400 by 400 $μm^2$. Despite hairpin turns and a large number of squares (up to $10^4$) in the device, the dark count rate was measured to be ~10$^3$ cps at 99% of the switching current. This value is about two orders of magnitude lower than results reported recently for short MoSi devices with shunt resistors. We also found that 5 nm thick MoSi detectors with the same geometry were insensitive to single near-infrared photons, which may be associated with different levels of suppression of the superconducting order parameter. However, our results obtained on 3 nm thick MoSi devices are in a good agreement with predictions in the frame of a kinetic-equation approach.

physics.app-ph↗

arXiv2020

Cavity electro-optics in thin-film lithium niobate for efficient microwave-to-optical transduction

Linking superconducting quantum devices to optical fibers via microwave-optical quantum transducers may enable large scale quantum networks. For this application, transducers based on the Pockels electro-optic (EO) effect are promising for their direct conversion mechanism, high bandwidth, and potential for low-noise operation. However, previously demonstrated EO transducers require large optical pump power to overcome weak EO coupling and reach high efficiency. Here, we create an EO transducer in thin-film lithium niobate, leveraging the low optical loss and strong EO coupling in this platform. We demonstrate a transduction efficiency of up to $2.7\times10^{-5}$, and a pump-power normalized efficiency of $1.9\times10^{-6}/\mathrm{μW}$. The transduction efficiency can be improved by further reducing the microwave resonator's piezoelectric coupling to acoustic modes, increasing the optical resonator quality factor to previously demonstrated levels, and changing the electrode geometry for enhanced EO coupling. We expect that with further development, EO transducers in thin-film lithium niobate can achieve near-unity efficiency with low optical pump power.

quant-ph↗

arXiv2020

Superconducting Nanowire Fabrication on Niobium Nitride using Helium Ion Irradiation

Superconducting devices are prone to reduced performance caused by impurities and defects along the edges of their wires, which can lead to local current crowding. In this study, we explored the use of helium ion irradiation to modify the lattice structure of the superconducting material to change its intrinsic properties. The process will allow us to directly pattern devices and potentially improve the quality of the nanowires. To achieve this, we used the ion beam from a scanning helium ion microscope (HIM) to localize damage on a superconducting material to create a nanowire. Two experiments were performed in this study. First, a range of helium ion doses was exposed on a niobium nitride (NbN) microwire to determine the estimated dose density to suppress superconductivity. Using the results of this first experiment, nanowires were patterned onto a microwire, and the current-voltage characteristics were measured for each sample. Our results showed that helium ion irradiation is an effective resistless fabrication method for superconducting nanowires.

cond-mat.supr-con↗

arXiv2020

Nanostructured-membrane electron phase plates

Electron beams can acquire designed phase modulations by passing through nanostructured material phase plates. These phase modulations enable electron wavefront shaping and benefit electron microscopy, spectroscopy, lithography, and interferometry. However, in the fabrication of electron phase plates, the typically used focused-ion-beam-milling method limits the fabrication throughput and hence the active area of the phase plates. Here, we fabricated large-area electron phase plates with electron-beam lithography and reactive-ion-etching. The phase plates are characterized by electron diffraction in transmission electron microscopes with various electron energies, as well as diffractive imaging in a scanning electron microscope. We found the phase plates could produce a null in the center of the bright-field based on coherent interference of diffractive beams. Our work adds capabilities to the fabrication of electron phase plates. The nullification of the direct beam and the tunable diffraction efficiency demonstrated here also paves the way towards novel dark-field electron-microscopy techniques and tunable electron phase plates.

physics.app-ph↗

arXiv2020

Development of Quantum InterConnects for Next-Generation Information Technologies

Just as classical information technology rests on a foundation built of interconnected information-processing systems, quantum information technology (QIT) must do the same. A critical component of such systems is the interconnect, a device or process that allows transfer of information between disparate physical media, for example, semiconductor electronics, individual atoms, light pulses in optical fiber, or microwave fields. While interconnects have been well engineered for decades in the realm of classical information technology, quantum interconnects (QuICs) present special challenges, as they must allow the transfer of fragile quantum states between different physical parts or degrees of freedom of the system. The diversity of QIT platforms (superconducting, atomic, solid-state color center, optical, etc.) that will form a quantum internet poses additional challenges. As quantum systems scale to larger size, the quantum interconnect bottleneck is imminent, and is emerging as a grand challenge for QIT. For these reasons, it is the position of the community represented by participants of the NSF workshop on Quantum Interconnects that accelerating QuIC research is crucial for sustained development of a national quantum science and technology program. Given the diversity of QIT platforms, materials used, applications, and infrastructure required, a convergent research program including partnership between academia, industry and national laboratories is required. This document is a summary from a U.S. National Science Foundation supported workshop held on 31 October - 1 November 2019 in Alexandria, VA. Attendees were charged to identify the scientific and community needs, opportunities, and significant challenges for quantum interconnects over the next 2-5 years.

quant-ph↗

arXiv2019

Light Phase Detection with On-Chip Petahertz Electronic Networks

Ultrafast light-matter interactions lead to optical-field-driven photocurrents with an attosecond-level temporal response. These photocurrents can be used to detect the carrier-envelope-phase (CEP) of short optical pulses, and could be utilized to create optical-frequency, petahertz (PHz) electronics for information processing. Despite recent reports on optical-field-driven photocurrents in various nanoscale solid-state materials, little has been done in examining the large-scale integration of these devices. In this work, we demonstrate enhanced, on-chip CEP detection via optical-field-driven photocurrent in a monolithic array of electrically-connected plasmonic bow-tie nanoantennas that are contained within an area of hundreds of square microns. The technique is scalable and could potentially be used for shot-to-shot CEP tagging applications requiring orders of magnitude less pulse energy compared to alternative ionization-based techniques. Our results open new avenues for compact time-domain, on-chip CEP detection, and inform the development of integrated circuits for PHz electronics as well as integrated platforms for attosecond and strong-field science.

physics.optics↗

arXiv2019

Resolving photon numbers using a superconducting tapered nanowire detector

Time- and number-resolved photon detection is crucial for photonic quantum information processing. Existing photon-number-resolving (PNR) detectors usually have limited timing and dark-count performance or require complex fabrication and operation. Here we demonstrate a PNR detector at telecommunication wavelengths based on a single superconducting nanowire with an integrated impedance-matching taper. The prototyping device was able to resolve up to five absorbed photons and had 16.1 ps timing jitter, <2 c.p.s. device dark count rate, $\sim$86 ns reset time, and 5.6% system detection efficiency (without cavity) at 1550 nm. Its exceptional distinction between single- and two-photon responses is ideal for coincidence counting and allowed us to directly observe bunching of photon pairs from a single output port of a Hong-Ou-Mandel interferometer. This detector architecture may provide a practical solution to applications that require high timing resolution and few-photon discrimination.

physics.ins-det↗

arXiv2019

Single-Photon Single-Flux Coupled Detectors

In this work, we present a novel device that is a combination of a superconducting nanowire single-photon detector and a superconducting multi-level memory. We show that these devices can be used to count the number of detections through single-photon to single-flux conversion. Electrical characterization of the memory properties demonstrates single-flux quantum (SFQ) separated states. Optical measurements using attenuated laser pulses with different mean photon number, pulse energies and repetition rates are shown to differentiate single-photon detection from other possible phenomena, such as multi-photon detection and thermal activation. Finally, different geometries and material stacks to improve device performance, as well as arraying methods are discussed.

physics.ins-det↗

arXiv2019

Design and Characterization of Superconducting Nanowire-Based Processors for Acceleration of Deep Neural Network Training

Training of deep neural networks (DNNs) is a computationally intensive task and requires massive volumes of data transfer. Performing these operations with the conventional von Neumann architectures creates unmanageable time and power costs. Recent studies have shown that mixed-signal designs involving crossbar architectures are capable of achieving acceleration factors as high as 30,000x over the state of the art digital processors. These approaches involve utilization of non-volatile memory (NVM) elements as local processors. However, no technology has been developed to-date that can satisfy the strict device requirements for the unit cell. This paper presents the superconducting nanowire-based processing element as a cross-point device. The unit cell has many programmable non-volatile states that can be used to perform analog multiplication. Importantly, these states are intrinsically discrete due to quantization of flux, which provides symmetric switching characteristics. Operation of these devices in a crossbar is described and verified with electro-thermal circuit simulations. Finally, validation of the concept in an actual DNN training task is shown using an emulator.

cs.ET↗

arXiv2019

Cryogenic Memory Architecture Integrating Spin Hall Effect based Magnetic Memory and Superconductive Cryotron Devices

One of the most challenging obstacles to realizing exascale computing is minimizing the energy consumption of L2 cache, main memory, and interconnects to that memory. For promising cryogenic computing schemes utilizing Josephson junction superconducting logic, this obstacle is exacerbated by the cryogenic system requirements that expose the technology's lack of high-density, high-speed and power-efficient memory. Here we demonstrate an array of cryogenic memory cells consisting of a non-volatile three-terminal magnetic tunnel junction element driven by the spin Hall effect, combined with a superconducting heater-cryotron bit-select element. The write energy of these memory elements is roughly 8 pJ with a bit-select element, designed to achieve a minimum overhead power consumption of about 30%. Individual magnetic memory cells measured at 4 K show reliable switching with write error rates below $10^{-6}$, and a 4x4 array can be fully addressed with bit select error rates of $10^{-6}$. This demonstration is a first step towards a full cryogenic memory architecture targeting energy and performance specifications appropriate for applications in superconducting high performance and quantum computing control systems, which require significant memory resources operating at 4 K.

physics.app-ph↗

arXiv2019

A Power Efficient Artificial Neuron Using Superconducting Nanowires

With the rising societal demand for more information-processing capacity with lower power consumption, alternative architectures inspired by the parallelism and robustness of the human brain have recently emerged as possible solutions. In particular, spiking neural networks (SNNs) offer a bio-realistic approach, relying on pulses analogous to action potentials as units of information. While software encoded networks provide flexibility and precision, they are often computationally expensive. As a result, hardware SNNs based on the spiking dynamics of a device or circuit represent an increasingly appealing direction. Here, we propose to use superconducting nanowires as a platform for the development of an artificial neuron. Building on an architecture first proposed for Josephson junctions, we rely on the intrinsic nonlinearity of two coupled nanowires to generate spiking behavior, and use electrothermal circuit simulations to demonstrate that the nanowire neuron reproduces multiple characteristics of biological neurons. Furthermore, by harnessing the nonlinearity of the superconducting nanowire's inductance, we develop a design for a variable inductive synapse capable of both excitatory and inhibitory control. We demonstrate that this synapse design supports direct fanout, a feature that has been difficult to achieve in other superconducting architectures, and that the nanowire neuron's nominal energy performance is competitive with that of current technologies.

q-bio.NC↗

arXiv2019

Source Shot Noise Mitigation in Focused Ion Beam Microscopy by Time-Resolved Measurement

Focused ion beam (FIB) microscopy suffers from source shot noise - random variation in the number of incident ions in any fixed dwell time - along with random variation in the number of detected secondary electrons per incident ion. This multiplicity of sources of randomness increases the variance of the measurements and thus worsens the trade-off between incident ion dose and image accuracy. Time-resolved sensing combined with maximum likelihood estimation from the resulting sets of measurements greatly reduces the effect of source shot noise. Through Fisher information analysis and Monte Carlo simulations, the reduction in mean-squared error or reduction in required dose is shown to be by a factor approximately equal to the secondary electron yield. Experiments with a helium ion microscope (HIM) are consistent with the analyses and suggest accuracy improvement for a fixed source dose, or reduced source dose for a desired imaging accuracy, by a factor of about 3.

cond-mat.mtrl-sci↗

arXiv2019

Detecting Dark Matter with Superconducting Nanowires

We propose the use of superconducting nanowires as both target and sensor for direct detection of sub-GeV dark matter. With excellent sensitivity to small energy deposits on electrons, and demonstrated low dark counts, such devices could be used to probe electron recoils from dark matter scattering and absorption processes. We demonstrate the feasibility of this idea using measurements of an existing fabricated tungsten-silicide nanowire prototype with 0.8 eV energy threshold and 4.3 nanograms with 10 thousand seconds of exposure, which showed no dark counts. The results from this device already place meaningful bounds on dark matter-electron interactions, including the strongest terrestrial bounds on sub-eV dark photon absorption to date. Future expected fabrication on larger scales and with lower thresholds should enable probing new territory in the direct detection landscape, establishing the complementarity of this approach to other existing proposals.

hep-ph↗

arXiv2019

Reduced damage in electron microscopy by using interaction-free measurement and conditional re-illumination

Interaction-free measurement (IFM) has been proposed as a means of high-resolution, low-damage imaging of radiation-sensitive samples, such as biomolecules and proteins. The basic setup for IFM is a Mach-Zehnder interferometer, and recent progress in nanofabricated electron diffraction gratings has made it possible to incorporate a Mach-Zehnder interferometer in a transmission-electron microscope (TEM). Therefore, the limits of performance of IFM with such an interferometer and a shot-noise limited electron source (such as that in a TEM) are of interest. In this work, we compared the error probability and sample damage for ideal IFM and classical imaging schemes, through theoretical analysis and numerical simulation. We considered a sample that is either completely transparent or completely opaque at each pixel. In our analysis, we also evaluated the impact of an additional detector for scattered electrons. The additional detector resulted in reduction of error by up to an order of magnitude, for both IFM and classical schemes. We also investigated a sample re-illumination scheme based on updating priors after each round of illumination and found that this scheme further reduced error by a factor of two. Implementation of these methods is likely achievable with existing instrumentation and would result in improved resolution in low-dose electron microscopy.

physics.ins-det↗

arXiv2019

A General Theoretical and Experimental Framework for Nanoscale Electromagnetism

Local, bulk response functions, e.g permittivity, and the macroscopic Maxwell equations completely specify the classical electromagnetic problem, which features only wavelength $λ$ and geometric scales. The above neglect of intrinsic electronic length scales $L_{\text{e}}$ leads to an eventual breakdown in the nanoscopic limit. Here, we present a general theoretical and experimental framework for treating nanoscale electromagnetic phenomena. The framework features surface-response functions---known as the Feibelman $d$-parameters---which reintroduce the missing electronic length scales. As a part of our framework, we establish an experimental procedure to measure these complex, dispersive surface response functions, enabled by quasi-normal-mode perturbation theory and observations of pronounced nonclassical effects---spectral shifts in excess of 30% and the breakdown of Kreibig-like broadening---in a quintessential multiscale architecture: film-coupled nanoresonators, with feature-sizes comparable to both $L_{\text{e}}$ and $λ$.

physics.optics↗

arXiv2018

Enhancement of optical response in nanowires by negative-tone PMMA lithography

The method of negative-tone-PMMA electron-beam lithography is investigated to improve the performance of nanowire-based superconducting detectors. Using this approach, the superconducting nanowire single-photon detectors (SNSPDs) have been fabricated from thick 5-nm NbN film sputtered at the room temperature. To investigate the impact of this process, SNSPDs were prepared by positive-tone and negative-tone-PMMA lithography, and their electrical and photodetection characteristics at 4.2 K were compared. The SNSPDs made by negative-tone-PMMA lithography show higher critical-current density and higher photon count rate at various wavelengths. Our results suggest a higher negative-tone-PMMA technology may be preferable to the standard positive-tone-PMMA lithography for this application.

physics.app-ph↗

arXiv2018

Superconducting nanowire single-photon detector with integrated impedance-matching taper

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, $I_\mathrm{B}\times Z_\mathrm{load}$, where $Z_\mathrm{load}$ is limited to 50 $Ω$ in standard r.f. electronics. Here, we break this limit by interfacing the 50 $Ω$ load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. It increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6$\times$ higher pulse amplitude, 3.7$\times$ faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.

physics.ins-det↗