arXiv subjects

Kento Kawaharazuka

Publications and source records attributed to Kento Kawaharazuka.

At least 19 recordsLinked to original sources

arXiv2026

LunaDrive: A Delay-Compensated High-Voltage GaN FET-Based Motor Driver for Dynamic Robots with Flat BLDC Motors

The performance improvement of high-power flat BLDC motors has accelerated the development of dynamic robots. However, many commercially available servo motors assume operating voltages of 48 V or lower, which limits the maximum rotational speed. Dynamic robots require rapid energy generation, so this voltage constraint restricts motion performance. Therefore, driving motors beyond the rated voltage is desirable to increase the instantaneous maximum speed. On the other hand, semiconductor devices used in motor drivers have a trade-off between voltage rating and current capacity. Conventional drivers using Si MOSFETs have difficulty achieving both high-voltage and high-current operation. Although GaN FETs are promising, compact drivers that can be mounted on the rear side of flat BLDC motors remain limited. In this study, a motor driver for high-power flat BLDC motors using GaN FETs is developed. The effect of delay compensation in the high-speed region beyond the rated operating range is also investigated. In the experiments, under 96 V operation, a continuous current of 30 A was achieved with a heat sink attached. A peak current of 80 A and a maximum electrical frequency of 3110 Hz were confirmed. A high-speed load lifting experiment driven by a LiPo battery 24S (100 V) was also conducted, demonstrating applicability to dynamic robot operation.

cs.RO↗

arXiv2026

Continuous Manifold-Decomposed Impedance Retargeting for Contact-Rich Imitation Learning

CMDIR extends Manifold-Decomposed Impedance Retargeting (MDIR) to transform fixed-impedance demonstrations into continuous variable-impedance controllers, which can also serve as structured supervision for imitation learning. Continuous Task-Manifold Impedance Representation (TMIR) pairs an evolving task frame with controller instructions. Demo-relative Compromise dynamics retain moving-basis transport and control/physical metric mismatch, yielding displacement, reaction-impulse, and perturbation-sensitivity criteria. Quality-to-Fast automatically compiles a solver structure from development paths within a predefined finite space, re-instantiates that structure for each demonstration, and certifies the resulting candidate by multi-resolution evaluation. Across 225 retargeted-controller trials in three real contact tasks, full CMDIR improves mean task-proxy retention and reduces mean pose deviation, force fluctuation, and peak force relative to discrete MDIR. FastMPO achieves a $5.8$--$9.4\times$ speedup over C-MPO with comparable closed-loop outcomes. Downstream experiments demonstrate learnability of the complete TMIR supervision interface; lower force fluctuation and peak force are observed among successful executions, while completion reliability remains uneven across tasks and environments.

cs.RO↗

arXiv2026

Design of a Biomimetic Joint-Covering Skin with Tissue-Like Structure to Enhance Proprioception in a Musculoskeletal Humanoid

Proprioception in musculoskeletal humanoids is typically estimated primarily from muscle sensing, while the role of cutaneous deformation around joints remains insufficiently explored. In biological systems, mechanoreceptors distributed within soft tissue complement muscle feedback and support reliable joint state estimation. This study presents the design of a biomimetic joint-covering skin with a tissue-like layered structure that integrates pressure- and stretch-sensitive elements within the joint-covering tissue. The proposed skin is implemented on the musculoskeletal humanoid Musashi-W, and its independent proprioceptive capability as well as its integration with muscle sensing are evaluated. Experimental results show that the proposed skin alone achieves joint angle estimation with an average error of approximately 3 degrees. Furthermore, integration with muscle sensing improves estimation accuracy. Owing to its joint-covering structure, the skin may mechanically mitigate the influence of external disturbances on the muscles, and the integration of multiple modalities suggests the possibility of contributing to the identification of external stimuli that are difficult to interpret using muscle sensing alone. This work presents a design methodology for biomimetic joint-covering skin and demonstrates that such tissue-structured skin can serve as an effective approach for extending proprioceptive systems in musculoskeletal humanoids.

cs.RO↗

arXiv2026

Robust Brachiation on a Life-Sized Dual-Arm Robot Using Waypoint-Guided Reinforcement Learning

Brachiation is a form of locomotion in which primates move primarily using their arms, enabling traversal in environments without footholds. However, this motion requires highly coordinated whole-body movement and precise timing control for bar grasping and release. As a result, achieving robust behavior on life-sized robotic platforms remains challenging. In this study, we present a reinforcement learning-based method to realize brachiation on a life-sized dual-arm robot. The core of the proposed approach is Waypoint-Guided Reinforcement Learning (WGRL), a learning framework for inducing non-linear and complex motions. For high-difficulty tasks where imitation learning data are unavailable, WGRL guides behavior acquisition by sparsely specifying waypoints for the end-effector trajectory, while whole-body motion is generated through reinforcement learning. In addition, by integrating the waypoint-following guidance with rewards based on task success and mechanical energy, and training in an environment designed for Sim-to-Real transfer, the proposed method achieves both forward progression and motion stability. The acquired behavior is evaluated through Sim-to-Sim experiments under monkey-bar environments with geometric variations and hardware experiments, confirming robust brachiation including failure recovery behavior. This study provides effective learning design guidelines for realizing arm-based locomotion on life-sized robotic hardware and expanding the traversable workspace of robots.

cs.RO↗

arXiv2026

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

cs.RO↗

arXiv2026

Neural Introspection Gating for Adaptive KV-Cache Reuse in Vision-Language-Action Models

Vision-Language-Action(VLA) models map camera images and language instructions directly to motor commands through a single autoregressive transformer. In real-time control, they still spend substantial compute recomputing key-value(KV) representations for visual tokens that barely change across neighboring frames. Recent work such as VLA-Cache reduces that cost by reusing KV states for visually static patches, but its policy relies only on observation-space heuristics and does not account for the model's own uncertainty. We propose Gated VLA-Cache, a lightweight, training-free extension that augments visual-similarity caching with neural introspection. The method monitors the logit margin between the top two predicted action tokens, a zero-cost confidence signal available during decoding. When the margin drops below a threshold, the cache is invalidated and a full recompute is triggered. Evaluated on four LIBERO benchmark suites with both OpenVLA and OpenVLA-OFT, Gated VLA-Cache improves reliability when blind caching hurts. On LIBERO-Goal and LIBERO-Long, it recovers over 100% of the lost accuracy while retaining 80% of the compute savings.

cs.RO↗

arXiv2026

MDIR: A Task-Manifold Impedance Retargeting Method for Contact-Rich Teleoperation

Fixed Cartesian impedance makes contact-rich teleoperation demonstrations practical, but gains that secure progress and contact support also determine impact and force variability. We study single-demonstration controller-to-controller impedance retargeting. Given one fixed Cartesian impedance command sequence {K0, D0, xcmd}, Manifold-Decomposed Impedance Retargeting (MDIR) deterministically reparameterizes the recorded controller into an executable task-channel variable-impedance command. MDIR targets this local retargeting problem by preserving projected task-channel responses near the demonstrated trajectory. It represents the source response in operational work, exertion, and support channels with a passive residual complement under a control-chain metric, computes an executable Cartesian-to-Manifold Retargeting (C2M) baseline, and applies Manifold-Constrained Parameter Optimization (MPO) to select a feasible representative with lower wrist-force peaks, impulse, force variability, and nominal controller power. Across planar wiping, pick-and-place, and pushing on a Franka Panda, the full MDIR controller passes Task Check in all 15 closed-loop executions and reduces all four aggressiveness metrics relative to the fixed-impedance demonstrations.

cs.RO↗

arXiv2026

TRACT: Temporally Routed Action Chunks with Chronological Phase Authority for Contact-Rich Manipulation

Action chunking shortens the effective decision horizon of robot imitation learning by predicting multiple future actions, while conventional phase conditioning describes the current control instant. When a predicted horizon crosses a procedural boundary, assigning the current phase to the entire chunk creates a structural temporal mismatch. We present TRACT, which factorizes phase-structured action chunking into an accepted current phase and a single CURRENT-to-NEXT boundary inside the future horizon. A task-local graph constrains chronological phase authority, and a cumulative boundary distribution monotonically routes future queries through phase-specific query and action paths. For contact execution, a causal response-deficit integrator compares policy intent with ACK-eligible subsequent motion, accumulates arm compensation when directional response is suppressed, and decays after confirmed recovery. Across six real-robot variants with ten trials each, full TRACT achieves 10/10 full-sequence success, 99.00 [88.75, 100.00]% median [min, max] wipe completion, zero observed phase ambiguity, and zero stalls. Under the current complete method package and evaluation setting, the routed representation obtains better observed task results than the flat package (6/10 vs. 3/10 success; 77.08% vs. 8.03% median wipe completion). Chronological authority reduces observed phase ambiguity from 8/10 to 0/10, and response integration reduces stalls from 4/10 to 0/10. The package comparison does not isolate routing from other generator-package differences.

cs.RO↗

arXiv2026

VLAff: Vision-Language-Affordance Model for Unified Actionable Affordances

Learning manipulation skills from human videos is promising for scalable robot learning. However, the embodiment mismatch between humans and robots makes this challenging. One promising solution is to learn object-centric actionable affordances that are embodiment-agnostic. In this work, we propose a framework that leverages egocentric human videos with state-of-the-art 3D Structure-from-Motion and hand mesh reconstruction to extract actionable affordances such as visual, grasp, and trajectory affordances that explicitly encode where to interact, how to grasp, and how to move. We construct EgoAffordance, a large-scale dataset comprising 204K episodes with 5.6M visual affordances and 11.6M grasp and trajectory affordances. Building on this, we introduce VLAff, a large vision-language model-based unified foundation model that learns cross-modal correlations across all actionable affordances. Given a visual observation and instruction, VLAff generates visual affordance heatmaps, grasp poses, and trajectories, which are then converted into directly executable actions by utilizing 3D scene information. Through extensive experiments, we demonstrate that VLAff not only achieves state-of-the-art performance on visual affordance prediction, but can also be effectively applied to real robot applications such as zero-shot manipulation and affordance-guided robot learning.

cs.RO↗

arXiv2026

Diffusion-Based Body Schema Learning Enabling Abnormal-State Adaptation in Musculoskeletal Robots

Musculoskeletal robots require an internal body schema that remains consistent under a wide range of physical state changes, including abnormalities such as muscle rupture and actuator jamming. Conventional approaches based on autoencoders or variational autoencoders learn average behaviors by projecting sensor and actuator signals into a low-dimensional latent space; however, exploration within the latent space alone has limited capability to handle out-of-distribution or abnormal states that are not included in the training data. To address this limitation, this study proposes a diffusion-based framework for body schema learning in musculoskeletal robots. Unlike generative models that operate through low-dimensional latent spaces, diffusion models can directly and iteratively estimate physically consistent sensor and actuator values in the high-dimensional space through a denoising process, even under partial observations and constraints, without requiring retraining. By formulating body schema adaptation as a gradient-guided denoising process, the proposed method enables adaptive estimation of appropriate muscle lengths and muscle tensions even under abnormal conditions such as muscle rupture and actuator jamming. The validity of the proposed framework is verified through simulation experiments using a musculoskeletal robot model.

cs.RO↗

arXiv2026

WARL: Wrench-Augmented Reinforcement Learning for Task-Agnostic Learning in Legged Robots

While reinforcement learning for legged robots has achieved high motor performance, it has been constrained by the limited exploration capability of actions confined to the joint space. To address this issue, this study proposes a new method, Wrench-Augmented Reinforcement Learning (WARL), which introduces a wrenche (force and torque) into the action space. The proposed method combines wrench-guided exploration with a success rate-based curriculum mechanism to expand exploration capabilities in the early stages of learning, with the ultimate goal of acquiring behaviors based solely on joint control. Experiments using a quadruped robot demonstrated that WARL can learn robustly across diverse terrains and motor tasks without requiring terrain-specific reward adjustments or complex curriculum designs. Furthermore, an ablation study verified the effectiveness of the Switching Curriculum, which gradually eliminates the wrench. On the other hand, we also show that introducing a wrench can encourage behaviors that do not sufficiently exploit the robot's physical embodiment. These findings suggest that while wrench-based exploration enhancement is effective for improving learning efficiency, designing it in a way that is consistent with the robot's physical structure is a critical future challenge.

cs.RO↗

arXiv2026

MEVION: Low-Cost Open-Source Data Collection System for Powerful and High-Speed Dual-Arm Manipulation

The global competition for developing robotic foundation models is intensifying. Among the data collection systems used for dual-arm robots, ALOHA is representative of being low-cost and open-source, and is widely adopted by researchers as a de facto standard. However, due to its limited ability to generate high forces and speeds, it is difficult to handle heavy objects or perform fast manipulations. To address this, we developed MEVION, a low-cost and open-source dual-arm robot data collection system capable of generating greater force and speed. All parts of this robot can be sourced through e-commerce, and by extensively utilizing sheet metal welding, its large body structure is constructed with a small number of components at low cost, while also simplifying assembly. MEVION is equipped with four 6-DoF arms with parallel grippers. Each arm weighs 7.0 kg and has a maximum torque of 60 Nm, and the entire system can be constructed for about USD 14,000. The elbow joint adopts a closed-link mechanism similar to those used in quadruped robots, which reduces the distal mass and enables higher force and speed output at the end-effector. We demonstrate that MEVION enables data collection for object manipulation tasks not previously possible and supports imitation learning-based motion generation. All hardware and software of this work are included in the Supplementary Materials or https://github.com/haraduka/mevion.

cs.RO↗

arXiv2026

WiXus: A Wheeled-Legged Robot with Wire-Driven Environmental Utilizing to Integrate Mobility and Manipulation

Wheeled-legged robots, which have wheels at their feet and achieve high mobility by coordinating wheel drive and leg drive, have been developed. These robots have been developed purely as platforms specialized for locomotion. Therefore, they do not have a means to repurpose their legs for roles other than locomotion, such as object manipulation or tool utilization. In this paper, we address the problem of how to draw out the potential task-execution capability of the legs by freeing them from the roles of locomotion through external body support. To this end, we propose and develop a new robot, WiXus, which fuses a wheeled-legged mechanism with a wire-driven mechanism that utilizes the external environment. The developed WiXus demonstrates not only planar locomotion with wheeled-legged drive, but also three-dimensional mobility such as cliff climbing by coordinating wire-driven and wheeled-legged actuation. Furthermore, by suspending the body with wire-driven actuation, WiXus successfully repurpose its legs as arms to perform object manipulation, (e.g., rescuing a dog (stuffed animal)), and tool utilization (e.g., harvesting an apple (mockup) with loppers). This study demonstrates that the approach of utilizing the environment with wire-driven actuation is a new design principle that extends the operational domain of wheeled-legged robots.

cs.RO↗

arXiv2026

EFGCL: Learning Dynamic Motion through Spotting-Inspired External Force Guided Curriculum Learning

Learning dynamic whole-body motions for legged robots through reinforcement learning (RL) remains challenging due to the high risk of failure, which makes efficient exploration difficult and often leads to unstable learning. In this paper, we propose External Force Guided Curriculum Learning (EFGCL), a guided RL approach based on the principle of physical guidance, in which external assistive forces are introduced during training. Inspired by spotting in artistic gymnastics, EFGCL enables agents to physically experience successful motion executions without relying on task-specific reward shaping or reference trajectories. Experiments on a quadrupedal robot performing Jump, Backflip, and Lateral-Flip tasks demonstrate that EFGCL accelerates learning of the Jump task by approximately a factor of two and enables the acquisition of complex whole body motions that conventional RL methods fail to learn. We further show that the learned policies can be deployed on real robot, reproducing motions consistent with those observed in simulation. These results indicate that physically guided exploration, which allows agents to experience success early in training, is an effective and general strategy for improving learning efficiency in dynamic whole-body motion tasks.

cs.RO↗

arXiv2026

Exploring the proprioceptive potential of joint receptors using a biomimetic robotic joint

In neuroscience, joint receptors have traditionally been viewed as limit detectors, providing positional information only at extreme joint angles, while muscle spindles are considered the primary sensors of joint angle position. However, joint receptors are widely distributed throughout the joint capsule, and their full role in proprioception remains unclear. In this study, we specifically focused on mimicking Type I joint receptors, which respond to slow and sustained movements, and quantified their proprioceptive potential using a biomimetic joint developed with robotics technology. Results showed that Type I-like joint receptors alone enabled proprioceptive sensing with an average error of less than 2 degrees in both bending and twisting motions. These findings suggest that joint receptors may play a greater role in proprioception than previously recognized and that the relative contributions of muscle spindles and joint receptors are differentially weighted within neural networks during development and evolution. Furthermore, this work may prompt new discussions on the differential proprioceptive deficits observed between the elbows and knees in patients with hereditary sensory and autonomic neuropathy type III. Together, these findings highlight the potential of biomimetics-based robotic approaches for advancing interdisciplinary research bridging neuroscience, medicine, and robotics.

cs.RO↗

arXiv2026

MEVIUS2: Practical Open-Source Quadruped Robot with Sheet Metal Welding and Multimodal Perception

Various quadruped robots have been developed to date, and thanks to reinforcement learning, they are now capable of traversing diverse types of rough terrain. In parallel, there is a growing trend of releasing these robot designs as open-source, enabling researchers to freely build and modify robots themselves. However, most existing open-source quadruped robots have been designed with 3D printing in mind, resulting in structurally fragile systems that do not scale well in size, leading to the construction of relatively small robots. Although a few open-source quadruped robots constructed with metal components exist, they still tend to be small in size and lack multimodal sensors for perception, making them less practical. In this study, we developed MEVIUS2, an open-source quadruped robot with a size comparable to Boston Dynamics' Spot, whose structural components can all be ordered through e-commerce services. By leveraging sheet metal welding and metal machining, we achieved a large, highly durable body structure while reducing the number of individual parts. Furthermore, by integrating sensors such as LiDARs and a high dynamic range camera, the robot is capable of detailed perception of its surroundings, making it more practical than previous open-source quadruped robots. We experimentally validated that MEVIUS2 can traverse various types of rough terrain and demonstrated its environmental perception capabilities. All hardware, software, and training environments can be obtained from Supplementary Materials or https://github.com/haraduka/mevius2.

cs.RO↗

arXiv2026

Dexterous grasp data augmentation based on grasp synthesis with fingertip workspace cloud and contact-aware sampling

Robotic grasping is a fundamental yet crucial component of robotic applications, as effective grasping often serves as the starting point for various tasks. With the rapid advancement of neural networks, data-driven approaches for robotic grasping have become mainstream. However, efficiently generating grasp datasets for training remains a bottleneck. This is compounded by the diverse structures of robotic hands, making the design of generalizable grasp generation methods even more complex. In this work, we propose a teleoperation-based framework to collect a small set of grasp pose demonstrations, which are augmented using FSG--a Fingertip-contact-aware Sampling-based Grasp generator. Based on the demonstrated grasp poses, we propose AutoWS, which automatically generates structured workspace clouds of robotic fingertips, embedding the hand structure information directly into the clouds to eliminate the need for inverse kinematics calculations. Experiments on grasping the YCB objects show that our method significantly outperforms existing approaches in both speed and valid pose generation rate. Our framework enables real-time grasp generation for hands with arbitrary structures and produces human-like grasps when combined with demonstrations, providing an efficient and robust data augmentation tool for data-driven grasp training.

cs.RO↗

arXiv2026

Efficient Robot Design with Multi-Objective Black-Box Optimization and Large Language Models

Various methods for robot design optimization have been developed so far. These methods are diverse, ranging from numerical optimization to black-box optimization. While numerical optimization is fast, it is not suitable for cases involving complex structures or discrete values, leading to frequent use of black-box optimization instead. However, black-box optimization suffers from low sampling efficiency and takes considerable sampling iterations to obtain good solutions. In this study, we propose a method to enhance the efficiency of robot body design based on black-box optimization by utilizing large language models (LLMs). In parallel with the sampling process based on black-box optimization, sampling is performed using LLMs, which are provided with problem settings and extensive feedback. We demonstrate that this method enables more efficient exploration of design solutions and discuss its characteristics and limitations.

cs.RO↗