arXiv subjects

L. Lautner

Publications and source records attributed to L. Lautner.

8 recordsLinked to original sources

arXiv2026

Large-scale real-time signal processing in physics experiments: The ALICE TPC FPGA pipeline

For LHC Run 3, the ALICE Time Projection Chamber was upgraded to operate in continuous readout mode. Interaction rates of up to 50 kHz in Pb-Pb collisions require real-time processing of more than 3 TB/s of raw detector data. This requirement is met by a custom FPGA-based processing pipeline that performs the complete front-end data treatment fully in-stream, including common-mode correction, pedestal subtraction, ion-tail filtering, zero suppression, and dense data packing. A central element of the design is a highly parallel common-mode correction algorithm operating directly on the streaming data. It robustly identifies signal-free readout channels on a time-bin basis and applies pad-dependent scaling to compensate for local variations in capacitive coupling in the GEM readout. In combination with pedestal subtraction and ion-tail filtering, this enables accurate baseline restoration under extreme high-occupancy conditions, preventing signal loss while efficiently suppressing noise prior to zero suppression. The pipeline operates continuously at the full detector bandwidth and reduces the raw input rate to about 900 GB/s for Pb-Pb collisions at the target interaction rate. Overall, it represents a large-scale FPGA-based real-time signal-processing implementation for high-energy physics detector readout.

physics.ins-det↗

arXiv2023

Impact of the gas choice and the geometry on the breakdown limits in Micromegas detectors

In this study we investigate the stability limits of Micromegas detectors upon irradiation with alpha particles. The results are obtained with meshes with different optical transparency and geometry of wires. The measurements are performed in Ar- and Ne- based mixtures with different CO$_2$ content. We observe that the breakdown limit strongly depends on the gas and that a higher amount of quencher in the mixture does not necessarily correlate with higher stability. In addition, we observe discharge probability scaling with the wire pitch. This suggests that a Micromegas mesh cell can be treated as an independent amplification unit, similar to a hole in a GEM foil. The outcome of these studies provides valuable input for further optimization of MPGD detectors, multi-layer stacks in particular.

physics.ins-det↗

arXiv2022

The MAPS foil

We present a method of embedding a Monolithic Active Pixel Sensor (MAPS) into a flexible printed circuit board (FPC) and its interconnection by means of through-hole copper plating. The resulting assembly, baptised "MAPS foil", is a flexible, light, protected, and fully integrated detector module. By using widely available printed circuit board manufacturing techniques, the production of these devices can be scaled easily in size and volume, making it a compelling candidate for future large-scale applications. A first series of prototypes that embed the ALPIDE chip has been produced, functionally tested, and shown to be working.

physics.ins-det↗

arXiv2022

Systematic investigation of critical charge limits in Thick GEMs

We present discharge probability studies performed with a single Thick Gas Electron Multiplier (THGEM) irradiated with alpha particles in Ar-CO$_2$ and Ne-CO$_2$ mixtures. We observe a clear dependency of the discharge stability on the noble gas and quencher content pointing to lighter gases being more stable against the development of streamer discharges. A detailed comparison of the measurements with Geant4 simulations allowed us to extract the critical charge value leading to the formation of a spark in a THGEM hole, which is found to be within the range of 3-7$\times10^6$ electrons, depending on the gas mixture. Our experimental findings are compared to previous GEM results. We show that the discharge probability of THGEMs exceeds the one measured with GEMs by orders of magnitude. This can be explained with simple geometrical considerations, where primary ionization is collected by a lower number of holes available in a THGEM structure, reaching higher primary charge densities and thus increasing the probability of a spark occurrence. However, we show that the critical charge limits are similar for both amplification structures.

physics.plasm-ph↗

arXiv2021

New (TH)GEM coating materials characterised using spectroscopy methods

In this work GEM and single-hole Thick GEM structures, composed of different coating materials, are studied. The used foils incorporate conductive layers made of copper, aluminium, molybdenum, stainless steel, tungsten and tantalum. The main focus of the study is the determination of the material dependence of the formation of electrical discharges in GEM-based detectors. For this task, discharge probability measurements are conducted with several Thick GEM samples using a basic electronics readout chain. In addition to that, optical spectroscopy methods are employed to study the light emitted during discharges from the different foils. It is observed that the light spectra of GEMs include emission lines from the conductive layer material. This indicates the presence of the foil material in the discharge plasma after the initial spark. However, no lines associated with the coating material are observed while studying spark discharges induced in Thick GEMs. It is concluded that the conductive layer material does not play a substantial role in terms of stability against primary discharges. However, a strong material dependence is observed in the case of secondary discharge formation, pointing to molybdenum coating as the one providing increased stability.

physics.ins-det↗

arXiv2019

High voltage scheme optimization for secondary discharge mitigation in GEM-based detectors

We investigate the influence of the high voltage scheme elements on the stability of a detector based on a single $10\times10$ cm$^2$ area GEM with respect to the secondary discharge occurrence. These violent events pose a major threat to the integrity of GEM detectors and their Front-End Electronics and need to be avoided by any means. For a single GEM setup, we propose a detailed high voltage scheme that is designed to prevent secondary discharges. We determine optimal values of the protection resistors and parasitic capacitances introduced by cables used in the system. The results of this paper may be used as a guideline for the optimization of more complicated multi-GEM detectors.

physics.ins-det↗

arXiv2019

Secondary discharge studies in single and multi GEM structures

Secondary discharges, which consist of the breakdown of a gap near a GEM foil upon a primary discharge across that GEM, are studied in this work. Their main characteristics are the occurrence a few $10\,\mu \textrm{s}$ after the primary, the relatively sharp onset at moderate electric fields across the gap, the absence of increased fields in the system, and their occurrence under both field directions. They can be mitigated using series resistors in the high-voltage connection to the GEM electrode facing towards an anode. The electric field at which the onset of secondary discharges occurs indeed increases with increasing resistance. Discharge propagation form GEM to GEM in a multi-GEM system affects the occurrence probability of secondary discharges in the gaps between neighbouring GEMs. Furthermore, evidence of charges flowing through the gap after the primary discharge are reported. Such currents may or may not lead to a secondary discharge. A characteristic charge, of the order of $10^{10}\,\textrm{electrons}$, has been measured as the threshold for a primary discharge to be followed by a secondary discharge, and this number slightly depends on the gas composition. A mechanism involving the heating of the cathode surface as trigger for secondary discharges is proposed.

physics.ins-det↗

arXiv2018

Particle identification studies with a full-size 4-GEM prototype for the ALICE TPC upgrade

A large Time Projection Chamber is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019/20, the LHC will deliver Pb beams colliding at an interaction rate of about 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. This will result in a significant improvement on the sensitivity to rare probes that are considered key observables to characterize the QCD matter created in such collisions. In order to make full use of this luminosity, the currently used gated Multi-Wire Proportional Chambers will be replaced. The upgrade relies on continuously operated readout detectors employing Gas Electron Multiplier technology to retain the performance in terms of particle identification via the measurement of the specific energy loss by ionization d$E$/d$x$. A full-size readout chamber prototype was assembled in 2014 featuring a stack of four GEM foils as an amplification stage. The performance of the prototype was evaluated in a test beam campaign at the CERN PS. The d$E$/d$x$ resolution complies with both the performance of the currently operated MWPC-based readout chambers and the challenging requirements of the ALICE TPC upgrade program. Detailed simulations of the readout system are able to reproduce the data.

physics.ins-det↗