arXiv subjects

Masayuki Inaba

Publications and source records attributed to Masayuki Inaba.

At least 73 records · Page 4Linked to original sources

arXiv2024

Self-Supervised Learning of Visual Servoing for Low-Rigidity Robots Considering Temporal Body Changes

In this study, we investigate object grasping by visual servoing in a low-rigidity robot. It is difficult for a low-rigidity robot to handle its own body as intended compared to a rigid robot, and calibration between vision and body takes some time. In addition, the robot must constantly adapt to changes in its body, such as the change in camera position and change in joints due to aging. Therefore, we develop a method for a low-rigidity robot to autonomously learn visual servoing of its body. We also develop a mechanism that can adaptively change its visual servoing according to temporal body changes. We apply our method to a low-rigidity 6-axis arm, MyCobot, and confirm its effectiveness by conducting object grasping experiments based on visual servoing.

cs.RO↗

arXiv2024

Design, Control, and Motion-Planning for a Root-Perching Rotor-Distributed Manipulator

Manipulation performance improvement is crucial for aerial robots. For aerial manipulators, the baselink position and attitude errors directly affect the precision at the end effector. To address this stability problem, fixed-body approaches such as perching on the environment using the rotor suction force are useful. Additionally, conventional arm-equipped multirotors, called rotor-concentrated manipulators (RCMs), find it difficult to generate a large wrench at the end effector due to joint torque limitations. Using distributed rotors to each link, the thrust can support each link weight, decreasing the arm joints' torque. Based on this approach, rotor-distributed manipulators (RDMs) can increase feasible wrench and reachability of the end-effector. This paper introduces a minimal configuration of a rotor-distributed manipulator that can perch on surfaces, especially ceilings, using a part of their body. First, we design a minimal rotor-distributed arm considering the flight and end-effector performance. Second, a flight controller is proposed for this minimal RDM along with a perching controller adaptable for various types of aerial robots. Third, we propose a motion planning method based on inverse kinematics (IK), considering specific constraints to the proposed RDMs such as perching force. Finally, we evaluate flight and perching motions and \revise{confirm} that the proposed manipulator can significantly improve the manipulation performance.

eess.SY↗

arXiv2024

Adaptive Whole-body Robotic Tool-use Learning on Low-rigidity Plastic-made Humanoids Using Vision and Tactile Sensors

Various robots have been developed so far; however, we face challenges in modeling the low-rigidity bodies of some robots. In particular, the deflection of the body changes during tool-use due to object grasping, resulting in significant shifts in the tool-tip position and the body's center of gravity. Moreover, this deflection varies depending on the weight and length of the tool, making these models exceptionally complex. However, there is currently no control or learning method that takes all of these effects into account. In this study, we propose a method for constructing a neural network that describes the mutual relationship among joint angle, visual information, and tactile information from the feet. We aim to train this network using the actual robot data and utilize it for tool-tip control. Additionally, we employ Parametric Bias to capture changes in this mutual relationship caused by variations in the weight and length of tools, enabling us to understand the characteristics of the grasped tool from the current sensor information. We apply this approach to the whole-body tool-use on KXR, a low-rigidity plastic-made humanoid robot, to validate its effectiveness.

cs.RO↗

arXiv2024

Robotic Constrained Imitation Learning for the Peg Transfer Task in Fundamentals of Laparoscopic Surgery

In this study, we present an implementation strategy for a robot that performs peg transfer tasks in Fundamentals of Laparoscopic Surgery (FLS) via imitation learning, aimed at the development of an autonomous robot for laparoscopic surgery. Robotic laparoscopic surgery presents two main challenges: (1) the need to manipulate forceps using ports established on the body surface as fulcrums, and (2) difficulty in perceiving depth information when working with a monocular camera that displays its images on a monitor. Especially, regarding issue (2), most prior research has assumed the availability of depth images or models of a target to be operated on. Therefore, in this study, we achieve more accurate imitation learning with only monocular images by extracting motion constraints from one exemplary motion of skilled operators, collecting data based on these constraints, and conducting imitation learning based on the collected data. We implemented an overall system using two Franka Emika Panda Robot Arms and validated its effectiveness.

cs.RO↗

arXiv2024

Deep Predictive Model Learning with Parametric Bias: Handling Modeling Difficulties and Temporal Model Changes

When a robot executes a task, it is necessary to model the relationship among its body, target objects, tools, and environment, and to control its body to realize the target state. However, it is difficult to model them using classical methods if the relationship is complex. In addition, when the relationship changes with time, it is necessary to deal with the temporal changes of the model. In this study, we have developed Deep Predictive Model with Parametric Bias (DPMPB) as a more human-like adaptive intelligence to deal with these modeling difficulties and temporal model changes. We categorize and summarize the theory of DPMPB and various task experiments on the actual robots, and discuss the effectiveness of DPMPB.

cs.RO↗

arXiv2024

HumanMimic: Learning Natural Locomotion and Transitions for Humanoid Robot via Wasserstein Adversarial Imitation

Transferring human motion skills to humanoid robots remains a significant challenge. In this study, we introduce a Wasserstein adversarial imitation learning system, allowing humanoid robots to replicate natural whole-body locomotion patterns and execute seamless transitions by mimicking human motions. First, we present a unified primitive-skeleton motion retargeting to mitigate morphological differences between arbitrary human demonstrators and humanoid robots. An adversarial critic component is integrated with Reinforcement Learning (RL) to guide the control policy to produce behaviors aligned with the data distribution of mixed reference motions. Additionally, we employ a specific Integral Probabilistic Metric (IPM), namely the Wasserstein-1 distance with a novel soft boundary constraint to stabilize the training process and prevent mode collapse. Our system is evaluated on a full-sized humanoid JAXON in the simulator. The resulting control policy demonstrates a wide range of locomotion patterns, including standing, push-recovery, squat walking, human-like straight-leg walking, and dynamic running. Notably, even in the absence of transition motions in the demonstration dataset, robots showcase an emerging ability to transit naturally between distinct locomotion patterns as desired speed changes.

cs.RO↗

arXiv2024

TWIMP: Two-Wheel Inverted Musculoskeletal Pendulum as a Learning Control Platform in the Real World with Environmental Physical Contact

By the recent spread of machine learning in the robotics field, a humanoid that can act, perceive, and learn in the real world through contact with the environment needs to be developed. In this study, as one of the choices, we propose a novel humanoid TWIMP, which combines a human mimetic musculoskeletal upper limb with a two-wheel inverted pendulum. By combining the benefit of a musculoskeletal humanoid, which can achieve soft contact with the external environment, and the benefit of a two-wheel inverted pendulum with a small footprint and high mobility, we can easily investigate learning control systems in environments with contact and sudden impact. We reveal our whole concept and system details of TWIMP, and execute several preliminary experiments to show its potential ability.

cs.RO↗

arXiv2024

A Method of Joint Angle Estimation Using Only Relative Changes in Muscle Lengths for Tendon-driven Humanoids with Complex Musculoskeletal Structures

Tendon-driven musculoskeletal humanoids typically have complex structures similar to those of human beings, such as ball joints and the scapula, in which encoders cannot be installed. Therefore, joint angles cannot be directly obtained and need to be estimated using the changes in muscle lengths. In previous studies, methods using table-search and extended kalman filter have been developed. These methods express the joint-muscle mapping, which is the nonlinear relationship between joint angles and muscle lengths, by using a data table, polynomials, or a neural network. However, due to computational complexity, these methods cannot consider the effects of polyarticular muscles. In this study, considering the limitation of the computational cost, we reduce unnecessary degrees of freedom, divide joints and muscles into several groups, and formulate a joint angle estimation method that takes into account polyarticular muscles. Also, we extend the estimation method to propose a joint angle estimation method using only the relative changes in muscle lengths. By this extension, which does not use absolute muscle lengths, we do not need to execute a difficult calibration of muscle lengths for tendon-driven musculoskeletal humanoids. Finally, we conduct experiments in simulation and actual environments, and verify the effectiveness of this study.

cs.RO↗

arXiv2024

Designing Fluid-Exuding Cartilage for Biomimetic Robots Mimicking Human Joint Lubrication Function

The human joint is an open-type joint composed of bones, cartilage, ligaments, synovial fluid, and joint capsule, having advantages of flexibility and impact resistance. However, replicating this structure in robots introduces friction challenges due to the absence of bearings. To address this, our study focuses on mimicking the fluid-exuding function of human cartilage. We employ a rubber-based 3D printing technique combined with absorbent materials to create a versatile and easily designed cartilage sheet for biomimetic robots. We evaluate both the fluid-exuding function and friction coefficient of the fabricated flat cartilage sheet. Furthermore, we practically create a piece of curved cartilage and an open-type biomimetic ball joint in combination with bones, ligaments, synovial fluid, and joint capsule to demonstrate the utility of the proposed cartilage sheet in the construction of such joints.

cs.RO↗

arXiv2024

Body Design and Gait Generation of Chair-Type Asymmetrical Tripedal Low-rigidity Robot

In this study, a chair-type asymmetric tripedal low-rigidity robot was designed based on the three-legged chair character in the movie "Suzume" and its gait was generated. Its body structure consists of three legs that are asymmetric to the body, so it cannot be easily balanced. In addition, the actuator is a servo motor that can only feed-forward rotational angle commands and the sensor can only sense the robot's posture quaternion. In such an asymmetric and imperfect body structure, we analyzed how gait is generated in walking and stand-up motions by generating gaits with two different methods: a method using linear completion to connect the postures necessary for the gait discovered through trial and error using the actual robot, and a method using the gait generated by reinforcement learning in the simulator and reflecting it to the actual robot. Both methods were able to generate gait that realized walking and stand-up motions, and interesting gait patterns were observed, which differed depending on the method, and were confirmed on the actual robot. Our code and demonstration videos are available here: https://github.com/shin0805/Chair-TypeAsymmetricalTripedalRobot.git

cs.RO↗

arXiv2024

Online Self-body Image Acquisition Considering Changes in Muscle Routes Caused by Softness of Body Tissue for Tendon-driven Musculoskeletal Humanoids

Tendon-driven musculoskeletal humanoids have many benefits in terms of the flexible spine, multiple degrees of freedom, and variable stiffness. At the same time, because of its body complexity, there are problems in controllability. First, due to the large difference between the actual robot and its geometric model, it cannot move as intended and large internal muscle tension may emerge. Second, movements which do not appear as changes in muscle lengths may emerge, because of the muscle route changes caused by softness of body tissue. To solve these problems, we construct two models: ideal joint-muscle model and muscle-route change model, using a neural network. We initialize these models by a man-made geometric model and update them online using the sensor information of the actual robot. We validate that the tendon-driven musculoskeletal humanoid Kengoro is able to obtain a correct self-body image through several experiments.

cs.RO↗

arXiv2024

Online Learning of Joint-Muscle Mapping Using Vision in Tendon-driven Musculoskeletal Humanoids

The body structures of tendon-driven musculoskeletal humanoids are complex, and accurate modeling is difficult, because they are made by imitating the body structures of human beings. For this reason, we have not been able to move them accurately like ordinary humanoids driven by actuators in each axis, and large internal muscle tension and slack of tendon wires have emerged by the model error between its geometric model and the actual robot. Therefore, we construct a joint-muscle mapping (JMM) using a neural network (NN), which expresses a nonlinear relationship between joint angles and muscle lengths, and aim to move tendon-driven musculoskeletal humanoids accurately by updating the JMM online from data of the actual robot. In this study, the JMM is updated online by using the vision of the robot so that it moves to the correct position (Vision Updater). Also, we execute another update to modify muscle antagonisms correctly (Antagonism Updater). By using these two updaters, the error between the target and actual joint angles decrease to about 40% in 5 minutes, and we show through a manipulation experiment that the tendon-driven musculoskeletal humanoid Kengoro becomes able to move as intended. This novel system can adapt to the state change and growth of robots, because it updates the JMM online successively.

cs.RO↗

arXiv2024

Long-time Self-body Image Acquisition and its Application to the Control of Musculoskeletal Structures

The tendon-driven musculoskeletal humanoid has many benefits that human beings have, but the modeling of its complex muscle and bone structures is difficult and conventional model-based controls cannot realize intended movements. Therefore, a learning control mechanism that acquires nonlinear relationships between joint angles, muscle tensions, and muscle lengths from the actual robot is necessary. In this study, we propose a system which runs the learning control mechanism for a long time to keep the self-body image of the musculoskeletal humanoid correct at all times. Also, we show that the musculoskeletal humanoid can conduct position control, torque control, and variable stiffness control using this self-body image. We conduct a long-time self-body image acquisition experiment lasting 3 hours, evaluate variable stiffness control using the self-body image, etc., and discuss the superiority and practicality of the self-body image acquisition of musculoskeletal structures, comprehensively.

cs.RO↗

arXiv2024

Development of Musculoskeletal Legs with Planar Interskeletal Structures to Realize Human Comparable Moving Function

Musculoskeletal humanoids have been developed by imitating humans and expected to perform natural and dynamic motions as well as humans. To achieve desired motions stably in current musculoskeletal humanoids is not easy because they cannot maintain the sufficient moment arm of muscles in various postures. In this research, we discuss planar structures that spread across joint structures such as ligament and planar muscles and the application of planar interskeletal structures to humanoid robots. Next, we develop MusashiOLegs, a musculoskeletal legs which has planar interskeletal structures and conducts several experiments to verify the importance of planar interskeletal structures.

cs.RO↗

arXiv2024

Realization of Seated Walk by a Musculoskeletal Humanoid with Buttock-Contact Sensors From Human Constrained Teaching

In this study, seated walk, a movement of walking while sitting on a chair with casters, is realized on a musculoskeletal humanoid from human teaching. The body is balanced by using buttock-contact sensors implemented on the planar interskeletal structure of the human mimetic musculoskeletal robot. Also, we develop a constrained teaching method in which one-dimensional control command, its transition, and a transition condition are described for each state in advance, and a threshold value for each transition condition such as joint angles and foot contact sensor values is determined based on human teaching. Complex behaviors can be easily generated from simple inputs. In the musculoskeletal humanoid MusashiOLegs, forward, backward, and rotational movements of seated walk are realized.

cs.RO↗

arXiv2024

High-Power, Flexible, Robust Hand: Development of Musculoskeletal Hand Using Machined Springs and Realization of Self-Weight Supporting Motion with Humanoid

Human can not only support their body during standing or walking, but also support them by hand, so that they can dangle a bar and others. But most humanoid robots support their body only in the foot and they use their hand just to manipulate objects because their hands are too weak to support their body. Strong hands are supposed to enable humanoid robots to act in much broader scene. Therefore, we developed new life-size five-fingered hand that can support the body of life-size humanoid robot. It is tendon-driven and underactuated hand and actuators in forearms produce large gripping force. This hand has flexible joints using machined springs, which can be designed integrally with the attachment. Thus, it has both structural strength and impact resistance in spite of small size. As other characteristics, this hand has force sensors to measure external force and the fingers can be flexed along objects though the number of actuators to flex fingers is less than that of fingers. We installed the developed hand on musculoskeletal humanoid "Kengoro" and achieved two self-weight supporting motions: push-up motion and dangling motion.

cs.RO↗

arXiv2024

Five-fingered Hand with Wide Range of Thumb Using Combination of Machined Springs and Variable Stiffness Joints

Human hands can not only grasp objects of various shape and size and manipulate them in hands but also exert such a large gripping force that they can support the body in the situations such as dangling a bar and climbing a ladder. On the other hand, it is difficult for most robot hands to manage both. Therefore in this paper we developed the hand which can grasp various objects and exert large gripping force. To develop such hand, we focused on the thumb CM joint with wide range of motion and the MP joints of four fingers with the DOF of abduction and adduction. Based on the hand with large gripping force and flexibility using machined spring, we applied above mentioned joint mechanism to the hand. The thumb CM joint has wide range of motion because of the combination of three machined springs and MP joints of four fingers have variable rigidity mechanism instead of driving each joint independently in order to move joint in limited space and by limited actuators. Using the developed hand, we achieved the grasping of various objects, supporting a large load and several motions with an arm.

cs.RO↗

arXiv2024

Learning-Based Wiping Behavior of Low-Rigidity Robots Considering Various Surface Materials and Task Definitions

Wiping behavior is a task of tracing the surface of an object while feeling the force with the palm of the hand. It is necessary to adjust the force and posture appropriately considering the various contact conditions felt by the hand. Several studies have been conducted on the wiping motion, however, these studies have only dealt with a single surface material, and have only considered the application of the amount of appropriate force, lacking intelligent movements to ensure that the force is applied either evenly to the entire surface or to a certain area. Depending on the surface material, the hand posture and pressing force should be varied appropriately, and this is highly dependent on the definition of the task. Also, most of the movements are executed by high-rigidity robots that are easy to model, and few movements are executed by robots that are low-rigidity but therefore have a small risk of damage due to excessive contact. So, in this study, we develop a method of motion generation based on the learned prediction of contact force during the wiping motion of a low-rigidity robot. We show that MyCobot, which is made of low-rigidity resin, can appropriately perform wiping behaviors on a plane with multiple surface materials based on various task definitions.

cs.RO↗