arXiv subjects

Mikhail Churaev

Publications and source records attributed to Mikhail Churaev.

12 recordsLinked to original sources

arXiv2024

An ultra-broadband photonic-chip-based traveling-wave parametric amplifier

Optical amplification, crucial for modern communication and data center interconnects, primarily relies on erbium-doped fiber amplifiers (EDFAs) to enhance signals without distortion. While EDFAs were historically decisive for the introduction of dense wavelength-division multiplexing, they only cover a portion of the low-loss spectrum of optical fibers. Pioneering work on optical traveling-wave parametric amplifiers (TWPAs) utilizing intrinsic third-order optical nonlinearity has led to demonstrations of increased channel capacity and performance. TWPAs are unidirectional, offer high gain, and can reach the 3-dB quantum limit for phase-preserving amplifiers. Despite the use of highly nonlinear fibers or bulk waveguides, their power requirements and technical complexity have impeded adoption. In contrast, TWPAs based on photonic integrated circuits (PICs) offer the advantages of substantially increased mode confinement and optical nonlinearity but have been limited in bandwidth because of the trade-off with maintaining low propagation loss. We overcome this challenge by using low-loss gallium phosphide-on-silicon dioxide PICs and attain up to 35~dB of parametric gain with waveguides only a few centimeters long in a compact footprint of 0.25 square millimeters. Fiber-to-fiber net gain exceeding 10 dB across a bandwidth of approximately 140 nm is achieved, surpassing the gain window of a standard C-band EDFA. We furthermore demonstrate the capability to handle weak signals; input powers can range over six orders of magnitude while maintaining a low noise figure. We exploit these performance characteristics to amplify both optical frequency combs and coherent communication signals. This marks the first ultra-broadband, high-gain, continuous-wave amplification in a PIC, opening up new capabilities for next-generation optical communication, metrology, and sensing.

physics.optics↗

arXiv2024

Ultrabroadband thin-film lithium tantalate modulator for high-speed communications

The continuous growth of global data traffic over the past three decades, along with advances in disaggregated computing architectures, presents significant challenges for optical transceivers in communication networks and high-performance computing systems. Specifically, there is a growing need to significantly increase data rates while reducing energy consumption and cost. High-performance optical modulators based on materials such as InP, thin-film lithium niobate (LiNbO3), or plasmonics have been developed, with LiNbO3 excelling in high-speed and low-voltage modulation. Nonetheless, the widespread industrial adoption of thin film LiNbO3 remains compounded by the rather high cost of the underlying 'on insulator' substrates -- in sharp contrast to silicon photonics, which can benefit from strong synergies with high-volume applications in conventional microelectronics. Here, we demonstrate an integrated 110 GHz modulator using thin-film lithium tantalate (LiTaO3) -- a material platform that is already commercially used for millimeter-wave filters and that can hence build upon technological and economic synergies with existing high-volume applications to offer scalable low-cost manufacturing. We show that the LiTaO3 photonic integrated circuit based modulator can support 176 GBd PAM8 transmission at net data rates exceeding 400 Gbit/s. Moreover, we show that using silver electrodes can reduce microwave losses compared to previously employed gold electrodes. Our demonstration positions LiTaO3 modulator as a novel and highly promising integration platform for next-generation high-speed, energy-efficient, and cost-effective transceivers.

physics.optics↗

arXiv2024

Integrated Triply Resonant Electro-Optic Frequency Comb in Lithium Tantalate

Integrated frequency comb generators based on Kerr parametric oscillation have led to chip-scale, gigahertz-spaced combs with new applications spanning hyperscale telecommunications, low-noise microwave synthesis, LiDAR, and astrophysical spectrometer calibration. Recent progress in lithium niobate (LN) photonic integrated circuits (PICs) has resulted in chip-scale electro-optic (EO) frequency combs, offering precise comb-line positioning and simple operation without relying on the formation of dissipative Kerr solitons. However, current integrated EO combs face limited spectral coverage due to the large microwave power required to drive the non-resonant capacitive electrodes and the strong intrinsic birefringence of Lithium Niobate. Here, we overcome both challenges with an integrated triply resonant architecture, combining monolithic microwave integrated circuits (MMICs) with PICs based on the recently emerged thin-film lithium tantalate. With resonantly enhanced EO interaction and reduced birefringence in Lithium Tantalate, we achieve a four-fold comb span extension and a 16-fold power reduction compared to the conventional non-resonant microwave design. Driven by a hybrid-integrated laser diode, the comb spans over 450nm (60THz) with >2000 lines, and the generator fits within a compact 1cm^2 footprint. We additionally observe that the strong EO coupling leads to an increased comb existence range approaching the full free spectral range of the optical microresonator. The ultra-broadband comb generator, combined with detuning-agnostic operation, could advance chip-scale spectrometry and ultra-low-noise millimeter wave synthesis and unlock octave-spanning EO combs. The methodology of co-designing microwave and optical resonators can be extended to a wide range of integrated electro-optics applications.

physics.optics↗

arXiv2023

Lithium tantalate electro-optical photonic integrated circuits for high volume manufacturing

Photonic integrated circuits based on Lithium Niobate have demonstrated the vast capabilities afforded by material with a high Pockels coefficient, allowing linear and high-speed modulators operating at CMOS voltage levels for applications ranging from data-center communications and photonic accelerators for AI. However despite major progress, the industrial adoption of this technology is compounded by the high cost per wafer. Here we overcome this challenge and demonstrate a photonic platform that satisfies the dichotomy of allowing scalable manufacturing at low cost, while at the same time exhibiting equal, and superior properties to those of Lithium Niobate. We demonstrate that it is possible to manufacture low loss photonic integrated circuits using Lithium Tantalate, a material that is already commercially adopted for acoustic filters in 5G and 6G. We show that LiTaO3 posses equally attractive optical properties and can be etched with high precision and negligible residues using DUV lithography, diamond like carbon (DLC) as a hard mask and alkaline wet etching. Using this approach we demonstrate microresonators with an intrinsic cavity linewidth of 26.8 MHz, corresponding to a linear loss of 5.6 dB/m and demonstrate a Mach Zehnder modulator with Vpi L = 4.2 V cm half-wave voltage length product. In comparison to Lithium Niobate, the photonic integrated circuits based on LiTaO3 exhibit a much lower birefringence, allowing high-density circuits and broadband operation over all telecommunication bands (O to L band), exhibit higher photorefractive damage threshold, and lower microwave loss tangent. Moreover, we show that the platform supports generation of soliton microcombs in X-Cut LiTaO3 racetrack microresonator with electronically detectable repetition rate, i.e. 30.1 GHz.

physics.optics↗

arXiv2022

A heterogeneously integrated lithium niobate-on-silicon nitride photonic platform

The availability of thin-film lithium niobate on insulator (LNOI) and advances in processing have led to the emergence of fully integrated LiNbO3 electro-optic devices, including low-voltage, high-speed modulators, electro-optic frequency combs, and microwave-optical transducers. Yet to date, LiNbO3 photonic integrated circuits (PICs) have mostly been fabricated using non-standard etching techniques that lack the reproducibility routinely achieved in silicon photonics. Widespread future application of thin-film LiNbO3 requires a reliable and scalable solution using standard processing and precise lithographic control. Here we demonstrate a heterogeneously integrated LiNbO3 photonic platform that overcomes the abovementioned challenges by employing wafer-scale bonding of thin-film LiNbO3 to planarized low-loss silicon nitride (Si3N4) photonic integrated circuits, a mature foundry-grade integrated photonic platform. The resulting devices combine the substantial Pockels effect of LiNbO3 with the scalability, high-yield, and complexity of the underlying Si3N4 PICs. Importantly, the platform maintains the low propagation loss (<0.1 dB/cm) and efficient fiber-to-chip coupling (<2.5 dB per facet) of the Si3N4 waveguides. We find that ten transitions between a mode confined in the Si3N4 PIC and the hybrid LiNbO$_3$ mode produce less than 0.8 dB additional loss, corresponding to a loss per transition not exceeding 0.1 dB. These nearly lossless adiabatic transitions thus link the low-loss passive Si3N4 photonic structures with electro-optic components. We demonstrate high-Q microresonators, optical splitters, electrically tunable photonic dimers, electro-optic frequency combs, and carrier-envelope phase detection of a femtosecond laser on the same platform, thus providing a reliable and foundry-ready solution to low-loss and complex LiNbO3 integrated photonic circuits.

physics.optics↗

arXiv2022

Protected generation of dissipative Kerr solitons in supermodes of coupled optical microresonators

The driven-dissipative photonic dimer comprised of two evanescently coupled high-Q microresonators is a fundamental element of multimode soliton lattices. It has demonstrated a variety of emergent nonlinear phenomena including supermode soliton generation, symmetry breaking, and soliton hopping. In this article, we present another aspect of dissipative soliton generation in coupled resonators, revealing the advantages of this system over conventional single resonator platforms. Namely, we show that the accessibility of solitons drastically varies for symmetric and antisymmetric supermode families of the dimer. Linear measurements reveal that the coupling between transverse modes, which gives rise to avoided mode crossings, can be almost completely suppressed. We explain the origin of this phenomenon and show its crucial influence on the dissipative Kerr soliton formation process in lattices of coupled high-Q resonators of any type. Choosing a particular example of the topological Su-Schrieffer-Heeger model, we demonstrate how the edge state can be protected from the interaction with higher-order modes, allowing for the formation of topological Kerr solitons.

physics.optics↗

arXiv2022

Ultrafast tunable lasers using lithium niobate integrated photonics

Recent advances in the processing of thin-film LNOI have enabled low-loss photonic integrated circuits, modulators with improved half-wave voltage, electro-optic frequency combs and novel on-chip electro-optic devices, with applications ranging from 5G telecommunication and microwave photonics to microwave-to-optical quantum interfaces. Lithium niobate integrated photonic circuits could equally be the basis of integrated narrow-linewidth frequency-agile lasers. Pioneering work on polished lithium niobate crystal resonators has led to the development of electrically tunable narrow-linewidth lasers. Here we report low-noise frequency-agile lasers based on lithium niobate integrated photonics and demonstrate their use for coherent laser ranging. This is achieved through heterogeneous integration of ultra-low-loss silicon nitride photonic circuits with thin-film lithium niobate via direct wafer bonding. This platform features low propagation loss of 8.5 dB/m enabling narrow-linewidth lasing (intrinsic linewidth of 3 kHz) by self-injection locking to a III-V semiconductor laser diode. The hybrid mode of the resonator allows electro-optical laser frequency tuning at a speed of 12 PHz/s with high linearity, low hysteresis and while retaining narrow linewidth. Using this hybrid integrated laser, we perform a proof-of-concept FMCW LiDAR ranging experiment, with a resolution of 15 cm. By fully leveraging the high electro-optic coefficient of lithium niobate, with further improvements in photonic integrated circuits design, these devices can operate with CMOS-compatible voltages, or achieve mm-scale distance resolution. Endowing low loss silicon nitride integrated photonics with lithium niobate, gives a platform with wide transparency window, that can be used to realize ultrafast tunable lasers from the visible to the mid-infrared, with applications from OCT and LiDAR to environmental sensing.

physics.optics↗

arXiv2022

Tightly confining lithium niobate photonic integrated circuits and lasers

Photonic integrated circuits are indispensible for data transmission within modern datacenters and pervade into multiple application spheres traditionally limited for bulk optics, such as LiDAR and biosensing. Of particular interest are ferroelectrics such as Lithium Niobate, which exhibit a large electro-optical Pockels effect enabling ultrafast and efficient modulation, but are difficult to process via dry etching . For this reason, etching tightly confining waveguides - routinely achieved in silicon or silicon nitride - has not been possible. Diamond-like carbon (DLC) was discovered in the 1950s and is a material that exhibits an amorphous phase, excellent hardness, and the ability to be deposited in nano-metric thin films. It has excellent thermal, mechanical, and electrical properties, making it an ideal protective coating. Here we demonstrate that DLC is also a superior material for the manufacturing of next-generation photonic integrated circuits based on ferroelectrics, specifically Lithium Niobate on insulator (LNOI). Using DLC as a hard mask, we demonstrate the fabrication of deeply etched, tightly confining, low loss photonic integrated circuits with losses as low as 5.6 dB/m. In contrast to widely employed ridge waveguides, this approach benefits from a more than 1 order of magnitude higher area integration density while maintaining efficient electro-optical modulation, low loss, and offering a route for efficient optical fiber interfaces. As a proof of concept, we demonstrate a frequency agile hybrid integrated III-V Lithium Niobate based laser with kHz linewidth and tuning rate of 0.7 Peta-Hertz per second with excellent linearity and CMOS-compatible driving voltage. Our approach can herald a new generation of tightly confining ferroelectric photonic integrated circuits.

physics.optics↗

arXiv2022

Reduced Material Loss in Thin-film Lithium Niobate Waveguides

Thin-film lithium niobate has shown promise for scalable applications ranging from single-photon sources to high-bandwidth data communication systems. Realization of the next generation high-performance classical and quantum devices, however, requires much lower optical losses than the current state of the art ($\sim$10 million). Unfortunately, material limitations of ion-sliced thin-film lithium niobate have not been explored, and therefore it is unclear how high-quality factor can be achieved in this platform. Here we evaluate the material limited quality factor of thin-film lithium niobate photonic platform can be as high as $Q\approx 1.8\times10^{8}$ at telecommunication wavelengths, corresponding to a propagation loss of 0.2 dB/m.

physics.optics↗

arXiv2021

Dissipative Kerr solitons in a photonic dimer on both sides of exceptional point

Exceptional points are a ubiquitous concept widely present in driven-dissipative coupled systems described by a non-Hermitian Hamiltonian. It is characterized by the degeneracy of the Hamiltonian's eigenvalues and coalescence of corresponding eigenvectors. Recent developments demonstrated that exceptional points can play an important role in photonics. However, to date, exceptional points have been extensively examined in the systems supporting only a few optical modes, thereby leaving the observation of collective (multimode) effects outside of the scope of study. In the present paper, we analyze the role of exceptional points in nonlinear multimode photonics. Specifically, we provide insights into complex nonlinear dynamics arising in a continuous wave-driven pair of strongly coupled nonlinear micro-resonators (i.e. a nonlinear photonic dimer) operating in the multimode regime. Investigating this system, which is known to possess exceptional points, we find two fundamentally different nonlinear regimes of operation corresponding to effective parity-time symmetric and broken parity-time symmetry states. We demonstrate that the photonic dimer can be critically coupled to a bus waveguide, thereby, providing an efficient generation of the dissipative Kerr solitons on both sides of the exceptional point. The parity-time symmetric case, which corresponds to a pair of symmetrically split resonances, has been recently shown to exhibit a variety of emergent phenomena including gear soliton generation, symmetry breaking, and soliton hopping. Dissipative solitons generation in the parity-time symmetry broken case - leading to the dissipation splitting - up to now remains unexplored.

physics.optics↗

arXiv2020

Low-loss integrated nanophotonic circuits with layered semiconductor materials

Monolayer transition metal dichalcogenides with direct bandgaps are emerging candidates for microelectronics, nano-photonics, and optoelectronics. Transferred onto photonic integrated circuits (PICs), these semiconductor materials have enabled new classes of light-emitting diodes, modulators and photodetectors, that could be amenable to wafer-scale manufacturing. For integrated photonic devices, the optical losses of the PICs are critical. In contrast to silicon, silicon nitride (Si3N4) has emerged as a low-loss integrated platform with a wide transparency window from ultraviolet to mid-infrared and absence of two-photon absorption at telecommunication bands. Moreover, it is suitable for nonlinear integrated photonics due to its high Kerr nonlinearity and high-power handing capability. These features of Si3N4 are intrinsically beneficial for nanophotonics and optoelectronics applications. Here we report a low-loss integrated platform incorporating monolayer molybdenum ditelluride (1L-MoTe2) with Si3N4 photonic microresonators. We show that, with the 1L-MoTe2, microresonator quality factors exceeding 3 million in the telecommunication O-band to E-band are maintained. We further investigate the change of microresonator dispersion and resonance shift due to the presence of 1L-MoTe2, and extrapolate the optical loss introduced by 1L-MoTe2 in the telecommunication bands, out of the excitonic transition region. Our work presents a key step for low-loss, hybrid PICs with layered semiconductors without using heterogeneous wafer bonding.

physics.optics↗

arXiv2020

Emergent Nonlinear Phenomena in a Driven Dissipative Photonic Dimer

Emergent phenomena are ubiquitous in nature and refer to spatial, temporal, or spatiotemporal pattern formation in complex nonlinear systems driven out of equilibrium that is not contained in the microscopic descriptions at the single-particle level. Examples range from novel phases of matter in both quantum and classical many-body systems, to galaxy formation or neural dynamics. Two characteristic phenomena are length scales that exceed the characteristic interaction length and spontaneous symmetry breaking. Recent advances in integrated photonics indicate that the study of emergent phenomena is possible in complex coupled nonlinear optical systems. Here we demonstrate that out-of-equilibrium driving of a strongly coupled ("dimer") pair of photonic integrated Kerr microresonators, which at the "single-particle" (i.e. individual resonator) level generate well understood dissipative Kerr solitons, exhibit emergent nonlinear phenomena. By exploring the dimer phase diagram, we find unexpected and therefore unpredicted regimes of soliton hopping, spontaneous symmetry breaking, and periodically emerging (in)commensurate dispersive waves. These phenomena are not included in the single-particle description and related to the parametric frequency conversion between hybridized supermodes. Moreover, by controlling supermode hybridization electrically, we achieve wide tunability of spectral interference patterns between dimer solitons and dispersive waves. Our findings provide the first critical step towards the study of emergent nonlinear phenomena in soliton networks and multimode lattices.

nlin.PS↗