arXiv subjects

Olivier Lai

Publications and source records attributed to Olivier Lai.

At least 19 recordsLinked to original sources

arXiv2026

Wavefront Profiling via correlation of GLAO open loop telemetry

Adaptive Optics (AO) used in ground based observatories can be strengthened in both design and algorithms by a more detailed understanding of the atmosphere they seek to correct. Nowhere is this more true than on Maunakea, where a clearer profile of the atmosphere informs AO system development from the small separations of Extreme AO (ExAO) to the wide field Ground Layer AO (GLAO). Employing telemetry obtained from the 'imaka GLAO demonstrator on the University of Hawaii 2.2-meter telescope, we apply a wind profiling method that identifies turbulent layer velocities through spatial-temporal cross correlations of multiple wavefront sensors (WFSs). We compare the derived layer velocities with nearby wind anemometer data and meteorological model predictions of the upper wind speeds and discuss similarities and differences. The strengths and limitations of this profiling method are evaluated through successful recovery of injected, simulated layers into real telemetry. We detail the profilers' results, including the percentage of data with viable estimates, on four characteristic 'imaka observing runs on open loop telemetry throughout both winter and summer targets. We report on how similar layers are to external measures, the confidence of these results, and the potential for future use of this technique on other multi conjugate AO systems.

astro-ph.IM↗

arXiv2026

Facility integration of the NASA IRTF adaptive secondary mirror

IRTF-ASM-1 has been functioning well since its first light in 2024. This adaptive secondary mirror (ASM) was primarily developed to be an on-sky demonstration of the new hybrid variable reluctance actuator technology at the NASA Infrared Telescope Facility (IRTF). However, due to its physical robustness and our previous demonstrations of sensitivity enhancements with the ASM, we are interested in using it to optimize telescope image quality on a nightly basis. This will directly benefit science observations. However, as IRTF does not currently have adaptive optics expertise, we have been developing the system to be used with minimal human intervention. We present our progress in developing software for active optics mode with IRTF-ASM-1 using the single conjugate, facility 2x2 Shack-Hartmann wavefront sensor Felix. We also present techniques for removing low-order, large amplitude non-common path aberrations between Felix and our science instruments.

astro-ph.IM↗

arXiv2026

Progress report on the integration of the IRTF adaptive secondary mirror

IRTF-ASM-1 is the first on-sky adaptive secondary mirror using the hybrid variable reluctance (HVR) actuators developed by the Netherlands Organization for Applied Scientific Research (TNO). Since its first light in April 2024, the ASM has continued to work consistently well with no hardware issues. The primary purpose of IRTF-ASM-1 is to serve as a demonstration of the HVR actuator technology, both in terms of verifying its robustness and testing calibration methods that are relevant to larger ASMs. However, as the ASM has proven to be easy to handle and reliable in its performance, we are moving toward integrating the ASM for long-term use at IRTF. We present closed loop results with the ASM and IRTF's off-axis facility wavefront sensor FELIX. Correcting the first seven Zernike modes through coma at 90-180 Hz, we are able to enhance the seeing by a factor of 1.8 in FWHM under 0."5 seeing conditions. We also performed the first science observations with the ASM in "static" mode and demonstrated that we can improve the throughput of IRTF's slit spectrograph by approximately a factor of 2, although this requires good reference slopes in FELIX. In the near future, we plan to optimize the calibration of reference slopes in FELIX and streamline the software so that the system can be operated by a non-AO expert.

astro-ph.IM↗

arXiv2026

Using VLTI/GRAVITY+ to determine the identity of a third planet candidate in the PDS 70 system

Detections of protoplanets are rare and protoplanetary disk features mischaracterized as planets are common. PDS 70 is one of only two stars known to host multiple confirmed protoplanets, PDS 70 b and c, and repeat detections of a third point-like source in the system suggest the presence of third inner planet. However, previous observations of this third source are insufficient to distinguish whether it is a planet or a concentrated dust clump in Keplerian motion. Our observations with VLTI/GRAVITY+ did not re-detect this point-like source, suggesting that it is, in fact, a dust clump and not a planet. These observations demonstrate how the angular resolving power of VLTI/GRAVITY+ can be used to distinguish between protoplanets and protoplanetary disk features.

astro-ph.EP↗

arXiv2025

A vision for ground-based astronomy beyond the 2030s: How to build ESO's next big telescope sustainably

Astronomy is the study of the Universe and all the objects that it comprises. Our attention is therefore usually focused beyond Earth, home to the only form of life known today. However, how can we continue to explore the secrets of the Universe, if we stand by and watch our only home burn? We know that there is no Planet B. It is therefore urgent that, as astronomers, we collectively work to protect the Earth, allowing future generations the opportunity to continue to uncover the secrets of the cosmos. As astronomical facilities account for the majority of our community's carbon footprint, we propose guidelines that we hold crucial for the European Southern Observatory (ESO) to consider in the context of the Expanding Horizons programme as it plans a next-generation, transformational facility.

astro-ph.IM↗

arXiv2025

Stellar intensity interferometry in the photon-counting regime

Stellar intensity interferometry consists in measuring the correlation of the light intensity fluctuations at two telescopes observing the same star. The amplitude of the correlation is directly related to the luminosity distribution of the star, which would be unresolved by a single telescope. This technique is based on the well-known Hanbury Brown and Twiss effect. After its discovery in the 1950s, it was used in astronomy until the 1970s, and then replaced by direct (``amplitude'') interferometry, which is much more sensitive, but also much more demanding. However, in recent years, intensity interferometry has undergone a revival. In this article, we present a summary of the state-of-the-art, and we discuss in detail the signal-to-noise ratio of intensity interferometry in the framework of photon-counting detection.

astro-ph.IM↗

arXiv2025

GRAVITY+ adaptive optics (GPAO) tests in Europe

We present in this proceeding the results of the test phase of the GRAVITY+ adaptive optics. This extreme AO will enable both high-dynamic range observations of faint companions (including exoplanets) thanks to a 40x40 sub-apertures wavefront control, and sensitive observations (including AGNs) thanks to the addition of a laser guide star to each UT of the VLT. This leap forward is made thanks to a mostly automated setup of the AO, including calibration of the NCPAs, that we tested in Europe on the UT+atmosphere simulator we built in Nice. We managed to reproduce in laboratory the expected performances of all the modes of the AO, including under non-optimal atmospheric or telescope alignment conditions, giving us the green light to proceed with the Assembly, Integration and Verification phase in Paranal.

astro-ph.IM↗

arXiv2024

First Resolution of Microlensed Images of a Binary-Lens Event

We resolve the multiple images of the binary-lens microlensing event ASASSN-22av using the GRAVITY instrument of the Very Large Telescope Interferometer (VLTI). The light curves show weak binary-lens perturbations, complicating the analysis, but the joint modeling with the VLTI data breaks several degeneracies, arriving at a strongly favored solution. Thanks to precise measurements of angular Einstein radius θ_E = 0.724 +/- 0.002 mas and microlens parallax, we determine that the lens system consists of two M dwarfs with masses of M_1 = 0.258 +/- 0.008 M_sun and M_2 = 0.130 +/- 0.007 M_sun, a projected separation of r_\perp = 6.83 +/- 0.31 au and a distance of D_L = 2.29 +/- 0.08 kpc. The successful VLTI observations of ASASSN-22av open up a new path for studying intermediate-separation (i.e., a few astronomical units) stellar-mass binaries, including those containing dark compact objects such as neutron stars and stellar-mass black holes.

astro-ph.SR↗

arXiv2024

In-lab and On-sky Closed-loop Results of Adaptive Secondary Mirrors with TNO's Hybrid Variable Reluctance Actuators

We performed closed-loop lab testing of large-format deformable mirrors (DMs) with hybrid variable reluctance actuators. TNO has been developing the hybrid variable reluctance actuators in support for a new generation of adaptive secondary mirrors (ASMs), which aim to be more robust and reliable. Compared to the voice coil actuators, this new actuator technology has a higher current to force efficiency, and thus can support DMs with thicker facesheets. Before putting this new technology on-sky, it is necessary to understand how to control it and how it behaves in closed-loop. We performed closed-loop tests with the Shack-Hartmann wavefront sensor with three large-format deformable mirrors that use the TNO actuators: DM3, FLASH, and IRTF-ASM-1 ASM. The wavefront sensor and the real-time control systems were developed for the NASA Infrared Telescope Facility (IRTF) and the UH 2.2-meter telescope ASMs. We tested IRTF-ASM-1 on-sky and proved that it meets all of our performance requirements. This work presents our lab setup for the experiments, the techniques we have employed to drive these new ASMs, the results of our closed-loop lab tests for FLASH and IRTF-ASM-1, and the on-sky closed-loop results of IRTF-ASM-1 ASM.

astro-ph.IM↗

arXiv2024

First laboratory and on-sky results of an adaptive secondary mirror with TNO-style actuators on the NASA Infrared Telescope Facility

We are developing an adaptive secondary mirror (ASM) that uses a new actuator technology created by the Netherlands Organization for Applied Scientific Research (TNO). The TNO hybrid variable reluctance actuators have more than an order of magnitude better efficiency over the traditional voice coil actuators that have been used on existing ASMs and show potential for improving the long-term robustness and reliability of ASMs. To demonstrate the performance, operations, and serviceability of TNO's actuators in an observatory, we have developed a 36-actuator prototype ASM for the NASA Infrared Telescope Facility (IRTF) called IRTF-ASM-1. IRTF-ASM-1 provides the first on-sky demonstration of this approach and will help us evaluate the long-term performance and use of this technology in an astronomical facility environment. We present calibration and performance results with the ASM in a Meniscus Hindle Sphere lens setup as well as preliminary on-sky results on IRTF. IRTF-ASM-1 achieved stable closed-loop performance on-sky with H-band Strehl ratios of 35-40% in long-exposure images under a variety of seeing conditions.

astro-ph.IM↗

arXiv2024

DanceCam: atmospheric turbulence mitigation in wide-field astronomical images with short-exposure video streams

We introduce a novel technique to mitigate the adverse effects of atmospheric turbulence on astronomical imaging. Utilizing a video-to-image neural network trained on simulated data, our method processes a sliding sequence of short-exposure ($\sim$0.2s) stellar field images to reconstruct an image devoid of both turbulence and noise. We demonstrate the method with simulated and observed stellar fields, and show that the brief exposure sequence allows the network to accurately associate speckles to their originating stars and effectively disentangle light from adjacent sources across a range of seeing conditions, all while preserving flux to a lower signal-to-noise ratio than an average stack. This approach results in a marked improvement in angular resolution without compromising the astrometric stability of the final image.

astro-ph.IM↗

arXiv2023

V(WF)$^2$S: Very Wide Field WaveFront Sensor for GLAO

Adaptive optics is a technique mostly used on large telescopes. It turns out to be challenging for smaller telescopes (0.5~2m) due to the small isoplanatic angle, small subapertures and high correction speeds needed at visible wavelengths, requiring bright stars for guiding, severely limiting the sky coverage. NGS SCAO is ideal for planetary objects but remains limited for general purpose observing. The approach we consider is a compromise between image quality gain and sky coverage: we propose to partially improve the image quality anywhere in the sky instead of providing the diffraction limit around a few thousand bright stars. We suggest a new solution based on multiple AO concepts brought together: The principle is based on a rotating Foucault test, like the first AO concept proposed by H. Babcock in 1953, on the Ground Layer Adaptive Optics, proposed by Rigaut and Tokovinin in the early 2000s, and on the idea of Layer-oriented MCAO and the pupil-plane wavefront analysis by R. Ragazzoni. We propose to combine these techniques to use all the light available in a large field to measure the ground layer turbulence and enable the high angular resolution imaging of regions of the sky (e.g., nebulas, galaxies) inaccessible to traditional AO systems. The motivation to develop compact and robust AO system for small telescopes is two-fold: On the one hand, universities often have access to small telescopes as part of their education programs. Also, researchers in countries with fewer resources could also benefit from reliable adaptive optics system on smaller telescopes for research and education purposes. On the other hand, amateur astronomers and enthusiasts want improved image quality for visual observation and astrophotography. Implementing readily accessible adaptive optics in astronomy clubs would also likely have a significant impact on citizen science.

astro-ph.IM↗

arXiv2023

Observing exoplanets from Antarctica in two colours: Set-up and operation of ASTEP+

On December 2021, a new camera box for two-colour simultaneous visible photometry was successfully installed on the ASTEP telescope at the Concordia station in Antarctica. The new focal box offers increased capabilities for the ASTEP+ project. The opto-mechanical design of the camera was described in a previous paper. Here, we focus on the laboratory tests of each of the two cameras, the low-temperature behaviour of the focal box in a thermal chamber, the on-site installation and alignment of the new focal box on the telescope, the measurement of the turbulence in the tube and the operation of the telescope equipped with the new focal box. We also describe the data acquisition and the telescope guiding procedure and provide a first assessment of the performances reached during the first part of the 2022 observation campaign. Observations of the WASP19 field, already observed previously with ASTEP, demonstrates an improvement of the SNR by a factor 1.7, coherent with an increased number of photon by a factor of 3. The throughput of the two cameras is assessed both by calculation of the characteristics of the optics and quantum efficiency of the cameras, and by direct observations on the sky. We find that the ASTEP+ two-colour transmission curves (with a dichroic separating the fluxes at 690nm) are similar to those of GAIA in the blue and red channels, but with a lower transmission in the ASTEP+ red channel leading to a 1.5 magnitude higher B-R value compared to the GAIA B-R value. With this new setting, the ASTEP+ telescope will ensure the follow-up and the characterization of a large number of exoplanetary transits in the coming years in view of the future space missions JWST and Ariel.

astro-ph.IM↗

arXiv2023

The GRAVITY+ Project: Towards All-sky, Faint-Science, High-Contrast Near-Infrared Interferometry at the VLTI

The GRAVITY instrument has been revolutionary for near-infrared interferometry by pushing sensitivity and precision to previously unknown limits. With the upgrade of GRAVITY and the Very Large Telescope Interferometer (VLTI) in GRAVITY+, these limits will be pushed even further, with vastly improved sky coverage, as well as faint-science and high-contrast capabilities. This upgrade includes the implementation of wide-field off-axis fringe-tracking, new adaptive optics systems on all Unit Telescopes, and laser guide stars in an upgraded facility. GRAVITY+ will open up the sky to the measurement of black hole masses across cosmic time in hundreds of active galactic nuclei, use the faint stars in the Galactic centre to probe General Relativity, and enable the characterisation of dozens of young exoplanets to study their formation, bearing the promise of another scientific revolution to come at the VLTI.

astro-ph.IM↗

arXiv2023

Intensity Interferometry observations of the H$α$ envelope of $γ$ Cas with MéO and a portable telescope

We report on observations of the extended environment of the bright Be star $γ$-Cas performed using intensity interferometry measurements within its H$α$ emission line. These observations were performed using a modified version of the I2C intensity interferometry instrument installed onto the 1.54 meter MéO optical metrology telescope and a portable 1-meter telescope (T1M). In order to better constrain the extent of the H$α$ envelope, observations were performed for two different positions of the T1M telescope, corresponding to an intermediate and long baselines in which the extended region was partially and fully resolved. We find that the observed data are consistent with past interferometric observations of $γ$-Cas. These observations demonstrate the capability to equip optical telescopes of different optical designs with intensity interferometry capabilities and illustrate the potential to scale a similar system onto many additional telescopes.

astro-ph.IM↗

arXiv2022

Intensity Interferometry at Calern and beyond: progress report

We present the current status of the I2C stellar intensity interferometer used towards high angular resolution observations of stars in visible wavelengths. In these proceedings, we present recent technical improvements to the instrument, and share results from ongoing campaigns using arrays of small diameter optical telescopes. A tip-tilt adaptive optics unit was integrated into the optical system to stabilize light injection into an optical fiber. The setup was successfully tested with several facilities on the Calern Plateau site of the Observatoire de la Côte d'Azur. These include one of the 1 m diameter telescopes of the C2PU observatory, a portable 1 m diameter telescope, and also the 1.5 m MéO telescope. To better constrain on-sky measurements, the spectral transmission of instrument was characterized in the laboratory using a high resolution spectrograph. The system was also tested with two of the auxiliary telescopes of the VLTI resulting in successful temporal and spatial correlation measurements of three stars.

astro-ph.IM↗

arXiv2022

Building a GRAVITY+ Adaptive Optics Test Bench

We present the testbench aimed at integrating the GRAVITY+ adaptive optics GPAO. It consists of two independent elements, one reproducing the Coud{é} focus of the telescope, including the telescope deformable mirror mount (with its surface facing down), and one reproducing the Coud{é} room opto-mechanical environment, including a downwards-propagating beam, and the telescope mechanical interfaces in order to fit in the new GPAO wavefront sensor. We discuss in this paper the design of this bench and the solutions we adopted to keep the cost low, keep the design compact (allowing it to be fully contained in a 20 sqm clean room), and align the bench independently from the adaptive optics. We also discuss the features we have set in this bench.

astro-ph.IM↗

arXiv2022

Observation Scheduling and Automatic Data Reduction for the Antarctic telescope, ASTEP+

The possibility to observe transiting exoplanets from Dome C in Antarctica provides immense benefits: stable weather conditions, limited atmospheric turbulence, and a night that lasts almost three months due to the austral winter. However, this site also presents significant limitations, such as limited access for maintenance and internet speeds of only a few KB/s. This latter factor means that the approximately 6 TB of data collected annually must be processed on site automatically, with only final data products being sent once a day to Europe. In this context, we present the current state of operations of ASTEP+, a 40 cm optical telescope located at Concordia Station in Antarctica. Following a successful summer campaign, ASTEP+ has begun the 2022 observing season with a brand-new two-colour photometer with increased sensitivity. A new Python data analysis pipeline installed on a dedicated server in Concordia will significantly improve the precision of the extracted photometry, enabling us to get higher signal-to-noise transit detections. The new pipeline additionally incorporates automatic transit modelling to reduce the amount of manual post-processing required. It also handles the automatic daily transfer of the photometric lightcurves and control data to Europe. Additionally, we present the Python and web-based systems used for selection and scheduling of transit observations; these systems have wide applicability for the scheduling of other astronomical observations with strong time constraints. We also review the type of science that ASTEP+ will be conducting and analyse how unique ASTEP+ is to exoplanet transit research.

astro-ph.EP↗