arXiv subjects

Ondrej Dyck

Publications and source records attributed to Ondrej Dyck.

At least 19 recordsLinked to original sources

arXiv2026

Foundry CMOS platform for multimodal quantum materials characterization

Quantum materials experiments increasingly rely on microwave, electrical, thermal, optical, and structural probes, but these capabilities are typically assembled from custom hardware that limits reproducibility and scalability. Here we show that a commercial 65-nm CMOS process can be repurposed as a passive, foundry-manufacturable characterization platform by functionally partitioning its metal stack into microwave, thermal, and electrical subsystems within a 1 mm2 footprint. The integrated RF architecture enables cryogenic magnetic susceptibility measurements of Fe3GeTe2 heterostructures at 1.75 K without sample-specific fabrication. We further demonstrate NV-center optically detected magnetic resonance (ODMR) with >20% contrast at 4-9 dBm microwave power, reducing power requirements by 20-25 dB relative to conventional antenna-based approaches while maintaining sensitivities of 2-3 uT/sqrt(Hz). We additionally confirm compatibility with in-situ electron-beam imaging, showing no measurable degradation in image quality upon device operation. These results establish a scalable, foundry-manufacturable platform for multimodal quantum sensing and materials characterization.

cond-mat.mtrl-sci↗

arXiv2026

Inference-Sufficient Representations for High-Throughput Measurement: Lessons from Lossless Compression Benchmarks in 4D-STEM

Four-dimensional scanning transmission electron microscopy (4D-STEM) generates multi-gigabyte datasets, creating a growing mismatch between acquisition rates and practical storage, transfer, and interactive visualization capabilities. We systematically benchmark 13 lossless compression implementations across 5 representative datasets (8~MiB to 8~GiB, 49.5--92.8\% sparsity), with 10 independent runs per method. HDF5 provides built-in gzip compression, of which gzip-9 typically achieves the highest compression ratio but is slow. We therefore evaluate widely available alternatives (via hdf5plugin), including the Blosc family. As a representative comparison, blosc\_zstd achieves compression comparable to gzip-9 (mean 13.5$\times$ vs 12.3$\times$) while compressing 19--69$\times$ faster and reading 1.9--2.6$\times$ faster across datasets. Compression ratios are deterministic, and timing measurements are highly reproducible (CV $<$2\%). Compression performance follows a power law with sparsity ($R^2 = 0.99$), ranging from 5$\times$ for moderately sparse data to 35$\times$ for highly sparse data. We identify six top-performing implementations optimized for different use cases and demonstrate that 4D-STEM data can be routinely compressed by $>$10$\times$. While these results provide practical guidance for lossless compression selection, the broader conclusion is that lossless compression preserves measurements but does not by itself guarantee sustainable high-throughput workflows. As detector rates rise, data handling will increasingly require inference-driven representations -- i.e., deciding what must be preserved to support a scientific inference, rather than defaulting to storing fully dense raw measurements.

eess.SP↗

arXiv2026

Atomically Precise Electron Beam Sculpting of Bilayer h-BN: The Role of Crystallographic Orientation and Milling Strategy

Achieving atomic precision in top-down manufacturing remains a fundamental challenge nanofabrication technology. Here, the focused electron beam of a scanning transmission electron microscope is used to demonstrate atomically precise sculpting of hexagonal boron nitride (h-BN) bilayers, achieving nanoribbons as narrow as 6 Å with atomically smooth edges. The key to this precision lies in understanding how the underlying atomic structure, particularly in twisted bilayer systems, influences the milling process. High-angle annular dark-field imaging combined with multislice simulations reveals distinct intensity signatures that allow identification of different stacking arrangements within moiré patterns. Mathematical analysis of moiré lattices provides a predictive framework for determining optimal cutting directions, with cuts along armchair directions yielding superior edge quality compared to zigzag orientations. Surprisingly, a sequential milling approach, where a small electron beam subscan area is translated during the process, produces significantly better results than parallel milling of the entire target region. To understand these differences we implemented a stochastic milling model that reveals that sequential milling minimizes unwanted exposure to surrounding material through beam tail effects. These findings establish a framework for achieving atomic precision in electron beam sculpting of two-dimensional materials and provide fundamental insights applicable to the broader challenge of top-down nanofabrication.

cond-mat.mtrl-sci↗

arXiv2025

Defect Engineering in Large-Scale CVD-Grown Hexagonal Boron Nitride: Formation, Spectroscopy, and Spin Relaxation Dynamics

Recently, numerous techniques have been reported for generating optically active defects in exfoliated hexagonal boron nitride (hBN), which hold transformative potential for quantum photonic devices. However, achieving on-demand generation of desirable defect types in scalable hBN films remains a significant challenge. Here, we demonstrate that formation of negative boron vacancy defects, VB-, in suspended, large-area CVD-grown hBN is strongly dependent on the type of bombarding particles (ions, neutrons, and electrons) and irradiation conditions. In contrast to suspended hBN, defect formation in substrate-supported hBN is more complex due to the uncontrollable generation of secondary particles from the substrate, and the outcome strongly depends on the thickness of the hBN. We identify different defect types by correlating spectroscopic and optically detected magnetic resonance features, distinguishing boron vacancies (formed by light ions and neutrons) from other optically active defects emitting at 650 nm assigned to anti-site nitrogen vacancy (NBVN) and reveal the presence of additional dark paramagnetic defects that influence spin-lattice relaxation time (T1) and zero-field splitting parameters, all of which strongly depend on the defect density. These results underscore the potential for precisely engineered defect formation in large-scale CVD-grown hBN, paving the way for the scalable fabrication of quantum photonic devices.

cond-mat.mtrl-sci↗

arXiv2024

A Versatile Side Entry Laser System for Scanning Transmission Electron Microscopy

We present the design and implementation of a side entry laser system designed for an ultra-high vacuum scanning transmission electron microscope. This system uses a versatile probe design enclosed in a vacuum envelope such that parts can be easily aligned, modified, or exchanged without disturbing the vacuum. The system uses a mirror mounted on the sample holder such that the sample can be illuminated without being tilted. Notably the mirror can be removed and replaced with an ablation target and a higher power laser used to ablate material directly onto the sample. We argue that new capabilities hold the potential to transform the electron microscope from an analysis tool towards a more flexible synthesis system, where atomic scale fabrication and atom-by-atom experiments can be performed.

physics.app-ph↗

arXiv2024

Your Clean Graphene is Still Not Clean

Efforts aimed at scaling fabrication processes to the level of single atoms, dubbed atom-by-atom fabrication or atomic fabrication, invariably encounter the obstacle of atomic scale cleanliness. When considering atomic fabrication, cleanliness of the base material and purity of the source reservoir from which atomic structures will be built are invariable constraints imposed by laws of physics and chemistry. As obvious as such statements may be, and regardless of the inevitable consequences for successful atomic fabrication, there is a poignant lack of understanding of the "dirt" (contamination/impurities). Here, we examine hydrocarbon contamination on graphene. Graphene has formed the base substrate for many e-beam-based atomic fabrication studies and many strategies for cleaning graphene have been presented in the literature. One popular method is heating to high temperatures (>500 °C). It is usually inferred that volatile hydrocarbons evaporate into the microscope vacuum system leaving behind pristine graphene. Here, we show through direct image intensity analysis that what appears to be clean graphene can be coated with a thin layer of dynamically diffusing hydrocarbons. This result holds significant implications for approaches to e-beam based atomic fabrication, updates the conceptual model of e-beam induced hydrocarbon deposition, and may extend to hot surfaces generally.

cond-mat.mtrl-sci↗

arXiv2023

Closed-Loop Electron-Beam-Induced Spectroscopy and Nanofabrication Around Individual Quantum Emitters

Color centers in diamond play a central role in the development of quantum photonic technologies, and their importance is only expected to grow in the near future. For many quantum applications, high collection efficiency from individual emitters is required, but the refractive index mismatch between diamond and air limits the optimal collection efficiency with conventional diamond device geometries. While different out-coupling methods with near-unity efficiency exist, many have yet to be realized due to current limitations in nanofabrication methods, especially for mechanically hard materials like diamond. Here, we leverage electron-beam-induced etching to modify Sn-implanted diamond quantum microchiplets containing integrated waveguides with width and thickness of 280 nm and 200 nm, respectively. This approach allows for simultaneous high-resolution imaging and modification of the host matrix with an open geometry and direct writing. When coupled with the cathodoluminescence signal generated from the electron-emitter interactions, we can monitor the enhancement of the quantum emitters in real-time with nanoscale spatial resolution. The operando measurement and manipulation of single photon emitters demonstrated here provides a new foundation for the control of emitter-cavity interactions in integrated quantum photonics.

physics.optics↗

arXiv2023

Controlling hydrocarbon transport and electron beam induced deposition on single layer graphene: toward atomic scale synthesis in the scanning transmission electron microscope

Focused electron beam induced deposition (FEBID) is a direct write technique for depositing materials on a support substrate akin to 3D printing with an electron beam (e-beam). Opportunities exist for merging this existing technique with aberration-corrected scanning transmission electron microscopy to achieve molecular- or atomic-level spatial precision. Several demonstrations have been performed using graphene as the support substrate. A common challenge that arises during this process is e-beam-induced hydrocarbon deposition, suggesting greater control over the sample environment is needed. Various strategies exist for cleaning graphene in situ. One of the most effective methods is to rapidly heat to high temperatures, e.g., 600 C or higher. While this can produce large areas of what appears to be atomically clean graphene, mobile hydrocarbons can still be present on the surfaces. Here, we show that these hydrocarbons are primarily limited to surface migration and demonstrate an effective method for interrupting the flow using e-beam deposition to form corralled hydrocarbon regions. This strategy is effective for maintaining atomically clean graphene at high temperatures where hydrocarbon mobility can lead to substantial accumulation of unwanted e-beam deposition.

cond-mat.mtrl-sci↗

arXiv2023

Doping transition-metal atoms in graphene for atomic-scale tailoring of electronic, magnetic, and quantum topological properties

Atomic-scale fabrication is an outstanding challenge and overarching goal for the nanoscience community. The practical implementation of moving and fixing atoms to a structure is non-trivial considering that one must spatially address the positioning of single atoms, provide a stabilizing scaffold to hold structures in place, and understand the details of their chemical bonding. Free-standing graphene offers a simplified platform for the development of atomic-scale fabrication and the focused electron beam in a scanning transmission electron microscope can be used to locally induce defects and sculpt the graphene. In this scenario, the graphene forms the stabilizing scaffold and the experimental question is whether a range of dopant atoms can be attached and incorporated into the lattice using a single technique and, from a theoretical perspective, we would like to know which dopants will create technologically interesting properties. Here, we demonstrate that the electron beam can be used to selectively and precisely insert a variety of transition metal atoms into graphene with highly localized control over the doping locations. We use first-principles density functional theory calculations with direct observation of the created structures to reveal the energetics of incorporating metal atoms into graphene and their magnetic, electronic, and quantum topological properties.

cond-mat.mtrl-sci↗

arXiv2023

The role of temperature on defect diffusion and nanoscale patterning in graphene

Graphene is of great scientific interest due to a variety of unique properties such as ballistic transport, spin selectivity, the quantum hall effect, and other quantum properties. Nanopatterning and atomic scale modifications of graphene are expected to enable further control over its intrinsic properties, providing ways to tune the electronic properties through geometric and strain effects, introduce edge states and other local or extended topological defects, and sculpt circuit paths. The focused beam of a scanning transmission electron microscope (STEM) can be used to remove atoms, enabling milling, doping, and deposition. Utilization of a STEM as an atomic scale fabrication platform is increasing; however, a detailed understanding of beam-induced processes and the subsequent cascade of aftereffects is lacking. Here, we examine the electron beam effects on atomically clean graphene at a variety of temperatures ranging from 400 to 1000 C. We find that temperature plays a significant role in the milling rate and moderates competing processes of carbon adatom coalescence, graphene healing, and the diffusion (and recombination) of defects. The results of this work can be applied to a wider range of 2D materials and introduce better understanding of defect evolution in graphite and other bulk layered materials.

cond-mat.mes-hall↗

arXiv2023

Doping of Cr in Graphene Using Electron Beam Manipulation for Functional Defect Engineering

Chromium atoms in graphene have been proposed to exhibit magnetic moments and spin-selective conducting states depending on the local bonding geometry within the graphene structure, which could lead to interesting applications in spintronics. Despite this interest, there are few direct experimental reports of Cr dopants in graphene even though it is theorized to be stable. Here, we demonstrate the introduction of single Cr dopant atoms into the graphene lattice and onto graphene edges through the controlled use of a focused electron beam in a scanning transmission electron microscope. We show local control of doping locations and when coupled with targeted in situ milling during scanning of the e-beam, these strategies demonstrate an important component of the fabrication of tailored nanostructured devices in the electron microscope. The approach is validated with first principles calculations to understand synthesis pathways during fabrication and reveal the energetics and local properties of Cr atoms embedded in graphene; e.g., Cr doping can convert graphene into a magnetic and semiconducting material, which suggests Cr-doped graphene can be used as a building block for potential electronic devices and a means to construct them.

cond-mat.mtrl-sci↗

arXiv2023

The Synthescope: A Vision for Combining Synthesis with Atomic Fabrication

The scanning transmission electron microscope, a workhorse instrument in materials characterization, is being transformed into an atomic-scale material manipulation platform. With an eye on the trajectory of recent developments and the obstacles toward progress in this field, we provide a vision for a path toward an expanded set of capabilities and applications. We reconceptualize the microscope as an instrument for fabrication and synthesis with the capability to image and characterize atomic-scale structural formation as it occurs. Further development and refinement of this approach may have substantial impact on research in microelectronics, quantum information science, and catalysis where precise control over atomic scale structure and chemistry of a few "active sites" can have a dramatic impact on larger scale functionality and where developing a better understanding of atomic scale processes can help point the way to larger scale synthesis approaches.

physics.app-ph↗

arXiv2023

Direct-Writing Atom-by-Atom

Direct-write processes enable the alteration or deposition of materials in a continuous, directable, sequential fashion. In this work we demonstrate an electron beam direct-write process in an aberration-corrected scanning transmission electron microscope. This process has several fundamental differences from conventional electron beam induced deposition techniques, where the electron beam dissociates precursor gases into chemically reactive products that bond to a substrate. Here, we use elemental tin (Sn) as a precursor and employ a different mechanism to facilitate deposition. The atomic-sized electron beam is used to generate chemically reactive point defects at desired locations in a graphene substrate. Temperature control of the sample is used to enable the precursor atoms to migrate across the surface and bond to the defect sites thereby enabling atom-by-atom direct-writing.

cond-mat.mtrl-sci↗

arXiv2023

A platform for in situ synthesis in a STEM

The engineering of quantum materials requires the development of tools able to address various synthesis and characterization challenges. These include the establishment and refinement of growth methods, material manipulation, and defect engineering. Material modification at the atomic level will be a key enabling factor for the engineering of quantum materials where desired phenomena are critically determined by local atomic structures. Successful use of scanning transmission electron microscopes (STEMs) for atomic scale material manipulation has opened the door for a transformed view of what can be accomplished using electron-beam-based strategies. However, serious obstacles exist on the pathway from possibility to practical reality. One such obstacle is the in situ delivery of atomized material in the STEM to the region of interest for further fabrication processes. Here, we present progress on this front with a view toward performing synthesis (deposition and growth) processes in a scanning transmission electron microscope. An in situ thermal deposition platform is presented, tested, and deposition and growth processes are demonstrated. In particular, we show that isolated Sn atoms can be evaporated from a filament and caught on the nearby sample, demonstrating atomized material delivery. This platform, and future variations, are envisioned to facilitate real-time atomic resolution imaging of growth processes and open new pathways toward atomic fabrication.

cond-mat.mtrl-sci↗

arXiv2023

Top-down fabrication of atomic patterns in twisted bilayer graphene

Atomic-scale engineering typically involves bottom-up approaches, leveraging parameters such as temperature, partial pressures, and chemical affinity to promote spontaneous arrangement of atoms. These parameters are applied globally, resulting in atomic scale features scattered probabilistically throughout the material. In a top-down approach, different regions of the material are exposed to different parameters resulting in structural changes varying on the scale of the resolution. In this work, we combine the application of global and local parameters in an aberration corrected scanning transmission electron microscope (STEM) to demonstrate atomic scale precision patterning of atoms in twisted bilayer graphene. The focused electron beam is used to define attachment points for foreign atoms through the controlled ejection of carbon atoms from the graphene lattice. The sample environment is staged with nearby source materials, such that the sample temperature can induce migration of the source atoms across the sample surface. Under these conditions, the electron-beam (top-down) enables carbon atoms in the graphene to be replaced spontaneously by diffusing adatoms (bottom-up). Using image-based feedback-control, arbitrary patterns of atoms and atom clusters are attached to the twisted bilayer graphene with limited human interaction. The role of substrate temperature on adatom and vacancy diffusion is explored by first-principles simulations.

cond-mat.mtrl-sci↗

arXiv2022

Direct Imaging of Electron Orbitals with a Scanning Transmission Electron Microscope

Recent studies of secondary electron (SE) emission in scanning transmission electron microscopes suggest that material's properties such as electrical conductivity, connectivity, and work function can be probed with atomic scale resolution using a technique known as secondary electron e-beam-induced current (SEEBIC). Here, we apply the SEEBIC imaging technique to a stacked 2D heterostructure device to reveal the spatially resolved electron orbital ionization cross section of an encapsulated WSe2 layer. We find that the double Se lattice site shows higher emission than the W site, which is at odds with first-principles modelling of ionization of an isolated WSe2 cluster. These results illustrate that atomic level SEEBIC contrast within a single material is possible and that an enhanced understanding of atomic scale SE emission is required to account for the observed contrast. In turn, this suggests that subtle information about interlayer bonding and the effect on electron orbitals can be directly revealed with this technique.

cond-mat.mtrl-sci↗

arXiv2022

Probing electron beam induced transformations on a single defect level via automated scanning transmission electron microscopy

The robust approach for real-time analysis of the scanning transmission electron microscopy (STEM) data streams, based on the ensemble learning and iterative training (ELIT) of deep convolutional neural networks, is implemented on an operational microscope, enabling the exploration of the dynamics of specific atomic configurations under electron beam irradiation via an automated experiment in STEM. Combined with beam control, this approach allows studying beam effects on selected atomic groups and chemical bonds in a fully automated mode. Here, we demonstrate atomically precise engineering of single vacancy lines in transition metal dichalcogenides and the creation and identification of topological defects graphene. The ELIT-based approach opens the pathway toward the direct on-the-fly analysis of the STEM data and engendering real-time feedback schemes for probing electron beam chemistry, atomic manipulation, and atom by atom assembly.

cond-mat.dis-nn↗

arXiv2022

Automated experiment in 4D-STEM: exploring emergent physics and structural behaviors

Automated experiments in 4D Scanning Transmission Electron Microscopy are implemented for rapid discovery of local structures, symmetry-breaking distortions, and internal electric and magnetic fields in complex materials. Deep kernel learning enables active learning of the relationship between local structure and a 4D-STEM based descriptors. With this, efficient and "intelligent" probing of dissimilar structural elements to discover desired physical functionality is made possible. This approach allows effective navigation of the sample in an automated fashion guided by either a pre-determined physical phenomenon, such as strongest electric field magnitude, or in an exploratory fashion. We verify the approach first on pre-acquired 4D-STEM data, and further implement it experimentally on an operational STEM. The experimental discovery workflow is demonstrated using graphene, and subsequently extended towards a lesser-known layered 2D van der Waal material, MnPS3. This approach establishes a paradigm for physics-driven automated 4D-STEM experiments that enable probing the physics of strongly correlated systems and quantum materials and devices, as well as exploration of beam sensitive materials.

cond-mat.mtrl-sci↗