arXiv subjects

P. Allport

Publications and source records attributed to P. Allport.

13 recordsLinked to original sources

arXiv2025

Study of MALTA2, a Depleted Monolithic Active Pixel Sensor, with grazing angles at CERN SPS 180 GeV/c hadron beam

MALTA2 is a Depleted Monolithic Active Pixel Sensor designed to meet the challenging requirements of future collider experiments, in particularly extreme radiation tolerance and high hit rate. The sensor is fabricated in a modified Tower 180 nm CMOS imaging technology to mitigate performance degradation caused by 100 MRad of Total Ionising Dose and greater than 10^{15} 1 MeV n_{eq}/cm^2 of Non-Ionising Energy Loss. MALTA2 samples have been tested during the CERN SPS test beam campaign in 2023-2024, before and after irradiation at a fluence of 1 $\times$ 10^{15} 1 MeV n_{eq}/cm^2. The sensors were positioned at various inclinations relative to the beam, covering grazing angles from 0 to 60 degrees. This contribution presents measurements of detection efficiency and cluster size as functions of these angles, along with an estimation of the active depth of the depleted region based on the test beam results.

hep-ex↗

arXiv2025

Timing characterization of MALTA and MALTA2 pixel detectors using Micro X-ray source

The MALTA monolithic active pixel detector is developed to address some of the challenges anticipated in future high-energy physics detectors. As part of its characterization, we conducted timing studies necessary to provide a figure of merit for this family of monolithic pixel detectors. MALTA has a metal layer in front-end electronics, and the conventional laser technique is not suitable for timing studies due to the reflection of the laser from the metallic surface. X-rays have been employed as a more effective alternative for penetration through these layers. The triggered X-ray set-up is designed to study timing measurements of monolithic detectors. The timing response of the X-ray set-up is characterized using an LGAD. The timing response of the MALTA and MALTA2 pixel detectors is studied, and the best response time of MALTA2 pixel detectors is measured at about 2.6 ns.

physics.ins-det↗

arXiv2023

MALTA-Cz: A radiation hard full-size monolithic CMOS sensor with small electrodes on high-resistivity Czochralski substrate

Depleted Monolithic Active Pixel Sensor (DMAPS) sensors developed in the Tower Semiconductor 180 nm CMOS imaging process have been designed in the context of the ATLAS ITk upgrade Phase-II at the HL-LHC and for future collider experiments. The "MALTA-Czochralski (MALTA-Cz)" full size DMAPS sensor has been developed with the goal to demonstrate a radiation hard, thin CMOS sensor with high granularity, high hit-rate capability, fast response time and superior radiation tolerance. The small pixel size ($36.4\times 36.4$~$μ$m$^2$) provides high spatial resolution. Its asynchronous readout architecture is designed for high hit-rates and fast time response in triggered and trigger-less detector applications. The readout architecture is designed to stream all hit data to the multi-channel output which allows an off-sensor trigger formation and the use of hit-time information for event tagging. The sensor manufacturing has been optimised through process adaptation and special implant designs to allow the manufacturing of small electrode DMAPS on thick high-resistivity p-type Czochralski substrate. The special processing ensures excellent charge collection and charge particle detection efficiency even after a high level of radiation. Furthermore the special implant design and use of a Czochralski substrate improves the sensor's time resolution. This paper presents a summary of sensor design optimisation through process and implant choices and TCAD simulation to model the signal response. Beam and laboratory test results on unirradiated and irradiated sensors have shown excellent detection efficiency after a dose of $2\times10^{15}$ 1 MeV n$_{eq}$/cm$^{2}$. The time resolution of the sensor is measured to be $σ=2$~ns.

physics.ins-det↗

arXiv2023

Timing performance of radiation hard MALTA monolithic Pixel sensors

The MALTA family of Depleted Monolithic Active Pixel Sensor (DMAPS) produced in Tower 180 nm CMOS technology targets radiation hard applications for the HL-LHC and beyond. Several process modifications and front-end improvements have resulted in radiation hardness up to $2 \times 10^{15}~1~\text{MeV}~\text{n}_{eq}/\text{cm}^2$ and time resolution below 2 ns, with uniform charge collection efficiency across the Pixel of size $36.4 \times 36.4~μ\text{m}^2$ with a $3~μ\text{m}^2$ electrode size. The MALTA2 demonstrator produced in 2021 on high-resistivity epitaxial silicon and on Czochralski substrates implements a new cascoded front-end that reduces the RTS noise and has a higher gain. This contribution shows results from MALTA2 on timing resolution at the nanosecond level from the CERN SPS test-beam campaign of 2021.

physics.ins-det↗

arXiv2020

The HEV Ventilator

HEV is a low-cost, versatile, high-quality ventilator, which has been designed in response to the COVID-19 pandemic. The ventilator is intended to be used both in and out of hospital intensive care units, and for both invasive and non-invasive ventilation. The hardware can be complemented with an external turbine for use in regions where compressed air supplies are not reliably available. The standard modes provided include PC-A/C(Pressure Assist Control),PC-A/C-PRVC(Pressure Regulated Volume Control), PC-PSV (Pressure Support Ventilation) and CPAP (Continuous Positive airway pressure). HEV is designed to support remote training and post market surveillance via a web interface and data logging to complement the standard touch screen operation, making it suitable for a wide range of geographical deployment. The HEV design places emphasis on the quality of the pressure curves and the reactivity of the trigger, delivering a global performance which will be applicable to ventilator needs beyond theCOVID-19 pandemic. This article describes the conceptual design and presents the prototype units together with their performance evaluation.

physics.med-ph↗

arXiv2019

Calorimeters for the FCC-hh

The future proton-proton collider (FCC-hh) will deliver collisions at a center of mass energy up to $\sqrt{s}=100$ TeV at an unprecedented instantaneous luminosity of $L=3~10^{35}$ cm$^{-2}$s$^{-1}$, resulting in extremely challenging radiation and luminosity conditions. By delivering an integrated luminosity of few tens of ab$^{-1}$, the FCC-hh will provide an unrivalled discovery potential for new physics. Requiring high sensitivity for resonant searches at masses up to tens of TeV imposes strong constraints on the design of the calorimeters. Resonant searches in final states containing jets, taus and electrons require both excellent energy resolution at multi-TeV energies as well as outstanding ability to resolve highly collimated decay products resulting from extreme boosts. In addition, the FCC-hh provides the unique opportunity to precisely measure the Higgs self-coupling in the di-photon and b-jets channel. Excellent photon and jet energy resolution at low energies as well as excellent angular resolution for pion background rejection are required in this challenging environment. This report describes the calorimeter studies for a multi-purpose detector at the FCC-hh. The calorimeter active components consist of Liquid Argon, scintillating plastic tiles and Monolithic Active Pixel Sensors technologies. The technological choices, design considerations and achieved performances in full Geant4 simulations are discussed and presented. The simulation studies are focused on the evaluation of the concepts. Standalone studies under laboratory conditions as well as first tests in realistic FCC-hh environment, including pileup rejection capabilities by making use of fast signals and high granularity, have been performed. These studies have been performed within the context of the preparation of the FCC conceptual design reports (CDRs).

physics.ins-det↗

arXiv2019

Mini-MALTA: Radiation hard pixel designs for small-electrode monolithic CMOS sensors for the High Luminosity LHC

Depleted Monolithic Active Pixel Sensor (DMAPS) prototypes developed in the TowerJazz 180 nm CMOS imaging process have been designed in the context of the ATLAS upgrade Phase-II at the HL-LHC. The pixel sensors are characterized by a small collection electrode (3 $μ$m) to minimize capacitance, a small pixel size ($36.4\times 36.4$ $μ$m), and are produced on high resistivity epitaxial p-type silicon. The design targets a radiation hardness of $1\times10^{15}$ 1 MeV n$_{eq}$/cm$^{2}$, compatible with the outermost layer of the ATLAS ITK Pixel detector. This paper presents the results from characterization in particle beam tests of the Mini-MALTA prototype that implements a mask change or an additional implant to address the inefficiencies on the pixel edges. Results show full efficiency after a dose of $1\times10^{15}$ 1 MeV n$_{eq}$/cm$^{2}$.

physics.ins-det↗

arXiv2019

Experimental Determination of Proton Hardness Factors at Several Irradiation Facilities

The scheduled High Luminosity upgrade of the CERN Large Hadron Collider presents new challenges in terms of radiation hardness. As a consequence, campaigns to qualify the radiation hardness of detector sensors and components are undertaken worldwide. The effects of irradiation with beams of different particle species and energy, aiming to assess displacement damage in semiconductor devices, are communicated in terms of the equivalent 1 MeV neutron fluence, using the hardness factor for the conversion. In this work, the hardness factors for protons at three different kinetic energies have been measured by analysing the I-V and C-V characteristics of reverse biased diodes, pre- and post-irradiation. The sensors were irradiated at the MC40 Cyclotron of the University of Birmingham, the cyclotron at the Karlsruhe Institute of Technology, and the IRRAD proton facility at CERN, with the respective measured proton hardness factors being: 2.1 +/- 0.5 for 24 MeV, 2.2 +/- 0.4 for 23 MeV, and 0.62 +/- 0.04 for 23 GeV. The hardness factors currently used in these three facilities are in agreement with the presented measurements.

physics.ins-det↗

arXiv2018

Production and Integration of the ATLAS Insertable B-Layer

During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector.

physics.ins-det↗

arXiv2013

A Large Hadron Electron Collider at CERN

This document provides a brief overview of the recently published report on the design of the Large Hadron Electron Collider (LHeC), which comprises its physics programme, accelerator physics, technology and main detector concepts. The LHeC exploits and develops challenging, though principally existing, accelerator and detector technologies. This summary is complemented by brief illustrations of some of the highlights of the physics programme, which relies on a vastly extended kinematic range, luminosity and unprecedented precision in deep inelastic scattering. Illustrations are provided regarding high precision QCD, new physics (Higgs, SUSY) and electron-ion physics. The LHeC is designed to run synchronously with the LHC in the twenties and to achieve an integrated luminosity of O(100) fb$^{-1}$. It will become the cleanest high resolution microscope of mankind and will substantially extend as well as complement the investigation of the physics of the TeV energy scale, which has been enabled by the LHC.

hep-ex↗

arXiv2013

On the Relation of the LHeC and the LHC

The present note relies on the recently published conceptual design report of the LHeC and extends the first contribution to the European strategy debate in emphasising the role of the LHeC to complement and complete the high luminosity LHC programme. The brief discussion therefore focuses on the importance of high precision PDF and $α_s$ determinations for the physics beyond the Standard Model (GUTs, SUSY, Higgs). Emphasis is also given to the importance of high parton density phenomena in nuclei and their relevance to the heavy ion physics programme at the LHC.

hep-ex↗

arXiv2012

A Large Hadron Electron Collider at CERN: Report on the Physics and Design Concepts for Machine and Detector

The physics programme and the design are described of a new collider for particle and nuclear physics, the Large Hadron Electron Collider (LHeC), in which a newly built electron beam of 60 GeV, up to possibly 140 GeV, energy collides with the intense hadron beams of the LHC. Compared to HERA, the kinematic range covered is extended by a factor of twenty in the negative four-momentum squared, $Q^2$, and in the inverse Bjorken $x$, while with the design luminosity of $10^{33}$ cm$^{-2}$s$^{-1}$ the LHeC is projected to exceed the integrated HERA luminosity by two orders of magnitude. The physics programme is devoted to an exploration of the energy frontier, complementing the LHC and its discovery potential for physics beyond the Standard Model with high precision deep inelastic scattering measurements. These are designed to investigate a variety of fundamental questions in strong and electroweak interactions. The physics programme also includes electron-deuteron and electron-ion scattering in a $(Q^2, 1/x)$ range extended by four orders of magnitude as compared to previous lepton-nucleus DIS experiments for novel investigations of neutron's and nuclear structure, the initial conditions of Quark-Gluon Plasma formation and further quantum chromodynamic phenomena. The LHeC may be realised either as a ring-ring or as a linac-ring collider. Optics and beam dynamics studies are presented for both versions, along with technical design considerations on the interaction region, magnets and further components, together with a design study for a high acceptance detector. Civil engineering and installation studies are presented for the accelerator and the detector. The LHeC can be built within a decade and thus be operated while the LHC runs in its high-luminosity phase. It thus represents a major opportunity for progress in particle physics exploiting the investment made in the LHC.

physics.acc-ph↗

arXiv2007

Producing an Intense, Cool Muon Beam via e+e- Annihilation

We consider a highly unconventional approach to generating muon and antimuon bunches for a neutrino factory or muon collider: electron-positron annihilation just above muon-antimuon threshold. This approach can produce low-emittance bunches at high energy, easing the muon-cooling and acceleration challenges in such facilities. However, the small (< 1 $μ$b) useable production cross section means that extraordinary beam-power and targeting challenges would have to be met. We speculate on what this might entail.

physics.acc-ph↗