arXiv subjects

Rabia Sultana

Publications and source records attributed to Rabia Sultana.

15 recordsLinked to original sources

arXiv2021

Modeling of Magneto-Conductivity of Bismuth Selenide -- A Topological Insulator

We report the magneto-conductivity analysis of Bi2Se3 single crystal at different temperatures in a magnetic field range of 14Tesla. The single crystals are grown by the self-flux method and characterized through X-ray diffraction, Scanning Electron Microscopy, and Raman Spectroscopy. The single crystals show magnetoresistance (MR) of around 380 percent at a magnetic field of 14T and a temperature of 5K. The Hikami Larkin Nagaoka (HLN) equation has been used to fit the magneto-conductivity (MC) data. However, the HLN fitted curve deviates at higher magnetic fields above 1 Tesla, suggesting that the role of surface driven conductivity suppresses with an increasing magnetic field. This article proposes a speculative model comprising of surface-driven HLN and added quantum diffusive and bulk carriers driven classical terms. The model successfully explains the MC of the Bi2Se3 single crystal at various temperatures (5 to 200K) and applied magnetic fields (up to 14Tesla).

cond-mat.mtrl-sci↗

arXiv2020

Comprehensive Analysis for the High Field Magneto-conductivity of Bi2Te3 Single Crystal

Here, we report the magneto-conductivity (up to 14Tesla and down to 5K) analysis of Bi2Te3 single-crystal. A sharp magneto-conductivity (MC) rise (inverted v-type cusp) is observed near H=0 due to the weak antilocalization (WAL) effect, while a linear curve is observed at higher fields. We account for magneto-conductivity (MC) over the entire range of applied magnetic fields of up to 14Tesla and temperatures from 100K to 5K in a modified HLN modelling (addition of quadratic (BH2) through quantum and classical components involvement. The additional term BH2 reveals a gradual change of a (HLN parameter) from -0.421(6) to -0.216(1) as the temperature increases from 5 to 100K. The phase coherence length Lphi obtained from both conventional and modified modelling decreased with increasing temperature but remains more protracted than the mean free path (L) of electrons. It shows the quantum phase coherence effect dominates at high temperature.

cond-mat.mtrl-sci↗

arXiv2019

Crystal Growth and basic transport and magnetic properties of MnBi2Te4

We report successful growth of magnetic topological insulator (MTI) MnBi2Te4. The heating schedule basically deals with growth of the crystal from melt at 900C and very slow cooling (1C/hr) to around 600C with 24 hours hold time, followed by cooling to room temperature. Our detailed, PXRD Reitveld analysis showed that the resultant crystal is dominated mainly by MnBi2Te4 and minor phases of Bi2Te3 and MnTe. The transport measurements showed a step like behavior at around 150K followed by cusp like structure in resistivity at around 25K (TP) due reported anti-ferromagnetic ordering of Mn. Both the resistivity transitions are seen clearly in dR/dT measurements at 150K and 20K respectively. The 25K transition of the compound is also seen in magnetic susceptibility. Low temperature (5K) magnetoresistance (MR) in applied field of up to 6 Tesla exhibited negative ve MR below 3 Tesla and +ve for higher fields. Also, seen are steps in MR below one Tesla. The studied MnBi2Te4 MTI crystal could be a possible candidate for Quantum Anomalous Hall (QAH) effect.

cond-mat.mtrl-sci↗

arXiv2019

Structural, Surface Morphology and Magneto-Transport properties of Self Flux Grown Eu Doped Bi2Se3 Single Crystal

Here, we report the effect of europium (Eu) doping in Bi2Se3 topological insulator (TI) by using different characterization techniques viz. X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive X-ray analysis (EDXA) and magneto-transport measurements. Temperature dependent electrical resistivity curves revealed a metallic behaviour both in the presence and absence of applied magnetic field. Magneto-transport measurements showed a decrease in the magneto-resistance (MR) value of the Eu0.1Bi1.9Se3 sample (32% at 5K) in comparison to the pure Bi2Se3 sample (80% at 5K). For, Eu0.1Bi1.9Se3 sample, a complex crossover between WL and WAL phenomenon was observed at lower applied magnetic fields, whereas the same was absent in case of the pristine one. Further, HLN (Hikami Larkin Nagaoka) fitted magneto-conductivity (MC) analysis revealed a competing weak anti localization (WAL) and weak localization (WL) behaviour. Summarily, in the present work we study the structural, surface morphology and magneto-transport properties of as grown Eu0.1Bi1.9Se3 single crystals.

cond-mat.mtrl-sci↗

arXiv2019

Flux Free Single Crystal Growth and Detailed Physical Property Characterization of Bi1-xSbx (x = 0.05, 0.1 and 0.15) Topological Insulator

Here, we report the crystal growth, physical and transport properties of Bi1-xSbx (x = 0.05, 0.1 and 0.15) topological insulator. Single crystals of Bi1-xSbx (x = 0.05, 0.1 and 0.15) were grown by melting bismuth and antimony together using the facile self flux method. The XRD measurements displayed highly indexed 00l lines and confirmed the crystalline nature as well as the rhombohedral structure of the Bi1-xSbx (x = 0.05, 0.1 and 0.15) crystals. Raman spectroscopy measurements for Bi1-xSbx system revealed four peaks within the spectral range of 10 to 250 cm-1 namely A1g and Eg modes corresponding to Bi-Bi and Sb-Sb vibrations. Scanning electron microscopy (SEM) and energy dispersive Temperature dependent electrical resistivity curves with and without applied magnetic field exhibited a metallic behaviour and linear non-saturating magneto-resistance (MR) respectively for all the antimony (Sb) concentrations of x = 0.05, 0.1 and 0.15. The lowest Sb concentration sample with x = 0.05 (Bi0.95Sb0.05) exhibited the highest MR value of about 1400%, followed by x = 0.1 and 0.15 samples (Bi0.9Sb0.1 and Bi0.85Sb0.05) with MR values reaching up to 500% and 110% respectively at 2K and 6Tesla applied field. The magneto-conductivity (MC) is fitted to the HLN (Hikami Larkin Nagaoka) equation and it is found that the charge conduction mechanism is mainly dominated by WAL (weak anti-localization) along with a small contribution from WL (weak localization) effect. Summarily, the short letter discusses the synthesis, interesting transport and magneto-transport properties of Bi1-xSbx (x = 0.05, 0.1 and 0.15), which could be useful in understanding the fascinating properties of topological insulators and their technological applications.

cond-mat.mtrl-sci↗

arXiv2018

Growth, Characterization and High Field Magneto-Conductivity of Co0.1Bi2Se3 Topological Insulator

We report the crystal growth as well as transport properties of Co added Bi2Se3 single crystals. The values of the lattice parameters a and b for Co added sample were observed to increase as compared to the pure Bi2Se3. The Raman spectroscopy displayed higher Raman shift of corresponding vibrational modes for Co0.1Bi2Se3, and the resistivity curves with and without applied magnetic field shows a metallic behaviour. Both the crystals were subjected to magneto-resistance (MR) measurements under applied fields of 14Tesla. The value of MR is found to decrease from about 380 (5K, 14 Tesla) for Bi2Se3 to 200 degree for Co0.1Bi2Se3. To elaborate the transport properties of pure and Co added Bi2Se3 crystals, the magneto-conductivity is fitted to the HLN (Hikami Larkin Nagaoka) equation and it is found that the charge conduction is mainly dominated by surface driven WAL (weak anti-localization) with negligible bulk WL (weak localization) contribution in both crystals alike. The MH curves of Co0.1Bi2Se3 crystal at different temperatures displayed a combination of both ferromagnetic and diamagnetic behaviour. On the other hand, the Electron Paramagnetic Resonance (EPR) revealed that pure Bi2Se3 is diamagnetic whereas, Co orders ferro-magnetically with resonating field around 3422Oe at room temperature.

cond-mat.mtrl-sci↗

arXiv2018

High Field Magneto-Conductivity Analysis of Bi2Se3 Single Crystal

We report the high field (up to 14Tesla) magneto-conductivity analysis of Bi2Se3 topological insulator grown via the self flux method. The detailed experimental investigations including crystal growth as well as the electrical, thermal and spectroscopic characterizations of the resultant Bi2Se3 single crystal are already reported by some of us. The current letter deals with high field magneto-conductivity analysis in terms of Hikami Larkin Nagaoka (HLN) model, which revealed that the electronic conduction is dominated by both surface states driven weak anti localization (WAL), as well the bulk WL (weak localization) states. Further, by applying the HLN equation we have extracted the fitting parameters i.e., phase coherence length and the pre-factor. The HLN equation exhibited values of [pre factor close to -1.0, indicating both WAL and WL contributions. On the other hand, the extracted phase coherence length is seen to decrease from 11.125 nm to 5.576 nm as the temperature is increased from 5K to 200K respectively. Summarily, the short letter discusses primarily the temperature dependent magneto-conductivity analysis of pristine Bi2Se3 single crystal by the HLN model.

cond-mat.mtrl-sci↗

arXiv2018

Unexplored photoluminescence from bulk and mechanically exfoliated few layers of Bi2Te3

We report the exotic photoluminescence (PL) behaviour of 3D topological insulator Bi2Te3 single crystals grown by customized self-flux method and mechanically exfoliated few layers (18 plus minus 2 nm)/thin flakes obtained by standard scotch tape method from as grown Bi2Te3 crystals.The experimental PL studies on bulk single crystal and mechanically exfoliated few layers of Bi2Te3 evidenced a broad red emission in the visible region. These findings are in good agreement with our theoretical results obtained using the ab initio density functional theory framework.

cond-mat.mtrl-sci↗

arXiv2018

Hikami-Larkin-Nagaoka (HLN) treatment of the Magneto Conductivity of Bi2Te3 Topological Insulator

We report the magneto-conductivity analysis at different temperatures under magnetic field of up to 5Tesla of a well characterized Bi2Te3 crystal. Details of crystal growth and various physical properties including high linear magneto resistance are already reported by some of us. To elaborate upon the transport properties of Bi2Te3 crystal, the magneto conductivity is fitted to the known HLN (Hikami Larkin Nagaoka) equation and it is found that the conduction mechanism is dominated by both surface driven WAL (weak anti localization) and the bulk WL states. The value of HLN equation coefficient signifying the type of localization (WL, WAL or both WL and WAL) falls within the range of -0.5 to -1.5. In our case, the low field (0.25Tesla) fitting of studied crystal exhibited value close to -0.86 for studied temperatures of up to 50K, indicating both WAL and WL contributions. The phase coherence length is found to decrease from 98.266 to 40.314nm with increasing temperature. Summarily, the short letter reports the fact that bulk Bi2Te3 follows the HLN equation and quantitative analysis of the same facilitates to know the quality of studied crystal in terms of WAL to WL contributions and thus the surface to bulk conduction ratio.

cond-mat.mtrl-sci↗

arXiv2018

Crystal Growth and Characterization of Bulk Sb2Te3Topological Insulator

The Sb2Te3 crystals are grown using the conventional self flux method via solid state reaction route, by melting constituent elements (Sb and Te) at high temperature (850 C), followed by slow cooling (2 C per hour).The weak anti localization (WAL) related low field (2 Tesla) magneto-conductance at low temperatures (2.5 K and 20 K) has been analysed and discussed using the Hikami- Larkin - Nagaoka (HLN) model. Summarily, the short letter reports an easy and versatile method for crystal growth of bulk Sb2Te3 topological insulator (TI) and its brief physical property characterization.

cond-mat.mtrl-sci↗

arXiv2017

High Field (up to 140kOe) Angle Dependent Magneto Transport of Bi2Te3 Single Crystals

We report the angle dependent high field (up to 140kOe) magneto transport of Bi2Te3 single crystals, a well-known topological insulator. The crystals were grown from melt of constituent elements via solid state reaction route by self-flux method. Details of crystal growth along with their brief characterization up to 5 Tesla applied field was reported by some of us recently [J. Magn. Mag. Mater. 428, 213 (2017)]. The angle dependence of the magneto-resistance (MR) of Bi2Te3 follows the cos Theta function i.e., MR is responsive, when the applied field is perpendicular (tilt angle Theta = o and/or 180) to the transport current. The low field (10 kOe) MR showed the signatures of weak anti localization (WAL) character with typical cusp near origin at 5 K. Further, the MR is linear right up to highest applied field of 140 kOe. The large positive MR are observed up to high temperatures and are above 250 and 150 percent at 140 kOe in perpendicular fields at 50 K and 100 K respectively. Heat capacity CP(T) measurements revealed the value of Debye temperature to be 135 K. ARPES (angle resolved photoemission spectroscopy) data clearly showed that the bulk Bi2Te3 single crystal consists of a single Dirac cone.

cond-mat.mtrl-sci↗

arXiv2017

Novel solid state vacuum quartz encapsulated growth of p-Terphenyl: the parent High Tc Oraganic Superconductor (HTOS)

We report an easy and versatile route for the synthesis of the parent phase of newest superconducting wonder material i.e. p-Terphenyl. Doped p-terphenyl has recently shown superconductivity with transition temperature as high as 120K. For crystal growth, the commercially available p-Terphenyl powder is pelletized, encapsulated in evacuated (10-4 Torr) quartz tube and subjected to high temperature (260C) melt followed by slow cooling at 5C/hour. Simple temperature controlled heating furnace is used during the process. The obtained crystal is one piece, shiny and plate like. Single crystal surface XRD (X-ray Diffraction) showed unidirectional (00l) lines, indicating that the crystal is grown along c-direction. Powder XRD of the specimen showed that as grown p-Terphenyl is crystallized in monoclinic structure with space group P21/a space group, having lattice parameters a = 8.08(2) A, b = 5.62(5) A and c= 13.58(3) A. Scanning electron microscopy (SEM) pictures of the crystal showed clear layered slab like growth without any visible contamination from oxygen. Characteristic reported Raman active modes related to C-C-C bending, C-H bending, C-C stretching and C-H stretching vibrations are seen clearly for the studied p-Terphenyl crystal. The physical properties of crystal are yet underway. The short letter reports an easy and versatile crystal growth method for obtaining quality p-terphenyl. The same growth method may probably be applied to doped p-terphenyl and to subsequently achieve superconductivity to the tune of as high 120K for the newest superconductivity wonder i.e., High Tc Oraganic Superconductor (HTOS).

cond-mat.supr-con↗

arXiv2017

Crystal Growth and Magneto-transport of Bi2Se3 Single crystals

In this letter, we report growth and characterization of bulk Bi2Se3 single crystals. The studied Bi2Se3 crystals are grown by self flux method through solid state reaction from high temperature (950C) melt of constituent elements and slow cooling (2C/hour). The resultant crystals are shiny and grown in [00l] direction, as evidenced from surface XRD. Detailed Reitveld analysis of PXRD (powder x-ray diffraction) of the crystals showed that these are crystallized in rhombohedral crystal structure with space group of R3m (D5) and the lattice parameters are a = 4.14(2)A, b = 4.14 (2) A and c = 28.7010(7) A. Temperature versus resistivity (R-T) plots revealed metallic conduction down to 2K, with typical room temperature resistivity (R300K) of around 0.53 mohm-cm and residual resistivity of 0.12 mohm-cm. Resistivity under magnetic field ] measurements exhibited large +Ve magneto resistance right from 2K to 200K. Isothermal magneto resistance [RH] measurements at 2K, 100K and 200K exhibited magneto resistance (MR) of up to 240, 130 and 60 percent respectively at 14 Tesla. Further the MR plots are non saturating and linear with field at all temperature. At 2K the MR plots showed clear quantum oscillations at above say 10 Tesla applied field. Also the Kohler plots i.e., were seen consolidating on one plot. Interestingly, the studied Bi2Se3 single crystal exhibited the Shubnikov-de Haas oscillations (SdH) at 2K under different applied magnetic fields ranging from 4Tesla to 14 Tesla

cond-mat.supr-con↗

arXiv2017

Electrical, Thermal and Spectroscopic Characterization of Bulk Bi2Se3 Topological Insulator

We report electrical (angular magneto-resistance, and Hall), thermal (heat capacity) and spectroscopic (Raman, x-ray photo electron, angle resolved photo electron) characterization of bulk Bi2Se3 topological insulator, which is being is grown by self flux method through solid state reaction from high temperature (950C) melt and slow cooling (2C/hour) of constituent elements. Bi2Se3 exhibited metallic behaviour down to 5K. Magneto transport measurements revealed linear up to 400% and 30% MR at 5K under 14 Tesla field in perpendicular and parallel field direction respectively. We noticed that the magneto-resistance (MR) of Bi2Se3 is very sensitive to the angle of applied field. MR is maximum when the field is normal to the sample surface, while it is minimum when the field is parallel. Hall coefficient (RH) is seen nearly invariant with negative carrier sign down to 5K albeit having near periodic oscillations above 100K. Heat capacity (Cp) versus temperature plot is seen without any phase transitions down to 5K and is well fitted (Cp = gammaT + betaT3) at low temperature with calculated Debye temperature (ThetaD) value of 105.5K. Clear Raman peaks are seen at 72, 131 and 177 cm-1 corresponding to A1g1, Eg2 and A1g2 respectively. Though, two distinct asymmetric characteristic peak shapes are seen for Bi 4f7/2 and Bi 4f5/2, the Se 3d region is found to be broad displaying the overlapping of spin - orbit components of the same. Angle-resolved photoemission spectroscopy (ARPES) data of Bi2Se3 revealed distinctly the bulk conduction bands (BCB), surface state (SS), Dirac point (DP) and bulk valence bands (BVB) and 3D bulk conduction signatures are clearly seen. Summarily, host of physical properties for as grown Bi2Se3 crystal are reported here.

cond-mat.str-el↗

arXiv2017

Unusual non saturating Giant Magneto-resistance in single crystalline Bi2Te3 topological insulator

We report synthesis, structural details and electrical transport properties of topological insulator Bi2Te3. The single crystalline specimens of Bi2Te3 are obtained from high temperature (950C) melt and slow cooling (2C/hour). The resultant crystals were shiny, one piece (few cm) and of bright silver color. The Bi2Te3 crystal is found to be perfect with clear [00l] alignment. The powder XRD pattern being carried out on crushed crystals showed that Bi2Te3 crystallized in R3m symmetry with a = b = 4.3866(2) A, c = 30.4978(13) A and Gamma = 120degree. The Bi position is refined to (0, 0, 0.4038 (9)) at Wyckoff position 6c and of Te are (0, 0, 0) at Wyckoff position 3a and at (0, 0, 0.2039(8)) at 6c. Ambient pressure and low temperature (down to 2K) electrical transport measurements revealed metallic behavior. Magneto transport measurements under magnetic field showed huge non saturating magneto resistance (MR) reaching up to 250% at 2.5K and under 50KOe field. Summarily, the short communication clearly demonstrates that Bi2Te3 topological insulator exhibit non-saturating large positive MR at low temperature of say below 10K. The non saturating MR is seen right up to room temperature albeit with much decreased magnitude. Worth mentioning is the fact that these crystals are bulk in nature and hence the anomalous MR is clearly an intrinsic property and not due to the size effect as reported for nano-wires or thin films of the same.

cond-mat.str-el↗