arXiv subjects

S. Posen

Publications and source records attributed to S. Posen.

At least 37 records · Page 2Linked to original sources

arXiv2022

Tests Of The Extended Range SRF Cavity Tuners For The LCLS-II-HE Project*

The LCLS-II HE superconducting linac can produce multi-energy beams by supporting multiple undulator lines simultaneously. This could be achieved by using the cavity SRF tuner in the off-frequency detune mode. This off-frequency operation method was tested in the verification cryomodule (vCM) and CM 1 at Fermilab at 2 K. In both cases, the tuners achieved a frequency shift of -565$\pm$80 kHz. This study will discuss cavity frequency during each step as it is being assembled in the cryomodule string and finally when it is being tested at 2 K. Tracking the cavity frequency helped enable the tuners to reach this large frequency shift. The specific procedures of tuner setting during assembly will be presented.

physics.acc-ph↗

arXiv2022

Multi-modal electron microscopy study on decoherence sources and their stability in Nb based superconducting qubit

Niobium is commonly used for superconducting quantum systems as readout resonators, capacitors, and interconnects. The coherence time of the superconducting qubits is mainly limited by microwave dissipation attributed to two-level system defects at interfaces, such as the Nb/Si and Nb/air interface. One way to improve the Nb/air interface quality is by thermal annealing, as shown by extensive studies in 3D superconducting radio frequency (SRF) cavities. However, it is unclear how the microstructure and chemistry of the interface structures change during heat treatment. To address this knowledge gap, we comprehensively characterized Nb films deposited on Si wafers by physical vapor deposition, including (1) an Nb film from a transmon and (2) an Nb film without any patterning step, using an aberration-corrected transmission electron microscope. Both Nb films exhibit columnar growth with strong [110] textures. There is a double layer between the Nb film and Si substrate, which are amorphous niobium silicides with different Nb and Si concentrations. After in-situ heating of the heterostructure at 360°C inside the microscope, the composition of the double layers at the Nb-Si interface remains almost the same despite different thickness changes. The initial amorphous niobium oxide layer on Nb surface decomposes into face-centered cubic Nb nanograins in the amorphous Nb-O matrix upon heating.

cond-mat.mtrl-sci↗

arXiv2022

Plasma Processing for In-Situ Field Emission Mitigation of Superconducting Radiofrequency (SRF) Cryomodules

Field emission (FE) is one of the main limiting factors of superconducting radio-frequency (SRF) cavities operating in accelerators and it occurs whenever contaminants, like dust, metal flakes or even absorbates, are present on the surface of the cavity high electric field region. Field emission reduces the maximum achievable accelerating field and generates free electrons that may interact with the beam, damage or activate the beamline. One practical method that can be used to mitigate this problem is in-situ plasma cleaning, or plasma processing. The development of a processing that can be applied in-situ is extremely advantageous, since it enables the recovery of the cryomodule performance without the need of disassembling the whole cryomodule, which is an extremely expensive and time-consuming process. On the other hand, plasma processing only requires the cryomodule warm-up to room-temperature and the subsequent processing of the contaminated cavities. The entire process is reasonably quick and involves a limited number of personnel. For these reasons we would like to advocate for continuing to invest in the R\&D of plasma processing to optimize its applicability in cryomodules and for extending the technique to other frequency ranges and cavities geometries.

physics.acc-ph↗

arXiv2022

Future Collider Options for the US

The United States has a rich history in high energy particle accelerators and colliders -- both lepton and hadron machines, which have enabled several major discoveries in elementary particle physics. To ensure continued progress in the field, U.S. leadership as a key partner in building next generation collider facilities abroad is essential; also critically important is the exploring of options to host a future collider in the U.S. The "Snowmass" study and the subsequent Particle Physics Project Prioritization Panel (P5) process provide the timely opportunity to develop strategies for both. What we do now will shape the future of our field and whether the U.S. will remain a world leader in these areas. In this white paper, we briefly discuss the US engagement in proposed collider projects abroad and describe future collider options for the U.S. We also call for initiating an integrated R\&D program for future colliders.

hep-ex↗

arXiv2022

Higgs-Energy LEptoN (HELEN) Collider based on advanced superconducting radio frequency technology

This Snowmass 2021 contributed paper discusses a Higgs-Energy LEptoN (HELEN) $e^+e^-$ linear collider based on advances superconducting radio frequency technology. The proposed collider offers cost and AC power savings, smaller footprint (relative to the ILC), and could be built at Fermilab with an Interaction Region within the site boundaries. After the initial physics run at 250 GeV, the collider could be upgraded either to higher luminosity or to higher (up to 500 GeV) energies. If the ILC could not be realized in Japan in a timely fashion, the HELEN collider would be a viable option to build a Higgs factory in the U.S.

physics.acc-ph↗

arXiv2022

Nb3Sn Superconducting Radiofrequency Cavities: a Maturing Technology for Particle Accelerators and Detectors

Nb3Sn superconducting radiofrequency (SRF) cavities have substantial potential for enabling new performance capabilities for particle accelerators for high energy physics (HEP), as well as for RF cavity-based detectors for dark matter, gravitational waves, and other quantum sensing applications. Outside of HEP, Nb3Sn SRF cavities can also benefit accelerators for nuclear physics, basic energy sciences, and the industry. In this contribution to Snowmass 2021, we overview the potential, status, and outlook of Nb3Sn SRF cavities.

physics.acc-ph↗

arXiv2021

LCLS-II-HE verification cryomodule high gradient performance and quench behavior

An 8-cavity, 1.3 GHz, LCLS-II-HE cryomodule was assembled and tested at Fermilab to verify performance before the start of production. Its cavities were processed with a novel nitrogen doping treatment to improve gradient performance. The cryomodule was tested with a modified protocol to process sporadic quenches, which were observed in LCLS-II production cryomodules and are attributed to multipacting. Dedicated vertical test experiments support the attribution to multipacting. The verification cryomodule achieved an acceleration voltage of 200 MV in continuous wave mode, corresponding to an average accelerating gradient of 24.1 MV/m, significantly exceeding the specification of 173 MV. The average Q0 (3.0x10^10) also exceeded its specification (2.7x10^10). After processing, no field emission was observed up to the maximum gradient of each cavity. This paper reviews the cryomodule performance and discusses operational issues and mitigations implemented during the several month program.

physics.acc-ph↗

arXiv2021

Development of a cryocooler conduction-cooled 650 MHz SRF cavity operating at ~10 MV/m cw accelerating gradient

SRF cavities for particle acceleration are conventionally operated immersed in a bath of liquid helium at 4.2 K and below. Although this cooling configuration is practically and economically viable for large scientific accelerator installations, it may not be so for smaller accelerators intended for industrial applications such as the treatment of wastewater, sludge, flue gases, etc. In this paper, we describe a procedure to operate SRF cavities without liquid helium that can be used to construct electron-beam sources for industrial applications of electron irradiation (1-10 MeV electron energy). In this procedure, an elliptical single-cell 650 MHz niobium-tin coated niobium cavity is coupled to a closed-cycle 4 K cryocooler using high purity aluminum thermal links. The cryocooler conductively extracts heat (RF dissipation) from the cavity without requiring liquid helium around the cavity. We present construction details of this cryocooler conduction-cooling technique and systematic experiments that have demonstrated ~10 MV/m cw gradient on the cavity. By straightforward scaling up the cavity length and number of cryocoolers, the technique will provide the complete range of 1-10 MeV electron energy for industrial applications.

physics.acc-ph↗

arXiv2020

Advances in Nb3Sn superconducting radiofrequency cavities towards first practical accelerator applications

Nb3Sn is a promising next-generation material for superconducting radiofrequency cavities, with significant potential for both large scale and compact accelerator applications. However, so far, Nb3Sn cavities have been limited to cw accelerating fields <18 MV/m. In this paper, new results are presented with significantly higher fields, as high as 24 MV/m in single cell cavities. Results are also presented from the first ever Nb3Sn-coated 1.3 GHz 9-cell cavity, a full-scale demonstration on the cavity type used in production for the European XFEL and LCLS-II. Results are presented together with heat dissipation curves to emphasize the potential for industrial accelerator applications using cryocooler-based cooling systems. The cavities studied have an atypical shiny visual appearance, and microscopy studies of witness samples reveal significantly reduced surface roughness and smaller film thickness compared to typical Nb3Sn films for superconducting cavities. Possible mechanisms for increased maximum field are discussed as well as implications for physics of RF superconductivity in the low coherence length regime. Outlook for continued development is presented.

physics.acc-ph↗

arXiv2020

First demonstration of a cryocooler conduction cooled superconducting radiofrequency cavity operating at practical cw accelerating gradients

We demonstrate practical accelerating gradients on a superconducting radiofrequency (SRF) accelerator cavity with cryocooler conduction cooling, a cooling technique that does not involve the complexities of the conventional liquid helium bath. A design is first presented that enables conduction cooling an elliptical-cell SRF cavity. Implementing this design, a single cell 650 MHz Nb3Sn cavity coupled using high purity aluminum thermal links to a 4 K pulse tube cryocooler generated accelerating gradients up to 6.6 MV/m at 100% duty cycle. The experiments were carried out with the cavity-cryocooler assembly in a simple vacuum vessel, completely free of circulating liquid cryogens. We anticipate that this cryocooling technique will make the SRF technology accessible to interested accelerator researchers who lack access to full-stack helium cryogenic systems. Furthermore, the technique can lead to SRF based compact sources of high average power electron beams for environmental protection and industrial applications. A concept of such an SRF compact accelerator is presented.

physics.ins-det↗

arXiv2020

Development and Understanding of Nb$_3$Sn films for radiofrequency applications through a sample-host 9-cell cavity

Nb$_3$Sn is a promising advanced material under development for superconducting radiofrequency (SRF) cavities. Past efforts have been focused primarily on small development-scale cavities, but large, often multi-celled cavities, are needed for particle accelerator applications. In this work, we report on successful Nb$_3$Sn coatings on Nb in a 1 m-long 9-cell Nb sample-host cavity at Fermilab. The geometry of the first coating with only one Sn source made it possible to study the influence of Sn flux on the microstructure. Based on these results, we postulate a connection between recently observed anomalously large thin grains and uncovered niobium spots observed in the past by other authors [Trenikhina 2018]. A phenomenological model to explain how these anomalously large grains could form is proposed. This model is invoked to provide possible explanations for literature results from several groups and to guide key process parameters to achieve uniform vapor-diffusion coatings, when applied to complex structures as the multi-cell cavity under study.

physics.app-ph↗

arXiv2019

Three-dimensional superconducting resonators at $T < 20$ mK with the photon lifetime up to $τ=2$ seconds

Very high quality factor superconducting radio frequency cavities developed for accelerators can enable fundamental physics searches with orders of magnitude higher sensitivity, as well as offer a path to a 1000-fold increase in the achievable coherence times for cavity-stored quantum states in the 3D circuit QED architecture. Here we report the first measurements of multiple accelerator cavities of $f_0=$1.3, 2.6, 5 GHz resonant frequencies down to temperatures of about 10~mK and field levels down to a few photons, which reveal record high photon lifetimes up to 2 seconds, while also further exposing the role of the two level systems (TLS) in the niobium oxide. We also demonstrate how the TLS contribution can be greatly suppressed by the vacuum heat treatments at 340-450$^\circ$C.

quant-ph↗

arXiv2019

Impact of high Q on ILC250 upgrade for record luminosities and path toward ILC380

In this paper, we address the possibility of upgrading the ILC250 luminosity to $8.1 \times 10^{34}$, so that with the polarization feature, the effective luminosity will be $2.0 \times 10^{35}$ to compete with the FCC-ee luminosity and two detectors. The additional cost of the higher luminosity option will be about 2.2 B ILCU. The total cost for the ILC high luminosity machine will therefore be about 7.7 B versus FCC-ee 10.5 B. The AC power (267 MW) to operate the ILC luminosity upgrade will also be less than the AC power for FCC-ee (300 MW). Even with a modest quality factor Q of $1 \times 10^{10}$ for SRF cavities, the total cost of the upgrade will be 2.5 B ILCU additional over ILC250 baseline. We expect that, if approved, ILC250 will first be built at the baseline luminosity, operated for many years at this luminosity, and later upgraded to the high luminosity option. A significant part (RF power and cryo-power) of the additional cost for the luminosity upgrade overlaps with the expected additional costs for anticipated energy upgrade paths. A second ILC upgrade discussed in this paper will be to the higher energy Top Factory at 380 GeV. We also estimate the additional cost of this upgrade (1.5 B ILCU).

physics.acc-ph↗

arXiv2019

Ultra-Low Surface Resistance via Vacuum Heat Treatment of Superconducting Radiofrequency Cavities

We report on an effort to improve the performance of superconducting radiofrequency cavities by the use of heat treatment in a temperature range sufficient to dissociate the natural surface oxide. We find that the residual resistance is significantly decreased, and we find an unexpected reduction in the BCS resistance. Together these result in extremely high quality factor values at relatively large accelerating fields Eacc ~20 MV/m: Q0 of 3-4x10^11 at <1.5 K and Q0 ~5x10^10 at 2.0 K. In one cavity, measurements of surface resistance versus temperature showed an extremely small residual resistance of just 0.63+/-0.06 nOhms at 16 MV/m. SIMS measurements confirm that the oxide was significantly dissociated, but they also show the presence of nitrogen after heat treatment. We also present studies of surface oxidation via exposure to air and to water, as well as the effects of very light surface removal via HF rinse. The possibilities for applications and the planned future development are discussed.

physics.acc-ph↗

arXiv2019

Critical Fields of Nb$_3$Sn Prepared for Superconducting Cavities

Nb$_3$Sn is currently the most promising material other than niobium for future superconducting radiofrequency cavities. Critical fields above 120 mT in pulsed operation and about 80 mT in CW have been achieved in cavity tests. This is large compared to the lower critical field as derived from the London penetration depth, extracted from low field surface impedance measurements. In this paper direct measurements of the London penetration depth from which the lower critical field and the superheating field are derived are presented. The field of first vortex penetration is measured under DC and RF fields. The combined results confirm that Nb$_3$Sn cavities are indeed operated in a metastable state above the lower critical field but are currently limited to a critical field well below the superheating field.

physics.acc-ph↗

arXiv2018

The Role of Magnetic Flux Expulsion to Reach Q0>3x10^10 in SRF Cryomodules

When a superconducting radiofrequency cavity is cooled through its critical temperature, ambient magnetic flux can become "frozen in" to the superconductor, resulting in degradation of the quality factor. This is especially problematic in applications where quality factor is a cost driver, such as in the CW linac for LCLS-II. Previously, it had been unknown how to prevent flux from being trapped during cooldown in bulk niobium cavities, but recent R&D studies showed near-full flux expulsion can be achieved through high temperature heat treatment and cooling cavities through the superconducting transition with a spatial thermal gradient over the surface. In this paper, we describe the first accelerator implementation of these procedures, in cryomodules that are currently being produced for LCLS-II. We compare the performance of cavities under different conditions of heat treatment and thermal gradient during cooldown, showing a substantial improvement in performance when both are applied, enabling cryomodules to reach and, in many cases, exceed a Q0 of ~3x10^10.

physics.acc-ph↗

arXiv2018

Accelerating fields up to 49 MV/m in TESLA-shape superconducting RF niobium cavities via 75C vacuum bake

In this paper we present the discovery of a new surface treatment applied to superconducting radio frequency (SRF) niobium cavities, leading to unprecedented accelerating fields of 49 MV/m in TESLA-shaped cavities, in continuous wave (CW); the corresponding peak magnetic fields are the highest ever measured in CW, about 210 mT. For TESLA-shape cavities the maximum quench field ever achieved was ~45 MV/m - reached very rarely- with most typical values being below 40 MV/m. These values are reached for niobium surfaces treated with electropolishing followed by the so called mild bake, a 120C vacuum bake (for 48 hours for fine grain and 24 hours for large grain surfaces). We discover that the addition during the mild bake of a step at 75C for few hours, before the 120C, increases systematically the quench fields up to unprecedented values of 49 MV/m. The significance of the result lays not only in the relative improvement, but in the proof that niobium surfaces can sustain and exceed CW radio frequency magnetic fields much larger than Hc1, pointing to an extrinsic nature of the current field limitations, and therefore to the potential to reach accelerating fields well beyond the current state of the art.

physics.acc-ph↗

arXiv2018

The Effect of Mechanical Cold Work on the Magnetic Flux Expulsion of Niobium

Expulsion of ambient flux has been shown to be crucial to obtain high quality factors in bulk niobium SRF cavities. However, there remain many questions as to what properties of the niobium material determine its flux expulsion behavior. In this paper, we present first results from a new study of two cavities that were specially fabricated to study flux expulsion. Both cavities were made from large grain ingot niobium slices, one of which had its slices rolled prior to fabrication, and none these slices were annealed prior to measurement. Expulsion measurements indicate that a dense network of grain boundaries is not necessary for a cavity to have near-complete flux trapping behavior up to large thermal gradients. The results also contribute to a body of evidence that cold work is a strong determinant of flux expulsion behavior in SRF-grade niobium.

physics.acc-ph↗