arXiv subjects

Scott B. Papp

Publications and source records attributed to Scott B. Papp.

At least 91 records · Page 5Linked to original sources

arXiv2018

Deuterated silicon nitride photonic devices for broadband optical frequency comb generation

We report and characterize low-temperature, plasma-deposited deuterated silicon nitride thin films for nonlinear integrated photonics. With a peak processing temperature less than 300$^\circ$C, it is back-end compatible with pre-processed CMOS substrates. We achieve microresonators with a quality factor of up to $1.6\times 10^6 $ at 1552 nm, and $>1.2\times 10^6$ throughout $λ$ = 1510 -- 1600 nm, without annealing or stress management. We then demonstrate the immediate utility of this platform in nonlinear photonics by generating a 1 THz free spectral range, 900-nm-bandwidth modulation-instability microresonator Kerr comb and octave-spanning, supercontinuum-broadened spectra.

physics.optics↗

arXiv2018

Downsampling of optical frequency combs

We demonstrate repetition-rate downsampling of optical frequency combs by way of pulse gating. The reduced repetition rate enables increased pulse energy, facilitating efficient spectral broadening and f-2f interferometry. To explore the technique, we downsample a 250 MHz repetition-rate comb to 25 MHz and detect the carrier-envelope offset frequency of the downsampled pulse train. We investigate the effects of pulse gating on the noise properties of the pulse train and the limitations of the technique by characterizing the phase-noise spectrum of the downsampled comb and deliberately imposing timing jitter on the pulse gate. We show that, up to an expected reduction modulo the new repetition rate, downsampling neither shifts nor introduces noise to the carrier-envelope offset frequency of the comb above the level of several microhertz. Additionally, we discuss the effect of downsampling on the spectrum of intensity fluctuations of the optical pulse train. Finally, we discuss some practical considerations relevant for the application of the technique to frequency combs with repetition rates in the 10 GHz range and higher.

physics.optics↗

arXiv2018

Mid-infrared frequency comb generation via cascaded quadratic nonlinearities in quasi-phase-matched waveguides

We experimentally demonstrate a simple configuration for mid-infrared (MIR) frequency comb generation in quasi-phase-matched lithium niobate waveguides using the cascaded-$χ^{(2)}$ nonlinearity. With nanojoule-scale pulses from an Er:fiber laser, we observe octave-spanning supercontinuum in the near-infrared with dispersive-wave generation in the 2.5--3 $\textμ$m region and intra-pulse difference-frequency generation in the 4--5 $\textμ$m region. By engineering the quasi-phase-matched grating profiles, tunable, narrow-band MIR and broadband MIR spectra are both observed in this geometry. Finally, we perform numerical modeling using a nonlinear envelope equation, which shows good quantitative agreement with the experiment---and can be used to inform waveguide designs to tailor the MIR frequency combs. Our results identify a path to a simple single-branch approach to mid-infrared frequency comb generation in a compact platform using commercial Er:fiber technology.

physics.optics↗

arXiv2018

Searching for Exoplanets Using a Microresonator Astrocomb

Detection of weak radial velocity shifts of host stars induced by orbiting planets is an important technique for discovering and characterizing planets beyond our solar system. Optical frequency combs enable calibration of stellar radial velocity shifts at levels required for detection of Earth analogs. A new chip-based device, the Kerr soliton microcomb, has properties ideal for ubiquitous application outside the lab and even in future space-borne instruments. Moreover, microcomb spectra are ideally suited for astronomical spectrograph calibration and eliminate filtering steps required by conventional mode-locked-laser frequency combs. Here, for the calibration of astronomical spectrographs, we demonstrate an atomic/molecular line-referenced, near-infrared soliton microcomb. Efforts to search for the known exoplanet HD 187123b were conducted at the Keck-II telescope as a first in-the-field demonstration of microcombs.

physics.optics↗

arXiv2017

Dual frequency comb spectroscopy in the molecular fingerprint region

Spectroscopy in the molecular fingerprint spectral region (6.5-20 $μ$m) yields critical information on material structure for physical, chemical and biological sciences. Despite decades of interest and effort, this portion of the electromagnetic spectrum remains challenging to cover with conventional laser technologies. In this report, we present a simple and robust method for generating super-octave, optical frequency combs in the fingerprint region through intra-pulse difference frequency generation in an orientation-patterned gallium phosphide crystal. We demonstrate the utility of this unique coherent light source for high-precision, dual-comb spectroscopy in methanol and ethanol vapor. These results highlight the potential of laser frequency combs for a wide range of molecular sensing applications, from basic molecular spectroscopy to nanoscopic imaging.

physics.optics↗

arXiv2017

Quasi-phase-matched supercontinuum-generation in photonic waveguides

Supercontinuum generation in integrated photonic waveguides is a versatile source of broadband light, and the generated spectrum is largely determined by the phase-matching conditions. Here we show that quasi-phase-matching via periodic modulations of the waveguide structure provides a useful mechanism to control the evolution of ultrafast pulses and the supercontinuum spectrum. We experimentally demonstrate quasi-phase-matched supercontinuum to the TE20 and TE00 waveguide modes, which enhances the intensity of the SCG in specific spectral regions by as much as 20 dB. We utilize higher-order quasi-phase-matching (up to the 16th order) to enhance the intensity in numerous locations across the spectrum. Quasi-phase-matching adds a unique dimension to the design-space for SCG waveguides, allowing the spectrum to be engineered for specific applications.

physics.optics↗

arXiv2017

An ultrafast electro-optic light source with sub-cycle precision

Controlling femtosecond optical pulses with temporal precision better than one cycle of the carrier field has a profound impact on measuring and manipulating interactions between light and matter. We explore pulses that are carved from a continuous-wave laser via electro-optic modulation and realize the regime of sub-cycle optical control without a mode-locked resonator. Our ultrafast source, with a repetition rate of 10 GHz, is derived from an optical-cavity-stabilized laser and a microwave-cavity-stabilized electronic oscillator. Sub-cycle timing jitter of the pulse train is achieved by coherently linking the laser and oscillator through carrier-envelope phase stabilization enabled by a photonic-chip supercontinuum that spans up to 1.9 octaves across the near infrared. Moreover, the techniques we report are relevant for other ultrafast lasers with repetition rates up to 30 GHz and may allow stable few-cycle pulses to be produced by a wider range of sources.

physics.optics↗

arXiv2017

Kerr-microresonator solitons for accurate carrier-envelope-frequency stabilization

Carrier-envelope phase stabilization of optical pulses enables exquisitely precise measurements by way of direct optical-frequency synthesis, absolute optical-to-microwave phase conversion, and control of ultrafast waveforms. We report such phase stabilization for Kerr-microresonator frequency combs integrated on silicon chips, and verify their fractional-frequency inaccuracy at <3x10-16. Our work introduces an interlocked Kerr-comb configuration comprised of one silicon-nitride and one silica microresonator, which feature nearly harmonic repetition frequencies and can be generated with one laser. These frequency combs support an ultrafast-laser regime with few-optical-cycle, 1-picosecond-period soliton pulses and a total dispersive-wave-enhanced bandwidth of 170 THz, while providing a stable phase-link between the optical and microwave domains. To accommodate low-power and mobile application platforms, our phase-locked frequency-comb system operates with <250 mW of chip-coupled power. Our work establishes Kerr-microresonator combs as a viable technology for applications like optical-atomic timekeeping, optical synthesis, and related directions.

physics.optics↗

arXiv2017

Optical-frequency measurements with a Kerr-microcomb and photonic-chip supercontinuum

Dissipative solitons formed in Kerr microresonators may enable chip-scale frequency combs for precision optical metrology. Here we explore the creation of an octave-spanning, 15-GHz repetition-rate microcomb suitable for both f-2f self-referencing and optical-frequency comparisons across the near infrared. This is achieved through a simple and reliable approach to deterministically generate, and subsequently frequency stabilize, soliton pulse trains in a silica-disk resonator. Efficient silicon-nitride waveguides provide a supercontinuum spanning 700 to 2100 nm, enabling both offset-frequency stabilization and optical-frequency measurements with >100 nW per mode. We demonstrate the stabilized comb by performing a microcomb-mediated comparison of two ultrastable optical-reference cavities.

physics.optics↗

arXiv2017

High-harmonic generation in periodically poled waveguides

Optical waveguides made from periodically poled materials provide high confinement of light and enable the generation of new wavelengths via quasi-phase-matching, making them a key platform for nonlinear optics and photonics. However, such devices are not typically employed for high-harmonic generation. Here, using 200-fs, 10-nJ-level pulses of 4100 nm light at 1 MHz, we generate high harmonics up to the 13th harmonic (315 nm) in a chirped, periodically poled lithium niobate (PPLN) waveguide. Total conversion efficiencies into the visible--ultraviolet region are as high as 10 percent. We find that the output spectrum depends on the waveguide poling period, indicating that quasi-phase-matching plays a significant role. In the future, such periodically poled waveguides may enable compact sources of ultrashort pulses at high repetition rates and provide new methods of probing the electronic structure of solid-state materials.

physics.optics↗

arXiv2017

An Integrated-Photonics Optical-Frequency Synthesizer

Integrated-photonics microchips now enable a range of advanced functionalities for high-coherence applications such as data transmission, highly optimized physical sensors, and harnessing quantum states, but with cost, efficiency, and portability much beyond tabletop experiments. Through high-volume semiconductor processing built around advanced materials there exists an opportunity for integrated devices to impact applications cutting across disciplines of basic science and technology. Here we show how to synthesize the absolute frequency of a lightwave signal, using integrated photonics to implement lasers, system interconnects, and nonlinear frequency comb generation. The laser frequency output of our synthesizer is programmed by a microwave clock across 4 THz near 1550 nm with 1 Hz resolution and traceability to the SI second. This is accomplished with a heterogeneously integrated III/V-Si tunable laser, which is guided by dual dissipative-Kerr-soliton frequency combs fabricated on silicon chips. Through out-of-loop measurements of the phase-coherent, microwave-to-optical link, we verify that the fractional-frequency instability of the integrated photonics synthesizer matches the $7.0*10^{-13}$ reference-clock instability for a 1 second acquisition, and constrain any synthesis error to $7.7*10^{-15}$ while stepping the synthesizer across the telecommunication C band. Any application of an optical frequency source would be enabled by the precision optical synthesis presented here. Building on the ubiquitous capability in the microwave domain, our results demonstrate a first path to synthesis with integrated photonics, leveraging low-cost, low-power, and compact features that will be critical for its widespread use.

physics.app-ph↗

arXiv2017

Ultrabroadband supercontinuum generation and frequency-comb stabilization using on-chip waveguides with both cubic and quadratic nonlinearities

Using aluminum-nitride photonic-chip waveguides, we generate optical-frequency-comb supercontinuum spanning from 500 nm to 4000 nm with a 0.8 nJ seed pulse, and show that the spectrum can be tailored by changing the waveguide geometry. Since aluminum nitride exhibits both quadratic and cubic nonlinearities, the spectra feature simultaneous contributions from numerous nonlinear mechanisms: supercontinuum generation, difference-frequency generation, second-harmonic generation, and third-harmonic generation. As one application of integrating multiple nonlinear processes, we measure and stabilize the carrier-envelope-offset frequency of a laser comb by direct photodetection of the output light. Additionally, we generate ~0.3 mW in the 3000 nm to 4000 nm region, which is potentially useful for molecular spectroscopy. The combination of broadband light generation from the visible through the mid-infrared, combined with simplified self-referencing, provides a path towards robust comb systems for spectroscopy and metrology in the field.

physics.optics↗

arXiv2017

Self-referenced frequency combs using high-efficiency silicon-nitride waveguides

We utilize silicon-nitride waveguides to self-reference a telecom-wavelength fiber frequency comb through supercontinuum generation, using 11.3 mW of optical power incident on the chip. This is approximately ten times lower than conventional approaches using nonlinear fibers and is enabled by low-loss (<2 dB) input coupling and the high nonlinearity of silicon nitride, which can provide two octaves of spectral broadening with incident energies of only 110 pJ. Following supercontinuum generation, self-referencing is accomplished by mixing 780-nm dispersive-wave light with the frequency-doubled output of the fiber laser. In addition, at higher optical powers, we demonstrate f-to-3f self-referencing directly from the waveguide output by the interference of simultaneous supercontinuum and third harmonic generation, without the use of an external doubling crystal or interferometer. These hybrid comb systems combine the performance of fiber-laser frequency combs with the high nonlinearity and compactness of photonic waveguides, and should lead to low-cost, fully stabilized frequency combs for portable and space-borne applications.

physics.optics↗

arXiv2017

Soliton crystals in Kerr resonators

Strongly interacting solitons confined to an optical resonator would offer unique capabilities for experiments in communication, computation, and sensing with light. Here we report on the discovery of soliton crystals in monolithic Kerr microresonators-spontaneously and collectively ordered ensembles of co-propagating solitons whose interactions discretize their allowed temporal separations. We unambiguously identify and characterize soliton crystals through analysis of their 'fingerprint' optical spectra, which arise from spectral interference between the solitons. We identify a rich space of soliton crystals exhibiting crystallographic defects, and time-domain measurements directly confirm our inference of their crystal structure. The crystallization we observe is explained by long-range soliton interactions mediated by resonator mode degeneracies, and we probe the qualitative difference between soliton crystals and a soliton liquid that forms in the absence of these interactions. Our work explores the rich physics of monolithic Kerr resonators in a new regime of dense soliton occupation and offers a way to greatly increase the efficiency of Kerr combs; further, the extreme degeneracy of the configuration space of soliton crystals suggests an implementation for a robust on-chip optical buffer.

physics.optics↗

arXiv2016

Stably accessing octave-spanning microresonator frequency combs in the soliton regime

Microresonator frequency combs can be an enabling technology for optical frequency synthesis and timekeeping in low size, weight, and power architectures. Such systems require comb operation in low-noise, phase-coherent states such as solitons, with broad spectral bandwidths (e.g., octave-spanning) for self-referencing to detect the carrier-envelope offset frequency. However, stably accessing such states is complicated by thermo-optic dispersion. For example, in the Si3N4 platform, precisely dispersion-engineered structures can support broadband operation, but microsecond thermal time constants have necessitated fast pump power or frequency control to stabilize the solitons. In contrast, here we consider how broadband soliton states can be accessed with simple pump laser frequency tuning, at a rate much slower than the thermal dynamics. We demonstrate octave-spanning soliton frequency combs in Si3N4 microresonators, including the generation of a multi-soliton state with a pump power near 40 mW and a single-soliton state with a pump power near 120 mW. We also develop a simplified two-step analysis to explain how these states are accessed in a thermally stable way without fast control of the pump laser, and outline the required thermal properties for such operation. Our model agrees with experimental results as well as numerical simulations based on a Lugiato-Lefever equation that incorporates thermo-optic dispersion. Moreover, it also explains an experimental observation that a member of an adjacent mode family on the red-detuned side of the pump mode can mitigate the thermal requirements for accessing soliton states.

physics.optics↗

arXiv2016

Microresonator Brillouin Laser Stabilization Using a Microfabricated Rubidium Cell

We frequency stabilize the output of a miniature stimulated Brillouin scattering (SBS) laser to rubidium atoms in a microfabricated cell to realize a laser system with frequency stability at the $10^{-11}$ level over seven decades in averaging time. In addition, our system has the advantages of robustness, low cost and the potential for integration that would lead to still further miniaturization. The SBS laser operating at 1560 nm exhibits a spectral linewidth of 820 Hz, but its frequency drifts over a few MHz on the 1 hour timescale. By locking the second harmonic of the SBS laser to the Rb reference, we reduce this drift by a factor of $10^3$ to the level of a few kHz over the course of an hour. For our combined SBS and Rb laser system, we measure a frequency noise of $4\times10^4$ $Hz^2/Hz$ at 10 Hz offset frequency which rapidly rolls off to a level of 0.2 $Hz^2/Hz$ at 100 kHz offset. The corresponding Allan deviation is $\leq2\times10^{-11}$ for averaging times spanning $10^{-4}$ to $10^3$ s. By optically dividing the signal of the laser down to microwave frequencies, we generate an RF signal at 2 GHz with phase noise at the level of -76 dBc/Hz and -140 dBc/Hz at offset frequencies of 10 Hz and 10 kHz, respectively.

physics.optics↗

arXiv2015

Phase Coherent Link of an Atomic Clock to a Self-Referenced Microresonator Frequency Comb

The counting and control of optical cycles of light has become common with modelocked laser frequency combs. But even with advances in laser technology, modelocked laser combs remain bulk-component devices that are hand-assembled. In contrast, a frequency comb based on the Kerr-nonlinearity in a dielectric microresonator will enable frequency comb functionality in a micro-fabricated and chip-integrated package suitable for use in a wide-range of environments. Such an advance will significantly impact fields ranging from spectroscopy and trace gas sensing, to astronomy, communications, atomic time keeping and photonic data processing. Yet in spite of the remarkable progress shown over the past years, microresonator frequency combs ("microcombs") have still been without the key function of direct f-2f self-referencing and phase-coherent frequency control that will be critical for enabling their full potential. Here we realize these missing elements using a low-noise 16.4 GHz silicon chip microcomb that is coherently broadened from its initial 1550 nm wavelength and subsequently f-2f self-referenced and phase-stabilized to an atomic clock. With this advance, we not only realize the highest repetition rate octave-span frequency comb ever achieved, but we highlight the low-noise microcomb properties that support highest atomic clock limited frequency stability.

physics.optics↗

arXiv2015

A microrod-resonator Brillouin laser with 240 Hz absolute linewidth

We demonstrate an ultralow-noise microrod-resonator based laser that oscillates on the gain supplied by the stimulated Brillouin scattering optical nonlinearity. Microresonator Brillouin lasers are known to offer an outstanding frequency noise floor, which is limited by fundamental thermal fluctuations. Here, we show experimental evidence that thermal effects also dominate the close-to-carrier frequency fluctuations. The 6-mm diameter microrod resonator used in our experiments has a large optical mode area of ~100 μm$^2$, and hence its 10 ms thermal time constant filters the close-to-carrier optical frequency noise. The result is an absolute laser linewidth of 240 Hz with a corresponding white-frequency noise floor of 0.1 Hz$^2$/Hz. We explain the steady-state performance of this laser by measurements of its operation state and of its mode detuning and lineshape. Our results highlight a mechanism for noise that is common to many microresonator devices due to the inherent coupling between intracavity power and mode frequency. We demonstrate the ability to reduce this noise through a feedback loop that stabilizes the intracavity power.

physics.optics↗