arXiv subjects

Shota Abe

Publications and source records attributed to Shota Abe.

4 recordsLinked to original sources

arXiv2024

Importance of Gas Heating in Capacitively Coupled Radiofrequency Plasma-assisted Synthesis of Carbon Nanomaterials

In pursuit of diamond nanoparticles, a capacitively-coupled radio frequency (CCRF) flow-through plasma reactor was operated with methane argon gas mixtures. Signatures of the final product obtained microscopically and spectroscopically indicated that the product was an amorphous form of graphite. This result was consistent irrespective of combinations of the macroscopic reactor settings. To explain the observed synthesis output, measurements of C2 and gas properties were carried out by laser-induced fluorescence and optical emission spectroscopy. Strikingly, the results indicated a strong gas temperature gradient of 100 K per mm from the center of the reactor to the wall. Based on additional plasma imaging, a model of hot constricted region (filamentation region) was then formulated. It illustrated that, while the hot constricted region was present, the bulk of the gas was not hot enough to facilitate diamond sp3 formation: characterized by much lower reaction rates, when compared to sp2, sp3 formation kinetics are expected to become exponentially slow. This result was further confirmed by experiments under identical conditions but with a H2/CH4 mixture, where no output material was detected: if graphitic sp2 formation was expected as the main output material from the methane feedstock, atomic hydrogen would then be expected to etch it away in situ, such that the net production of that sp2-hybridized solid material is nearly a zero.

physics.plasm-ph↗

arXiv2023

Kinetic Modeling Analysis of Ar Addition to Atmospheric Pressure N2-H2 Plasma for Plasma-Assisted Catalytic Synthesis of NH3

Zero-dimensional kinetic modeling of atmospheric pressure Ar-N2-H2 nonthermal plasma was carried out to gain mechanistic insights into ammonia formation during plasma-assisted catalysis of ammonia synthesis. The kinetic model was developed for a coaxial dielectric barrier discharge (DBD) quartz wool-packed bed reactor operating at near room temperature using a kHz-frequency plasma source. With 30% Ar mixed in a 1:1 N2-H2 plasma at 760 Torr, we find that NH3 production is dominated by Eley-Rideal (E-R) surface reactions, which heavily involve surface NHx species derived from N and H radicals in the gas phase, while the influence of excited N2 molecules is negligible. This is contrary to the commonly proposed mechanism that excited N2 molecules created by Penning excitation of N2 by Ar (4s) and Ar(4p) plays a significant role in assisting NH3 formation. Our model shows that the enhanced NH3 formation upon Ar dilution is unlikely due to the interactions between Ar and H species, as excited Ar atoms have a weak effect on H radical formation through H2 dissociation compared to electrons. We find that excited Ar atoms contribute to 28% of the N radical production in the gas phase via N2 dissociation, while the rest is dominated by electron-impact dissociation. Furthermore, Ar species play a negligible role in the product NH3 dissociation. N2 conversion sensitivity analyses were carried out for electron density (ne) and reduced electric field (E/N), and contributions from Ar to gas-phase N radical production were quantified. The model can provide guidance on potential reasons for observing enhanced NH3 formation upon Ar dilution in N2-H2 plasmas beyond changes to the discharge characteristics.

physics.plasm-ph↗

arXiv2023

Investigation of W-SiC compositionally graded films as a divertor material

W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. This study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices.

physics.plasm-ph↗

arXiv2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from $3.9-7.5\times10^{19}$ m$^{-3}$ and input powers ranging from $5.5-9$ MW. The small Si pellets were delivered with the impurity granule injector (IGI) at frequencies ranging from 4-16 Hz corresponding to mass flow rates of $5-19$ mg/s ($1-4.2\times10^{20}$ Si/s) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system (DiMES) to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO$_2$ is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least $0.4-1.2$ nm thickness have been deposited at $0.4-0.7$ nm/s. The technique is estimated to coat a surface area of at least 0.94 m$^2$ on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

physics.plasm-ph↗