arXiv subjects

Steven M. Anlage

Publications and source records attributed to Steven M. Anlage.

At least 109 records · Page 6Linked to original sources

arXiv2009

Sensor Based on Extending the Concept of Fidelity to Classical Waves

We propose and demonstrate a remote sensor scheme by applying the quantum mechanical concept of fidelity loss to classical waves. The sensor makes explicit use of time-reversal invariance and spatial reciprocity in a wave chaotic system to sensitively and remotely measure the presence of small perturbations. The loss of fidelity is measured through a classical wave-analog of the Loschmidt echo by employing a single-channel time-reversal mirror to rebroadcast a probe signal into the perturbed system. We also introduce the use of exponential amplification of the probe signal to partially overcome the effects of propagation losses and to vary the sensitivity.

nlin.CD↗

arXiv2009

Phase-sensitive Harmonic Measurements of Microwave Nonlinearities in Cuprate Thin Films

Investigations of the intrinsic electromagnetic nonlinearity of superconductors give insight into the fundamental physics of these materials. Phase-sensitive third-order harmonic voltage data $\tilde{u}_{3f}=|u_{3f}|exp(iϕ_{3f})$ are acquired with a near-field microwave microscope on homogeneous YBa$_2$Cu$_3$O$_{7-δ}$ (YBCO) thin films in a temperature range close to the critical temperature T$_c$. As temperature is increased from below T$_c$, the harmonic magnitude exhibits a maximum, while the phase, $π/2$ in the superconducting state, goes through a minimum. It is found that samples with doping ranges from near optimal ($δ=0.16$) to underdoped ($δ=0.47$) exhibit different behavior in terms of both the harmonic magnitude and phase. In optimally-doped samples, the harmonic magnitude reaches its maximum at a temperature $T_M$ slightly lower than that associated with the minimum of phase $T_m$ and drops into the noisefloor as soon as $T_m$ is exceeded. In underdoped samples $T_M$ is shifted toward lower temperatures with respect to $T_m$ and the harmonic voltage magnitude decreases slower with temperature than in the case of optimally-doped samples. A field-based analytical model of $\tilde{u}_{3f}$ is presented, where the nonlinear behavior is introduced as corrections to the low-field, linear-response complex conductivity. The model reproduces the low-temperature regime where the $σ_2$ nonlinearity dominates, in agreement with published theoretical and experimental results. Additionally the model identifies $T_m$ as the temperature where the order parameter relaxation time becomes comparable to the microwave probing period and reproduces semi-quantitatively the experimental data.

cond-mat.supr-con↗

arXiv2008

Dynamical scaling of $YBa_2Cu_3O_{7-δ}$ thin film conductivity in zero field

We study dynamic fluctuation effects of $YBa_2Cu_3O_{7-δ}$ thin films in zero field around $T_c$ by doing frequency-dependent microwave conductivity measurements at different powers. The length scales probed in the experiments are varied systematically allowing us to analyze data which are not affected by the finite thickness of the films, and to observe single-parameter scaling. DC current-voltage characteristics have also been measured to independently probe fluctuations in the same samples. The combination of DC and microwave measurements allows us to precisely determine critical parameters. Our results give a dynamical scaling exponent $z=1.55\pm0.15$, which is consistent with model E-dynamics.

cond-mat.supr-con↗

arXiv2008

Frequency- and electric-field-dependent conductivity of single-walled carbon nanotube networks of varying density

We present measurements of the frequency and electric field dependent conductivity of single walled carbon nanotube(SWCNT) networks of various densities. The ac conductivity as a function of frequency is consistent with the extended pair approximation model and increases with frequency above an onset frequency $ω_0$ which varies over seven decades with a range of film thickness from sub-monolayer to 200 nm. The nonlinear electric field-dependent DC conductivity shows strong dependence on film thickness as well. Measurement of the electric field dependence of the resistance R(E) allows for the determination of a length scale $L_{E}$ possibly characterizing the distance between tube contacts, which is found to systematically decrease with increasing film thickness. The onset frequency $ω_0$ of ac conductivity and the length scale $L_{E}$ of SWCNT networks are found to be correlated, and a physically reasonable empirical formula relating them has been proposed. Such studies will help the understanding of transport properties and benefit the applications of this material system.

cond-mat.mtrl-sci↗

arXiv2007

Spatial correlation of linear and nonlinear electron transport in superconducting microwave resonator: laser scanning microscopy analysis

Spatially-resolved techniques of laser scanning microscopy (LSM) have been used to image simultaneously the spatial variations of (i) rf current flow, J$_RF$(x,y), of (ii) areas of resistive dissipation and (iii) the sources of microwave nonlinearity (NL) in an operating superconducting resonator. The RF power dependent spatial evolution of these linear and NL microwave properties in the meander strip YBCO/LAO superconducting resonator have been LSM probed at different temperatures below Tc. The influence of both topologies of the twin-domain YBCO structure and of J$_RF$(x,y) peaks at the edges of superconducting strip line on its NL properties was analyzed in detail with a micron-scale spatial resolution. Result shows the resistive origin of the dominant sources of microwave NLs

cond-mat.supr-con↗

arXiv2007

Microwave shielding of transparent and conducting single-walled carbon nanotube films

The authors measured the transport properties of single-walled carbon nanotube (SWCNT) films in the microwave frequency range from 10 MHz to 30 GHz by using the Corbino reflection technique from temperatures of 20-400 K. Based on the real and imaginary parts of the microwave conductivity, they calculated the shielding effectiveness for various film thicknesses. Shielding effectiveness of 43 dB at 10 MHz and 28 dB at 10 GHz are found for films with 90% optical transmittance, which suggests that SWCNT films are promising as a type of transparent microwave shielding material. By combining their data with those from the literature, the conductivity of SWCNT films was established in a broad frequency range from dc to visible.

cond-mat.mtrl-sci↗

arXiv2007

Nanometer-Scale Materials Contrast Imaging with a Near-Field Microwave Microscope

We report topography-free materials contrast imaging on a nano-fabricated Boron-doped Silicon sample measured with a Near-field Scanning Microwave Microscope over a broad frequency range. The Boron doping was performed using the Focus Ion Beam technique on a Silicon wafer with nominal resistivity of 61 Ohm.cm. A topography-free doped region varies in sheet resistance from 1000Ohm/Square to about 400kOhm/Square within a lateral distance of 4 micrometer. The qualitative spatial-resolution in sheet resistance imaging contrast is no worse than 100 nm as estimated from the frequency shift signal.

cond-mat.mtrl-sci↗

arXiv2007

Broadband dielectric microwave microscopy on $μ$m length scales

We demonstrate that a near-field microwave microscope based on a transmission line resonator allows imaging in a substantially wide range of frequencies, so that the microscope properties approach those of a spatially-resolved impedance analyzer. In the case of an electric probe, the broadband imaging can be used in a direct fashion to separate contributions from capacitive and resistive properties of a sample at length scales on the order of one micron. Using a microwave near-field microscope based on a transmission line resonator we imaged the local dielectric properties of a Focused Ion Beam (FIB) milled structure on a high-dielectric-constant Ba_{0.6}Sr_{0.4}TiO_3 (BSTO) thin film in the frequency range from 1.3 GHz to 17.4 GHz. The electrostatic approximation breaks down already at frequencies above ~10 GHz for the probe geometry used, and a full-wave analysis is necessary to obtain qualitative information from the images.

cond-mat.mtrl-sci↗

arXiv2006

Tunability of Superconducting Metamaterials

Metamaterials are artificial structures with unique electromagnetic properties, such as relative dielectric permittivity and magnetic permeability with values less than 1, or even negative. Because these properties are so sensitive to loss, we have developed metamaterials comprised of superconducting waveguides, wires, and split-ring resonators. An important requirement for applications of these metamaterials is the ability to tune the frequency at which the unique electromagnetic response occurs. In this paper we present three methods (unique to superconductors) to accomplish this tuning: temperature, dc magnetic field, and rf magnetic field. Data are shown for dc and rf magnetic field tuning of a single Nb split-ring resonator (SRR). It was found that the dc field tuning was hysteritic in the resonant frequency data, while the quality factor, $Q$, was less hystertic. The rf power tuning showed no hysteresis, but did show supression of the $Q$ at high power. Magneto-optical images reveal inhomogeneous magnetic vortex entry in the dc field tuning, and laser scanning photoresponse images for a YBa$_2$Cu$_3$O$_{7-δ}$ SRR reveals the current distribution in the rings.

cond-mat.supr-con↗

arXiv2006

Local Dielectric Measurements of BaTiO3-CoFe2O4 Nano-composites Through Microwave Microscopy

We report on linear and non-linear dielectric property measurements of BaTiO3 - CoFe2O4 (BTO-CFO) ferroelectro-magnetic nano-composites and pure BaTiO3 and CoFe2O4 samples with Scanning Near Field Microwave Microscopy. The permittivity scanning image with spatial resolution on the micro-meter scale shows that the nano-composites have very uniform quality with an effective dielectric constant ε_r = 140 +/- 6.4 at 3.8 GHz and room temperature. The temperature dependence of dielectric permittivity shows that the Curie temperature of pure BTO was shifted by the clamping effect of the MgO substrate, whereas the Curie temperature shift of the BTO ferroelectric phase in BTO-CFO composites is less pronounced, and if it exists at all, would be mainly caused by the CFO. Non-linear dielectric measurements of BTO-CFO show good ferroelectric properties from BTO.

cond-mat.mtrl-sci↗

arXiv2006

Experimental Test of Universal Conductance Fluctuations by means of Wave-Chaotic Microwave Cavities

The mathematical equivalence of the time-independent Schrodinger equation and the Helmholtz equation is exploited to provide a novel means of studying universal conductance fluctuations in ballistic chaotic mesoscopic systems using a two-dimensional microwave-cavity. The classically chaotic ray trajectories within a suitably-shaped microwave cavity play a role analogous to that of the chaotic dynamics of non-interacting electron transport through a ballistic quantum dot in the absence of thermal fluctuations. The microwave cavity is coupled through two single-mode ports and the effect of non-ideal coupling between the ports and cavity is removed by a previously developed method based on the measured radiation impedance matrix. The Landauer-Buttiker formalism is applied to obtain the conductance of a corresponding mesoscopic quantum-dot device. We find good agreement for the probability density functions (PDFs) of the experimentally derived surrogate conductance, as well as its mean and variance, with the theoretical predictions of Brouwer and Beenakker. We also observe a linear relation between the quantum dephasing parameter and the cavity ohmic loss parameter.

cond-mat.mes-hall↗

arXiv2006

Imaging of Microscopic Sources of Resistive and Reactive Nonlinearities in Superconducting Microwave Devices

The technique of low-temperature Laser Scanning Microscopy (LSM) has been applied to the investigation of local microwave properties in operating YBa2Cu3O7/LaAlO3 thin-film resonators patterned into a meandering strip transmission line. By using a modified newly developed procedure of spatially-resolved complex impedance partition, the influence of inhomogeneous current flow on the formation of nonlinear (NL) microwave response in such planar devices is analyzed in terms of the independent impact from resistive and inductive components. The modified procedure developed here is dramatically faster than our previous method. The LSM capability to probe the spatial variations of two-tone, third-order intermodulation currents on micron length scales is used to find the 2D distribution of the local sources of microwave NL. The results show that the dominant sources of microwave NL are strongly localized in the resistive domains.

cond-mat.supr-con↗

arXiv2006

Universal Properties of 2-Port Scattering, Impedance and Admittance Matrices of Wave Chaotic Systems

Statistical fluctuations in the eigenvalues of the scattering, impedance and admittance matrices of 2-Port wave-chaotic systems are studied experimentally using a chaotic microwave cavity. These fluctuations are universal in that their properties are dependent only upon the degree of loss in the cavity. We remove the direct processes introduced by the non-ideally coupled driving ports through a matrix-normalization process that involves the radiation-impedance matrix of the two driving ports. We find good agreement between the experimentally obtained marginal probability density functions (PDFs) of the eigenvalues of the normalized impedance, admittance and scattering matrix and those from Random Matrix Theory (RMT). We also experimentally study the evolution of the joint PDF of the eigenphases of the normalized scattering matrix as a function of loss. Experimental agreement with the theory by Brouwer and Beenakker for the joint PDF of the magnitude of the eigenvalues of the normalized scattering matrix is also shown.

cond-mat.dis-nn↗

arXiv2006

Delayed Feedback and Chaos on the Driven Diode-Terminated Transmission Line

A simple model of a distributed, non-linear circuit that produces chaos at GHz frequencies is introduced and tested experimentally. The model circuit is a driven diode-terminated transmission line with the transmission line impedance mismatched to that of the source. Experiments were performed with sinusoidal driving frequencies of 10 MHz to 1.2 GHz, driving powers of -30 to +50 dBm and transmission line delay times from 3 to 20 ns. Diode reverse recovery times ranged from 4 to 100 ns. As a result of many experiments, it was found that chaotic behavior was strongly dependent on the unbiased, small-signal reactance of the system as seen by the driving source, and influenced by an applied DC voltage-bias across the diode. In the experiments that showed period-doubling and / or chaos, the reverse recovery times of the diodes were on the order of both the driving period and the delay time of the circuits. Comparisons between theory and experiment are in general agreement. Chaos produced with a driving frequency of 1.105 GHz has been observed experimentally.

nlin.CD↗

arXiv2006

Single Superconducting Split-Ring Resonator Electrodynamics

We investigate the microwave electrodynamic properties of a single superconducting thin film split-ring resonator (SRR). The experiments were performed in an all-Nb waveguide, with Nb wires and Nb SRRs. Transmission data showed a high-Q stopband for a single Nb SRR ($Q \sim 4.5\times10^4$ at 4.2 K) below $T_c$, and no such feature for a Cu SRR, or closed Nb loops, of similar dimensions. Adding SRRs increased the bandwidth, but decreased the insertion loss of the features. Placing the Nb SRR into an array of wires produced a single, elementary negative-index passband ($Q \sim 2.26\times10^4$ at 4.2 K). Changes in the features due to the superconducting kinetic inductance were observed. Models for the SRR permeability, and the wire dielectric response, were used to fit the data.

cond-mat.other↗

arXiv2006

Characterization of Fluctuations of Impedance and Scattering Matrices in Wave Chaotic Scattering

In wave chaotic scattering, statistical fluctuations of the scattering matrix $S$ and the impedance matrix $Z$ depend both on universal properties and on nonuniversal details of how the scatterer is coupled to external channels. This paper considers the impedance and scattering variance ratios, $VR_z$ and $VR_s$, where $VR_z=Var[Z_{ij}]/\{Var[Z_{ii}]Var[Z_{jj}] \}^{1/2}$, $VR_s=Var[S_{ij}]/\{Var[S_{ii}]Var[S_{jj}] \}^{1/2}$, and $Var[.]$ denotes variance. $VR_z$ is shown to be a universal function of distributed losses within the scatterer. That is, $VR_z$ is independent of nonuniversal coupling details. This contrasts with $VR_s$ for which universality applies only in the large loss limit. Explicit results are given for $VR_z$ for time reversal symmetric and broken time reversal symmetric systems. Experimental tests of the theory are presented using data taken from scattering measurements on a chaotic microwave cavity.

cond-mat.mes-hall↗

arXiv2005

Measurement of Local Reactive and Resistive Photoresponse of a Superconducting Microwave Device

We propose and demonstrate a spatial partition method for the high-frequency photo-response of superconducting devices correlated with inductive and resistive changes in microwave impedance. Using a laser scanning microscope, we show that resistive losses are mainly produced by local defects at microstrip edges and by intergrain weak links in the high-temperature superconducting material. These defects initiate nonlinear high-frequency response due to overcritical current densities and entry of vortices.

cond-mat.supr-con↗

arXiv2005

Laser Scanning Microscopy of HTS Films and Devices

The work describes the capabilities of Laser Scanning Microscopy (LSM) as a spatially resolved method of testing high_Tc materials and devices. The earlier results obtained by the authors are briefly reviewed. Some novel applications of the LSM are illustrated, including imaging the HTS responses in rf mode, probing the superconducting properties of HTS single crystals, development of twobeam laser scanning microscopy. The existence of the phase slip lines mechanism of resistivity in HTS materials is proven by LSM imaging.

cond-mat.supr-con↗