arXiv subjects

Tie Jun Cui

Publications and source records attributed to Tie Jun Cui.

At least 55 records · Page 3Linked to original sources

arXiv2024

Reconfigurable Intelligent Surface: Power Consumption Modeling and Practical Measurement Validation

The reconfigurable intelligent surface (RIS) has received a lot of interest because of its capacity to reconfigure the wireless communication environment in a cost- and energy-efficient way. However, the realistic power consumption modeling and measurement validation of RIS has received far too little attention. Therefore, in this work, we model the power consumption of RIS and conduct measurement validations using various RISs to fill this vacancy. Firstly, we propose a practical power consumption model of RIS. The RIS hardware is divided into three basic parts: the FPGA control board, the drive circuits, and the RIS unit cells. The power consumption of the first two parts is modeled as $P_{\text {static}}$ and that of the last part is modeled as $P_{\text {units}}$. Expressions of $P_{\text {static}}$ and $P_{\text {units}}$ vary amongst different types of RISs. Secondly, we conduct measurements on various RISs to validate the proposed model. Five different RISs including the PIN diode, varactor diode, and RF switch types are measured, and measurement results validate the generality and applicability of the proposed power consumption model of RIS. Finally, we summarize the measurement results and discuss the approaches to achieve the low-power-consumption design of RIS-assisted wireless communication systems.

cs.IT↗

arXiv2024

Electromagnetic Information Theory: Fundamentals and Applications for 6G Wireless Communication Systems

In wireless communications, electromagnetic theory and information theory constitute a pair of fundamental theories, bridged by antenna theory and wireless propagation channel modeling theory. Up to the fifth generation (5G) wireless communication networks, these four theories have been developing relatively independently. However, in sixth generation (6G) space-air-ground-sea wireless communication networks, seamless coverage is expected in the three-dimensional (3D) space, potentially necessitating the acquisition of channel state information (CSI) and channel capacity calculation at anywhere and any time. Additionally, the key 6G technologies such as ultra-massive multiple-input multiple-output (MIMO) and holographic MIMO achieves intricate interaction of the antennas and wireless propagation environments, which necessitates the joint modeling of antennas and wireless propagation channels. To address the challenges in 6G, the integration of the above four theories becomes inevitable, leading to the concept of the so-called electromagnetic information theory (EIT). In this article, a suite of 6G key technologies is highlighted. Then, the concepts and relationships of the four theories are unveiled. Finally, the necessity and benefits of integrating them into the EIT are revealed.

cs.IT↗

arXiv2024

Multiperson Detection and Vital-Sign Sensing Empowered by Space-Time-Coding RISs

Passive human sensing using wireless signals has attracted increasing attention due to its superiorities of non-contact and robustness in various lighting conditions. However, when multiple human individuals are present, their reflected signals could be intertwined in the time, frequency and spatial domains, making it challenging to separate them. To address this issue, this paper proposes a novel system for multiperson detection and monitoring of vital signs (i.e., respiration and heartbeat) with the assistance of space-time-coding (STC) reconfigurable intelligent metasurfaces (RISs). Specifically, the proposed system scans the area of interest (AoI) for human detection by using the harmonic beams generated by the STC RIS. Simultaneously, frequencyorthogonal beams are assigned to each detected person for accurate estimation of their respiration rate (RR) and heartbeat rate (HR). Furthermore, to efficiently extract the respiration signal and the much weaker heartbeat signal, we propose an improved variational mode decomposition (VMD) algorithm to accurately decompose the complex reflected signals into a smaller number of intrinsic mode functions (IMFs). We build a prototype to validate the proposed multiperson detection and vital-sign monitoring system. Experimental results demonstrate that the proposed system can simultaneously monitor the vital signs of up to four persons. The errors of RR and HR estimation using the improved VMD algorithm are below 1 RPM (respiration per minute) and 5 BPM (beats per minute), respectively. Further analysis reveals that the flexible beam controlling mechanism empowered by the STC RIS can reduce the noise reflected from other irrelative objects on the physical layer, and improve the signal-to-noise ratio of echoes from the human chest.

eess.SP↗

arXiv2023

Passive Human Sensing Enhanced by Reconfigurable Intelligent Surface: Opportunities and Challenges

Reconfigurable intelligent surfaces (RISs) have flexible and exceptional performance in manipulating electromagnetic waves and customizing wireless channels. These capabilities enable them to provide a plethora of valuable activity-related information for promoting wireless human sensing. In this article, we present a comprehensive review of passive human sensing using radio frequency signals with the assistance of RISs. Specifically, we first introduce fundamental principles and physical platform of RISs. Subsequently, based on the specific applications, we categorize the state-of-the-art human sensing techniques into three types, including human imaging,localization, and activity recognition. Meanwhile, we would also investigate the benefits that RISs bring to these applications. Furthermore, we explore the application of RISs in human micro-motion sensing, and propose a vital signs monitoring system enhanced by RISs. Experimental results are presented to demonstrate the promising potential of RISs in sensing vital signs for manipulating individuals. Finally, we discuss the technical challenges and opportunities in this field.

eess.SP↗

arXiv2023

Multi-Scenario Broadband Channel Measurement and Modeling for Sub-6 GHz RIS-Assisted Wireless Communication Systems

Reconfigurable intelligent surface (RIS)-empowered communication, has been considered widely as one of the revolutionary technologies for next generation networks. However, due to the novel propagation characteristics of RISs, underlying RIS channel modeling and measurement research is still in its infancy and not fully investigated. In this paper, we conduct multi-scenario broadband channel measurements and modeling for RIS-assisted communications at the sub-6 GHz band. The measurements are carried out in three scenarios covering outdoor, indoor, and outdoor-to-indoor (O2I) environments, which suffer from non-line-of-sight (NLOS) propagation inherently. Three propagation modes including intelligent reflection with RIS, specular reflection with RIS and the mode without RIS, are taken into account in each scenario. In addition, considering the cascaded characteristics of RIS-assisted channel by nature, two modified empirical models including floating-intercept (FI) and close-in (CI) are proposed, which cover distance and angle domains. The measurement results rooted in 2096 channel acquisitions verify the prediction accuracy of these proposed models. Moreover, the propagation characteristics for RIS-assisted channels, including path loss (PL) gain, PL exponent, spatial consistency, time dispersion, frequency stationarity, etc., are compared and analyzed comprehensively. These channel measurement and modeling results may lay the groundwork for future applications of RIS-assisted communication systems in practice.

cs.IT↗

arXiv2023

Sensing RISs: Enabling Dimension-Independent CSI Acquisition for Beamforming

Reconfigurable intelligent surfaces (RISs) are envisioned as a potentially transformative technology for future wireless communications. However, RISs' inability to process signals and the attendant increased channel dimension have brought new challenges to RIS-assisted systems, including significantly increased pilot overhead required for channel estimation. To address these problems, several prior contributions that enhance the hardware architecture of RISs or develop algorithms to exploit the channels' mathematical properties have been made, where the required pilot overhead is reduced to be proportional to the number of RIS elements. In this paper, we propose a dimension-independent channel state information (CSI) acquisition approach in which the required pilot overhead is independent of the number of RIS elements. Specifically, in contrast to traditional signal transmission methods, where signals from the base station (BS) and the users are transmitted in different time slots, we propose a novel method in which signals are transmitted from the BS and the user simultaneously during CSI acquisition. With this method, an electromagnetic interference random field (IRF) will be induced on the RIS, and we propose the structure of sensing RIS to capture its features. Moreover, we develop three algorithms for parameter estimation in this system, in which one of the proposed vM-EM algorithm is analyzed with the fixed-point perturbation method to obtain an asymptotic achievable bound. In addition, we also derive the Cramér-Rao lower bound (CRLB) and an asymptotic expression for characterizing the best possible performance of the proposed algorithms. Simulation results verify that our proposed signal transmission method and the corresponding algorithms can achieve dimension-independent CSI acquisition for beamforming.

eess.SP↗

arXiv2023

RIS-Assisted Joint Uplink Communication and Imaging: Phase Optimization and Bayesian Echo Decoupling

Achieving integrated sensing and communication (ISAC) via uplink transmission is challenging due to the unknown waveform and the coupling of communication and sensing echoes. In this paper, a joint uplink communication and imaging system is proposed for the first time, where a reconfigurable intelligent surface (RIS) is used to manipulate the electromagnetic signals for echo decoupling at the base station (BS). Aiming to enhance the transmission gain in desired directions and generate required radiation pattern in the region of interest (RoI), a phase optimization problem for RIS is formulated, which is high dimensional and nonconvex with discrete constraints. To tackle this problem, a back propagation based phase design scheme for both continuous and discrete phase models is developed. Moreover, the echo decoupling problem is tackled using the Bayesian method with the factor graph technique, where the problem is represented by a graph model which consists of difficult local functions. Based on the graph model, a message-passing algorithm is derived, which can efficiently cooperate with the adaptive sparse Bayesian learning (SBL) to achieve joint communication and imaging. Numerical results show that the proposed method approaches the relevant lower bound asymptotically, and the communication performance can be enhanced with the utilization of imaging echoes.

eess.SP↗

arXiv2022

Topological metasurface: From passive toward active and beyond

Metasurfaces are subwavelength structured thin films consisting of arrays of units that allow the controls of polarization, phase and amplitude of light over a subwavelength thickness. The recent developments in topological photonics have greatly broadened the horizon in designing the metasurfaces for novel functional applications. In this review, we summarize recent progress in the research field of topological metasurfaces, firstly from the perspectives of passive and active in the classical regime, and then in the quantum regime. More specifically, we begin by examining the passive topological phenomena in two-dimensional photonic systems, including both time-reversal broken systems and time-reversal preserved systems. Subsequently, we move to discuss the cutting-edge studies of the active topological metasurfaces, including nonlinear topological metasurfaces and reconfigurable topological metasurfaces. After overviewing the topological metasurfaces in the classical regime, we show how the topological metasurfaces could provide a new platform for quantum information and quantum many-body physics. Finally, we conclude and describe some challenges and future directions of this fast-evolving field.

physics.optics↗

arXiv2022

Joint Detections of Frequency and Direction of Arrival in Wideband Based on Programmable Metasurface

We propose to achieve joint detections of frequency and direction of arrival in wideband using single sensor based on an active metasurface with programmable transmission states of pass and stop. By integrating two PIN diodes with the opposite directions into the proposed single-layer and ultrathin meta-atom, the transmission performance with 10 dB difference between the pass and stop states is realized in the bandwidth from 5.9 GHz to 8.8 GHz using field-circuit co-simulations. Accordingly, random receiving patterns are generated by controlling the programmable metasurface composed of the switchable meta-atoms. Afterwards, the frequency and direction information of sources located in the far field are detected using the modified algorithm of estimating signal parameters via rotational invariance techniques (ESPRIT) and the compressive sensing method, respectively. A sample of the programmable metasurface is fabricated and the voltage control system is built up correspondingly. To entirely verify the validity of the proposed method, we conduct three kinds of experiments with one single source, double sources with different frequencies, and double sources with the same frequency, respectively. In all cases, the source information of frequency and direction has been detected preciously in measurements in the frequency band from 6.2 GHz to 8.8 GHz.

physics.app-ph↗

arXiv2022

High-Resolution Programmable Scattering for Wireless Coverage Enhancement: An Indoor Field Trial Campaign

This paper presents a multi-bit reconfigurable intelligent surface (RIS) with a high phase resolution, capable of beam-steering in the azimuthal plane at sub-6 Gigahertz (GHz). Field trials in realistic indoor deployments have been carried out, with coverage enhancement performance ascertained for three common wireless communication scenarios. Namely, serving users in an open lobby with mixed line of sight and non-line of sight conditions, communication via a junction between long corridors, and a multi-floor scenario with propagation via windows. This work explores the potential for reconfigurable intelligent surface (RIS) deployment to mitigate non-line of sight effects in indoor wireless communications. In a single transmitter, single receiver non-line of sight link, received power improvement of as much as 40 dB is shown to be achievable by suitable placement of a RIS, with an instantaneous bandwidth of at least 100 MHz possible over a 3 to 4.5 GHz range. In addition, the effects of phase resolution on the optimal power reception for the multi-bit RIS have been experimentally verified, with a 2.65 dB improvement compared to a 1-bit case.

eess.SP↗

arXiv2022

Reconfigurable intelligent surfaces: Channel characterization and modeling

Reconfigurable intelligent surfaces (RISs) are two dimensional (2D) metasurfaces which can intelligently manipulate electromagnetic waves by low-cost near passive reflecting elements. RIS is viewed as a potential key technology for the sixth generation (6G) wireless communication systems mainly due to its advantages in tuning wireless signals, thus smartly controlling propagation environments. In this paper, we aim at addressing channel characterization and modeling issues of RIS-assisted wireless communication systems. At first, the concept, principle, and potential applications of RIS are given. An overview of RIS based channel measurements and experiments is presented by classifying frequency bands, scenarios, system configurations, RIS constructions, experiment purposes, and channel observations. Then, RIS based channel characteristics are studied, including reflection and transmission, Doppler effect and multipath fading mitigation, channel reciprocity, channel hardening, rank improvement, far field and near field, etc. RIS based channel modeling works are investigated, including largescale path loss models and small-scale multipath fading models. At last, future research directions related to RIS-assisted channels are also discussed.

eess.SP↗

arXiv2022

Directly wireless communication of human minds via non-invasive brain-computer-metasurface platform

Brain-computer interfaces (BCIs), invasive or non-invasive, have projected unparalleled vision and promise for assisting patients in need to better their interaction with the surroundings. Inspired by the BCI-based rehabilitation technologies for nerve-system impairments and amputation, we propose an electromagnetic brain-computer-metasurface (EBCM) paradigm, regulated by human's cognition by brain signals directly and non-invasively. We experimentally show that our EBCM platform can translate human's mind from evoked potentials of P300-based electroencephalography to digital coding information in the electromagnetic domain non-invasively, which can be further processed and transported by an information metasurface in automated and wireless fashions. Directly wireless communications of the human minds are performed between two EBCM operators with accurate text transmissions. Moreover, several other proof-of-concept mind-control schemes are presented using the same EBCM platform, exhibiting flexibly-customized capabilities of information processing and synthesis like visual-beam scanning, wave modulations, and pattern encoding.

cs.IT↗

arXiv2022

Gain and loss induced topological insulating phase in a non Hermitian electrical circuit

There have been considerable efforts devoted to the study of topological phases in certain non-Hermitian systems that possess real eigenfrequencies in the presence of gain and loss. However, it is challenging to experimentally realize such non-Hermitian topological insulators in either quantum or photonic systems, due to the difficulties in introducing controlled gain and loss. On the other hand, the wide choices of active circuit components provide us with unprecedented convenience and flexibility in engineering non-Hermitian topological insulators in electrical circuits. Here, we report experimental realization of a one-dimensional (1D) non-Hermitian topological circuit which exhibits topologically protected edge state purely induced by gain and loss. We show that by tuning the value of the positive/negative resistors in the circuit, our system can switch between different topological phase regions. The topological edge states and interface states are observed at the circuit edge and at the interface between a trivial and nontrivial circuit, which are manifested by a prominent impedance peak at the mid-gap frequency topologically robust to variations of circuit parameters. Our work opens a new gateway towards actively controllable topological systems.

cond-mat.mes-hall↗

arXiv2022

Intelligent resonance tracking of a microwave plasmonic resonator for compact wireless sensors

Plasmonic sensing has been in the spotlight for decades, the concept and applications of which have been generalized to spoof surface plasmons (SSPs) in the microwave band. Here, we report a compact and wireless sensor within a printed circuit board size of 18 mm * 12 mm, tracking the resonance frequency shift of a microwave plasmonic resonator via a software-defined scheme. The microwave plasmonic resonator yields a deep-subwavelength size, enhanced sensitivity, and a good electromagnetic compatibility performance. The software-defined resonance tracking scheme minimalizes the hardware circuit and the consumed spectrum resources, and makes the detection intelligently adaptive to the target resonance, with a signal-to-noise ratio of 69 dB and a data rate of 2272 measuring points per second. The sensor has been validated via acetone vapor concentration sensing, while its applications can be widely extended by replacing the transducer materials. This approach provides compact, sensitive, accurate and intelligent solutions for resonant sensors in the Internet of things (IoT).

eess.SP↗

arXiv2022

Experimental identification of the second-order non-Hermitian skin effect with physics-graph-informed machine learning

Topological phases of matter are conventionally characterized by the bulk-boundary correspondence in Hermitian systems: The topological invariant of the bulk in $d$ dimensions corresponds to the number of $(d-1)$-dimensional boundary states. By extension, higher-order topological insulators reveal a bulk-edge-corner correspondence, such that $n$-th order topological phases feature $(d-n)$-dimensional boundary states. The advent of non-Hermitian topological systems sheds new light on the emergence of the non-Hermitian skin effect (NHSE) with an extensive number of boundary modes under open boundary conditions. Still, the higher-order NHSE remains largely unexplored, particularly in the experiment. We introduce an unsupervised approach -- physics-graph-informed machine learning (PGIML) -- to enhance the data mining ability of machine learning with limited domain knowledge. Through PGIML, we experimentally demonstrate the second-order NHSE in a two-dimensional non-Hermitian topolectrical circuit. The admittance spectra of the circuit exhibit an extensive number of corner skin modes and extreme sensitivity of the spectral flow to the boundary conditions. The violation of the conventional bulk-boundary correspondence in the second-order NHSE implies that modification of the topological band theory is inevitable in higher dimensional non-Hermitian systems.

cond-mat.mes-hall↗

arXiv2021

Path Loss Modeling and Measurements for Reconfigurable Intelligent Surfaces in the Millimeter-Wave Frequency Band

Reconfigurable intelligent surfaces (RISs) provide an interface between the electromagnetic world of wireless propagation environments and the digital world of information science. Simple yet sufficiently accurate path loss models for RISs are an important basis for theoretical analysis and optimization of RIS-assisted wireless communication systems. In this paper, we refine our previously proposed free-space path loss model for RISs to make it simpler, more applicable, and easier to use. The impact of the antenna's directivity of the transmitter, receiver, and the unit cells of the RIS on the path loss is explicitly formulated as an angle-dependent loss factor. The refined model gives more accurate estimates of the path loss of RISs comprised of unit cells with a deep sub-wavelength size. Based on the proposed model, the properties of a single unit cell are evaluated in terms of scattering performance, power consumption, and area, which allows us to unveil fundamental considerations for deploying RISs in high frequency bands. Two fabricated RISs operating in the millimeter-wave (mmWave) band are utilized to carry out a measurement campaign. The measurement results are shown to be in good agreement with the proposed path loss model. In addition, the experimental results suggest an effective form to characterize the power radiation pattern of the unit cell for path loss modeling.

eess.SP↗

arXiv2021

Smart Radio Environments

This Roadmap takes the reader on a journey through the research in electromagnetic wave propagation control via reconfigurable intelligent surfaces. Meta-surface modelling and design methods are reviewed along with physical realisation techniques. Several wireless applications are discussed, including beam-forming, focusing, imaging, localisation, and sensing, some rooted in novel architectures for future mobile communications networks towards 6G.

physics.class-ph↗

arXiv2021

Modeling and Measurements for Multi-path Mitigation with Reconfigurable Intelligent Surfaces

A reconfigurable intelligent surface (RIS) is capable of manipulating electromagnetic waves with its flexibly configurable unit cells, thus is an appealing technology to resist fast fading caused by multi-path in wireless communications. In this paper, a two-path propagation model for RIS-assisted wireless communications is proposed by considering both the direct path from the transmitter to the receiver and the assisted path provided by the RIS. The proposed propagation model unveils that the phase shifts of RISs can be optimized by appropriate configuration for multi-path fading mitigation. In particular, four types of RISs with different configuration capabilities are introduced and their performances on improving received signal power in virtue of the assisted path to resist fast fading are compared through extensive simulation results. In addition, an RIS operating at 35 GHz is used for experimental measurement. The experimental results verify that an RIS has the ability to combat fast fading and thus improves the receiving performance, which may lay a foundation for further researches.

cs.IT↗