arXiv subjects

Tiejun Zhou

Publications and source records attributed to Tiejun Zhou.

16 recordsLinked to original sources

arXiv2026

Antiferromagnetic Ordering Enhanced Magnetic Damping in Mn2Au/CoFeB Bilayers

Antiferromagnets (AFMs) hold significant potential for spintronic devices owing to their insensitivity to external magnetic fields and the absence of stray fields. Beyond these inherent advantages, an AFM can manipulate the magnetic dynamics of a ferromagnet (FM) layer in AFM/FM bilayers, whereas the mechanism of such manipulation remains controversial. Here, we investigate the magnetic dynamics of AFM/FM Mn2Au/CoFeB bilayers via Ferromagnetic Resonance (FMR). It is found that the N\'eel temperature of 2-nm-thick Mn2Au is as low as ~40 K, in sharp contrast to that of bulk Mn2Au, which exceeds 1000 K. In the Mn2Au(2 nm)/CoFeB(4 nm) bilayer, the magnetic damping ${\alpha}$ of the CoFeB layer increases from 0.013 to 0.047 as temperature decreases from 160 K to 10 K, accompanied by a synchronous increase in the exchange coupling field H_rot. Such an increase in ${\alpha}$ is attributed to the enhanced spin angular momentum transfer from CoFeB to Mn2Au, mediated through AFM-FM exchange coupling between Mn2Au and CoFeB, which is enhanced by the Mn2Au antiferromagnetic ordering as the temperature decreases. Our study provides deeper insights into AFM/FM dynamics and spintronic storage technology.

cond-mat.mtrl-sci↗

arXiv2026

Defect annihilation mechanism in the formation of dodecagonal quasicrystals

Understanding defect evolution is essential to the structural stability of quasicrystals, yet the kinetics of defect repair remain poorly understood. Here, by combining the string method and the spring pair method, we determine the minimum energy path from defective to defect-free dodecagonal quasicrystals using a particle model with the Lennard-Jones-Gauss potential. We find that defect annihilation proceeds via three stages: phason flip, aggregation and decomposition of shield-like defects. These sequential transformations are driven by potential energy gradients and accompanied by an increase in structural symmetry. The three stages act synergistically in promoting defect annihilation, offering new insights into the microscopic repair mechanisms of quasicrystals.

cond-mat.mtrl-sci↗

arXiv2025

Nullspace-preserving high-index saddle dynamics method for degenerate multiple solution problems

We propose the nullspace-preserving high-index saddle dynamics (NPHiSD) method for degenerating multiple solution systems in constrained and unconstrained settings. The NPHiSD efficiently locates high-index saddle points and provides parent states for downward searches of lower-index saddles, thereby constructing the solution landscape systematically. The NPHiSD method searches along multiple efficient ascent directions by excluding the nullspace, which is the key for upward searches in degenerate problems. To reduce the cost of frequent nullspace updates, the search is divided into segments, within which the ascent directions remain orthogonal to the nullspace of the initial state of each segment. A sufficient and necessary condition for characterizing the segment that admits efficient ascent directions is proved. Extensive numerical experiments for typical problems such as Lifshitz-Petrich, Gross-Pitaevskii, and Lennard-Jones models are performed to show the universality and effectiveness of the NPHiSD method.

math.NA↗

arXiv2024

Nucleation and phase transition of decagonal quasicrystals

In this work, we study the nucleation of quasicrystals from liquid or periodic crystals by developing an efficient order-order phase transition algorithm, namely the nullspace-preserving saddle search method. Specifically, we focus on nucleation and phase transitions of the decagonal quasicrystal (DQC) based on the Lifshitz-Petrich model. We present the nucleation path of DQC from the liquid and demonstrate one- and two-stage transition paths between DQC and periodic crystals. We provide a perspective of the group-subgroup phase transition and nucleation rates to understand the nucleation and phase transition mechanisms involving DQC. These results reveal the one-step and stepwise modes of symmetry breaking or recovery in the phase transition from DQC, where the stepwise modes are more probable.

cond-mat.mtrl-sci↗

arXiv2023

Unusual Sign Reversal of Field-like Spin-Orbit Torque in Pt/Ni/Py with an Ultrathin Ni Spacer

The magnetization manipulation by spin-orbit torques (SOTs) in nonmagnetic-metal (NM)/ferromagnet (FM) heterostructures has provided great opportunities for spin devices. Besides the conventional spin Hall effect (SHE) in heavy metals with strong spin-orbit coupling, the orbital currents have been proposed to be another promising approach to generate strong SOTs. Here, we systematically study the SOTs efficiency and its dependence on the FM thickness and different NM/FM interfaces in two prototypical Pt/Py and Ta/Py systems by inserting an ultrathin magnetic layer (0.4 nm thick ML = Co, Fe, Gd, and Ni). The dampinglike (DL) torque efficiency $\xi_{DL}$ is significantly enhanced by inserting ultrathin Co, Fe, and Ni layers and is noticeably suppressed for the Gd insertion. Moreover, the Ni insertion results in a sign change of the field-like (FL) torque in Pt/Py and substantially reduces $\xi_{DL}$ in Ta/Py. These results are likely related to the additional spin currents generated by combining the orbital Hall effect (OHE) in the NM and orbital-to-spin conversion in the ML insertion layer and/or their interfaces, especially for the Ni insertion. Our results demonstrate that inserting ultrathin ML can effectively manipulate the strength and sign of the SOTs, which would be helpful for spintronics applications.

physics.app-ph↗

arXiv2023

An efficient saddle search method for ordered phase transitions involving translational invariance

In this work, we propose an efficient nullspace-preserving saddle search (NPSS) method for a class of phase transitions involving translational invariance, where the critical states are often degenerate. The NPSS method includes two stages, escaping from the basin and searching for the index-1 generalized saddle point. The NPSS method climbs upward from the generalized local minimum in segments to overcome the challenges of degeneracy. In each segment, an effective ascent direction is ensured by keeping this direction orthogonal to the nullspace of the initial state in this segment. This method can escape the basin quickly and converge to the transition states. We apply the NPSS method to the phase transitions between crystals, and between crystal and quasicrystal, based on the Landau-Brazovskii and Lifshitz-Petrich free energy functionals. Numerical results show a good performance of the NPSS method.

math.NA↗

arXiv2023

Excitation and voltage-gated modulation of single-mode dynamics in a planar nano-gap spin Hall nano-oscillator

We experimentally study the dynamical modes excited by current-induced spin-orbit torque and its electrostatic gating effect in a 3-terminal planar nano-gap spin Hall nano-oscillator (SHNO) with a moderate interfacial perpendicular magnetic anisotropy (IPMA). Both quasilinear propagating spin-wave and localized "bullet" modes are achieved and controlled by varying the applied in-plane magnetic field and driving current. The minimum linewidth shows a linear dependence on the actual temperature of the active area, confirming single-mode dynamics based on the nonlinear theory of spin-torque nano-oscillation with a single mode. The observed electrostatic gating tuning oscillation frequency arises from voltage-controlled magnetic anisotropy and threshold current of SHNO via modification of the nonlinear damping and/or the interfacial spin-orbit coupling of the magnetic multilayer. In contrast to previously observed two-mode coexistence degrading the spectral purity in Py/Pt-based SHNOs with a negligible IPMA, a single coherent spin-wave mode with a low driven current can be achieved by selecting the ferromagnet layer with a suitable IPMA because the nonlinear mode coupling can be diminished by bringing in the PMA field to compensate the easy-plane shape anisotropy. Moreover, the simulations demonstrate that the experimentally observed current and gate-voltage modulation of auto-oscillation modes are also closely associated with the nonlinear damping and mode coupling, which are determined by the ellipticity of magnetization precession. The demonstrated nonlinear mode coupling mechanism and electrical control approach of spin-wave modes could provide the clue to facilitate the implementation of the mutual synchronization map for neuromorphic computing applications in SHNO array networks.

cond-mat.mes-hall↗

arXiv2022

A multi-category inverse design neural network and its application to diblock copolymers

In this work, we design a multi-category inverse design neural network to map ordered periodic structure to physical parameters. The neural network model consists of two parts, a classifier and Structure-Parameter-Mapping (SPM) subnets. The classifier is used to identify structure, and the SPM subnets are used to predict physical parameters for desired structures. We also present an extensible reciprocal-space data augmentation method to guarantee the rotation and translation invariant of periodic structures. We apply the proposed network model and data augmentation method to two-dimensional diblock copolymers based on the Landau-Brazovskii model. Results show that the multi-category inverse design neural network is high accuracy in predicting physical parameters for desired structures. Moreover, the idea of multi-categorization can also be extended to other inverse design problems.

cond-mat.soft↗

arXiv2022

Current-driven magnetization dynamics and their correlation with magnetization configurations in perpendicularly magnetized tunnel junctions

We study spin-transfer-torque driven magnetization dynamics of a perpendicular magnetic tunnel junction (MTJ) nanopillar. Based on the combination of spin-torque ferromagnetic resonance and microwave spectroscopy techniques, we demonstrate that the free layer (FL) and the weak pinned reference layer (RL) exhibit distinct dynamic behaviors with opposite frequency vs. field dispersion relations. The FL can support a single coherent spin-wave (SW) mode for both parallel and antiparallel configurations, while the RL exhibits spin-wave excitation only for the antiparallel state. These two SW modes corresponding to the FL and RL coexist at an antiparallel state and exhibit a crossover phenomenon of oscillation frequency with increasing the external magnetic field, which could be helpful in the mutual synchronization of auto-oscillations for SW-based neuromorphic computing.

cond-mat.mes-hall↗

arXiv2022

Enhancement of spin-orbit torque efficiency by tailoring interfacial spin-orbit coupling in Pt-based magnetic multilayers

We study inserting Co layer thickness-dependent spin transport and spin-orbit torques (SOTs) in the Pt/Co/Py trilayers by spin-torque ferromagnetic resonance. The interfacial perpendicular magnetic anisotropy energy density ($K_s = 2.7~erg/cm^2$), which is dominated by interfacial spin-orbit coupling (ISOC) in the Pt/Co interface, total effective spin-mixing conductance ($G_{eff,tot} = 0.42 {\times} 10^{15}~Ω^{-1} m^{-2}$) and two-magnon scattering ($β_{TMS} = 0.46~nm^2$) are first characterized, and the damping-like torque ($ξ_{DL}$ = 0.103) and field-like torque ($ξ_{FL}$ = -0.017) efficiencies are also calculated quantitatively by varying the thickness of the inserting Co layer. The significant enhancement of $ξ_{DL}$ and $ξ_{FL}$ in Pt/Co/Py than Pt/Py bilayer system originates from the interfacial Rashba-Edelstein effect due to the strong ISOC between Co-3d and Pt-5d orbitals at the Pt/Co interface. Additionally, we find a considerable out-of-plane spin polarization SOT, which is ascribed to the spin anomalous Hall effect and possible spin precession effect due to IPMA-induced perpendicular magnetization at the Pt/Co interface. Our results demonstrate that the ISOC of the Pt/Co interface plays a vital role in spin transport and SOTs-generation. Our finds offer an alternative approach to improve the conventional SOTs efficiencies and generate unconventional SOTs with out-of-plane spin polarization to develop low power Pt-based spintronic via tailoring the Pt/FM interface.

cond-mat.mes-hall↗

arXiv2022

Multiferroic materials based on transition-metal dichalcogenides: Potential platform for reversible control of Dzyaloshinskii-Moriya interaction and skyrmion via electric field

Exploring novel two-dimensional multiferroic materials that can realize electric-field control of two-dimensional magnetism has become an emerging topic in spintronics. Using first-principles calculations, we demonstrate that non-metallic bilayer transition metal dichalcogenides (TMDs) can be an ideal platform for building multiferroics by intercalated magnetic atoms. Moreover, we unveil that with Co intercalated bilayer MoS2, Co(MoS2)2, two energetic degenerate states with opposite chirality of Dzyaloshinskii-Moriya interaction (DMI) are the ground states, indicating electric-field control of the chirality of topologic magnetism such as skyrmions can be realized in this type of materials by reversing the electric polarization. These findings pave the way for electric-field control of topological magnetism in two-dimensional multiferroics with intrinsic magnetoelectric coupling.

cond-mat.mtrl-sci↗

arXiv2022

Field free switching through bulk spin-orbit torque in L10-FePt films deposited on vicinal substrates

L10-FePt distinguishes itself for its ultrahigh perpendicular magnetic anisotropy (PMA), which enables memory cells with sufficient thermal stability to scale down to 3 nm. The recently discovered "bulk" spin-orbit torques in L10-FePt provide an efficient and scalable way to manipulate the L10-FePt magnetization. However, the existence of external field during the switching limits its practical application, and therefore field-free switching of the L10-FePt is in highly demand. In this manuscript, we demonstrate the field-free switching of the L10-FePt by growing it on vicinal MgO (001) substrates. This method is different from previously established strategies, as it does not need to add other functional layers or create asymmetry in the film structure. We demonstrate the field-free switching is robust and can withstand strong field disturbance up to ~1 kOe. The dependence on vicinal angle, film thickness, and growth temperature demonstrated a wide operation window for the field-free switching of the L10-FePt. We confirmed that the physical origin of the field-free switching is the vicinal surface-induced the tilted anisotropy of L10-FePt. We quantitatively characterize the spin-orbit torques in the L10-FePt films, and found the spin-orbit torques are not significantly influenced by the lattice strain from vicinal substrates. Our results extend beyond the established strategies to realize field-free switching, and potentially could be applied to other magnetic and antiferromagnetic systems.

cond-mat.mtrl-sci↗

arXiv2022

Large perpendicular magnetic anisotropy of transition metal dimers driven by polarization switching of two-dimensional ferroelectric In2Se3 substrate

Large perpendicular magnetic anisotropy (MA) is highly desirable for realizing atomic-scale magnetic data storage which represents the ultimate limit of the density of magnetic recording. In this work, we studied the MA of transition metal dimers Co-Os, Co-Co and Os-Os adsorbed on two-dimensional ferroelectric In2Se3 (In2Se3-CoOs, In2Se3-OsCo, In2Se3-CoCo and In2Se3-OsOs) by first-principles calculations. It is found that the Co-Os dimer in In2Se3-CoOs has large total perpendicular magnetic anisotropy energy (MAE) of ~ 40 meV. In particular, the MAE arising from Os atom is up to ~ 60 meV. The large MAE is attributed to the high spin-orbit coupling constant and the onefold coordination of Os atom. In addition, the MA of the dimers can be tuned by the polarization reversal of In2Se3. When the polarization is upward, the easy-axis directions of MA in In2Se3-OsCo, In2Se3-CoCo and In2Se3-OsOs are all in-plane, while the directions become perpendicular as the polarization is switched to downward. For the In2Se3-CoOs, switching polarization from upward to downward enhance the perpendicular MA from ~ 20 meV to ~ 40 meV. Based on the second-order perturbation theory, we confirm that the exchange splitting of dxy/dx2-y2 and dxz/dyz orbitals as well as the occupation of dz2 orbital at the vicinity of Fermi level play important roles in the changes of MA with the reversal of FE polarization of In2Se3.

cond-mat.mtrl-sci↗

arXiv2019

Angle-resolved broadband ferromagnetic resonance apparatus enabled through a spring-loaded sample mounting manipulator

Broadband ferromagnetic resonance is a useful technique to determine the magnetic anisotropy and study the magnetization dynamics of magnetic thin films. We report a spring-loaded sample loading manipulator for reliable sample mounting and rotation. The manipulator enables maximum signal, enhances system stability and is particularly useful for fully automated in-plane-field angle-resolved measurements. This angle-resolved broadband ferromagnetic resonance apparatus provides a viable method to study anisotropic damping and weak magnetic anisotropies, both vital for fundamental research and applications.

physics.app-ph↗

arXiv2018

Electrical switching of perpendicular magnetization in L10 FePt single layer

Electrical manipulation of magnetization is essential for integration of magnetic functionalities such as magnetic memories and magnetic logic devices into electronic circuits. The current induced spin-orbit torque (SOT) in heavy metal/ferromagnet (HM/FM) bilayers via the spin Hall effect in the HM and/or the Rashba effect at the interfaces provides an efficient way to switch the magnetization. In the meantime, current induced SOT has also been used to switch the in-plane magnetization in single layers such as ferromagnetic semiconductor (Ga,Mn)As and antiferromagnetic metal CuMnAs with globally or locally broken inversion symmetry. Here we demonstrate the current induced perpendicular magnetization switching in L10 FePt single layer. The current induced spin-orbit effective fields in L10 FePt increase with the chemical ordering parameter (S). In 20 nm FePt films with high S, we observe a large charge-to-spin conversion efficiency and a switching current density as low as 7.0E6 A/cm2. We anticipate our findings may stimulate the exploration of the spin-orbit torques in bulk perpendicular magnetic anisotropic materials and the application of high-efficient perpendicular magnetization switching in single FM layer.

cond-mat.mtrl-sci↗

arXiv2016

A versatile rotary-stage high frequency probe station for studying magnetic films and devices

We present a rotary-stage microwave probe station suitable for magnetic films and spintronic devices. Two stages, one for field rotation from parallel to perpendicular to the sample plane (Out-of-Plane) and the other intended for field rotation within the sample plane (In-Plane) have been designed. The sample, probes and micro positioners are rotated simultaneously with the stages, which allows the field orientation to cover $θ$ from 0 to $90^{\circ}$ and $φ$ from 0 to $360^{\circ}$. $θ$ and $φ$ being the angle between the direction of current flow and field in a Out-of-Plane and an In-Plane rotation, respectively. The operation frequency is up to 40 GHz and the magnetic field up to 1 T. The sample holder, vision system and probe assembly are compactly designed for the probes to land on a wafer with diameter up to 3$\,$cm. Using homemade multi-pin probes and commercially available high frequency probes, several applications including 4-probe DC measurements, the determination of domain wall velocity and spin transfer torque ferromagnetic resonance are demonstrated.

cond-mat.mtrl-sci↗