arXiv subjects

V. Yakovlev

Publications and source records attributed to V. Yakovlev.

40 records · Page 3Linked to original sources

arXiv2012

Study of effects of failure of beamline elements and their compensation in CW superconducting linac

Project-X is the proposed high intensity proton facility to be built at Fermilab, US. First stage of the Project-X consists of superconducting linac which will be operated in continuous wave (CW) mode to accelerate the beam from 2.5 MeV to 3 GeV. The operation at CW mode puts high tolerances on the beam line components, particularly on radiofrequency (RF) cavity. The failure of beam line elements at low energy is very critical as it results in mis-match of the beam with the following sections due to different beam parameters than designed parameter. It makes the beam unstable which causes emittance dilution, and ultimately results in beam losses. In worst case, it could affect the reliability of the machine and may lead to the shutdown of the Linac to replace the failed elements. Thus, it is important to study these effects and their compensation to get smooth beam propagation in linac. This paper describes the results of study performed for the failure of RF cavity & solenoid in SSR0 section.

physics.acc-ph↗

arXiv2012

Calculation of acceptance of high intensity superconducting proton linac for Project X

Project-X is the proposed high intensity proton facility to be built at Fermilab, US. Its Superconducting Linac, to be used at first stage of acceleration, will be operated in continuous wave (CW) mode. The Linac is divided into three sections on the basis of operating frequencies & six sections on the basis of family of RF cavities to be used for the acceleration of beam from 2.5 MeV to 3 GeV. The transition from one section to another can limit the acceptance of the Linac if these are not matched properly. We performed a study to calculate the acceptance of the Linac in both longitudinal and transverse plane. Investigation of most sensitive area which limits longitudinal acceptance and study of influence of failure of beam line elements at critical position, on acceptance are also performed.

physics.acc-ph↗

arXiv2012

CW RF system of the Project-X accelerator front end

Front end of a CW linac of the Project X contains an H source, an RFQ, a medium energy transport line with the beam chopper, and a SC low-beta linac that accelerates H- from 2.5 MeV to 160 MeV. SC Single Spoke Resonators (SSR) will be used in the linac, because Fermilab already successfully developed and tested a SSR for beta=0.21. Two manufactured cavities achieve 2.5 times more than design accelerating gradients. One of these cavities completely dressed, e.g. welded to helium vessel with integrated slow and fast tuners, and tested in CW regime. Successful tests of beta=0.21 SSR give us a confidence to use this type of cavity for low beta (0.117) and for high-beta (0.4) as well. Both types of these cavities are under development. In present report the basic constrains, parameters, electromagnetic and mechanical design for all the three SSR cavities, and first test results of beta=0.21 SSR are presented.

physics.acc-ph↗

arXiv2006

Fast Switching Ferroelectric Materials for Accelerator Applications

Fast switching (< 10 nsec) measurement results on the recently developed BST(M) (barium strontium titanium oxide composition with magnesium-based additions) ferroelectric materials are presented. These materials can be used as the basis for new advanced technology components suitable for high-gradient accelerators. A ferroelectric ceramic has an electric field-dependent dielectric permittivity that can be altered by applying a bias voltage. Ferroelectric materials offer significant benefits for linear collider applications, in particular, for switching and control elements where a very short response time of <10 nsec is required. The measurement results presented here show that the new BST(M) ceramic exhibits a high tunability factor: a bias field of 40-50 kV/cm reduces the permittivity by a factor of 1.3-1.5. The recently developed technology of gold biasing contact deposition on large diameter (110 cm) thin wall ferroelectric rings allowed ~few nsec switching times in witness sample experiments. The ferroelectric rings can be used at high pulsed power (tens of megawatts) for X-band components as well as at high average power in the range of a few kilowatts for the L-band phase-shifter, under development for optimization of the ILC rf coupling. Accelerator applications include fast active X-band and Ka-band high-power ferroelectric switches, high-power X-band and L-band phase shifters, and tunable dielectric-loaded accelerating structures.

physics.acc-ph↗