arXiv subjects

Vygantas Mizeikis

Publications and source records attributed to Vygantas Mizeikis.

8 recordsLinked to original sources

arXiv2026

High Entropy Alloy under Shock Compression: Optical-Pump X-Ray-Probe

High entropy alloys (HEAs) are multi-principal-element alloys designed for tailorable mechanical performance and have been attracting significant engineering interest, yet their fundamental behaviour under extreme dynamic conditions, such as shock loading, remains unexplored. Here, we report laser-shock experiments on two different types of 1-micrometers-thick HEA microfilms, CuPdAgPtAu and CrFeCoNiCuMo, on 25-micrometers-thick black-Kapton ablator driven by a high intensity laser pulse (532 nm, 5 ns, 16 J, 0.5-mm diameter focal spot) and probed by an X-ray free electron laser (XFEL) pulse (12 keV, 7 fs). Time-resolved X-ray diffraction (XRD) shows the formation of a transient phase with a lattice compression up to 5.1% of the CuPdAgPtAu HEA along the (111) plane; this transient compressed phase existed for 0.3 ns. The impedance matching Hugoniot analysis estimated a shock pressure of 55 +/- 6 GPa in the HEA film, while Au- and Fe-based equations of state (EoS) modelling predict 80 GPa (0.8 MBar) at the free HEA surface. The free HEA surface reached maximum velocities of ~ 5 km/s as recorded from in situ monitoring with the velocity interferometry system for any reflector (VISAR) imaging. These initial HEA results show the suitability of HEA sample preparation and XFEL-based XRD characterisation under extreme shock loading, and are promising for experimental determination of the EoS of this emerging class of materials (beamtime proposal No.: 2024A8503 for a 6-hour preliminary experiment).

cond-mat.mtrl-sci↗

arXiv2023

Determination of Stokes vector from a single image acquisition

Four Stokes parameters (1852) define the polarisation state of light. Measured changes of the Stokes vector of light traversing an inhomogeneous sample are linked to the local anisotropies of absorption and refraction and are harnessed over an increasing range of applications in photonics, material, and space/earth observation. Several independent polarisation sensitive measurements are usually required for determination of the all four Stokes parameters, which makes such characterisation procedure time-consuming or requires complex setups. Here we introduce a single-snapshot approach to Stokes polarimetry in transmission by use of a 4-polarisation camera with the on-chip integrated polarisers. A quarter-waveplate was added in front of the sample and was illuminated by a linearly polarised light. This approach is demonstrated by measuring birefringence $Δn\sim 0.012$ of spider silk of only $\sim 6~μ$m-diameter using microscopy, however, due to its generic nature, it is transferable to other spectral ranges and imaging applications, e.g., imaging from a fast moving satellite or drone or monitoring fast changing events such as phase transitions.

physics.optics↗

arXiv2019

Nanoscale optical and structural characterisation of silk

Background: Nanoscale composition of silk defining its unique properties via a hierarchical structural anisotropy has to be analysed at the highest spatial resolution of tens-of-nanometers corresponding to the size of fibrils made of b-sheets, which are the crystalline building blocks of silk. Results: Nanoscale optical and structural properties of silk have been measured from 100-nm thick longitudinal slices of silk fibers with ~10 nm resolution, the highest so far. Optical sub-wavelength resolution in hyperspectral mapping of absorbance and molecular orientation were carried out for comparison at IR wavelengths 2-10 micrometers using synchrotron radiation. Conclusion: Reliable distinction of transmission changes by only 1-2% due to anisotropy of amide bands was obtained from nano-thin slices of silk.

physics.app-ph↗

arXiv2018

Simple multi-wavelength imaging of birefringence: case study of silk

A polarised light imaging microscopy with an addition of liquid crystal (LC) phase retarder was implemented to determine the birefringence of silk fibers with the high 2 micrometers spatial resolution. The measurement was carried out with silk fiber (the optical slow axis) and the slow axis of the LC retarder set parallel (a perpendicular alignment can also be used). The direct fit of the transmission data provides a high fidelity determination of birefringence, $Dn = 1.63\times 10^{-2}$ (with 2% uncertainty) of the brown silk fiber (Antheraea pernyi) averaged over the wavelength range $l =$ (425-625) nm. By measuring retardance at four wavelengths it was possible to determine the true value of the birefringence of a thick sample when an optical path may include large number of wavelengths ($2p$ cycles in phase). The numerical procedures and required hardware are described for the do-it-yourself assembly of the imaging polariscope at a fractional budget compared with commercial units.

physics.ins-det↗

arXiv2017

Nanoscale chemical mapping of laser-solubilized silk

A water soluble amorphous form of silk was made by ultra-short laser pulse irradiation and detected by nanoscale IR mapping. An optical absorption-induced nanoscale surface expansion was probed to yield the spectral response of silk at IR molecular fingerprinting wavelengths with a high ~20 nm spatial resolution defined by the tip of the probe. Silk microtomed sections of 1-5 micrometers in thickness were prepared for nanoscale spectroscopy and a laser was used to induce amorphisation. Comparison of silk absorbance measurements carried out by table-top and synchrotron Fourier transform IR spectroscopy proved that chemical imaging obtained at high spatial resolution and specificity (able to discriminate between amorphous and crystalline silk) is reliably achieved by nanoscale IR. A nanoscale material characterization using synchrotron IR radiation is discussed.

physics.app-ph↗

arXiv2017

3D laser printing by ultra-short laser pulses for micro-optical applications: towards telecom wavelengths

Three dimensional (3D) fast (< 0.5 hour) printing of micro-optical elements down to sub-wavelength resolution over 100 micrometers footprint areas using femtosecond (fs-)laser oscillator is presented. Using sub-1 nJ pulse energies, optical vortex generators made of polymerised grating segments with an azimuthally changing orientation have been fabricated in SZ2080 resist; width of polymerised rods was ~150 nm and period 0.6-1 micrometers. Detailed phase retardance analysis was carried out manually with Berek compensator (under a white light illumination) and using an equivalent principle by an automated Abrio implementation at 546 nm. Direct experimental measurements of retardance was required since the period of the grating was comparable (or larger) than the wavelength of visible light. By gold sputtering, transmission-type optical vortex generators were turned into reflective ones with augmented retardance, n.h defined by the form birefringence, n, and the height h = 2d where d is the thickness of the polymerised structure. Retardance reached 315 nm as measured with Berek compensator at visible wavelengths. Birefringent phase delays of 180 degrees (or half-wavelength) required for high purity vortex generators can be made based on the proposed approach. Optical vortex generators for telecom wavelengths with sub-wavelength patterns of azimuthally oriented gratings are amenable by direct laser polymerisation.

physics.optics↗

arXiv2016

Nanoscale precision of 3D polymerisation via polarisation control

A systematic analysis of polarization effects in a direct write femtosecond laser 3D lithography is presented. It is newly shown that coupling between linear polarization of the writing light electric field and temperature gradient can be used to fine-tune feature sizes in structuring of photoresists at a nanoscale. The vectorial Debye focusing is used to simulate polarization effects and a controlled variation up to 20% in the linewidth is shown experimentally for the identical axial extent of the polymerised features. The revealed mechanisms are relevant for a wide range of phenomena of light-matter interaction at tight focusing in laser-tweezers and in plasmonic or dielectric sub-wavelength focusing where strong light intensity and thermal gradients coexist.

physics.optics↗

arXiv2002

Microfabrication of Three-Dimensional Structures in Polymer and Glass by Femtosecond Pulses

We report three-dimensional laser microfabrication, which enables microstructuring of materials on the scale of 0.2-1 micrometers. The two different types of microfabrication demonstrated and discussed in this work are based on holographic recording, and light-induced damage in transparent dielectric materials. Both techniques use nonlinear optical excitation of materials by ultrashort laser pulses (duration < 1 ps).

physics.optics↗