arXiv subjects

W. Zhang

Publications and source records attributed to W. Zhang.

At least 91 records · Page 5Linked to original sources

arXiv2020

Optical transceivers for event triggers in the ATLAS phase-I upgrade

The ATLAS phase-I upgrade aims to enhance event trigger performance in the Liquid Argon (LAr) calorimeter and the forward muon spectrometer. The trigger signals are transmitted by optical transceivers at 5.12 Gbps per channel in a radiation field. We report the design, quality control in production and ageing test of the transceivers fabricated with the LOCld laser driver and multi-mode 850 nm vertical-cavity surface-emitting laser (VCSEL). The modules are packaged in miniature formats of dual-channel transmitter (MTx) and transceiver (MTRx) for the LAr. The transmitters are also packaged in small form-factor pluggable (SFP) for the muon spectrometer. In production, the LOCld chips and VCSELs in TOSA package were examined before assembly. All of the modules were tested and selected during production for quality control based on the eye-diagram parameters measured at 5.12 Gbps. The yield is 98 % for both the MTx and MTRx on a total 4.7k modules. The uniformity of transmitter channels of a MTx was assured by choosing the TOSA components with approximately equal light powers. The ageing effect is monitored in burn-in of a small batch of transmitter modules with bit-error test and eye-diagrams measured periodically. The observables are stable with the light power degradation within 5 % over a period of more than 6k hours.

physics.ins-det↗

arXiv2020

A 4-Channel 10-Gbps/ch CMOS VCSEL Array Driver with on-chip Charge-pumps

We present the design and test results of a 4-channel 10-Gbps/ch Vertical-Cavity Surface-Emitting Laser array driver, the cpVLAD. With on-chip charge-pumps to extend the biasing headroom for the VCSELs needed for low temperature operation and mitigation of the radiation effects. The cpVLAD was fabricated in a 65-nm CMOS technology. The test results show that the cpVLAD is capable of driving VCSELs with forward bias voltages as high as 2.8 V from a 2.5 V power supply. The power consumption of the cpVLAD is 94 mW/ch.

physics.ins-det↗

arXiv2020

Constraining the transient high-energy activity of FRB180916.J0158+65 with Insight-HXMT followup observations

A link between magnetars and fast radio burst (FRB) sources has finally been established. In this context, one of the open issues is whether/which sources of extra galactic FRBs exhibit X/gamma-ray outbursts and whether it is correlated with radio activity. We aim to constrain possible X/gamma-ray burst activity from one of the nearest extragalactic FRB sources currently known over a broad energy range, by looking for bursts over a range of timescales and energies that are compatible with being powerful flares from extragalactic magnetars. We followed up the as-yet nearest extragalactic FRB source at a mere 149 Mpc distance, the periodic repeater FRB180916.J0158+65, during the active phase on February 4-7, 2020, with the Insight-Hard X-ray Modulation Telescope (HXMT). Taking advantage of the combination of broad band, large effective area, and several independent detectors available, we searched for bursts over a set of timescales from 1 ms to 1.024 s with a sensitive algorithm, that had previously been characterised and optimised. Moreover, through simulations we studied the sensitivity of our technique in the released energy-duration phase space for a set of synthetic flares and assuming different energy spectra. We constrain the possible occurrence of flares in the 1-100 keV energy band to E<10^46 erg for durations <0.1 s over several tens of ks exposure. We can rule out the occurrence of giant flares similar to the ones that were observed in the few cases of Galactic magnetars. The absence of reported radio activity during our observations does not allow us to make any statements on the possible simultaneous high-energy emission.

astro-ph.HE↗

arXiv2020

Intrinsic mechanism for anisotropic magnetoresistance and experimental confirmation in Co$_x$Fe$_{1-x}$ single-crystal films

Using first-principles transport calculations, we predict that the anisotropic magnetoresistance (AMR) of single-crystal Co$_x$Fe$_{1-x}$ alloys is strongly dependent on the current orientation and alloy concentration. An intrinsic mechanism for AMR is found to arise from the band crossing due to magnetization-dependent symmetry protection. These special $k$-points can be shifted towards or away from the Fermi energy by varying the alloy composition and hence the exchange splitting, thus allowing AMR tunability. The prediction is confirmed by delicate transport measurements, which further reveal a reciprocal relationship of the longitudinal and transverse resistivities along different crystal axes.

cond-mat.mtrl-sci↗

arXiv2020

Design and hardware evaluation of the optical-link system for the ATLAS Liquid Argon Calorimeter Phase-II Upgrade

An optical link system is being developed for the ATLAS Liquid Argon Calorimeter Phase-II upgrade. The optical link system is responsible for transmit the data of over 182 thousand detector channels from 1524 Front-End Boards (FEBs) through 26 optical fibers per FEB over 150 meters to the counting room and brings clocks, bunch crossing reset signals and slow control/monitoring signals back to the FEBs. The optical link system is based on the Low-Power GigaBit Transceivers (lpGBTs) and the Versatile optical Transceiver (VTRx+) modules, which both are being developed for the High-Luminosity LHC upgrade. An evaluation board is designed and the major functions of the optical link system are being evaluated. The design of the optical link system and the evaluation of major functions are presented in the paper.

physics.ins-det↗

arXiv2020

An Evolutional Algorithm for Automatic 2D Layer Segmentation in Laser-aided Additive Manufacturing

Toolpath planning is an important task in laser aided additive manufacturing (LAAM) and other direct energy deposition (DED) processes. The deposition toolpaths for complex geometries with slender structures can be further optimized by partitioning the sliced 2D layers into sub-regions, and enable the design of appropriate infill toolpaths for different sub-regions. However, reported approaches for 2D layer segmentation generally require manual operations that are tedious and time-consuming. To increase segmentation efficiency, this paper proposes an autonomous approach based on evolutional computation for 2D layer segmentation. The algorithm works in an identify-and-segment manner. Specifically, the largest quasi-quadrilateral is identified and segmented from the target layer iteratively. Results from case studies have validated the effectiveness and efficacy of the developed algorithm. To further improve its performance, a roughing-finishing strategy is proposed. Via multi-processing, the strategy can remarkably increase the solution variety without affecting solution quality and search time, thus providing great application potential in LAAM toolpath planning. To the best of the authors knowledge, this work is the first to address automatic 2D layer segmentation problem in LAAM process. Therefore, it may be a valuable supplement to the state of the art in this area.

cs.GR↗

arXiv2020

Stabilization of antiferromagnetism in 1T-Fe$_{0.05}$TaS$_2$

1T-TaS$_2$ is a prototypical charge-density-wave (CDW) system with a Mott insulating ground state. Usually, a Mott insulator is accompanied by an antiferromagnetic state. However, the antiferromagnetic order had never been observed in 1T-TaS$_2$. Here, we report the stabilization of the antiferromagnetic order by the intercalation of a small amount of Fe into the van der Waals gap of 1T-TaS$_2$, i.e. forming 1T-Fe$_{0.05}$TaS$_2$. Upon cooling from 300~K, the electrical resistivity increases with a decreasing temperature before reaching a maximum value at around 15~K, which is close to the Neel temperature determined from our magnetic susceptibility measurement. The antiferromagnetic state can be fully suppressed when the sample thickness is reduced, indicating that the antiferromagnetic order in Fe$_{0.05}$TaS$_2$ has a non-negligible three-dimensional character. For the bulk Fe$_{0.05}$TaS$_2$, a comparison of our high pressure electrical transport data with that of 1T-TaS$_2$ indicates that, at ambient pressure, Fe$_{0.05}$TaS$_2$ is in the nearly commensurate charge-density-wave (NCCDW) phase near the border of the Mott insulating state. The temperature-pressure phase diagram thus reveals an interesting decoupling of the antiferromagnetism from the Mott insulating state.

cond-mat.str-el↗

arXiv2020

High-Temperature Charge-Stripe Correlations in La$_{1.675}$Eu$_{0.2}$Sr$_{0.125}$CuO$_4$

We use resonant inelastic x-ray scattering to investigate charge-stripe correlations in La$_{1.675}$Eu$_{0.2}$Sr$_{0.125}$CuO$_4$. By differentiating elastic from inelastic scattering, it is demonstrated that charge-stripe correlations precede both the structural low-temperature tetragonal phase and the transport-defined pseudogap onset. The scattering peak amplitude from charge stripes decays approximately as $T^{-2}$ towards our detection limit. The in-plane integrated intensity, however, remains roughly temperature independent. Therefore, although the incommensurability shows a remarkably large increase at high temperature, our results are interpreted via a single scattering constituent. In fact, direct comparison to other stripe-ordered compounds (La$_{1.875}$Ba$_{0.125}$CuO$_4$, La$_{1.475}$Nd$_{0.4}$Sr$_{0.125}$CuO$_4$ and La$_{1.875}$Sr$_{0.125}$CuO$_4$) suggests a roughly constant integrated scattering intensity across all these compounds. Our results therefore provide a unifying picture for the charge-stripe ordering in La-based cuprates. As charge correlations in La$_{1.675}$Eu$_{0.2}$Sr$_{0.125}$CuO$_4$ extend beyond the low-temperature tetragonal and pseudogap phase, their emergence heralds a spontaneous symmetry breaking in this compound.

cond-mat.supr-con↗

arXiv2020

Evolution of safety factor profiles in sawteeth

Two different definitions of the safety factor are applied to investigate the evolution of the safety factor profile during normal sawteeth, the stationary state, and the incomplete reconnection. It is found that the safety factor profiles from the old definition are sometimes inconsistent with the Poincare plots of the magnetic field during sawteeth. The old safety factor always indicates that the safety factor around the magnetic axis is flattened and equal to 1.0 with the development of the kink instability. However, the Poincare plots of the magnetic field lines indicate that the topology of the magnetic field around the magnetic axis has not been changed. To solve the inconsistency, we propose a new definition of the safety factor, in which the poloidal angle relative to the new twisted magnetic axis is used instead of the poloidal angle to the original axis. With the new definition, the safety factor profiles are consistent with Poincare plots of the magnetic field. We also find that the safety factor profiles are significantly different from the two different q definitions. With the new q definition, the safety factor at the magnetic axis q0 remains unchanged in almost the entire period of a sawtooth and jumps up to 1.0 near the end during normal sawteeth; in the non-axisymmetric equilibrium, q0 is still far below 1.0; q0 remains its initial value throughout the incomplete reconnection.

physics.plasm-ph↗

arXiv2020

Bi2W2O9: a potentially antiferroelectric Aurivillius phase

Ferroelectric tungsten-based Aurivillius oxides are naturally stable superlattice structures, in which A-site deficient perovskite blocks [WnO3n+1]-2 (n = 1, 2, 3, ...) interleave with fluorite-like bismuth oxide layers [Bi2O2]+2 along the c -axis. In the n = 2 Bi2W2O9 phase, an in-plane antipolar distortion dominates but there has been controversy as to the ground state symmetry. Here we show, using a combination of first-principles density functional theory calculations and experiments, that the ground state is a non-polar phase of Pnab symmetry. We explore the energetics of metastable phases and the potential for antiferroelectricity in this n=2 Aurivillius phase.

cond-mat.mtrl-sci↗

arXiv2020

Detection of hole pockets in the candidate type-II Weyl semimetal MoTe$_2$ from Shubnikov-de Haas quantum oscillations

The bulk electronic structure of $T_d$-MoTe$_2$ features large hole Fermi pockets at the Brillouin zone center ($Γ$) and two electron Fermi surfaces along the $Γ-X$ direction. However, the large hole pockets, whose existence has important implications for the Weyl physics of $T_d$-MoTe$_2$, has never been conclusively detected in quantum oscillations. This raises doubt about the realizability of Majorana states in $T_d$-MoTe$_2$, because these exotic states rely on the existence of Weyl points, which originated from the same band structure predicted by density functional theory (DFT). Here, we report an unambiguous detection of these elusive hole pockets via Shubnikov-de Haas (SdH) quantum oscillations. At ambient pressure, the quantum oscillation frequencies for these pockets are 988 T and 1513 T, when the magnetic field is applied along the $c$-axis. The quasiparticle effective masses $m^*$ associated with these frequencies are 1.50 $m_e$ and 2.77 $m_e$, respectively, indicating the importance of Coulomb interactions in this system. We further measure the SdH oscillations under pressure. At 13 kbar, we detected a peak at 1798 T with $m^*$ = 2.86 $m_e$. Relative to the oscillation data at a lower pressure, the amplitude of this peak experienced an enhancement, which can be attributed to the reduced curvature of the hole pockets under pressure. Combining our experimental data with DFT + $U$ calculations, where $U$ is the Hubbard parameter, our results shed light on why these important hole pockets have not been detected until now.

cond-mat.supr-con↗

arXiv2020

Engineering Co$_2$MnAl$_x$Si$_{1-x}$ Heusler compounds as a model system to correlate spin polarization, intrinsic Gilbert damping and ultrafast demagnetization

Engineering of magnetic materials for developing better spintronic applications relies on the control of two key parameters: the spin polarization and the Gilbert damping responsible for the spin angular momentum dissipation. Both of them are expected to affect the ultrafast magnetization dynamics occurring on the femtosecond time scale. Here, we use engineered Co2MnAlxSi1-x Heusler compounds to adjust the degree of spin polarization P from 60 to 100% and investigate how it correlates with the damping. We demonstrate experimentally that the damping decreases when increasing the spin polarization from 1.1 10-3 for Co2MnAl with 63% spin polarization to an ultra-low value of 4.10-4 for the half-metal magnet Co2MnSi. This allows us investigating the relation between these two parameters and the ultrafast demagnetization time characterizing the loss of magnetization occurring after femtosecond laser pulse excitation. The demagnetization time is observed to be inversely proportional to 1-P and as a consequence to the magnetic damping, which can be attributed to the similarity of the spin angular momentum dissipation processes responsible for these two effects. Altogether, our high quality Heusler compounds allow controlling the band structure and therefore the channel for spin angular momentum dissipation.

cond-mat.mtrl-sci↗

arXiv2019

Diagnostic of the spectral properties of Aquila X-1 by Insight-HXMT snapshots during the early propeller phase

We study the 2018 outburst of Aql X-1 via the monitor of all sky X-ray image (MAXI) data. We show that the outburst starting in February 2018 is a member of short-low class in the frame of outburst duration and the peak count rate although the outburst morphology is slightly different from the other fast-rise-exponential-decay (FRED) type outbursts with a milder rising stage. We study the partial accretion in the weak propeller stage of Aql X-1 via the MAXI data of the 2018 outburst. We report on the spectral analysis of 3 observations of Aquila X-1 obtained by Insight - hard X-ray modulation telescope (Insight-HXMT) during the late decay stage of the 2018 outburst. We discuss that the data taken by Insight-HXMT is just after the transition to the weak propeller stage. Our analysis shows the necessity of a comptonization component to take into account the existence of an electron cloud resulting photons partly up-scattered.

astro-ph.HE↗

arXiv2019

Constraints on the binary black hole hypothesis for system LB-1

At about 70 solar masses, the recently-discovered dark object orbited by a B-type star in the system LB-1 is difficult to understand as the end point of standard stellar evolution, except as a binary black hole (BBH). LB-1 shows a strong, broad H-alpha emission line that is best attributed to a gaseous disk surrounding the dark mass. We use the observed H-alpha line shape, particularly its wing extension, to constrain the inner radius of the disk and thereby the separation of a putative BBH. The hypothesis of a current BBH is effectively ruled out on the grounds that its merger time must be a small fraction of the current age of the B star. The hypothesis of a previous BBH that merged to create the current dark mass is also effectively ruled out by the low orbital eccentricity, due to the combination of mass loss and kick resulted from gravitational wave emission in any past merger. We conclude that the current dark mass is a single black hole produced by the highly mass-conserving, monolithic collapse of a massive star.

astro-ph.SR↗

arXiv2019

The Castro AMR Simulation Code: Current and Future Developments

We describe recent developments to the Castro astrophysics simulation code, focusing on new features that enable our simulations of X-ray bursts. Two highlights of Castro's ongoing development are the new integration technique to couple hydrodynamics and reactions to high order and GPU offloading. We discuss how these features will help offset some of the computational expense in X-ray burst models.

astro-ph.IM↗

arXiv2019

Insight-HXMT observation on 4U~1608--52: evolving spectral properties of a bright type-I X-ray burst

The evidences for the influence of thermonuclear (type-I) X-ray bursts upon the surrounding environments in neutron star low-mass X-ray binaries (LMXB) were detected previously via spectral and timing analyses. Benefitting from a broad energy coverage of Insight-HXMT, we analyze one photospheric radius expansion (PRE) burst, and find an emission excess at soft X-rays. Our spectral analysis shows that, such an excess is not likely relevant to the disk reflection induced by the burst emission and can be attributed to an enhanced pre-burst/persistent emission. We find that the burst and enhanced persistent emissions sum up to exceed Eddington luminosity by $\sim$ 40 percentages. We speculate that the enhanced emission is from a region beyond the PRE radius, or through the Comptonization of the corona.

astro-ph.HE↗

arXiv2019

$Insight$-HXMT study of the timing properties of Sco X-1

We present a detailed timing study of the brightest persistent X-ray source Sco X-1 using the data collected by the Hard X-ray Modulation Telescope ($Insight$-HXMT) from July 2017 to August 2018. A complete $Z$-track hardness-intensity diagram (HID) is obtained. The normal branch oscillations (NBOs) at $\sim$ 6 Hz in the lower part of the normal branch (NB) and the flare branch oscillations (FBOs) at $\sim$ 16 Hz in the beginning part of the flaring branch (FB) are found in observations with the Low Energy X-ray Telescope (LE) and the Medium Energy X-ray Telescope (ME) of $Insight$-HXMT, while the horizontal branch oscillations (HBOs) at $\sim$ 40 Hz and the kilohertz quasi-periodic oscillations (kHz QPOs) at $\sim$ 800 Hz are found simultaneously up to 60 keV for the first time on the horizontal branch (HB) by the High Energy X-ray Telescope (HE) and ME. We find that for all types of the observed QPOs, the centroid frequencies are independent of energy, while the root mean square (rms) increases with energy; the centroid frequencies of both the HBOs and kHz QPOs increase along the $Z$-track from the top to the bottom of the HB; and the NBOs show soft phase lags increasing with energy. A continuous QPO transition from the FB to NB in $\sim$ 200 s are also detected. Our results indicate that the non-thermal emission is the origin of all types of QPOs, the innermost region of the accretion disk is non-thermal in nature, and the corona is nonhomogeneous geometrically.

astro-ph.HE↗

arXiv2019

Insight-HXMT observations of 4U~1636-536: Corona cooling revealed with single short type-I X-ray burst

Corona cooling was detected previously from stacking a series of short type-I bursts occurred during the low/had state of atoll outburst. Type-I bursts are hence regarded as sharp probe to our better understanding on the basic property of the corona. The launch of the first Chinese X-ray satellite Insight-HXMT has large detection area at hard X-rays which provide almost unique chance to move further in this research field. We report the first detection of the corona cooling by Insight-HXMT from single short type-I burst showing up during {\bf flare} of 4U 1636-536. This type-I X-ray burst has a duration of $\sim$13 seconds and hard X-ray shortage is detected with significance 6.2~$σ$ in 40-70 keV. A cross-correlation analysis between the lightcurves of soft and hard X-ray band, shows that the corona shortage lag the burst emission by 1.6 $\pm$1.2~s. These results are consistent with those derived previously from stacking a large amount of bursts detected by RXTE/PCA within a series of {\bf flares} of 4U 1636-536. Moreover, the broad bandwidth of Insight-HXMT allows as well for the first time to infer the burst influence upon the continuum spectrum via performing the spectral fitting of the burst, which ends up with the finding that hard X-ray shortage appears at around 40 keV in the continuum spectrum. These results suggest that the evolution of the corona along with the outburst{\bf /flare} of NS XRB may be traced via looking into a series of embedded type-I bursts by using Insight-HXMT.

astro-ph.HE↗