arXiv subjects

Yana Vaynzof

Publications and source records attributed to Yana Vaynzof.

At least 37 records · Page 2Linked to original sources

arXiv2024

Semitransparent perovskite solar cells with an evaporated ultra-thin perovskite absorber

Metal halide perovskites are of great interest for application in semitransparent solar cells due to their tunable bandgap and high performance. However, fabricating high-efficiency perovskite semitransparent devices with high average visible transmittance (AVT) is challenging because of their high absorption coefficient. Here, we adopt a co-evaporation process to fabricate ultrathin CsPbI3 perovskite films. Due to the smooth surface and orientated crystal growth of the evaporated perovskite films, we are able to achieve 10 nm thin films with compact and continuous morphology without pinholes. When integrated into a p-i-n device structure of glass/ITO/PTAA/perovskite/PCBM/BCP/Al/Ag with an optimized transparent electrode, these ultrathin layers result in an impressive open-circuit voltage (VOC) of 1.08 V and a fill factor (FF) of 80%. Consequently, a power conversion efficiency of 3.6% with an AVT above 50% is demonstrated, achieved in the 10 nm semitransparent perovskite solar cells, which is the first report for a perovskite device of 10 nm active layer with higher VOC, FF and AVT. These findings demonstrate that evaporation process is a possible way for compact ultrathin perovskite film, which has the potential for future smart windows, light emitting diodes, and tandem device applications.

cond-mat.mtrl-sci↗

arXiv2024

Analysis of the Annealing Budget of Metal Oxide Thin-Film Transistors Prepared by an Aqueous Blade-Coating Process

Metal oxide (MO) semiconductors are widely used in electronic devices due to their high optical transmittance and promising electrical performance. This work describes the advancement toward an eco-friendly, streamlined method for preparing thin-film transistors (TFTs) via a pure water-solution blade-coating process with focus on a low thermal budget. Low temperature and rapid annealing of triple-coated indium oxide thin-film transistors (3C-TFTs) and indium oxide/zinc oxide/indium oxide thin-film transistors (IZI-TFTs) on a 300 nm SiO2 gate dielectric at 300 $^{\circ}$C for only 60 s yields devices with an average field effect mobility of 10.7 and 13.8 cm2/Vs, respectively. The devices show an excellent on/off ratio (>10^6), and a threshold voltage close to 0 V when measured in air. Flexible MO-TFTs on polyimide substrates with AlOx dielectrics fabricated by rapid annealing treatment can achieve a remarkable mobility of over 10 cm2/Vs at low operating voltage. When using a longer post-coating annealing period of 20 min, high-performance 3C-TFTs (over 18 cm2/Vs) and IZI-TFTs (over 38 cm2/Vs) using MO semiconductor layers annealed at 300 $^{\circ}$C are achieved.

physics.app-ph↗

arXiv2024

Alloyed Re$_x$Mo$_{1-x}$S$_2$ Nanoflakes with Enlarged Interlayer Distances for Hydrogen Evolution

Molybdenum sulfide (MoS$_2$) has attracted significant attention due to its great potential as a low-cost and efficient catalyst for the hydrogen evolution reaction. Developing a facile, easily upscalable, and inexpensive approach to produce catalytically active nanostructured MoS$_2$ with a high yield would significantly advance its practical application. Colloidal synthesis offers several advantages over other preparation techniques to overcome the low reaction yield of exfoliation and drawbacks of expensive equipment and processes used in chemical vapor deposition. In this work, we report an efficient synthesis of alloyed Re$_x$Mo$_{1-x}$S$_2$ nanoflakes with an enlarged interlayer distance, among which the composition Re$_{0.55}$Mo$_{0.45}$S$_2$ exhibits excellent catalytic performance with overpotentials as low as 79 mV at 10 mA/cm2 and a small Tafel slope of 42 mV/dec. Density functional theory calculations prove that enlarging the distance between layers in the Re$_x$Mo$_{1-x}$S$_2$alloy can greatly improve its catalytic performance due to a significantly reduced free energy of hydrogen adsorption. The developed approach paves the way to design advanced transition metal dichalcogenide-based catalysts for hydrogen evolution and to promote their large-scale practical application.

cond-mat.mtrl-sci↗

arXiv2024

Elucidating Structure Formation in Highly Oriented Triple Cation Perovskite Films

Metal halide perovskites are an emerging class of crystalline semiconductors of great interest for application in optoelectronics. Their properties are dictated not only by their composition, but also by their crystalline structure and microstructure. While significant efforts were dedicated to the development of strategies for microstructural control, significantly less is known about the processes that govern the formation of their crystalline structure in thin films, in particular in the context of crystalline orientation. In this work, we investigate the formation of highly oriented triple cation perovskite films fabricated by utilizing a range of alcohols as an antisolvent. Examining the film formation by in-situ grazing-incidence wide-angle X-ray scattering reveals the presence of a short-lived highly oriented crystalline intermediate, which we identify as FAI-PbI2-xDMSO. The intermediate phase templates the crystallisation of the perovskite layer, resulting in highly oriented perovskite layers. The formation of this DMSO containing intermediate is triggered by the selective removal of DMF when alcohols are used as an antisolvent, consequently leading to differing degrees of orientation depending on the antisolvent properties. Finally, we demonstrate that photovoltaic devices fabricated from the highly oriented films, are superior to those with a random polycrystalline structure in terms of both performance and stability.

physics.app-ph↗

arXiv2024

Sonication-assisted liquid phase exfoliation of two-dimensional CrTe$_3$ under inert conditions

Liquid phase exfoliation (LPE) has been used for the successful fabrication of nanosheets from a large number of van der Waals materials. While this allows to study fundamental changes of material properties' associated with reduced dimensions, it also changes the chemistry of many materials due to a significant increase of the effective surface area, often accompanied with enhanced reactivity and accelerated oxidation. To prevent material decomposition, LPE and processing in inert atmosphere have been developed, which enables the preparation of pristine nanomaterials, and to systematically study compositional changes over time for different storage conditions. Here, we demonstrate the inert exfoliation of the oxidation-sensitive van der Waals crystal, CrTe$_3$. The pristine nanomaterial was purified and size-selected by centrifugation, nanosheet dimensions in the fractions quantified by atomic force microscopy and studied by Raman, X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDX) and photo spectroscopic measurements. We find a dependence of the relative intensities of the CrTe$_3$ Raman modes on the propagation direction of the incident light, which prevents a correlation of the Raman spectral profile to the nanosheet dimensions. XPS and EDX reveal that the contribution of surface oxides to the spectra is reduced after exfoliation compared to the bulk material. Further, the decomposition mechanism of the nanosheets was studied by time-dependent extinction measurements after water titration experiments to initially dry solvents, which suggest that water plays a significant role in the material decomposition.

cond-mat.mtrl-sci↗

arXiv2024

Photoluminescence Mapping over Laser Pulse Fluence and Repetition Rate as a Fingerprint of Charge and Defect Dynamics in Perovskites

Defects in metal halide perovskites (MHP) are photosensitive, making the observer effect unavoidable when laser spectroscopy methods are applied. Photoluminescence (PL) bleaching and enhancement under light soaking and recovery in dark are examples of the transient phenomena that are consequent to the creation and healing of defects. Depending on the initial sample composition, environment, and other factors, the defect nature and evolution can strongly vary, making spectroscopic data analysis prone to misinterpretations. Herein, the use of an automatically acquired dependence of PL quantum yield (PLQY) on the laser pulse repetition rate and pulse fluence as a unique fingerprint of both charge carrier dynamics and defect evolution is demonstrated. A simple visual comparison of such fingerprints allows for assessment of similarities and differences between MHP samples. The study illustrates this by examining methylammonium lead triiodide (MAPbI3) films with altered stoichiometry that just after preparation showed very pronounced defect dynamics at time scale from milliseconds to seconds, clearly distorting the PLQY fingerprint. Upon weeks of storage, the sample fingerprints evolve toward the standard stoichiometric MAPbI3 in terms of both charge carrier dynamics and defect stability. Automatic PLQY mapping can be used as a universal method for assessment of perovskite sample quality.

physics.app-ph↗

arXiv2024

High-efficiency perovskite-organic blend light-emitting diodes featuring self-assembled monolayers as hole-injecting interlayers

The high photoluminescence efficiency, color purity, extended gamut, and solution processability make low-dimensional hybrid perovskites attractive for light-emitting diode (PeLED) applications. However, controlling the microstructure of these materials to improve the device performance remains challenging. Here, the development of highly efficient green PeLEDs based on blends of the quasi-2D (q2D) perovskite, PEA2Cs4Pb5Br16, and the wide bandgap organic semiconductor 2,7 dioctyl[1] benzothieno[3,2-b]benzothiophene (C8-BTBT) is reported. The presence of C8-BTBT enables the formation of single-crystal-like q2D PEA2Cs4Pb5Br16 domains that are uniform and highly luminescent. Combining the PEA2Cs4Pb5Br16:C8-BTBT with self-assembled monolayers (SAMs) as hole-injecting layers (HILs), yields green PeLEDs with greatly enhanced performance characteristics, including external quantum efficiency up to 18.6%, current efficiency up to 46.3 cd/A, the luminance of 45 276 cd m^-2, and improved operational stability compared to neat PeLEDs. The enhanced performance originates from multiple synergistic effects, including enhanced hole-injection enabled by the SAM HILs, the single crystal-like quality of the perovskite phase, and the reduced concentration of electronic defects. This work highlights perovskite:organic blends as promising systems for use in LEDs, while the use of SAM HILs creates new opportunities toward simpler and more stable PeLEDs.

physics.app-ph↗

arXiv2024

Band Structure Engineering in Highly Crystalline Organic Semiconductors

Blending of semiconductors for controlling the energy levels (band structure engineering) is an important technique, in particular, for optoelectronic applications. The underlying physics is the delocalized Bloch states, which average over the potential landscape of the blend. For organic semiconductors, it has been shown that two quite different effects, the dielectric constant and electrostatic interaction between molecules, can be used to tune the energy gap and ionization energy of disordered and weakly crystalline organic semiconductor blends. It is so far not known whether the electronic delocalization in organic crystals with large bandwidths can contribute to the energy structure engineering of the blend in a way similar to that in inorganic semiconductors. Here, we investigate the growth of highly ordered organic thin-film blends with a similar chemical structure and show the effect of band structure engineering by spectroscopic methods. We rationalize the experimental results with comprehensive theoretical simulations, showing that the delocalization is a significant effect. Our work paves the way for engineering the band structure of highly ordered organic semiconductor thin films that can be tailored for the desired optoelectronic device application.

cond-mat.mtrl-sci↗

arXiv2024

Ultrafast Vibrational Control of Hybrid Perovskite Devices Reveals the Influence of the Organic Cation on Electronic Dynamics

Vibrational control (VC) of photochemistry through the optical stimulation of structural dynamics is a nascent concept only recently demonstrated for model molecules in solution. Extending VC to state-of-the-art materials may lead to new applications and improved performance for optoelectronic devices. Metal halide perovskites are promising targets for VC due to their mechanical softness and the rich array of vibrational motions of both their inorganic and organic sublattices. Here, we demonstrate the ultrafast VC of FAPbBr3 perovskite solar cells via intramolecular vibrations of the formamidinium cation using spectroscopic techniques based on vibrationally promoted electronic resonance. The observed short (~300 fs) time window of VC highlights the fast dynamics of coupling between the cation and inorganic sublattice. First-principles modelling reveals that this coupling is mediated by hydrogen bonds that modulate both lead halide lattice and electronic states. Cation dynamics modulating this coupling may suppress non-radiative recombination in perovskites, leading to photovoltaics with reduced voltage losses.

physics.app-ph↗

arXiv2024

Influence of chemical interactions on the electronic properties of BiOI/organic semiconductor heterojunctions for application in solution-processed electronics

Bismuth oxide iodide (BiOI) has been viewed as a suitable environmentally-friendly alternative to lead-halide perovskites for low-cost (opto-)electronic applications such as photodetectors, phototransistors and sensors. To enable its incorporation in these devices in a convenient, scalable, and economical way, BiOI thin films were investigated as part of heterojunctions with various p-type organic semiconductors (OSCs) and tested in a field-effect transistor (FET) configuration. The hybrid heterojunctions, which combine the respective functionalities of BiOI and the OSCs were processed from solution under ambient atmosphere. The characteristics of each of these hybrid systems were correlated with the physical and chemical properties of the respective materials using a concept based on heteropolar chemical interactions at the interface. Systems suitable for application in lateral transport devices were identified and it was demonstrated how materials in the hybrids interact to provide improved and synergistic properties. These indentified heterojunction FETs are a first instance of successful incorporation of solution-processed BiOI thin films in a three-terminal device. They show a significant threshold voltage shift and retained carrier mobility compared to pristine OSC devices and open up possibilities for future optoelectronic applications.

physics.app-ph↗

arXiv2024

Cation exchange synthesis of AgBiS$_2$ quantum dots for highly efficient solar cells

Silver bismuth sulfide (AgBiS$_2$) nanocrystals have emerged as a promising eco-friendly, low-cost solar cell absorber material. Their direct synthesis often relies on the hot-injection method, requiring the application of high temperatures and vacuum for prolonged times. Here, we demonstrate an alternative synthetic approach via a cation exchange reaction. In the first-step, bis(stearoyl)sulfide is used as an air-stable sulfur precursor for the synthesis of small, monodisperse Ag2S nanocrystals at room-temperature. In a second step, bismuth cations are incorporated into the nanocrystal lattice to form ternary AgBiS$_2$ nanocrystals, without altering their size and shape. When implemented into photovoltaic devices, AgBiS$_2$ nanocrystals obtained by cation exchange reach power conversion efficiencies of up to 7.35%, demonstrating the efficacy of the new synthetic approach for the formation of high-quality, ternary semiconducting nanocrystals.

cond-mat.mtrl-sci↗

arXiv2024

Cobalt-based Co$_3$Mo3N/Co$_4$N/Co Metallic Heterostructure as a Highly Active Electrocatalyst for Alkaline Overall Water Splitting

Alkaline water electrolysis is considered a commercially viable option for large-scale hydrogen production. However, this process still faces challenges due to the high voltage (>1.65 V at 10 mA cm$^{-2}$) and its limited stability at higher current densities due to the inefficient electron transport kinetics. Herein, a novel cobalt based metallic heterostructure (Co$_3$Mo3N/Co$_4$N/Co/Co) is designed for application for water electrolysis. Operando Raman experiments reveal that the formation of Co$_3$Mo3N/Co$_4$N/Co heterointerface boosts the free water adsorption and dissociation, resulting in a surplus of protons available for subsequent hydrogen production. Furthermore, the altered electronic structure of Co$_3$Mo3N/Co$_4$N/Co heterointerface optimizes the ΔGH of nitrogen atoms at the interface. This synergistic effect between interfacial nitrogen atoms and metal phase cobalt creates highly efficient hydrogen evolution reaction (HER) active sites, thereby enhancing the overall performance. Additionally, the heterostructure exhibits a rapid OH- adsorption rate, coupled with a strong adsorption strength, leading to improved oxygen evolution reaction (OER) performance. Crucially, the metallic heterojunction facilitates fast electron transport, expediting the aforementioned reaction steps and ultimately improving the overall efficiency of water splitting. The water electrolyzer with Co$_3$Mo3N/Co$_4$N/Co/Co as a catalyst exhibits outstanding performance, requiring an impressively low cell voltage of 1.58 V at 10 mA cm$^{-2}$ and maintaining approximately 100% retention over a remarkable 100 h duration at 200 mA cm$^{-2}$. This performance significantly exceeds that of the commercial Pt/C || RuO2 electrolyzer.

physics.app-ph↗

arXiv2024

On-liquid-gallium surface synthesis of ultra-smooth conductive metal-organic framework thin films

Conductive metal-organic frameworks (MOFs) are emerging electroactive materials for (opto-)electronics. However, it remains a great challenge to achieve reliable MOF-based devices via the existing synthesis methods that are compatible with the complementary metal-oxide-semiconductor technology, as the surface roughness of thus-far synthetic MOF films or pellets is rather high for efficient electrode contact. Here, we develop an on-liquid-gallium surface synthesis (OLGSS) strategy under chemical vapor deposition (CVD) conditions for the controlled growth of two-dimensional conjugated MOF (2D c-MOF) thin films with ten-fold improvement of surface flatness (surface roughness can reach as low as ~2 Å) compared with MOF films grown by the traditional methods. Supported by theoretical modeling, we unveil a layer-by-layer CVD growth mode for constructing flattening surfaces, that is triggered by the high adhesion energy between gallium (Ga) and planar aromatic ligands. We further demonstrate the generality of the as-proposed OLGSS strategy by reproducing such a flat surface over nine different 2D c-MOF films with variable thicknesses (~2 to 208 nm) and large lateral sizes (over 1 cm2). The resultant ultra-smooth 2D c-MOF films enable the formation of high-quality electrical contacts with gold (Au) electrodes, leading to a reduction of contact resistance by over ten orders of magnitude compared to the traditional uneven MOF films. Furthermore, due to the efficient interfacial interaction benifited from the high-quality contacts, the prepared van der Waals heterostructure (vdWH) of OLGSS c-MOF and MoS2 exhibits intriguing photoluminescence (PL) enhancement, PL peak shift and large work function modulation. The establishment of the reliable OLGSS method provides the chances to push the development of MOF electronics and the construction of multicomponent MOF-based heterostructure materials.

physics.app-ph↗

arXiv2024

Interdot Lead Halide Excess Management in PbS Quantum Dot Solar Cells

Light-harvesting devices made from PbS quantum dot (QD) absorbers are one of the many promising technologies of third-generation photovoltaics. Their simple, solution-based fabrication together with a highly tunable and broad light absorption makes their application in newly developed solar cells particularly promising. In order to yield devices with reduced voltage and current losses, PbS QDs need to have strategically passivated surfaces, most commonly achieved through lead iodide and bromide passivation. The interdot spacing is then predominantly filled with residual amorphous lead halide species that remain from the ligand exchange, thus hindering efficient charge transport and reducing device stability. Herein, we demonstrate that a post-treatment by iodide based 2-phenylethlyammonium salts (X-PEAI) and intermediate 2D perovskite formation can be used to manage the lead halide excess in the PbS QD active layer. This treatment results in improved device performance and increased shelf-life stability, demonstrating the importance of interdot spacing management in PbS quantum dot photovoltaics.

physics.app-ph↗

arXiv2024

Dynamic Phase Enabled Topological Mode Steering in Composite Su-Schrieffer-Heeger Waveguide Arrays

Topological boundary states localize at interfaces whenever the interface implies a change of the associated topological invariant encoded in the geometric phase. The generically present dynamic phase, however, which is energy and time dependent, has been known to be non-universal, and hence not to intertwine with any topological geometric phase. Using the example of topological zero modes in composite Su-Schrieffer-Heeger (c-SSH) waveguide arrays with a central defect, we report on the selective excitation and transition of topological boundary mode based on dynamic phase-steered interferences. Our work thus provides a new knob for the control and manipulation of topological states in composite photonic devices, indicating promising applications where topological modes and their bandwidth can be jointly controlled by the dynamic phase, geometric phase, and wavelength in on-chip topological devices.

physics.optics↗

arXiv2024

SnS2 thin film with in-situ and controllable Sb doping via atomic layer deposition for optoelectronic applications

SnS2 stands out as a highly promising two-dimensional material with significant potential for applications in the field of electronics. Numerous attempts have been undertaken to modulate the physical properties of SnS2 by doping with various metal ions. Here, we deposited a series of Sb-doped SnS2 via atomic layer deposition (ALD) super-cycle process and compared its crystallinity, composition, and optical properties to those of pristine SnS2. We found that the increase in the concentration of Sb is accompanied by a gradual reduction in the Sn and S binding energies. The work function is increased upon Sb doping from 4.32 eV (SnS2) to 4.75 eV (Sb-doped SnS2 with 9:1 ratio). When integrated into photodetectors, the Sb-doped SnS2 showed improved performances, demonstrating increased peak photoresponsivity values from 19.5 A/W to 27.8 A/W at 405 nm, accompanied by an improvement in response speed. These results offer valuable insights into next-generation optoelectronic applications based on SnS2.

cond-mat.mtrl-sci↗

arXiv2023

Memlumor: a luminescent memory device for photonic neuromorphic computing

Neuromorphic computing promises to transform the current paradigm of traditional computing towards Non-Von Neumann dynamic energy-efficient problem solving. Thus, dynamic memory devices capable of simultaneously performing nonlinear operations (volatile) similar to neurons and also storing information (non-volatile) alike brain synapses are in the great demand. To satisfy these demands, a neuromorphic platform has to possess intrinsic complexity reflected in the built-in diversity of its physical operation mechanisms. Herein, we propose and demonstrate the novel concept of a memlumor - an all-optical device combining memory and luminophore, and being mathematically a full equivalence of the electrically-driven memristor. By utilizing metal halide perovskites as a memlumor material platform, we demonstrate the synergetic coexistence of both volatile and non-volatile memory effects within a broad timescale from ns to days. We elucidate the origin of such complex response to be related to the phenomena of photodoping and photochemistry activated by a tunable light input and explore several possible realizations of memlumor computing. Leveraging on the existence of a history-dependent photoluminescent quantum yield in various material platforms, the memlumor device concept will trigger multiple new research directions in both material science and optoelectronics. We anticipate that the memlumor, as a new optical dynamic computing element, will add a new dimension to existing optical technologies enabling their transition into application in photonic neuromorphic computing.

physics.optics↗

arXiv2022

Traps and transport resistance: the next frontier for stable state-of-the-art non-fullerene acceptor solar cells

Stability is one of the most important challenges facing organic solar cells (OSC) on their path to commercialization. In the high-performance material system PM6:Y6 studied here, investigate degradation mechanisms of inverted photovoltaic devices. We have identified two distinct degradation pathways: one requires presence of both illumination and oxygen and features a short-circuit current reduction, the other one is induced thermally and marked by severe losses of open-circuit voltage and fill factor. We focus our investigation on the thermally accelerated degradation. Our findings show that bulk material properties and interfaces remain remarkably stable, however, aging-induced defect state formation in the active layer remains the primary cause of thermal degradation. The increased trap density leads to higher non-radiative recombination, which limits open-circuit voltage and lowers charge carrier mobility in the photoactive layer. Furthermore, we find the trap-induced transport resistance to be the major reason for the drop in fill factor. Our results suggest that device lifetimes could be significantly increased by marginally suppressing trap formation, leading to a bright future for OSC.

cond-mat.mtrl-sci↗