arXiv subjects

Yannick Favre

Publications and source records attributed to Yannick Favre.

At least 19 recordsLinked to original sources

arXiv2026

Electromagnetic Shower Reconstruction and Identification in FASER's Emulsion Detector for LHC Forward Neutrino Measurements

We present methods for electromagnetic shower reconstruction and identification in the FASERnu emulsion detector using 100 GeV and 200 GeV electron test-beam data from the CERN SPS H4 beamline. The reconstruction employs a clustering-based algorithm without energy-dependent tuning to determine shower axes. A multi-level identification chain comprising track pre-selection, a cut-based selection, and a BDT classifier achieves combined background rejection rates of 99.99% (100 GeV) and 99.94% (200 GeV). The method reaches total reconstruction and identification efficiencies of 58.9% (100 GeV) and 70.8% (200 GeV) evaluated from simulated samples. Energy reconstruction using the total number of reconstructed segments as the calorimetric estimator yields relative biases of +0.6% (100 GeV) and -0.8% (200 GeV), with resolutions of 25.4% and 22.6%, respectively. Systematic uncertainties on the energy reconstruction are dominated by variations in emulsion film detection efficiency, with totals of (+10.9%/-8.2%) at 100 GeV and (+10.3%/-6.9%) at 200 GeV. The methodology provides a validated framework for electron neutrino identification with the FASERnu detector at the LHC.

hep-ex↗

arXiv2026

Momentum Measurement of Charged Particles in FASER's Emulsion Detector at the LHC

We present a momentum measurement method based on multiple Coulomb scattering (MCS) in the FASER$\nu$ emulsion detector. The measurement of charged-particle momenta is essential for studying neutrino interactions in the TeV energy range at the FASER experiment. This method exploits the sub-micron spatial resolution and long tracking length of the FASER$\nu$ detector, enabling momentum determination from a few GeV up to a few TeV. The performance was evaluated using Geant4-based Monte Carlo simulations and validated with muon test beam data in the momentum range 100-300 GeV. As a first probe of the method for higher momentum muons, background muons recorded by the FASER$\nu$ detector were examined, showing reconstructed momenta consistent with expectations from their angular spread.

hep-ex↗

arXiv2025

POLAR-2 -- Latest Developments of the Next Generation GRB Polarimeter

Gamma-Ray Bursts (GRBs) are among the most energetic events in the Universe. Despite over 50 years of research and measurements their prompt emission remains poorly understood, with key questions surrounding the structure of relativistic jets, magnetic field configurations, and dominant radiation mechanisms. Polarization measurements are critical in resolving these uncertainties. The POLAR mission, operational in 2016-2017 on Tiangong-2, provided the most statistically significant GRB polarization data. Its results indicated low time-averaged polarization with hints of temporal evolution. However, POLAR's limited sensitivity, small effective area, and restricted energy range prevented more detailed time- and energy-resolved analyses in addition to a larger sample of GRB polarization measurements. POLAR-2 is designed to address these limitations by offering a fourfold increase in effective area (at least) and an extended energy range of 30-800 keV by utilizing Silicon Photomultipliers (SiPMs) and an updated module design, enabling the differentiation of competing GRB emission models. The instrument comprises of 100 polarimeter modules (each with 64 plastic scintillator bars), wherein the polarization angle is extracted through Compton Scattering of the gammas. The polarimeter module design was validated during an ESRF beam test campaign in 2023. The instrument was developed by a joint effort of Switzerland, China, Poland and Germany and is planned for launch in 2027. Currently, POLAR-2 is in its production phase with the first module targets being produced. We will provide an overview of the current status of the development.

astro-ph.IM↗

arXiv2025

Gamma-Ray Burst Polarimetry with the POLAR and POLAR-2 missions

Gamma-Ray Bursts are among the most powerful and violent events in the Universe. Despite over half a century of observations of these transient sources, many open questions remain about their nature and the physical emission mechanisms at play. Polarization measurements of the GRB prompt gamma-ray emission have long been theorized to be able to answer most of these questions. Early polarization measurements did not allow to draw clear conclusions because of limited significance. With the aim of better characterizing the polarization of these prompt emissions, a compact Gamma-Ray polarimeter called POLAR has been sent to space as part of the Tiangong-2 Chinese space lab for 6 months of operations starting September 2016. The instrument detected 55 GRBs as well as several pulsars. Time-integrated polarization analysis of the 14 brightest detected GRBs has shown that the prompt emission is lowly polarized or fully unpolarized. However, time-resolved analysis depicted strong hints of an evolving polarization angle within single pulses, washing out the polarization degree in time-integrated analyses. Energy-resolved polarization analysis has shown no constraining results due to limited statistics. Hence, a more sensitive $\gamma$-ray polarimeter is required to perform detailed energy and time-resolved polarization analysis of the prompt gamma-ray emission of GRBs. Based on the success of the POLAR mission, a larger-scale instrument, approved for launch to the China Space Station (CSS) in 2027, is currently being developed by a Swiss, Chinese, Polish, and German collaboration. Thanks to its large sensitivity in the 20-800~keV range, POLAR-2 will produce polarization measurements of at least 50 GRBs per year with a precision equal to or higher than the best results published by POLAR, allowing for good quality time and energy resolved analysis.

astro-ph.HE↗

arXiv2025

Latest neutrino results from the FASER experiment and their implications for forward hadron production

The muon puzzle -- an excess of muons relative to simulation predictions in ultra-high-energy cosmic-ray air showers -- has been reported by many experiments. This suggests that forward particle production in hadronic interactions is not fully understood. Some of the scenarios proposed to resolve this predict reduced production of forward neutral pions and enhanced production of forward kaons (or other particles). The FASER experiment at the LHC is located 480 m downstream of the ATLAS interaction point and is sensitive to neutrinos and muons, which are the decay products of forward charged pions and kaons. In this study, the latest measurements of electron and muon neutrino fluxes are presented using the data corresponding to 9.5 $\mathrm{fb^{-1}}$ and 65.6 $\mathrm{fb^{-1}}$ of proton-proton collisions with $\sqrt{s}=13.6~\mathrm{TeV}$ by the FASER$\nu$ and the FASER electronic detector, respectively. These fluxes are compared with predictions from recent hadronic interaction models, including EPOS-LHCr, SIBYLL 2.3e, and QGSJET 3. The predictions are generally consistent with the measured fluxes from FASER, although some discrepancies appear in certain energy bins. More precise flux measurements with additional data will follow soon, enabling validation of pion, kaon, and charm meson production with finer energy binning, reduced uncertainties, and multi-differential analyses.

hep-ex↗

arXiv2025

Reconstruction and Performance Evaluation of FASER's Emulsion Detector at the LHC

This paper presents the reconstruction and performance evaluation of the FASER$\nu$ emulsion detector, which aims to measure interactions from neutrinos produced in the forward direction of proton-proton collisions at the CERN Large Hadron Collider. The detector, composed of tungsten plates interleaved with emulsion films, records charged particles with sub-micron precision. A key challenge arises from the extremely high track density environment, reaching $\mathcal{O}(10^5)$ tracks per cm$^2$. To address this, dedicated alignment techniques and track reconstruction algorithms have been developed, building on techniques from previous experiments and introducing further optimizations. The performance of the detector is studied by evaluating the single-film efficiency, position and angular resolution, and the impact parameter distribution of reconstructed vertices. The results demonstrate that an alignment precision of 0.3 micrometers and robust track and vertex reconstruction are achieved, enabling accurate neutrino measurements in the TeV energy range.

physics.ins-det↗

arXiv2025

Prospects and Opportunities with an upgraded FASER Neutrino Detector during the HL-LHC era: Input to the EPPSU

The FASER experiment at CERN has opened a new window in collider neutrino physics by detecting TeV-energy neutrinos produced in the forward direction at the LHC. Building on this success, this document outlines the scientific case and design considerations for an upgraded FASER neutrino detector to operate during LHC Run 4 and beyond. The proposed detector will significantly enhance the neutrino physics program by increasing event statistics, improving flavor identification, and enabling precision measurements of neutrino interactions at the highest man-made energies. Key objectives include measuring neutrino cross sections, probing proton structure and forward QCD dynamics, testing lepton flavor universality, and searching for beyond-the-Standard Model physics. Several detector configurations are under study, including high-granularity scintillator-based tracking calorimeters, high-precision silicon tracking layers, and advanced emulsion-based detectors for exclusive event reconstruction. These upgrades will maximize the physics potential of the HL-LHC, contribute to astroparticle physics and QCD studies, and serve as a stepping stone toward future neutrino programs at the Forward Physics Facility.

hep-ex↗

arXiv2025

Design and Performance of a Universal SiPM Readout System for X- and Gamma-Ray Missions

The advent of both multi-messenger and time-domain astrophysics over the last decade has seen a large interest in the development of small-scale, cheap, and robust gamma-ray detectors. This has been further encouraged by the availability of CubeSat platforms. Of particular interest are detectors capable of producing spectral and localization measurements of X and gamma-ray transients to allow for accurate follow-up measurements at different wavelengths. A vast number of the instruments developed for such purposes in the last years use a combination of scintillators and Silicon Photomultipliers (SiPMs) for photon detection. Here, we present the design, performance, and space qualification of a readout system capable of reading out 64 SiPM channels. This low-power and low-cost system was originally designed for the POLAR-2 mission, a large scale gamma-ray polarimeter. However, its flexible design makes it equally suitable for use on various CubeSat missions. The system was found to perform well when reading out both plastic and high Z scintillators using a total of 1.8~W. The space qualified design furthermore relies on commercial off-the-shelf components, thereby also removing most international export issues. In this paper, we will present the overall design, the performance of the electronics, its performance when reading out various scintillators and the successful space-qualification of this design.

astro-ph.IM↗

arXiv2024

First Measurement of the Muon Neutrino Interaction Cross Section and Flux as a Function of Energy at the LHC with FASER

This letter presents the measurement of the energy-dependent neutrino-nucleon cross section in tungsten and the differential flux of muon neutrinos and anti-neutrinos. The analysis is performed using proton-proton collision data at a center-of-mass energy of $13.6 \, {\rm TeV}$ and corresponding to an integrated luminosity of $(65.6 \pm 1.4) \, \mathrm{fb^{-1}}$. Using the active electronic components of the FASER detector, $338.1 \pm 21.0$ charged current muon neutrino interaction events are identified, with backgrounds from other processes subtracted. We unfold the neutrino events into a fiducial volume corresponding to the sensitive regions of the FASER detector and interpret the results in two ways: We use the expected neutrino flux to measure the cross section, and we use the predicted cross section to measure the neutrino flux. Both results are presented in six bins of neutrino energy, achieving the first differential measurement in the TeV range. The observed distributions align with Standard Model predictions. Using this differential data, we extract the contributions of neutrinos from pion and kaon decays.

hep-ex↗

arXiv2024

FANSIC: a Fast ANalog SiPM Integrated Circuit for the readout of large silicon photomultipliers

Silicon photo-multipliers (SiPM) have been replacing traditional photomultiplier tubes in most light sensing applications. However, when large detection surface coverage is needed, photomultipliers (PMTs) are still the preferred choice. The main reasons are the sensor thermal noise and the duration of the fast component of its signal, both increasing with the sensor surface. In this work we propose an application specific integrated circuit (ASIC), called Fast ANalog SiPM Integrated Circuit (FANSIC), for the readout of large SiPMs addressing these limitations. The ASIC has an active summation stage, which allows to divide a large detection surface into smaller ones offering faster response both in single ended and differential outputs. The high input bandwidth allows to reach full-width-half-maximum (FWHM) signals or the order of 3--5 ns which limits the impact of internal and external uncorrelated noise. The results of the first implementation of FANSIC, designed in CMOS 65 nm technology, is described in this paper.

physics.ins-det↗

arXiv2024

Performance tests and hardware qualification of the FEBs for the Super-FGD of T2K Phase II

T2K is a long baseline neutrino experiment, entering Phase II with a Near Detector upgrade. The T2K near detector (ND280) upgrade consists of the installation of three new detector systems: a plastic scintillator neutrino active target (Super-FGD), two time projection chambers (HA-TPC) and a time of flight detector (TOF). The Super-FGD is composed of 2-million 1 cm-cube scintillating cubes read by almost 60 thousand wavelength-shifting (WLS) fibers coupled to an MPPC on one end. Given the large number of channels, the limited space inside magnetic environment, and the limited time from production to installation, the development and testing of the Front-end electronics boards (FEB) for the read-out of the Super-FGD channels represented a challenging task for the success of the upgrade. This work presents the performance tests confirming that the FEB aligns with detector requirements, and the hardware qualification of 240 FEBs through a custom QC test bench designed to detect and locate hardware failures to speed up the repairing process. Installation of the electronics in the detector took place in March 2024, one year after the beginning of the FEB mass production, and the first successful neutrino beam run took place in June of the same year.

physics.ins-det↗

arXiv2024

Shining Light on the Dark Sector: Search for Axion-like Particles and Other New Physics in Photonic Final States with FASER

The first FASER search for a light, long-lived particle decaying into a pair of photons is reported. The search uses LHC proton-proton collision data at $\sqrt{s}=13.6~\text{TeV}$ collected in 2022 and 2023, corresponding to an integrated luminosity of $57.7\text{fb}^{-1}$. A model with axion-like particles (ALPs) dominantly coupled to weak gauge bosons is the primary target. Signal events are characterised by high-energy deposits in the electromagnetic calorimeter and no signal in the veto scintillators. One event is observed, compared to a background expectation of $0.44 \pm 0.39$ events, which is entirely dominated by neutrino interactions. World-leading constraints on ALPs are obtained for masses up to $300~\text{MeV}$ and couplings to the Standard Model W gauge boson, $g_{aWW}$, around $10^{-4}$ GeV$^{-1}$, testing a previously unexplored region of parameter space. Other new particle models that lead to the same experimental signature, including ALPs coupled to gluons or photons, U(1)$_B$ gauge bosons, up-philic scalars, and a Type-I two-Higgs doublet model, are also considered for interpretation, and new constraints on previously viable parameter space are presented in this paper.

hep-ex↗

arXiv2024

STROBE-X High Energy Modular Array (HEMA)

The High Energy Modular Array (HEMA) is one of three instruments that compose the STROBE-X mission concept. The HEMA is a large-area, high-throughput non-imaging pointed instrument based on the Large Area Detector developed as part of the LOFT mission concept. It is designed for spectral timing measurements of a broad range of sources and provides a transformative increase in sensitivity to X-rays in the energy range of 2--30 keV compared to previous instruments, with an effective area of 3.4 m$^{2}$ at 8.5 keV and an energy resolution of better than 300 eV at 6 keV in its nominal field of regard.

astro-ph.IM↗

arXiv2024

First Measurement of the $\nu_e$ and $\nu_\mu$ Interaction Cross Sections at the LHC with FASER's Emulsion Detector

This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$\nu$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$\nu$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated luminosity of 9.5 fb$^{-1}$. Applying stringent selections requiring electrons with reconstructed energy above 200~GeV, four electron neutrino interaction candidate events are observed with an expected background of $0.025^{+0.015}_{-0.010}$, leading to a statistical significance of 5.2$\sigma$. This is the first direct observation of electron neutrino interactions at a particle collider. Eight muon neutrino interaction candidate events are also detected, with an expected background of $0.22^{+0.09}_{-0.07}$, leading to a statistical significance of 5.7$\sigma$. The signal events include neutrinos with energies in the TeV range, the highest-energy electron and muon neutrinos ever detected from an artificial source. The energy-independent part of the interaction cross section per nucleon is measured over an energy range of 560--1740 GeV (520--1760 GeV) for $\nu_e$ ($\nu_{\mu}$) to be $(1.2_{-0.7}^{+0.8}) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$ ($(0.5\pm0.2) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$), consistent with Standard Model predictions. These are the first measurements of neutrino interaction cross sections in those energy ranges.

hep-ex↗

arXiv2024

Neutrino Rate Predictions for FASER

The Forward Search Experiment (FASER) at CERN's Large Hadron Collider (LHC) has recently directly detected the first collider neutrinos. Neutrinos play an important role in all FASER analyses, either as signal or background, and it is therefore essential to understand the neutrino event rates. In this study, we update previous simulations and present prescriptions for theoretical predictions of neutrino fluxes and cross sections, together with their associated uncertainties. With these results, we discuss the potential for possible measurements that could be carried out in the coming years with the FASER neutrino data to be collected in LHC Run 3 and Run 4.

hep-ex↗

arXiv2023

First Direct Observation of Collider Neutrinos with FASER at the LHC

We report the first direct observation of neutrino interactions at a particle collider experiment. Neutrino candidate events are identified in a 13.6 TeV center-of-mass energy $pp$ collision data set of 35.4 fb${}^{-1}$ using the active electronic components of the FASER detector at the Large Hadron Collider. The candidates are required to have a track propagating through the entire length of the FASER detector and be consistent with a muon neutrino charged-current interaction. We infer $153^{+12}_{-13}$ neutrino interactions with a significance of 16 standard deviations above the background-only hypothesis. These events are consistent with the characteristics expected from neutrino interactions in terms of secondary particle production and spatial distribution, and they imply the observation of both neutrinos and anti-neutrinos with an incident neutrino energy of significantly above 200 GeV.

hep-ex↗

arXiv2022

The FASER Detector

FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned with the beam collisions axis. FASER also includes a sub-detector, FASER$\nu$, designed to detect neutrinos produced in the LHC collisions and to study their properties. In this paper, each component of the FASER detector is described in detail, as well as the installation of the experiment system and its commissioning using cosmic-rays collected in September 2021 and during the LHC pilot beam test carried out in October 2021. FASER will start taking LHC collision data in 2022, and will run throughout LHC Run 3.

physics.ins-det↗

arXiv2022

The tracking detector of the FASER experiment

FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constructed from silicon microstrip detectors. Three of the tracker stations form a tracking spectrometer, and enable FASER to detect the decay products of LLPs decaying inside the apparatus, whereas the fourth station is used for the neutrino analysis. The spectrometer has been installed in the LHC complex since March 2021, while the fourth station is not yet installed. FASER will start physics data taking when the LHC resumes operation in early 2022. This paper describes the design, construction and testing of the tracking spectrometer, including the associated components such as the mechanics, readout electronics, power supplies and cooling system.

physics.ins-det↗