arXiv subjects

Alessandro Turchi

Publications and source records attributed to Alessandro Turchi.

14 recordsLinked to original sources

arXiv2026

In orbit background for hard X-ray CubeSat polarimeters: case study of the CUSP mission in low-earth orbit

The CUbesat Solar Polarimeter (CUSP) project aims to measure the linear polarization of solar flares in the 25 - 100 keV hard X-ray band using a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, initiated in December 2024 and closed on July 2nd, 2026, estimating the in orbit background to optimize the signal-to-background ratio was one of the key objectives. In low-Earth orbit, the instrument is exposed to cosmic and albedo X-ray backgrounds, charged particles, and secondary radiation from the spacecraft and atmosphere. Simulating these contributions enables optimization of detector geometry and shielding to maximize signal-to-noise performance. We present initial in orbit background estimates for CUSP using a Geant4-based simulator. A detailed mass model of the CUSP has been implemented to simulate background components and estimate the background count rate in the CUSP orbit.

astro-ph.IM↗

arXiv2026

The CUSP CubeSat mission for space weather multi-physics analysis, design, and testing

The CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. We present the outcomes of the CUSP's Phase B study, which is ended on 2 July 2026. The design solutions adopted for the mission's most critical multi-physics design drivers will be discussed, these solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. Moreover, we will discuss the validation of the Payload model based on the environmental testing campaign (e.g., vibration) carried out on a demonstrator.

astro-ph.IM↗

arXiv2026

Compton Polarimeter Prototype for the CUbesat Solar Polarimeter (CUSP) mission

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band (25-100 keV) by means of a dual-phase Compton polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project under development as part of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. In the frame of CUSP's Phase B, which started in December 2024, a flight-representative prototype of the Compton polarimeter has been developed and characterized with hard X-ray sources in the laboratory. This prototype consists of a 4$\times$4 central matrix of plastic scintillator bars surrounded by 4 strips of 8 elongated GAGG scintillators, respectively coupled to a multi-anode photomultiplier tube and arrays of avalanche photodiodes. These sensors are read out by custom front-end electronics based on MAROC-3A and SKIROC-2A ASICs with a Xilinx Artix 7 FPGA. The plastic scintillators act as scatterers, while the GAGG bars fully absorb the scattered photons. Coincident plastic-GAGG events allow for reconstructing the Compton scattering direction, whose distribution allows for inferring the polarization parameters of the source. We report here the measured performance of the polarimeter prototype using well-known radioactive isotopes and X-ray tubes, allowing us to assess the performance of our polarimeter prototype over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2026

Design and performance of the coded mask for the Lunar Electromagnetic Monitor in X-rays (LEM-X)

The Lunar Electromagnetic Monitor in X-rays (LEM-X) is a proposed wide-field X-ray observatory designed for deployment on the Moon's surface. Its primary scientific goal is to enhance multi-messenger astrophysics by detecting, localizing, and monitoring high-energy transient phenomena and variable X-ray sources across the sky. Building on the heritage of the eXTP and LOFT mission proposals, LEM-X employs pairs of coded-aperture cameras equipped with large-area linear Silicon Drift Detectors (SDDs), offering excellent spectral resolution ($\leq$350 eV at 6 keV) over the 2-50 keV energy range. Each camera provides a field of view of ~1 steradian at 25% effective area and achieves a Point-Source Location Accuracy (PSLA) of 1 arcminute, with an on-axis sensitivity better than 5 mCrab in 50 ks and 700 mCrab in 1 s. In this paper we describe the experiment and focus on the detailed design and optimization of the LEM-X coded mask, analyzing its scientific performance, imaging capabilities, and thermo-mechanical properties. We describe the mask code generation, decoding algorithms, and the trade-offs involved in achieving the required angular resolution, sensitivity, and structural integrity. Imaging simulations and mechanical analyses confirm the effectiveness of the proposed design, demonstrating its suitability for high-precision, wide-field X-ray imaging devoted to multi-messenger astrophysics and transient events detection.

astro-ph.IM↗

arXiv2026

Spectral performance of single-channel plastic and GAGG scintillator bars of the CUbesat Solar Polarimeter (CUSP)

Our Sun is the closest X-ray astrophysical source to Earth. As such, it makes a formidable case study to better understand astrophysical processes. Solar flares are in particular very interesting as they are linked to coronal mass ejections as well as magnetic field reconnection sites in the solar atmosphere. Flares can therefore provide insightful information on the physical processes at play on their production sites, but also on the emission and acceleration of energetic charged particles towards our planet, making it a formidable forecasting tool for space weather. While solar flares are critical to understanding magnetic reconnection and particle acceleration, their hard X-ray polarization -- key to distinguishing between competing theoretical models -- remains poorly constrained by existing observations. To address this, we present the CUbesat Solar Polarimeter (CUSP), a mission under development to perform solar flare polarimetry in the 25-100 keV energy range. CUSP consists of a 6U-XL platform hosting a dual-phase Compton polarimeter. The polarimeter is made of a central assembly of four 4x4 arrays of plastic scintillators, each coupled to multi-anode photomultiplier tubes, surrounded by four strips of eight elongated GAGG scintillator bars coupled to avalanche photodiodes. Both types of sensors from Hamamatsu are respectively read out by the MAROC-3A and SKIROC-2A ASICs from Weeroc. In this manuscript, we present the preliminary spectral performances of single plastic and GAGG channels measured in the laboratory using development boards of the ASICs foreseen for the flight model.

astro-ph.IM↗

arXiv2025

Solar Flare Hard X-ray Polarimetry with the CUbesat Solar Polarimeter (CUSP) mission

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission planned for a launch in low-Earth orbit and aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. It is undergoing a 12-month Phase B that started in December 2024. The Compton polarimeter on board CUSP is composed of two acquisition chains based on plastic scintillators read out by Multi-Anode PhotoMultiplier Tubes for the scatterer part and GAGG crystals coupled to Avalanche PhotoDiodes for the absorbers. An event coincident between the two readout schemes will lead to a measurement of the incoming X-ray's azimuthal scattering angle, linked to the polarization of the solar flare in a statistical manner. The current status of the CUSP mission design, mission analysis, and payload scientific performance will be reported. The latter will be discussed based on preliminary laboratory results obtained in parallel with Geant4 simulations.

astro-ph.SR↗

arXiv2025

The multi-physics analysis, design and testing of CUSP, a CubeSat mission for space weather and solar flares x-ray polarimetry

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. As part of CUSP's Phase B study, which began in December 2024 and will last one year, we present the current development status of the design solutions adopted for the mission's most critical multi-physics design drivers. These solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. In particular, we describe the mechanical design of each structural component, the results of static, dynamic finite element analyses, and a proposal for topological optimization of the interface between the platform and payload and some fixture for test, and the preliminary environmental testing campaign (e.g., vibration, shock) that will be carried out on a mechanical demonstrator.

astro-ph.IM↗

arXiv2025

The CUbesat Solar Polarimeter (CUSP): mission overview II

The CUbesat Solar Polarimeter (CUSP) project is an Earth-orbiting CubeSat mission designed to measure the linear polarization of solar flares in the hard X-ray band using a Compton scattering polarimeter. CUSP will enable the study of magnetic reconnection and particle acceleration within the Sun's flaring magnetic structures. This project is being developed within the framework of the Italian Space Agency's Alcor Program, which aims to foster new CubeSat missions. CUSP entered its Phase B in December 2024, a phase scheduled to last 12 months. This paper reports on the current status of the CUSP mission design, mission analysis, and payload scientific performance.

astro-ph.SR↗

arXiv2025

CUbesat Solar Polarimeter (CUSP) Sensitivity Estimation and Performance Optimization using Geant4

The CUbesat Solar Polarimeter (CUSP) aims to measure the linear polarization of solar flares in the 25-100 keV X-ray band using a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star by providing high-sensitivity polarization measurements. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, which began in December 2024 and will continue for one year, we present the development status of the Geant4 based simulator to accurately simulate the detectors response and initial results on the sensitivity of the instrument. Geant4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. We implemented a detailed CUSP Mass Model within Geant4 to simulate and estimate the instruments sensitivity, correcting the geometric effects of the instrument. We also evaluated the effect of backscattering shielding on the sensitivity to optimize the mass model of the instrument.

astro-ph.SR↗

arXiv2025

Prototype Development and Calibration of the CUbesat Solar Polarimeter (CUSP)

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It has been proposed as a constellation of a two Cubesat mission to monitor the Sun for Space Weather, and will proceed with a single-satellite asset in its baseline implementation. In the frame of CUSP's Phase B study, that started in December 2024 for a 1-year period, we present the development status of this dual-phase polarimeter. Preliminary laboratory results using two chains of acquisition will be discussed. The first chain of acquisition, based on the Hamamatsu R7600 multi-anode photomultiplier tubes coupled to plastic scintillator bars and read out by the MAROC-3A ASIC, is used to detect the Compton scattering of incoming photons. On the other hand, GAGG crystals coupled to avalanche photo-diodes with a readout based on the SKIROC-2A ASIC are used to absorb the scattered photons. By reconstructing the azimuthal scattering direction for many incoming photons, one can infer the linear polarization degree and angle of the source. We will discuss the calibration results obtained with our prototype detector by using well-known radioactive isotopes, allowing us to assess the performances of our detector over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2025

Study of the HV power supply modules for the CUbesat Solar Polarimeter (CUSP)

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. CUSP undergoing the Phase B started in December 2024 that will last for 12 month. The Compton polarimeter of the CUSP payload performs coincidence measurements between plastic scintilaltors and GaGG(Ce) crystals to derive the polarization of X-rays. These sensors are readout by Multi Anode Photomultiplier Tubes (MAPMTs) and Avalanche Photodiodes (APDs) respectively. Both sensors need an HV power supply up to -1~kV (for the MAPMT) and +500~V (for the APD). We tested precision regulated High Voltage DC/DC Converters by HVM Technology Inc. with Sub-Miniature Case Size ($0.85''\times0.85''\times0.60''$) of the SMHV series. These modules are compact and suited for CubeSat missions.

astro-ph.IM↗

arXiv2025

Characterization of the VKI Plasmatron subsonic ICP jet combining optical emission spectroscopy, intrusive measurements, and CFD simulations

This paper addresses the characterization of the subsonic flow in the 1.2~MW Inductively Coupled Plasma (ICP) wind tunnel at the von Karman Institute for Fluid Dynamics (VKI), targeting chamber pressures of 50 and 100~mbar, and input electric powers between 150 and 300~kW. Ultraviolet to near-infrared optical emission spectroscopy measurements of the free-jet flow are carried out with an updated experimental set-up, calibration procedure, and data processing, providing high-quality absolute spatially-resolved emission spectra. Emission measurements agree with thermochemical equilibrium predictions within a range of conditions, allowing to extract experimental maps of cold-wall heat flux and dynamic pressure against the inferred free-jet enthalpy. A detailed comparison with the characterization methodology traditionally employed is presented, highlighting the need for an improved modeling strategy. Using the measured free-jet temperature and dynamic pressure only, a forward procedure for the computation of the stagnation line flow is proposed. The latter agrees with intrusive heat flux measurements through a range of test conditions, and for values of the recombination coefficient of the reference copper probe commonly found in the literature. Results demonstrate that a consistent framework between numerical simulations and experimental data can be achieved, defining an improved framework for the characterization of the subsonic ICP jet.

physics.flu-dyn↗

arXiv2023

Assessment of Immersed Boundary Methods for Hypersonic Flows with Gas-Surface Interactions

Immersed boundary (IB) methods with adaptive mesh refinement (AMR) techniques are assessed for atmospheric entry applications, including effects of chemical nonequilibrium (CNE) and gas-surface interactions (GSI). The performance of a conservative cut-cell and two non-conservative ghost-cell IB methods is assessed in comparison with analytical solutions, data from literature, and results obtained with a reference solver that operates on body-fitted grids. All solvers use the same external thermochemistry library so that all observed differences can be attributed to the underlying numerical methods. Results from eight benchmark cases are reported. Four cases are selected to verify the implementation of chemistry, transport properties, catalytic boundary conditions, and shock capturing. Four validation cases consider blunt geometries with adiabatic/isothermal and inert/catalytic/ablative boundary conditions. Overall, the results obtained with the IB solvers are in very good agreement with the reference data. Discrepancies arise with ghost-cell methods for cases with large temperature or concentration gradients at the wall and are attributed to mass conservation errors. Only a strictly conservative cut-cell IB method is on par with body-fitted grid methods.

physics.flu-dyn↗

arXiv2022

Data-driven modeling of hypersonic reentry flow with heat and mass transfer

The entry phase constitutes a design driver for aerospace systems that include such a critical step. This phase is characterized by hypersonic flows encompassing multiscale phenomena that require advanced modeling capabilities. However, since high fidelity simulations are often computationally prohibitive, simplified models are needed in multidisciplinary analyses requiring fast predictions. This work proposes data-driven surrogate models to predict the flow, and mixture properties along the stagnation streamline of hypersonic flows past spherical objects. Surrogate models are designed to predict velocity, pressure, temperature, density and air composition as a function of the object's radius, velocity, reentry altitude and surface temperature. These models are trained with data produced by numerical simulation of the quasi-one-dimensional Navier-Stokes formulation and a selected Earth atmospheric model. Physics-constrained parametric functions are constructed for each flow variable of interest, and artificial neural networks are used to map the model parameters to the model's inputs. Surrogate models were also developed to predict surface quantities of interest for the case of nonreacting or ablative carbon-based surfaces, providing alternatives to semiempirical correlations. A validation study is presented for all the developed models, and their predictive capabilities are showcased along selected reentry trajectories of space debris from low-Earth orbits.

physics.flu-dyn↗