arXiv subjects

Herre S. J. van der Zant

Publications and source records attributed to Herre S. J. van der Zant.

At least 127 records · Page 7Linked to original sources

arXiv2015

High-Q Tantalum Oxide Nanomechanical Resonators by Laser-Oxidation of TaSe2

Controlling the strain in two-dimensional materials is an interesting avenue to tailor the mechanical properties of nanoelectromechanical systems. Here we demonstrate a technique to fabricate ultrathin tantalum oxide nanomechanical resonators with large stress by laser-oxidation of nano-drumhead resonators made out of tantalum diselenide (TaSe2), a layered 2D material belonging to the metal dichalcogenides. Prior to the study of their mechanical properties with a laser interferometer, we checked the oxidation and crystallinity of the freely-suspended tantalum oxide in a high-resolution electron microscope. We show that the stress of tantalum oxide resonators increase by 140 MPa (with respect to pristine TaSe2 resonators) which causes an enhancement of quality factor (14 times larger) and resonance frequency (9 times larger) of these resonators.

cond-mat.mes-hall↗

arXiv2015

TiS3 transistors with tailored morphology and electrical properties

Control over the morphology of TiS3 is demonstrated by synthesizing 1D nanoribbons and 2D nanosheets. The nanosheets can be exfoliated down to a single layer. Through extensive characterization of the two morphologies, differences in the electronic properties are found and attributed to a higher density of sulphur vacancies in nanosheets which, according to density functional theory calculations, leads to an n-type doping.

cond-mat.mtrl-sci↗

arXiv2015

Fabrication of hybrid molecular devices using multi-layer graphene break junctions

We report on the fabrication of hybrid molecular devices employing multilayer graphene (MLG) flakes which are patterned with a constriction using a helium ion microscope (HIM) or an oxygen plasma etch. The patterning step allows for the localization of a few-nanometer gap, created by electroburning, that can host single molecules or molecular ensembles. By controlling the width of the sculpted constriction, we regulate the critical power at which the electroburning process begins. We estimate the flake temperature given the critical power and find that at low powers it is possible to electroburn MLG with superconducting contacts in close proximity. Finally, we demonstrate the fabrication of hybrid devices with superconducting contacts and anthracene-functionalized copper curcuminoid molecules. This method is extendable to spintronic devices with ferromagnetic contacts and a first step towards molecular integrated circuits.

cond-mat.mes-hall↗

arXiv2015

Environmental instability of few-layer black phosphorus

We study the environmental instability of mechanically exfoliated few-layer black phosphorus (BP). From continuous measurements of flake topography over several days, we observe an increase of over 200% in volume due to the condensation of moisture from air. We find that long term exposure to ambient conditions results in a layer-by-layer etching process of BP flakes. Interestingly, flakes can be etched down to single layer (phosphorene) thicknesses. BP's strong affinity for water greatly modifies the performance of fabricated field-effect transistors (FETs) measured in ambient conditions. Upon exposure to air, we differentiate between two timescales for doping of BP FET transfer characterisitcs: a short timescale (minutes) in which a shift in the threshold voltage occurs due to physisorbed oxygen and nitrogen, and a long timescale (hours) in which p-type doping occurs from water absorption. Continuous measurements of BP FETs in air reveal eventual degradation and break-down of the channel material after several days due to the layer-by-layer etching process.

cond-mat.mtrl-sci↗

arXiv2015

Mechanics of freely-suspended ultrathin layered materials

The study of atomically thin two-dimensional materials is a young and rapidly growing field. In the past years, a great advance in the study of the remarkable electrical and optical properties of 2D materials fabricated by exfoliation of bulk layered materials has been achieved. Due to the extraordinary mechanical properties of these atomically thin materials, they also hold a great promise for future applications such as flexible electronics. For example, this family of materials can sustain very large deformations without breaking. Due to the combination of small dimensions, high Young's modulus and high crystallinity of 2D materials, they have attracted the attention of the field of nanomechanical systems as high frequency and high quality factor resonators. In this article, we review experiments on static and dynamic response of 2D materials. We provide an overview and comparison of the mechanics of different materials, and highlight the unique properties of these thin crystalline layers. We conclude with an outlook of the mechanics of 2D materials and future research directions such as the coupling of the mechanical deformation to their electronic structure.

cond-mat.mes-hall↗

arXiv2014

Spin switching in electronic devices based on 2D assemblies of spin-crossover nanoparticles

In this communication we study the transport properties of two-dimensional assemblies of [Fe(Htrz)2(trz)](BF4) spin-crossover nanoparticles (NPs) with two different morphologies. The NPs have been synthesized made in a similar manner than in our previous study in which single NPs were measured. We prepared free-standing self-assembled monolayer sheets of both SCO NPs formed at the air/liquid interface on holey carbon TEM grids to extract their global arrangement and NP size distributions by STEM-HAADF technique. The SCO NP systems present a rod-like shape and possess two different volumes, corresponding to lengths of 25 nm and 44 nm along the rod direction and average diameters of 10 nm and 6 nm respectively. In a similar manner, sheets of SCO NPs with the two different morphologies were electrically measured by contacting them on pre-patterned gold electrodes substrates. For both NP morphologies, a thermal hysteresis loop in the electrical conductance near room temperature was observed, which was correlated to their morphologies and 2D organization. The most remarkable result was the observation of an unprecedented large change in the electrical conductance of the two spin states, increasing by up to two orders of magnitude in the 2D assemblies of spin-crossover NPs. This value is significantly larger than that obtained in single-NP measurements (~ 3). Although such large conductance changes are not fully understood, our results point at important contributions from its size/morphology-dependence at the nanoscale.

cond-mat.mes-hall↗

arXiv2014

Electron-vibron coupling effects on electron transport via a single-molecule magnet

We investigate how the electron-vibron coupling influences electron transport via an anisotropic magnetic molecule, such as a single-molecule magnet (SMM) Fe$_4$, by using a model Hamiltonian with parameter values obtained from density-functional theory (DFT). Magnetic anisotropy parameters, vibrational energies, and electron-vibron coupling strengths of the Fe$_4$ are computed using DFT. A giant spin model is applied to the Fe$_4$ with only two charge states, specifically a neutral state with the total spin $S=5$ and a singly charged state with $S=9/2$, which is consistent with our DFT result and experiments on Fe$_4$ single-molecule transistors. In sequential electron tunneling, we find that the magnetic anisotropy gives rise to new features in conductance peaks arising from vibrational excitations. In particular, the peak height shows a strong, unusual dependence on the direction as well as magnitude of applied B field. The magnetic anisotropy also introduces vibrational satellite peaks whose position and height are modified with the direction and magnitude of applied B field. Furthermore, when multiple vibrational modes with considerable electron-vibron coupling have energies close to one another, a low-bias current is suppressed, independently of gate voltage and applied B field, although that is not the case for a single mode with the similar electron-vibron coupling. In the former case, the conductance peaks reveal a stronger B-field dependence than in the latter case. The new features appear because the magnetic anisotropy barrier is of the same order of magnitude as the energies of vibrational modes with significant electron-vibron coupling. Our findings clearly show the interesting interplay between magnetic anisotropy and electron-vibron coupling in electron transport via the Fe$_4$. The similar behavior can be observed in transport via other anisotropic magnetic molecules.

cond-mat.mes-hall↗

arXiv2014

Photovoltaic and photothermoelectric effect in a double-gated WSe2 device

Tungsten diselenide (WSe2), a semiconducting transition metal dichalcogenide (TMDC), shows great potential as active material in optoelectronic devices due to its ambipolarity and direct bandgap in its single-layer form. Recently, different groups have exploited the ambipolarity of WSe2 to realize electrically tunable PN junctions, demonstrating its potential for digital electronics and solar cell applications. In this Letter, we focus on the different photocurrent generation mechanisms in a double-gated WSe2 device by measuring the photocurrent (and photovoltage) as the local gate voltages are varied independently in combination with above- and below-bandgap illumination. This enables us to distinguish between two main photocurrent generation mechanisms: the photovoltaic and photothermoelectric effect. We find that the dominant mechanism depends on the defined gate configuration. In the PN and NP configurations, photocurrent is mainly generated by the photovoltaic effect and the device displays a maximum responsivity of 0.70 mA/W at 532 nm illumination and rise and fall times close to 10 ms. Photocurrent generated by the photothermoelectric effect emerges in the PP configuration and is a factor of two larger than the current generated by the photovoltaic effect (in PN and NP configurations). This demonstrates that the photothermoelectric effect can play a significant role in devices based on WSe2 where a region of strong optical absorption, caused by e.g. an asymmetry in flake thickness or optical absorption of the electrodes, generates a sizeable thermal gradient upon illumination.

cond-mat.mes-hall↗

arXiv2014

Photovoltaic effect in few-layer black phosphorus PN junctions defined by local electrostatic gating

The photovoltaic effect is one of the fundamental light-matter interactions in light energy harvesting. In conventional photovoltaic solar cells, the photogenerated charge carriers are extracted by the built-in electric field of a PN junction, typically defined by ionic dopants in a semiconductor. In atomically thin semiconductors, the doping level can be controlled by the field-effect without need of implanting dopants in the lattice, which makes 2D semiconductors prospective materials to implement electrically tunable PN junctions. However, most 2D semiconducting materials do not show ambipolar P-type and N-type field-effect transport, necessary to realize PN junctions. Few-layer black phosphorus is a recently isolated 2D semiconductor that presents a direct bandgap, high mobility, current on/off ratio and ambipolar operation. Here, we fabricate few-layer black phosphorus (b-P) field-effect transistors with split bottom gates and crystalline hexagonal boron nitride (h-BN) dielectric. We demonstrate electrostatic control of the local charge carrier type and density above each gate in the device, tuning its electrical behaviour from metallic to rectifying. Illuminating a gate-defined PN junction, we observe zero-bias photocurrents and significant open-circuit voltage, which we attribute to the separation of electron-hole pairs driven by the internal electric field at the junction region. Due to the small bandgap of the material, we observe photocurrents and photovoltages for illumination wavelengths up to 940 nm, attractive for energy harvesting applications in the near-infrared region

cond-mat.mes-hall↗

arXiv2014

Isolation and characterization of few-layer black phosphorus

Isolation and characterization of mechanically exfoliated black phosphorus flakes with a thickness down to two single-layers is presented. A modification of the mechanical exfoliation method, which provides higher yield of atomically thin flakes than conventional mechanical exfoliation, has been developed. We present general guidelines to determine the number of layers using optical microscopy, Raman spectroscopy and transmission electron microscopy in a fast and reliable way. Moreover, we demonstrate that the exfoliated flakes are highly crystalline and that they are stable even in free-standing form through Raman spectroscopy and transmission electron microscopy measurements. A strong thickness dependence of the band structure is found by density functional theory calculations. The exciton binding energy, within an effective mass approximation, is also calculated for different number of layers. Our computational results for the optical gap are consistent with preliminary photoluminescence results on thin flakes. Finally, we study the environmental stability of black phosphorus flakes finding that the flakes are very hydrophilic and that long term exposure to air moisture etches black phosphorus away. Nonetheless, we demonstrate that the aging of the flakes is slow enough to allow fabrication of field-effect transistors with strong ambipolar behavior. Density functional theory calculations also give us insight into the water-induced changes of the structural and electronic properties of black phosphorus.

cond-mat.mes-hall↗

arXiv2014

Ultrahigh photoresponse of few-layer TiS3 nanoribbon transistors

Here, we isolate thin TiS3 ribbons, a layered direct band gap semiconductor (1.1 eV, well suited for detection all across the visible spectrum), thus far almost unexplored. We fabricate field effect transistors and study their electrical characteristics and optoelectronic properties. The measured FET characteristics show mobilities up to 2.6 cm^2/Vs and ON/OFF ratios up to 10^4. Under illumination, the TiS3 NR-FETs present an ultrahigh photoresponse of 2910 A/W and fast rise/fall times of ~4 ms. In addition, we measure cutoff frequencies (f3dB) up to 1000 Hz. The strong combination of ultrahigh sensitivity all along the visible spectrum and fast time response of TiS3 nanoribbon transistors put them among the best nanoscale photodetectors to date.

cond-mat.mes-hall↗

arXiv2014

Fast and broadband photoresponse of few-layer black phosphorus field-effect transistors

Few-layer black phosphorus, a new elemental 2D material recently isolated by mechanical exfoliation, is a high-mobility layered semiconductor with a direct bandgap that is predicted to strongly depend on the number of layers, from 0.35 eV (bulk) to 2.0 eV (single-layer). Therefore, black phosphorus is an appealing candidate for tunable photodetection from the visible to the infrared part of the spectrum. We study the photoresponse of field-effect transistors (FETs) made of few-layer black phosphorus (3 nm to 8 nm thick), as a function of excitation wavelength, power and frequency. In the dark state, the black phosphorus FETs can be tuned both in hole and electron doping regimes allowing for ambipolar operation. We measure mobilities in the order of 100 cm2/V s and current ON/OFF ratio larger than 103. Upon illumination, the black phosphorus transistors show response to excitation wavelengths from the visible up to 940 nm and rise time of about 1 ms, demonstrating broadband and fast detection. The responsivity reaches 4.8 mA/W and it could be drastically enhanced by engineering a detector based on a PN junction. The ambipolar behavior coupled to the fast and broadband photodetection make few-layer black phosphorus a promising 2D material for photodetection across the visible and near-infrared part of the electromagnetic spectrum.

cond-mat.mes-hall↗

arXiv2014

Deterministic transfer of two-dimensional materials by all-dry viscoelastic stamping

Deterministic transfer of two-dimensional crystals constitutes a crucial step towards the fabrication of heterostructures based on artificial stacking of two-dimensional materials. Moreover, control on the positioning of two-dimensional crystals facilitates their integration in complex devices, which enables the exploration of novel applications and the discovery of new phenomena in these materials. Up to date, deterministic transfer methods rely on the use of sacrificial polymer layers and wet chemistry to some extent. Here, we develop an all-dry transfer method that relies on viscoelastic stamps and does not employ any wet chemistry step. This is found very advantageous to freely suspend these materials as there are no capillary forces involved in the process. Moreover, the whole fabrication process is quick, efficient, clean, and it can be performed with high yield.

cond-mat.mes-hall↗

arXiv2014

Single-layer MoS2 mechanical resonators

Here, we demonstrate the fabrication of single-layer MoS2 mechanical resonators. The fabricated resonators have fundamental resonance frequencies in the order of 10 MHz to 30 MHz (depending on their geometry) and their quality factor is about ~55 at room temperature in vacuum. The dynamical properties clearly indicate that monolayer MoS2 membranes are in the membrane limit (i.e., tension dominated), in contrast to their thicker counterparts, which behave as plates. We also demonstrate clear signatures of nonlinear behaviour of our atomically thin membranes, thus providing a starting point for future investigations on the nonlinear dynamics of monolayer nanomechanical resonators.

cond-mat.mes-hall↗

arXiv2014

Fast and reliable identification of atomically thin layers of TaSe2 crystals

Deposition of clean and defect-free atomically thin two-dimensional crystalline flakes on surfaces by mechanical exfoliation of layered bulk materials has proven to be a powerful technique, but it requires a fast, reliable and non-destructive way to identify the atomically thin flakes among a crowd of thick flakes. In this work, we provide general guidelines to identify ultrathin flakes of TaSe2 by means of optical microscopy and Raman spectroscopy. Additionally, we determine the optimal substrates to facilitate the optical identification of atomically thin TaSe2 crystals. Experimental realization and isolation of ultrathin layers of TaSe2 enables future studies on the role of the dimensionality in interesting phenomena such as superconductivity and charge density waves.

cond-mat.mes-hall↗

arXiv2013

Local strain engineering in atomically thin MoS2

Tuning the electronic properties of a material by subjecting it to strain constitutes an important strategy to enhance the performance of semiconducting electronic devices. Using local strain, confinement potentials for excitons can be engineered, with exciting possibilities for trapping excitons for quantum optics and for efficient collection of solar energy. Two-dimensional materials are able to withstand large strains before rupture, offering a unique opportunity to introduce large local strains. Here, we study atomically thin MoS2 layers with large local strains of up to 2.5% induced by controlled delamination from a substrate. Using simultaneous scanning Raman and photoluminescence imaging, we spatially resolve a direct bandgap reduction of up to 90 meV induced by local strain. We observe a funnel effect in which excitons drift hundreds of nanometers to lower bandgap regions before recombining, demonstrating exciton confinement by local strain. The observations are supported by an atomistic tight-binding model developed to predict the effect of inhomogeneous strain on the local electronic states in MoS2. The possibility of generating large strain-induced variations in exciton trapping potentials opens the door for a variety of applications in atomically thin materials including photovoltaics, quantum optics and two-dimensional optoelectronic devices.

cond-mat.mes-hall↗

arXiv2013

The effect of the substrate on the Raman and photoluminescence emission of single layer MoS2

We quantitatively study the Raman and photoluminescence (PL) emission from single layer molybdenum disulfide (MoS2) on dielectric (SiO2, hexagonal boron nitride, mica and the polymeric dielectric Gel-Film) and conducting substrates (Au and few-layer graphene). We find that the substrate can affect the Raman and PL emission in a twofold manner. First, the absorption and emission intensities are strongly modulated by the constructive/destructive interference within the different substrates. Second, the position of the A1g Raman mode peak and the spectral weight between neutral and charged excitons in the PL spectra are modified by the substrate. We attribute this effect to substrate-induced changes in the doping level and in the decay rates of the excitonic transitions. Our results provide a method to quantitatively study the Raman and PL emission from MoS2-based vertical heterostructures and represent the first step in ad-hoc tuning the PL emission of 1L MoS2 by selecting the proper substrate.

cond-mat.mtrl-sci↗

arXiv2013

Long-range Scanning Tunneling Microscope for the study of nanostructures on insulating substrates

The Scanning Tunneling Microscope is a powerful tool for studying the electronic properties at the atomic level, however it's relatively small scanning range and the fact that it can only operate on conducting samples prevents its application to study heterogeneous samples consisting on conducting and insulating regions. Here we present a long-range scanning tunneling microscope capable of detecting conducting micro and nanostructures on insulating substrates using a technique based on the capacitance between the tip and the sample and performing STM studies.

cond-mat.mes-hall↗