arXiv subjects

Karl K. Berggren

Publications and source records attributed to Karl K. Berggren.

At least 37 records · Page 2Linked to original sources

arXiv2024

Lightwave-Electronic Harmonic Frequency Mixing

Electronic frequency mixers are fundamental building blocks of electronic systems. Harmonic frequency mixing in particular enables broadband electromagnetic signal analysis across octaves of spectrum using a single local oscillator. However, conventional harmonic frequency mixers do not operate beyond hundreds of GHz to a few THz. If extended to the petahertz scale in a compact and scalable form, harmonic mixers would enable field-resolved optical signal analysis spanning octaves of spectra in a monolithic device without the need for frequency conversion using nonlinear crystals. Here we demonstrate lightwave-electronic harmonic frequency mixing beyond 0.350 PHz using plasmonic nanoantennas. We demonstrate that the mixing process enables complete, field-resolved detection of spectral content far outside that of the local oscillator, greatly extending the range of detectable frequencies compared to conventional heterodyning techniques. Our work has important implications for applications where optical signals of interest exhibit coherent femtosecond-scale dynamics spanning multiple harmonics.

physics.optics↗

arXiv2024

Nanocryotron ripple counter integrated with a superconducting nanowire single-photon detector for megapixel arrays

Decreasing the number of cables that bring heat into the cryostat is a critical issue for all cryoelectronic devices. Especially, arrays of superconducting nanowire single-photon detectors (SNSPDs) could require more than $10^6$ readout lines. Performing signal processing operations at low temperatures could be a solution. Nanocryotrons, superconducting nanowire three-terminal devices, are good candidates for integrating sensing and electronics on the same technological platform as SNSPDs in photon-counting applications. In this work, we demonstrated that it is possible to read out, process, encode, and store the output of SNSPDs using exclusively superconducting nanowires. In particular, we present the design and development of a nanocryotron ripple counter that detects input voltage spikes and converts the number of pulses to an $N$-digit value. The counting base can be tuned from 2 to higher values, enabling higher maximum counts without enlarging the circuit. As a proof-of-principle, we first experimentally demonstrated the building block of the counter, an integer-$N$ frequency divider with $N$ ranging from 2 to 5. Then, we demonstrated photon-counting operations at 405 nm and 1550 nm by coupling an SNSPD with a 2-digit nanocryotron counter partially integrated on-chip. The 2-digit counter could operate in either base 2 or base 3 with a bit error rate lower than $2 \times 10^{-4}$ and a count rate of $10^7\,$s$^{-1}$. We simulated circuit architectures for integrated readout of the counter state, and we evaluated the capabilities of reading out an SNSPD megapixel array that would collect up to $10^{12}$ counts per second. The results of this work, combined with our recent publications on a nanocryotron shift register and logic gates, pave the way for the development of nanocryotron processors, from which multiple superconducting platforms may benefit.

physics.app-ph↗

arXiv2024

Analysis and Applications of a Heralded Electron Source

We analytically describe the noise properties of a heralded electron source made from a standard electron gun, a weak photonic coupler, a single photon counter, and an electron energy filter. We argue the traditional heralding figure of merit, the Klyshko efficiency, is an insufficient statistic for characterizing performance in dose-control and dose-limited applications. Instead, we describe the sub-Poissonian statistics of the source using the fractional reduction in variance and the fractional increase in Fisher Information. Using these figures of merit, we discuss the engineering requirements for efficient heralding and evaluate potential applications using simple models of electron lithography, bright-field scanning transmission electron microscopy (BFSTEM), and scanning electron microscopy (SEM). We find that the advantage in each of these applications is situational, but potentially significant: dynamic control of the trade-off between write speed and shot noise in electron lithography; an order of magnitude dose reduction in BFSTEM for thin samples (e.g. 2D materials); and a doubling of dose efficiency for wall-steepness estimation in SEM.

physics.app-ph↗

arXiv2024

Improvements of readout signal integrity in mid-infrared superconducting nanowire single photon detectors

Superconducting nanowire single-photon detectors (SNSPDs) with high timing resolution and low background counts in the mid infrared (MIR) have the potential to open up numerous opportunities in fields such as exoplanet searches, direct dark matter detection, physical chemistry, and remote sensing. One challenge in pushing SNSPD sensitivity to the MIR is a decrease in the signal-to-noise ratio (SNR) of the readout signal as the critical currents become increasingly smaller. We overcome this trade-off with a new device architecture that employs impedance matching tapers and superconducting nanowire avalanche photodetectors to demonstrate increased SNR while maintaining saturated internal detection efficiency at 7.4 μm and getting close to saturation at 10.6 μm. This work provides a novel platform for pushing SNSPD sensitivity to longer wavelengths while improving the scalability of the readout electronics.

physics.ins-det↗

arXiv2023

Quantum Sensors for High Energy Physics

Strong motivation for investing in quantum sensing arises from the need to investigate phenomena that are very weakly coupled to the matter and fields well described by the Standard Model. These can be related to the problems of dark matter, dark sectors not necessarily related to dark matter (for example sterile neutrinos), dark energy and gravity, fundamental constants, and problems with the Standard Model itself including the Strong CP problem in QCD. Resulting experimental needs typically involve the measurement of very low energy impulses or low power periodic signals that are normally buried under large backgrounds. This report documents the findings of the 2023 Quantum Sensors for High Energy Physics workshop which identified enabling quantum information science technologies that could be utilized in future particle physics experiments, targeting high energy physics science goals.

hep-ex↗

arXiv2023

A Superconducting Nanowire Binary Shift Register

We present a design for a superconducting nanowire binary shift register, which stores digital states in the form of circulating supercurrents in high-kinetic-inductance loops. Adjacent superconducting loops are connected with nanocryotrons, three terminal electrothermal switches, and fed with an alternating two-phase clock to synchronously transfer the digital state between the loops. A two-loop serial-input shift register was fabricated with thin-film NbN and achieved a bit error rate less than $10^{-4}$, operating at a maximum clock frequency of $83\,\mathrm{MHz}$ and in an out-of-plane magnetic field up to $6\,\mathrm{mT}$. A shift register based on this technology offers an integrated solution for low-power readout of superconducting nanowire single photon detector arrays, and is capable of interfacing directly with room-temperature electronics and operating unshielded in high magnetic field environments.

physics.app-ph↗

arXiv2023

Large active-area superconducting microwire detector array with single-photon sensitivity in the near-infrared

Superconducting nanowire single photon detectors (SNSPDs) are the highest-performing technology for time-resolved single-photon counting from the UV to the near-infrared. The recent discovery of single-photon sensitivity in micrometer-scale superconducting wires is a promising pathway to explore for large active area devices with application to dark matter searches and fundamental physics experiments. We present 8-pixel $1 mm^2$ superconducting microwire single photon detectors (SMSPDs) with $1\,\mathrm{μm}$-wide wires fabricated from WSi and MoSi films of various stoichiometries using electron-beam and optical lithography. Devices made from all materials and fabrication techniques show saturated internal detection efficiency at 1064 nm in at least one pixel, and the best performing device made from silicon-rich WSi shows single-photon sensitivity in all 8 pixels and saturated internal detection efficiency in 6/8 pixels. This detector is the largest reported active-area SMSPD or SNSPD with near-IR sensitivity published to date, and the first report of an SMSPD array. By further optimizing the photolithography techniques presented in this work, a viable pathway exists to realize larger devices with $cm^2$-scale active area and beyond.

physics.ins-det↗

arXiv2023

Improved heralded single-photon source with a photon-number-resolving superconducting nanowire detector

Deterministic generation of single photons is essential for many quantum information technologies. A bulk optical nonlinearity emitting a photon pair, where the measurement of one of the photons heralds the presence of the other, is commonly used with the caveat that the single-photon emission rate is constrained due to a trade-off between multiphoton events and pair emission rate. Using an efficient and low noise photon-number-resolving superconducting nanowire detector we herald, in real time, a single photon at telecommunication wavelength. We perform a second-order photon correlation $g^{2}(0)$ measurement of the signal mode conditioned on the measured photon number of the idler mode for various pump powers and demonstrate an improvement of a heralded single-photon source. We develop an analytical model using a phase-space formalism that encompasses all multiphoton effects and relevant imperfections, such as loss and multiple Schmidt modes. We perform a maximum-likelihood fit to test the agreement of the model to the data and extract the best-fit mean photon number $μ$ of the pair source for each pump power. A maximum reduction of $0.118 \pm 0.012$ in the photon $g^{2}(0)$ correlation function at $μ= 0.327 \pm 0.007$ is obtained, indicating a strong suppression of multiphoton emissions. For a fixed $g^{2}(0) = 7e-3$, we increase the single pair generation probability by 25%. Our experiment, built using fiber-coupled and off-the-shelf components, delineates a path to engineering ideal sources of single photons.

quant-ph↗

arXiv2022

New constraints on dark matter from superconducting nanowires

Superconducting nanowires, a mature technology originally developed for quantum sensing, can be used as a target and sensor with which to search for dark matter interactions with electrons. Here we report on a 180-hour measurement of a tungsten silicide superconducting nanowire device with a mass of 4.3 nanograms. We use this to place new constraints on dark matter--electron interactions, including the strongest terrestrial constraints to date on sub-MeV (sub-eV) dark matter that interacts with electrons via scattering (absorption) processes.

hep-ph↗

arXiv2022

Reduced ITO for Transparent Superconducting Electronics

Absorption of light in superconducting electronics is a major limitation on the quality of circuit architectures that integrate optical components with superconducting components. A 10 nm thick film of a typical superconducting material like niobium can absorb over half of any incident optical radiation. We propose instead using superconductors which are transparent to the wavelengths used elsewhere in the system. In this paper we investigated reduced indium tin oxide (ITO) as a potential transparent superconductor for electronics. We fabricated and characterized superconducting wires of reduced indium tin oxide. We also showed that a $\SI{10}{nm}$ thick film of the material would only absorb about 1 - 20\% of light between 500 - 1700 nm.

physics.app-ph↗

arXiv2022

A Nanocryotron Memory and Logic Family

The development of superconducting electronics based on nanocryotrons has been limited so far to few-device circuits, in part due to the lack of standard and robust logic cells. Here, we introduce and experimentally demonstrate designs for a set of nanocryotron-based building blocks that can be configured and combined to implement memory and logic functions. The devices were fabricated by patterning a single superconducting layer of niobium nitride and measured in liquid helium on a wide range of operating points. The tests show $10^{-4}$ bit error rates with above $20\,\%$ margins up to $50\,$MHz and the possibility of operating under the effect of a perpendicular $36\,$mT magnetic field, with $30\,\%$ margins at $10\,$MHz. Additionally, we designed and measured an equivalent delay flip-flop made of two memory cells to show the possibility of combining multiple building blocks to make larger circuits. These blocks may constitute a solid foundation for the development of nanocryotron logic circuits and finite-state machines with potential applications in the integrated processing and control of superconducting nanowire single-photon detectors.

physics.app-ph↗

arXiv2022

Determining Dark Matter-Electron Scattering Rates from the Dielectric Function

We show that the rate for dark matter-electron scattering in an arbitrary material is determined by an experimentally measurable quantity, the complex dielectric function, for any dark matter interaction that couples to electron density. This formulation automatically includes many-body effects, eliminates all systematic theoretical uncertainties on the electronic wavefunctions, and allows a direct calibration of the spectrum by electromagnetic probes such as infrared spectroscopy, X-ray scattering, and electron energy-loss spectroscopy (EELS). Our formalism applies for several common benchmark models, including spin-independent interactions through scalar and vector mediators of arbitrary mass. We discuss the consequences for standard semiconductor and superconductor targets, and find that the true reach of superconductor detectors for light mediators exceeds previous estimates by several orders of magnitude, with further enhancements possible due to the low-energy tail of the plasmon. Using a heavy-fermion superconductor as an example, we show how our formulation allows a rapid and systematic investigation of novel electron scattering targets.

hep-ph↗

arXiv2022

Reversible Tuning of Superconductivity in Ion-Gated NbN Ultrathin Films by Self-Encapsulation with a High-$κ$ Dielectric Layer

Ionic gating is a powerful technique for tuning the physical properties of a material via electric field-induced charge doping, but is prone to introduce extrinsic disorder and undesired electrochemical modifications in the gated material beyond pure electrostatics. Conversely, reversible, volatile and electrostatic modulation is pivotal in the reliable design and operation of novel device concepts enabled by the ultrahigh induced charge densities attainable via ionic gating. Here we demonstrate a simple and effective method to achieve reversible and volatile gating of surface-sensitive ultrathin niobium nitride films via controlled oxidation of their surface. The resulting niobium oxide encapsulation layer exhibits a capacitance comparable to that of non-encapsulated ionic transistors, withstands gate voltages beyond the electrochemical stability window of the gate electrolyte, and enables a fully-reversible tunability of both the normal-state resistivity and the superconducting transition temperature of the encapsulated films. Our approach should be transferable to other materials and device geometries where more standard encapsulation techniques are not readily applicable.

cond-mat.supr-con↗

arXiv2022

Free-electron-light interactions in nanophotonics

When impinging on optical structures or passing in their vicinity, free electrons can spontaneously emit electromagnetic radiation, a phenomenon generally known as cathodoluminescence. Free-electron radiation comes in many guises: Cherenkov, transition, and Smith-Purcell radiation, but also electron scintillation, commonly referred to as incoherent cathodoluminescence. While those effects have been at the heart of many fundamental discoveries and technological developments in high-energy physics in the past century, their recent demonstration in photonic and nanophotonic systems has attracted a lot of attention. Those developments arose from predictions that exploit nanophotonics for novel radiation regimes, now becoming accessible thanks to advances in nanofabrication. In general, the proper design of nanophotonic structures can enable shaping, control, and enhancement of free-electron radiation, for any of the above-mentioned effects. Free-electron radiation in nanophotonics opens the way to promising applications, such as widely-tunable integrated light sources from x-ray to THz frequencies, miniaturized particle accelerators, and highly sensitive high-energy particle detectors. Here, we review the emerging field of free-electron radiation in nanophotonics. We first present a general, unified framework to describe free-electron light-matter interaction in arbitrary nanophotonic systems. We then show how this framework sheds light on the physical underpinnings of many methods in the field used to control and enhance free-electron radiation. Namely, the framework points to the central role played by the photonic eigenmodes in controlling the output properties of free-electron radiation (e.g., frequency, directionality, and polarization). [... see full abstract in paper]

physics.optics↗

arXiv2022

A Superconducting Nanowire-based Architecture for Neuromorphic Computing

Neuromorphic computing is poised to further the success of software-based neural networks by utilizing improved customized hardware. However, the translation of neuromorphic algorithms to hardware specifications is a problem that has been seldom explored. Building superconducting neuromorphic systems requires extensive expertise in both superconducting physics and theoretical neuroscience. In this work, we aim to bridge this gap by presenting a tool and methodology to translate algorithmic parameters into circuit specifications. We first show the correspondence between theoretical neuroscience models and the dynamics of our circuit topologies. We then apply this tool to solve linear systems by implementing a spiking neural network with our superconducting nanowire-based hardware.

cs.ET↗

arXiv2022

New Constraints on Dark Photon Dark Matter with Superconducting Nanowire Detectors in an Optical Haloscope

Uncovering the nature of dark matter is one of the most important goals of particle physics. Light bosonic particles, such as the dark photon, are well-motivated candidates: they are generally long-lived, weakly-interacting, and naturally produced in the early universe. In this work, we report on LAMPOST (Light $A'$ Multilayer Periodic Optical SNSPD Target), a proof-of-concept experiment searching for dark photon dark matter in the eV mass range, via coherent absorption in a multi-layer dielectric haloscope. Using a superconducting nanowire single-photon detector (SNSPD), we achieve efficient photon detection with a dark count rate (DCR) of $\sim 6\times10^{-6}$ counts/s. We find no evidence for dark photon dark matter in the mass range of $\sim 0.7$-$0.8$ eV with kinetic mixing $ε\gtrsim 10^{-12}$, improving existing limits in $ε$ by up to a factor of two. With future improvements to SNSPDs, our architecture could probe significant new parameter space for dark photon and axion dark matter in the meV to 10 eV mass range.

hep-ex↗

arXiv2022

Broadband solenoidal haloscope for terahertz axion detection

We introduce the Broadband Reflector Experiment for Axion Detection (BREAD) conceptual design and science program. This haloscope plans to search for bosonic dark matter across the [10$^{-3}$, 1] eV ([0.24, 240] THz) mass range. BREAD proposes a cylindrical metal barrel to convert dark matter into photons, which a novel parabolic reflector design focuses onto a photosensor. This unique geometry enables enclosure in standard cryostats and high-field solenoids, overcoming limitations of current dish antennas. A pilot 0.7 m$^{2}$ barrel experiment planned at Fermilab is projected to surpass existing dark photon coupling constraints by over a decade with one-day runtime. Axion sensitivity requires $<10^{-20}$ W/$\sqrt{\textrm{Hz}}$ sensor noise equivalent power with a 10 T solenoid and 10 m$^{2}$ barrel. We project BREAD sensitivity for various sensor technologies and discuss future prospects.

physics.ins-det↗

arXiv2022

Photon counting from the vacuum ultraviolet to the short wavelength infrared using semiconductor and superconducting technologies

In the last decade, several photon counting technologies have been developed opening a new window for experiments in the low photon number regime. Several ongoing and future projects in HEP benefit from these developments, which will also have a large impact outside HEP. During the next decade there is a clear technological opportunity to fully develop these sensors and produce a large impact in HEP. In this white paper we discuss the need for photon counting technologies in future projects, and present some technological opportunities to address those needs.

physics.ins-det↗